7325 Gall Blvd (6) - Laserfiche WebLink

Browse Search

I _ _ _____ __L_ SCOPE OF WORK FOR ALL DISCIPLINES ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR TO WALK THE SITE WITH THE HOBBY LOBBY ON -SITE SUPERINTENDENT AND VERIFY ALL EXISTING CONDITIONS PRIOR TO BID. • INCLUDE LABOR IN JOB TO COMPLETE YOUR SCOPE OF WORK IN THE TIME ALLOWED BY FIELD SUPERINTENDENT. • CLEAN UP DAILY OR MORE OFTEN IF NECESSARY TO KEEP SITE CLEAN AND SAFE. • CONTRACTOR TO SUPPLY AS -BUILT DRAWINGS AT COMPLETION OF PROJECT. • ALL INFORMATION WILL BE PROVIDED TO ON -SITE SUPERINTENDENT OR THEIR REPRESENTATIVE. • CONTRACTOR TO BID COMPLETE SET OF DRAWINGS / ALL SHEETS. • SUBCONTRACTOR MUST PROVIDE PAYMENT AND PERFORMANCE BOND FOR ANY WORK OVER $100,000.00. CONTRACTOR TO SHOW BOND PRICE IN BID. BOND MUST BE RECEIVED BY HOBBY LOBBY WITH IN 5 BUSINESS DAYS AFTER CONTRACT RECEIVED. • CONTRACTOR MUST INCLUDE AND SHOW SALES TAX ON BIDS. • CONTRACTOR IS TO PLACE ALL DEBRIS IN THE G.C. PROVIDED DUMPSTER. DRYWALL AND FRAMING ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • A MINIMUM OF 20 GAUGE METAL TO BE USED ON ALL FRAMING COMPONENTS. • REFER TO PLANS FOR LOCATIONS OF HEAVIER GAUGE METALS TO BE USED. • DRYWALL TO BE 5/8" TYPE X, UNLESS NOTED OTHERWISE, TAPED, BEDDED WITH MEDIUM KNOCK DOWN TEXTURE READY FOR PAINT. • 5/8" GREEN BOARD OR "M.R.S." (MOISTURE RESISTANT SHEET ROCK) IN REST ROOMS ON WALLS THAT ARE WITHIN 4'-O" OF ANY PLUMBING FIXTURES. • FURNISH AND INSTALL F.R.P., GLUE MUST BE APPLIED WITH A TROWEL NO EXCEPTIONS. INSTALL F.R.P. CORNERS, JOINTS AND CEILING TRIM CUT TRIM 4" ABOVE FINISH FLOOR FOR COVE BASE INSTALLATION. WHERE APPLICABLE AS SHOWN ON PLANS. • CEILING TILE TO BE ARMSTRONG 2911 PROVIDED BY G.C. • SUBCONTRACTOR TO FURNISH AND INSTALL VINYL CLAD DRYWALL CEILING TILE. • HARD CEILING AND METAL DECKS TO BE TIED TO ROOF STRUCTURE WITH CEILING WIRE AND 1 1 /2" COLD ROLLED STEEL. USE STRUCTURAL GAUGE METAL DECKING ABOVE CASH OFFICE. • CHECK LOCAL CODES FOR SPECIAL CONDITIONS ON CEILING GRID INSTALLATION. • FURNISH LABOR TO INSTALL DOORS, JAMBS AND HARDWARE. • FURNISH LABOR TO INSTALL O.S.B. WAINSCOT IN WAREHOUSE. • FURNISH AND INSTALL WOOD BACKING AT DOOR JAMBS, TOILET PARTITIONS, BABY CHANGING STATION, T.V., TOILET ACCESSORIES, CABINETS, STORE FRONT, AND SIGNAGE IF APPLICABLE. • FURNISH AND INSTALL WOOD BLOCKING AND CORNICE FRAMING AT TOP OF PARAPET WALLS IF SHOWN ON PLANS. (ALTERNATE PROPOSAL) • INSTALLATION OF RESTROOM PARTITIONS AND ALL TOILET ACCESSORIES. • INCLUDE CEILING GRID IN DRYWALL