|
II I I 1 1 II 11 it
<br />SECTION 09500
<br />LAY - IN CEILINGS
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />FURNISH LABOR, EQUIPMENT, AND MATERIALS TO COMPLETE THE INSTALLATION OF
<br />ALL LAY -IN CEILING MATERIALS AND SUSPENSION SYSTEMS,
<br />1.01 SUBMITTALS
<br />COMPLY WITH SECTION 10750, SUBMIT SAMPLES FOR APPROVAL,
<br />1.02 JOB CONDITIONS
<br />NO WORK IS TO BE STARTED UNTIL ALL EXTERIOR OPENINGS ARE CLOSED IN,
<br />ALL WET WORK SHALL BE COMPLETED AND DRIED BEFORE WORK IS STARTED,
<br />PART TWO - MATERIALS
<br />2.01 CEILING PANELS
<br />COLOR, TYPE, PATTERN, SIZE, ETC., AS SCHEDULED AND SHOWN ON THE
<br />DRAWINGS, EXPOSED GRID SUSPENSION SYSTEM, CHICAGO METALLIC NO. 200
<br />SERIES SNAP GRID SYSTEM WITH WALL
<br />ANGELS, NO, 1409, L❑-GLOSS WHITE BAKED ENAMEL PAINT FINISH.
<br />PART THREE - EXECUTION
<br />3.01 INSTALLATION
<br />IN STRICT ACCORDANCE WITH MANUFACTURER'S PRINTED INSTRUCTION, SUSPEND
<br />MAIN TEES FROM STRUCTURE USING NO, 9 GAUGE WIRE HANGERS AT 48' CENTER.
<br />LOCK CROSS TEES IN PLACE AT EVERY INTERSECTION WITH MAIN RUNNERS, AND
<br />WALL ANGLES WITH ENDS OF TEES RESTING ON BOTTOM FLANGE, SECURE WALL
<br />ANGLES TO SUBSTRATE WITH SUITABLE FASTENERS AND ANCHORS, SUPPORT ALL
<br />LAY- IN UNITS ON ALL FOR SIDES, PROVIDE EXTRA HANGERS IF REQUIRED.
<br />SUSPEND SURFACE MOUNTED FIXTURES FROM BUILDING STRUCTURE
<br />AND PULL TIGHTLY AGAINST CEILING. COORDINATE WITH THE ELECTRICAL
<br />CONTRACTOR REGARDING SUSPENSION OF ELECTRICAL CEILING FIXTURES FROM THE
<br />CEILING SUSPENSION.
<br />3.02 CLEAN-UP
<br />AT COMPLETION OF THE WORK, REMOVE ALL SCAFFOLDING, CONTAINERS AND
<br />OTHER RUBBISH FROM THIS PORTION OF THE WORK FROM THE SITE. LEAVE ALL
<br />TILE SUPPORTING MEMBERS FIRMLY AND SECURELY ANCHORED, FREE OF FINGER
<br />MARKS OR SMUDGES AND IN PERFECT CONDITION.
<br />DIVISION 10 SPECIALTIES
<br />SECTION 10260
<br />CORNER GUARDS CIF REQUIRED PER DRAWINGS)
<br />PART ONE - GENERAL
<br />1.01 GENERAL
<br />FURNISH LABOR, EQUIPMENT, AND MATERIALS TO COMPLETE THE INSTALLATION OF
<br />ALL RUBBER OR VINYL CORNER GUARDS,
<br />1.01 SUBMITTALS
<br />COMPLY WITH SECTION 10750, SUBMIT SAMPLES FOR APPROVAL.
<br />PART TWO - MATERIALS
<br />2.01 CORNER GUARDS
<br />A. APPROXIMATE SIZE SHALL BE 2' X 2' FULL HEIGHT. COLOR SHALL BE
<br />WHITE OR CLEAR TO MATCH ADJACENT WALL FINISHES. VERIFY COLOR WITH
<br />CONSTRUCTION MANAGER.
<br />B. PROVIDE RUBBER OR VINYL CORNER GUARDS BY ONE OF THE FOLLOWING
<br />MANUFACTURERS OR OWNER APPROVED SUBSTITUTIONS.