PROPOSAL. • INCLUDE ALL EXTERIOR FRAMING, SHEATHING, AND MOISTURE BARRIER ON ALL EXTERIOR FRAMEWORK. • USE FIRE RATED CAULKING ON FIRE RATED WALLS, WHERE REQUIRED. • INSULATE ALL WALLS BELOW CEILING GRID BETWEEN OFFICES, RETAIL, AND RESTROOM WALLS ADJACENT TO STAGING AREA AS SHOWN ON PLANS. • LABOR AND FASTENERS TO INSTALL G.C. SUPPLIED CABINETS AND SHELVING. • FURNISH AND INSTALL CEILING WIRE AT ALL LIGHT FIXTURE CEILING BRACKETS. COORDINATE EXACT LOCATION WITH ELECTRICIAN. PLUMBING ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • SAW CUTTING AND REMOVAL OF CONCRETE SLAB AS NEEDED FOR NEW IN GROUND PLUMBING. REPLACE WITH CONCRETE OF EQUAL DEPTH AND STRENGTH, DOWEL EDGES OF SLAB 16" O.C. USING 1 /2" X 2' REBAR. • CAP ALL UNUSED PLUMBING LINES A MINIMUM OF 4" BELOW FINISH FLOOR, NO CONCRETE TO BE POURED INTO ABANDONED LINES. • CAMERA ALL NEW LINES AT COMPLETION OF JOB ON GROUND UP CONSTRUCTION. CAMERA ALL EXISTING LINES AT BEGINNING AND END OF JOBS TO BE REUSED. PROVIDE TAPE OR DVD TO GENERAL CONTRACTOR. • HOT WATER TANK TO BE ELECTRIC AS SPECIFIED. CONTRACTOR TO INSTALL CONDENSATE LINES IF NECESSARY. • HANDICAP SINKS TO RECEIVE WRAPPING ON EXPOSED PIPING PER CODE. • CAP ALL WATER LINES THAT ARE ABANDONED AND REMOVE ALL ABANDONED PIPING. • PROVIDE TRAP PRIMERS ON ALL FLOOR DRAINS. • IF PLANS INDICATE PRESSURE ASSIST TANKS ON WATER CLOSETS VERIFY THAT THE HANDICAP HAVE THE SAME. • GAS PIPING ON ROOF TO BE FASTENED DOWN TO APPROVED OR SPECIFIED BLOCKING. • IF A HIGH PRESSURE GAS LINE SYSTEM IS USED THE REGULATORS AND SHUT-OFF VALVES WILL BE FURNISHED BY GAS PIPE INSTALLER. • IDENTIFY LOCATION OF GAS, WATER AND IRRIGATION SERVICE AND METERS. • CONFIRM NO CROSS CONNECTIONS ON NATURAL GAS SYSTEM OR WATER TO ADJACENT SPACES IF APPLICABLE. • IDENTIFY ANY SUB -METERS INSTALLED ON WATER SYSTEM AND DESCRIBE THEIR PURPOSE. • IDENTIFY LOCATION OF ALL BACK -FLOW PREVENTERS, I.E. FIRE SYSTEMS, IRRIGATION, DOMESTIC WATER, ETC. AND TESTING IF APPLICABLE. • SUBMITTALS FOR ANY NEW FIXTURES AND EQUIPMENT TO BE SUPPLIED TO HOBBY LOBBY PRIOR TO INSTALLATION. • SUBCONTRACTOR TO DO ALL EXCAVATING, COMPACTING AND BACK FILLING NECESSARY. • SUBCONTRACTOR RESPONSIBLE FOR ALL BACKING NECESSARY TO COMPLETE HIS WORK. PLUMBING (GROUND UP) • ALL PIPES SHALL BE CUT OFF AT LEAST 1" BELOW FINISH FLOOR WITH A COUPLING TO TIE INTO AND EXTEND UP AFTER FLOOR AND WALLS HAVE BEEN POURED. • PLACE 12" SONA-TUBE AROUND EACH PIPE FILLED WITH SAND TO 1" BELOW FINISH FLOOR. • AFTER WALLS HAVE BEEN ERECTED LOCATE ALL PIPES AND BREAK OUT CONCRETE COVERING THEM AND EXTEND UP ABOVE FLOOR. • ALL WATER LINES SHALL BE COPPER AND RAN OVERHEAD. • ALL WATER LINES SHALL BE HUNG ON APPROVED HANGERS AND INSULATED. • ALL PVC SHALL BE SCHEDULE 40. CONCRETE ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR TO SUPPLY HOBBY LOBBY WITH MIX DESIGN OF CONCRETE FROM SUPPLIER OR SUPPLIERS PRIOR TO THE POURING OF ANY CONCRETE. ALLOW 2 WEEKS LEAD TIME FOR ENGINEERS APPROVAL. • IF CONTRACTOR USES ANY COMPANY OR INDIVIDUAL AS A SUBCONTRACTOR TO COMPLETE ANY PORTION OF THEIR CONTRACT, THEY MUST NOTIFY HOBBY LOBBY WITH PROOF OF THEIR INSURANCE PRIOR TO DOING ANY WORK ON THE JOB. • CONTRACTOR TO SUPPLY AND INSTALL ALL STEEL REINFORCEMENT TO BE USED ON THIS PROJECT. CONTRACTOR IS RESPONSIBLE FOR ANY FABRICATION TO FORM INTO SHAPES AND LENGTHS REQUIRED. • CONTRACTOR TO SUPPLY ALL CONCRETE, MATERIALS, AND LABOR TO COMPLETE THIS PROJECT. (ANY EXCLUSION MUST BE NOTED ON CONTRACT) • G.C. WILL HAVE A SURVEYOR SET PINS FOR BUILDING CORNERS, PIERS, BACK OF CURBS, LIGHT POLE BASES, LOADING DOCK WALLS AND REFERENCE FOR OTHER POINTS ALONG WITH ELEVATIONS. IT IS THE CONTRACTORS RESPONSIBILITY TO SET BATTER BOARDS OR LINES FOR OTHER TRADES TO USE TO ESTABLISH THE LOCATIONS NEEDED FOR INSTALLATION OF OTHER'S ITEMS AS REQUIRED. • CONTRACTOR IS TO LAYOUT AND PLACE ALL EMBEDS AND ANCHOR BOLTS IN CONCRETE AS SHOWN BY DRAWINGS. • CONTRACTOR TO FURNISH AND PUT TO GRADE ALL MATERIALS NEEDED TO BRING SUB GRADE TO FINAL GRADE ONCE SUB GRADE HAS BEEN BROUGHT TO PLUS (+) OR MINUS (-) A TENTH OF A FOOT. • ANY MATERIALS EXCAVATED BY CONTRACTOR ARE TO BE MOVED TO AN AREA DESIGNATED BY SUPERINTENDENT TO BE USED FOR BACK FILL LATER. (ALL SPOILS TO BE REMOVED FROM JOBSITE BY CONTRACTOR) • CONTRACTOR TO EXCAVATE DIRT BETWEEN PIERS FOR PANELS THEN BACKFILL AND COMPACT ALL AREAS NEXT TO ANY AND ALL WALLS. • CONTRACTOR TO FURNISH AND INSTALL ALL SHIMS AND REBAR PINS TO ENSURE LINE AND GRADE OF PANELS. • CONTRACTOR TO MARK PANEL LOCATIONS AND TO HAVE A PERSON PRESENT WHEN PANELS ARE BEING SET TO SURVEY IN PANELS TO ENSURE THEY ARE SET TRUE TO LINE AND GRADE. • CONTRACTOR WILL BE RESPONSIBLE FOR ENGINEERING OF LIFTING POINTS AND BRACING OF PANELS. • CONTRACTOR WILL FURNISH AND INSTALL ALL EMBEDS FOR LIFTING AND BRACING. • CONTRACTOR WILL CLEAN ALL EMBEDS AND REMOVE ANY INSPECTED BY ERECTOR PRIOR TO LIFTING OF ANY PANELS TO INSURE THEY ARE PROPERLY CLEANED AND NO DAMAGE HAS ACCRUED TO LIFTING AND BRACING EMBEDS. • CONTRACTOR TO SET NUTS ON ANCHOR BOLTS TO GRADE READY FOR