<br />1. JOHNSONITE - MIDDLEFIELD, OHI❑ (216-543-8916)
<br />2. ROPPE - FOSTORIA, ❑HIO (419-435-8546)
<br />3. RC MUSSON RUBBER CO., - AKRON, OHI❑ (216-773-7651)
<br />4. MERCER PRODUCTS COMPANY, INC., - ❑RLANDO, FLORIDA (407-578-2900)
<br />C. PROVIDE STAINLESS STEEL CORNER GUARDS CIF REQUIRED PER DRAWINGS)
<br />BY ONE MANUFACTURER'S ALIKE AND AS FOLLOWS, PROVIDE APPROXIMATELY
<br />2' X 2' BY FULL WALL HEIGHT STAINLESS STEEL CORNER GUARDS AT
<br />L❑CATION S AS SHOWN ON THE DRAWINGS BY ONE OF THE FOLLOWING
<br />MANUFACTURERS OR OWNER APPROVED SUBSTITUTIONS,
<br />1, K.J. MILLER CORPORATION, ELKHARD, IN (800-34-7584)
<br />2. PAWLING CORPORATION, PAWLING, NY (914-855-1005)
<br />3. AMERICAN FLOOR PRODUCTS CO., INC. ROCKVILLE, MD (800-342-0424)
<br />4. MCKINNEY/PARKER DIVISION, SCRANTON, PA (717-348-7551) OR
<br />(415-282-7800)
<br />PART THREE - EXECUTION
<br />3.01 GENERAL
<br />INSTALL CORNER GUARDS WHERE NOTED ON THE DRAWINGS AND PER
<br />MANUFACTURER'S WRITTEN INSTRUCTIONS.
<br />SECTION 10290
<br />PEST CONTROL
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />FURNISH LABOR, EQUIPMENT AND MATERIALS TO COMPLETE THE APPLICATION OF
<br />INSECTICIDE.
<br />1.02 SUBMITTALS
<br />COMPLY WITH SECTION 10750, SUBMIT SAMPLES FOR APPROVAL.
<br />PART TWO - MATERIALS
<br />2.01 PEST CONTROL PRODUCT
<br />PERMA-DUST PT240 BORIC - ACID- BASED INSECTICIDE BY WHITMIRE
<br />RESEARCH LABORATORIES INC., ST. LOUIS, MO (314-225-5713), OR OWNER
<br />APPROVED SUBSTITUTION,
<br />PART THREE - EXECUTION
<br />3.01 GENERAL
<br />APPLY AT THE RATE OF 150 SQUARE FEET PER 20 ❑Z., AEROSOL CAN TO FLAT
<br />SIDES OF STUDS OF PERIMETER WALLS, INSIDE OF PERIMETER WALL SHEATHING
<br />TOP SIDE OF GYPSUM BOARD CEILING MATERIAL AND ALL OTHER AREAS CIF ANY)
<br />INDICATED ON THE DRAWINGS. APPLY JUST PRIOR TO COVERING OR ENCLOSING.
<br />APPLY IN STRICT CONFORMANCE WITH MANUFACTURERS RECOMMENDATIONS.
<br />SECTION 10310
<br />TILE BACKER BOARD
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />FURNISH LABOR, EQUIPMENT, AND MATERIALS TO COMPLETE THE INSTALLATION OF
<br />CEMENTI❑US TILE BACKER BOARD
<br />1.02 SUBMITTALS
<br />COMPLY WITH SECTION 10750, SUBMIT SAMPLES FOR APPROVAL,
<br />PART TWO - MATERIALS
<br />2.01 CEMENTIOUS TILE BACKER BOARD
<br />DUROCK CEMENT BOARD - 5/8' THICK - UNITED STATES GYPSUM COMPANY,
<br />P.O. BOX 806278, CHICAGO, IL 60680-4124.
<br />PART THREE - EXECUTION
<br />3.01 GENERAL
<br />APPLY IN LOCATIONS AS DIRECTED IN SECTIONS AND DETAILS. USE POSITIVE
<br />ATTACHMENT OF BUGLE HEAD DRYWALL SCREWS,
<br />EXTERIOR SIGNAGE (IF REQUIRED PER DRAWINGS)
<br />SECTION 10430
<br />EXTERIOR SIGNAGE
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />FURNISH LABOR, EQUIPMENT, AND MATERIALS TO COMPLETE THE INSTALLATION
<br />OF ALL EXTERIOR SIGNAGE.