PLACEMENTS OF COLUMNS. • CONTRACTOR WILL BE RESPONSIBLE FOR ANY CHARGES INCURRED DUE TO ANCHOR BOLTS OR EMBED BEING OFF FROM WHERE SHOWN ON DRAWINGS. • WHEN PANELS ARE SET AND STEEL ERECTED CONTRACTOR TO FURNISH AND POUR CONCRETE ON BOTH SIDES OF PANEL JOINTS TO SECURE THEM. THIS IS TO BE DONE BEFORE ANY BRACING IS REMOVED. ITEMS TO INCLUDE IN YOUR BID • CONTRACTOR TO FURNISH AND INSTALL ANY BLOCK OUTS FOR PLUMBING, ELECTRICAL OR ANCHOR BOLTS. THESE ARE TO BE SET AT GRADE NOT TO EXCEED 1" BELOW FINISH FLOOR AND FILLED WITH SAND TO TOP OF FORM. CONCRETE TO BE POURED OVER THESE. ONCE PANELS ARE LIFTED THESE ARE TO BE CLEANED OUT SO ANY OTHER WORK CAN BE DONE AND THEN FILLED BACK WITH CONCRETE ONCE FINISHED. • CONTRACTOR TO FURNISH AND INSTALL NON -SHRINK GROUT UNDER ALL COLUMNS. • ANY JOINTS WHERE POURS MEET ON FLOOR MUST BE A FLAT SURFACE AND ANY RAISED AREAS WILL BE GROUND BACK FLAT BY CONTRACTOR. • CONTRACTOR WILL FILL ALL PENETRATIONS MADE IN FLOOR. -ALL EMBEDS FOR LIFTING OR BRACING THAT WILL BE EXPOSED ABOVE DECK OR IN STAGING AREA WILL BE FILLED IN TO MAKE A SMOOTH SURFACE. • PANEL EDGES ON THE EXTERIOR WHERE TWO PANELS MEET WILL HAVE A CHAMFERED EDGE. HOBBY LOBBY WILL FURNISH DETAIL. • ANY IMPERFECTIONS IN PANELS THAT ARE EXPOSED TO OUTSIDE OF BUILDING WILL EITHER BE RUBBED OR FILLED SO THAT THEY WILL NOT. SHOW AFTER PAINTED AND/OR TEX-COATED. • CONTRACTOR TO SAW CUT ALL CONCRETE AS LAID OUT ON PLANS. THIS IS TO BE DONE AS SOON AS IT CAN BE DONE WITHOUT CAUSING ANY DAMAGE TO CONCRETE. NOT TO EXCEED 8 HOURS AFTER FINISHING. ANY DUSTS FROM SAWING TO BE SWEPT OFF OF SLAB TO ENSURE CLEAN SURFACE FOR PANELS. • SAW JOINTS WHERE PANELS ARE TO BE POURED ON TOP OF SLAB ARE TO BE FILLED WITH PATCHING CEMENT SO NOT TO TRANSFER TO PANELS AS A DEFECT OR LINE. • CONTRACTOR TO SAW CUT PANELS AT 18" ABOVE DECK BEARING ELEVATION FOR TERMINATION BAR OF ROOFING (WHEN APPLICABLE). THIS IS TO BE DONE BEFORE LIFTING OF PANELS. • CONTRACTOR TO CAULK A LINE ON PANELS BEFORE LIFTING AT DECK BEARING ELEVATION TO CHECK THAT ALL EMBEDS ARE AT PROPER HEIGHTS. THIS IS TO KEEP FROM HAVING ANY DELAYS DURING ERECTION OF BUILDING. • ALL CURBS ARE TO BE POURED AS EITHER A CURB AND GUTTER, OR MONOLITHIC WITH PARKING. CURBS MUST BE FORMED TO ENSURE A UNIFORM SHAPE. • CONTRACTOR TO FURNISH HOBBY LOBBY WITH A SCHEDULE OF WORK TO ENSURE IT MEETS OUR FAST TRACK SCHEDULE AND FOR THE SCHEDULING OF OTHER TRADES. • LOADING DOCK WALLS AND LIGHT POLE BASES WILL BE HAND RUBBED TO A TEXTURE FINISH AS TO NOT SHOW ANY DEFECTS. • CONTRACTOR IS RESPONSIBLE FOR ANY PRICE INCREASE OR OTHER CHARGES INCURRED TO MAINTAIN THE SCHEDULE OF THIS PROJECT. THESE CHARGES WILL NOT BE PASSED ON TO HOBBY LOBBY. • CONTRACTOR WILL BE RESPONSIBLE FOR PUMPING OF WATER THAT MIGHT BE TRAPPED IN BLOCK OUTS FOR COLUMNS, LOADING DOCK OR STORM DRAINS UNTIL THEY HAVE COMPLETED THEIR WORK IN THOSE AREAS. • CONTRACTOR IS TO PAY FOR ALL DRILLING OF PIERS, PUMPING OF CONCRETE, OR THAT OF ANY OTHER EQUIPMENT USED TO COMPLETE THEIR CONTRACT. • CONTRACTOR TO INSTALL ALL ANCHOR BOLTS FOR LIGHT POLES. OTHERS WILL SUPPLY BOLTS AND LOCATION. • ALL FINISHES AND TOLERANCES ARE TO BE AS SPELLED OUT IN SPEC. BOOK. • CONTRACTOR TO SUPPLY AND APPLY A RELEASING COMPOUND WHERE PANELS ARE POURED ON SLAB. THIS IS TO BE APPLIED HEAVY ENOUGH TO ENSURE THAT PANELS WILL NOT STICK. IF COST IS INCURRED DUE TO STICKING OF PANELS, IT WILL BE THE RESPONSIBILITY OF THE CONTRACTOR TO PAY FOR THIS AT NO ADDITIONAL COST TO HOBBY LOBBY. ANY DAMAGE TO CONCRETE DUE TO THE STICKING PANELS WILL BE REPLACED OR REPAIRED BY CONTRACTOR. • CONTRACTOR WILL BE RESPONSIBLE FOR ANY BARRICADES TO PREVENT TRAFFIC FROM DRIVING ON PARKING UNTIL IT HAS CURED TO A POINT TO RECEIVE TRAFFIC. • CONTRACTOR TO INSTALL ALL G.C. SUPPLIED EMBEDS. • CONTRACTOR TO INSTALL ALL G.C. SUPPLIED PIPE BOLLARDS. • CONTRACTOR TO BLOCK OUT ALL OPENINGS IN PANELS ON PANEL BOOKS. THESE ARE TO BE SECURED TO MAKE SURE THEY ARE SQUARE. H.V.A.C. ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR AWARDED CONTRACT TO INSTALL NEW LENNOX R.T.U. EQUIPMENT SHALL COMPLY WITH LENNOX, HOBBY LOBBY, AND NATIONAL/LOCAL CODE INSTALLATION CRITERIA. • ANY EXISTING HEATING AND COOLING EQUIPMENT BEING USED ON THE BUILDING IS TO BE INSPECTED USING THE HOBBY LOBBY CHECKLIST SHEET AT THE START OF THE CONSTRUCTION PROJECT (WITHIN 2 WEEKS) AND A DETAILED LIST OF REPAIRS ALONG WITH AN ESTIMATE SENT TO HOBBY LOBBY FOR EVALUATION BY THE H.V.A.C. MANAGER. UPON NOTIFICATION OF BID ACCEPTANCE, CONTRACTOR HAS 2 WEEKS TO INSPECT ALL EXISTING H.V.A.C. EQUIPMENT, NOT BEING REPLACED, AND SUBMIT AN EVALUATION REPORT AND BID FOR REPAIRS TO G.C. EVALUATION MUST BE RECORDED IN FULL ON A HOBBY LOBBY EQUIPMENT EVALUATION FORM. FAILURE TO DO SO MAY AFFECT RETAINAGE IF ANOTHER CONTRACTOR MUST BE CALLED IN TO PERFORM THIS TASK. EVALUATIONS NEED ONLY TO BE COMPLETED ON EQUIPMENT NOT TO BE REPLACED. • MECHANICAL CONTRACTOR IS RESPONSIBLE FOR ASSEMBLY, SPOTTING, INTERNAL INSULATION, AND LEVELING OF ROOF CURBS. INSULATION MATERIAL USED FOR THE INTERIOR SPACE