<br />PART TWO - MATERIALS
<br />2.01 EXTERIOR SIGNAGE
<br />A. OWNER SHALL SUPPLY ALL EXTERIOR SIGNAGE. CONTRACTOR SHALL
<br />INSTALL EXTERIOR SIGNAGE PER MANUFACTURER'S INSTALLATION
<br />INSTRUCTIONS.
<br />B. CONTRACTOR SHALL COORDINATE ELECTRICAL INSTALLATION AND FINAL
<br />ELECTRICAL CONNECTIONS FOR EXTERIOR SIGNAGE UNLESS OTHERWISE
<br />INDICATED.
<br />SECTION 10440
<br />INTERIOR SIGNAGE
<br />CIF REQUIRED PER DRAWINGS)
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />FURNISH LABOR, EQUIPMENT, AND MATERIALS TO COMPLETE THE INSTALLATION
<br />OF ALL INTERIOR SIGNAGE,
<br />PART TWO - MATERIALS
<br />2.01 INTERIOR SIGNAGE
<br />A. OWNER SHALL SUPPLY ALL INTERIOR SIGNAGE, CONTRACTOR SHALL
<br />INSTALL INTERIOR SIGNAGE PER MANUFACTURER'S INSTALLATION
<br />INSTRUCTIONS.
<br />B. CONTRACTOR SHALL SUPPLY AND INSTALL ALL REQUIRED BLOCKING IN
<br />WALLS AS REQUIRED.
<br />C. CONTRACTOR SHALL COORDINATE ELECTRICAL INSTALLATION AND FINAL
<br />ELECTRICAL CONNECTIONS FOR INTERIOR SIGNAGE UNLESS ❑THERWISE
<br />INDICATED.
<br />SECTION 10520
<br />FIRE EXTINGUISHERS
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />FURNISH LABOR, EQUIPMENT, AND MATERIALS TO COMPLETE THE INSTALLATION
<br />OF ALL FIRE EXTINGUISHERS.
<br />PART TWO - MATERIALS
<br />2.01 FIRE EXTINGUISHERS
<br />A. FIRE EXTINGUISHERS SHALL BE MULTIPURPOSE DRY CHEMICAL TYPE RATE
<br />4-A, 60-BC, 10LB. NOMINAL CAPACITY] IN ENAMELED STEEL CONTAINER,
<br />FOR CLASS A, CLASS B AND CLASS C FIRES. PROVIDE MANUFACTURER'S
<br />STANDARD BRACKET FOR EXTINGUISHER UL AND FM LISTED UNIT AS
<br />MANUFACTURED BY ONE OF THE FOLLOWING,
<br />1. J.L. INDUSTRIES
<br />2. LARSEN'S MANUFACTURING COMPANY
<br />3. MUCKLE MANUFACTURING DIVISION OF TECHNICO, INC.
<br />4, PROFILE INTERNATIONAL, INC,
<br />5, BADGER
<br />PART THREE - EXECUTION
<br />3.01 GENERAL
<br />CONTRACTOR SHALL INSTALL FIRE EXTINGUISHERS AS INDICATED ON THE
<br />DRAWINGS OR IF NOT INDICATED ON THE DRAWINGS, AS DIRECTING BY THE
<br />LOCAL FIRE MARSHAL TO COMPLY WITH APPLICABLE GOVERNING REGULATIONS.
<br />SECTION 10800
<br />TOILET ACCESSORIES
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />THE WORK IN THIS SECTION INCLUDES ACCESSORIES IN TOILETS.
<br />PART TWO - MATERIALS
<br />2.01 ACCESSORIES
<br />PR❑VIDE TOILET ACCESSORIES TO MEET AMERICANS WITH DISABILITIES ACT
<br />ACCESSIBILITY GUIDELINES (ADAAG) AS SHOWN ON THE DRAWINGS AND OR
<br />OWNER APPROVED SUBSTITUTIONS.