OF THE R.T.U. CURBS WILL BE THE MECHANICAL CONTRACTOR'S RESPONSIBILITY TO FURNISH AND INSTALL. • CUT DECKING AT CURBS FOR DUCT WORK INSTALLATION AND ON NEW R.T.U. UNITS HVAC CONTRACTOR SHALL INCLUDE SPACE FOR INSTALLATION OF 1" CONDUIT BY ELECTRICAL CONTRACTOR FOR CABLING REQUIREMENTS. (SEE ELECTRICAL SCOPE OF WORK) • MECHANICAL CONTRACTOR WILL BE RESPONSIBLE FOR COORDINATION OF R.T.U. DELIVERY TO JOBSITE WITH JOB SUPERINTENDENT AND LENNOX. EQUIPMENT SHOULD BE TRANSFERRED BY CRANE FROM THE DELIVERY TRUCK TO THE R.T.U. CURB AND NOT STORED ON THE GROUND. • SET ROOF TOP UNITS. • SMOKE DETECTORS ON ALL EXISTING R.T.U.S (NOT GROUND UP CONSTRUCTION) SHALL BE REPLACED BY THE MECHANICAL CONTRACTOR AND MEET LOCAL SMOKE DETECTOR FIRE CODES. SMOKE DETECTORS TO BE FURNISHED BY HOBBY LOBBY AND INSTALLED BY MECHANICAL CONTRACTOR UNLESS NOTED OTHERWISE. • INSTALL THERMOSTATS AND / OR AUTOMATION SENSORS. TERMINATE WIRING TO REQUIRED UNITS AND THERMOSTATS. • LENNOX UNITS WITH BELT DRIVE BLOWER MOTORS ARE SHIPPED WITH THE DRIVE PULLEY IN THE OPEN POSITION. CONTRACTOR MUST ALIGN AND ADJUST PULLEY TO WITHIN 1 TURN OF THE CLOSED POSITION AND THOROUGHLY TIGHTEN THE SETSCREW LOCKING THE ADJUSTMENT IN PLACE. FAILURE TO ADJUST WILL CAUSE THE UNIT TO CYCLE ON LOW PRESSURE DUE TO LOW AIR MOVEMENT. ONLY EXCEPTION, IF CERTIFIED AIR BALANCE IS PERFORMED AND PULLEY HAS BEEN SET BY THE CERTIFIED BALANCING PROCEDURE TO A DIFFERENT POSITION. • G.C. WILL WIRE UNITS TO THE BUILDING AUTOMATION SYSTEM. CHECK FOR REQUIREMENT BY SUBCONTRACTOR. (REFER TO DRAWINGS) • JOBS WITH UNUSED OR DEMISED DUCTING INN THE CEILING CAVITY SHALL HAVE SAID DUCT REMOVED BY THE MECHANICAL CONTRACTOR UNLESS STATED OTHERWISE. • FURNISH AND INSTALL ALL NECESSARY DUCTWORK PER DESIGN ENGINEER SPECIFICATIONS USING HARD ROUND OR RECTANGLE DUCT (A MAXIMUM OF 6 FOOT OF FLEX MAY BE USED PER RUN BETWEEN DIFFUSER AND METAL PIPE) OR PER CODE. BALANCING DAMPERS ARE TO BE INSTALLED IN EACH SUPPLY DUCT RUN FOR BALANCING PURPOSES. DAMPERS TO BE INSTALLED AT THE END OF THE HARD PIPE DUCT RUN AND BEFORE THE FLEX DUCT CONNECTION TO THE DIFFUSER. METAL ELBOWS SHALL BE USED IN A WAY TO KEEP FLEXIBLE DUCT CONNECTIONS STRAIGHT BETWEEN ROUND METAL SUPPLY DUCTING AND THE SUPPLY GRILLE. NO ELLS ARE TO BE FORMED WITH FLEXIBLE DUCTING. • FURNISH AND INSTALL ALL DIFFUSERS. BALANCE AIRFLOW TO EACH REGISTER. • RECOVER ALL REFRIGERANT IN ABANDONED UNITS. (CONTRACTOR TO SUPPLY REFRIGERANT INCIDENT REPORT TO HOBBY LOBBY VERIFYING EQUIPMENT DISPOSAL.) • UNITS 7.5 TON AND LARGER WITH CONCENTRIC AIRFLOW DESIGN SHALL USE RECTANGLE METAL CONNECTIONS PER THE M-2 DRAWINGS. ABSOLUTELY NO FLEXIBLE ROUND DUCT OR RIGID ROUND DUCT CONNECTIONS IN ANY CONFIGURATION WILL BE ACCEPTED BETWEEN THE UNIT AND CONCENTRIC PACKAGES. • MECHANICAL CONTRACTOR SHALL BE RESPONSIBLE FOR SPOTTING AND COORDINATING INSTALLATION OF EXHAUST FAN CURB/S WITH THE ROOFING CONTRACTOR. • CONTRACTOR SHALL COMPLETE HOBBY LOBBY NEW EQUIPMENT START UP CHECK LIST WHEN INSTALLATION IS COMPLETE. THE COMPLETED FORM, FOR EACH UNIT, IS TO BE GIVEN TO THE HOBBY LOBBY SUPERINTENDENT WITH ALL INFORMATION RECORDED FOR REVIEW. • CONTRACTOR TO MAINTAIN A CLEAN WORK ENVIRONMENT AND REMOVE TRASH AND DEBRIS FROM WORK AREA DAILY. ANY CHARGES FOR ROOF REPAIR OR CLEAN UP CREATED DUE TO NEGLIGENCE WILL BE WITHHELD FROM CONTRACTORS' RETAINAGE, NO EXCEPTIONS. • NUMBERING OF H.V.A.C. EQUIPMENT TO MATCH HOBBY LOBBY DRAWING AND PERFORMED BY H.V.A.C. CONTRACTOR PER SHEET BAS1. • MECHANICAL CONTRACTOR WILL COORDINATE WITH ROOFER THE PLACEMENT OF CURBS AND CUTTING OF THE DECKING MATERIAL. • STORES WITH OPEN CEILINGS AND CONCENTRIC AIR DISTRIBUTION DESIGN WILL HAVE CONCENTRIC SUPPLIES INSTALLED IN A MANNER TO PREVENT SUPPLY AIR FROM DISCHARGING DIRECTLY ON LIGHT FIXTURES. THE TOP OF THE SUPPLY DISCHARGE OPENING SHOULD BE MOUNTED NO HIGHER THAN THE BOTTOM OF ALL LIGHTING FIXTURES. • INSTALL DUCTWORK IN OPEN CEILING BEFORE PAINT AND INSTALL DUCTWORK IN GRID CEILING BEFORE GRID INSTALLATION. • MECHANICAL CONTRACTOR WILL BE RESPONSIBLE TO PERFORM TWO FILTER CHANGES IN ALL R.T.U. UNITS OPERATED DURING CONSTRUCTION, USING PLEATED FILTERS WITH A RATING OF NO LESS THAN A MERV 7. FIRST CHANGE TO BE PERFORMED AT THE HEIGHT OF CONSTRUCTION DEMO WITH THE SECOND AFTER FIXTURING BEFORE STORE OPENING. UNLESS SPECIFIED ELSEWHERE,MECHANICAL E CHANI CAL CONTRACTOR SHALL BE RESPONSIBLE FOR CONDENSATE DRAINS MEETING LOCAL AND NATIONAL CODES. SUPPORTS SHALL BE OF TYPE IDENTIFIED ON M-2 DRAWINGS AND ATTACHED TO ROOF MEMBRANE IN A MANNER NOT TO AFFECT ROOF WARRANTY AND TO PREVENT PIPING FROM MOVING OR SAGGING. • LAY IN SUPPLY DIFFUSERS SHALL BE INSTALLED WITH AN INSULATED METAL ELBOW CONNECTING FROM THE FLEXIBLE DUCT DROP TO THE MATCHING THROAT SIZE OF THE DIFFUSER. DIFFUSER BACKING SURFACE SHALL ALSO BE OF THE INSULATED VARIETY OR INSULATED BY THE MECHANICAL CONTRACTOR. • EQUIPMENT TO BE REPLACED OR REMOVED FROM STRUCTURE SHALL BE DISPOSED OF IN ACCORDANCE WITH APPROPRIATE EPA GUIDELINES. PROPER DOCUMENTATION WILL BE FURNISHED TO HOBBY LOBBY DESCRIBING