<br />PART THREE - EXECUTION
<br />3.01 INSTALLATION
<br />ERECT ITEMS IN A RIGID SUBSTANTIAL MANNER, IN CORRECT POSITIONS, AND
<br />LEVEL & PLUM. FULLY TRIM IN WHERE REQUIRED. INSTALL TOILET
<br />ACCESSORIES PER ADAAG GUIDELINES.
<br />DIVISION 11 - EQUIPMENT
<br />SECTION 11400
<br />FOOD SERVICE EQUIPMENT
<br />PART ONE - GENERAL
<br />1.01 SCOPE
<br />A. WHERE FIXED FOOD SERVICE EQUIPMENT ABUTS OTHER EQUIPMENT OR
<br />CONSTRUCTION, SEAL RESULTING JOINT TO MAKE IT SANITARY FOR
<br />CLEANING PURPOSES, PROVIDE BACKER ROD WHEN REQUIRED. USE ONLY
<br />RTV ADHESIVE/SEALANT APPROVED BY NSF
<br />1. SILASTIC 732 DOW CORNING CORPORATION, MIDLAND, MI
<br />(517-496-6000) FOR USE IN FOOD ZONES, PRODUCTS MEETING THIS
<br />REQUIREMENT INCLUDE THE
<br />2. SILITE DEVC❑N CORPORATION, DANVERS, MA (617-777-1100)
<br />FOLL❑WING,
<br />3. RTV100-SERIES, GENERAL ELECTRIC COMPANY, WATERFORD, NY
<br />(518-266-2315)
<br />B. CLEAN AND PRIME OR SPOT PRIME SURFACES TO RECEIVE SEALANT AS
<br />REQUIRED. COLOR TO BE CLEAR OR TO MATCH ADJACENT SURFACES,
<br />C. ITEMS REQUIRING SEALANT INCLUDE, BUT ARE NOT LIMITED TO, THE
<br />FOLLOWING,
<br />1. MOP SINK
<br />2. THREE COMPARTMENT SINK
<br />3. PREP SINK
<br />4. HAND SINKS
<br />5. INSIDE AND OUTSIDE WALK-IN COOLER
<br />6. EXHAUST HOOD
<br />DIVISION 12 - FURNISHINGS
<br />(NOT USED)
<br />DIVISION 13 - SPECIAL CONSTRUCTION
<br />(NOT USED)
<br />DIVISION 14 - CONVEYING SYSTEMS
<br />(NOT USED)
<br />DIVISION 15 - MECHANICAL
<br />(SEE MECHANICAL DRAWINGS)
<br />DIVISION 16 - ELECTRICAL
<br />(SEE ELECTRICAL DRAWINGS)
<br />U8
<br />N
<br />N
<br />0
<br />y
<br />o
<br />00
<br />J
<br />c
<br />�'
<br />JU.
<br />o
<br />�
<br />�
<br />o
<br />N
<br />t0
<br />♦ ^ N
<br />�
<br />CC
<br />C
<br />�
<br />o
<br />¢
<br />O
<br />r
<br />o_
<br />0
<br />JM
<br />J
<br />LL
<br />rn
<br />0
<br />a�
<br />Ua
<br />> o
<br />O r
<br />Lo
<br />o
<br />z
<br />o
<br />c
<br />�
<br />a
<br />c
<br />N
<br />J
<br />C
<br />J
<br />O Q
<br />y
<br />o
<br />J
<br />ti
<br />L
<br />U
<br />C
<br />CC
<br />t`
<br />0
<br />0
<br />N
<br />J�04
<br />J >
<br />cci
<br />W W
<br />o
<br />.J
<br />N Q D LL,
<br />O
<br />a. m J
<br />�_-CLJ
<br />J =
<br />w
<br />U
<br />="_
<br />a
<br />U
<br />WOOw
<br />NCDN
<br />Revisions:
<br />W
<br />Z
<br />060
<br />Q
<br />� U
<br />LL
<br />O _
<br />ZU
<br />W
<br />CL
<br />W
<br />Project Number
<br />07059
<br />Date
<br />02-28-08
<br />Sheet Number
<br />G1.4
<br />
|