MEANS OF RECOVERY AND DISPOSAL • MECHANICAL CONTRACTOR WILL BE RESPONSIBLE FOR INSTALLATION OF FILTER MEDIA, FURNISHED BY HOBBY LOBBY, TO ALL RETURN GRILLES OR UNFINISHED RETURN DUCT OPENINGS OF R.T.U.'S OPERATED DURING CONSTRUCTION. NO UNIT SHALL BE RUN DURING CONSTRUCTION WITHOUT THIS PRECAUTION BEING ADHERED TO. • MECHANICAL CONTRACTOR WILL COORDINATE WITH JOB SUPERINTENDENT THE ISOLATION AND PROTECTION OF RETURN AIR SMOKE DETECTOR SAMPLING TUBES AND SENSING CHAMBER IMMEDIATELY AFTER PLACEMENT OF EQUIPMENT ON THE ROOF, BEFORE STARTUP. CONTRACTOR WILL BE HELD LIABLE FOR SMOKE DETECTOR FAILURE IF THIS PROCEDURE IS NOT FOLLOWED - NO EXCEPTIONS. PROCEDURE TO BE REVERSED BY THE MECHANICAL CONTRACTOR BEFORE COMMISSIONING OF FIRE ALARM AND TESTING L ES G OF SMOKE DETECTORS. • AS-BUILTS ARE TO BE COMPLETED AND TURNED INTO THE HOBBY LOBBY SUPERINTENDENT AT COMPLETION OF JOB. • HVAC CONTRACTOR SHALL WIRE A THERMOSTAT FOR ALL EXISTING AND NEW UNIT HEATERS. ELECTRICAL ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • DEMO ALL UNUSED PANELS. • DEMO ALL POWER COMING UP THRU FLOOR. • DISCONNECT (SAFE OFF) ALL ELECTRICAL IN WALLS AND LIGHTING TO BE REMOVED. • RELOCATE ANY PANELS POSSIBLE NEEDED TO ACCOMMODATE NEW CIRCUITS. WIRE AND INSTALL ALL OWNER PROVIDEDPOWER OWER POLES PER PLANS. • WIRE AND INSTALL ALL OWNER PROVIDED PLUG MOLD PER PLANS. • WIRE AND INSTALL ALL 3 PHASE 208 OR 480 CIRCUITS TO ROOF TOP UNITS. (DISCONNECT PROVIDED IN ALL NEW ROOF TOP UNITS.) CONTRACTOR TO PROVIDE EXTERNAL DISCONNECT IF REQUIRED BY CODE. • PROVIDE WIRE TO AND INSTALL WEATHER PROOF G.F.I. CIRCUITS PER LOCAL CODE ON R.T.U.'S. • A 1" CONDUIT IS TO BE INSTALLED ON ALL EXISTING AND NEW R.T.U'S FOR THE PURPOSE OF ROUTING ALL COMMUNICATION AND LOW VOLTAGE WIRING. CONDUIT SHALL CONNECT FORM INSIDE THE ELECTRICAL COMPARTMENT OF R.T.U. PENETRATING THE ROOF DECK AND TO EXTEND NO LESS THAN 18" BELOW THE ROOF DECK. CONDUIT ENDS SHALL HAVE A CONNECTOR AND BUSHING ON EACH END. • PROVIDE ALL CONDUIT STUBS FOR PHONE, DATA, T.V., CAMERAS, ALARMS OR OTHER DEVICES PER PLANS. • PROVIDE WIRE TO AND INSTALL BUZZER SYSTEM TO TRUCK DOCK ENTRANCE PER PLANS. • PROVIDE WIRE TO AND INSTALL BUZZER SYSTEM FOR STORE EMPLOYEE ENTRANCE PER PLANS. • WIRE CIRCUIT TO BALER PER PLANS AND FURNISH DISCONNECT. • WIRE CIRCUIT TO COMPACTOR PER PLANS AND FURNISH DISCONNECT. • WIRE (3) 120 VOLT 20 AMP CIRCUITS TO SIGNAGE PER PLANS WITH JUNCTION BOXES. • PROVIDE WIRE TO INSTALL (1) 120 VOLT 20 AMP DEDICATED CIRCUIT FOR SECURITY SYSTEM. • PROVIDE WIRE TO INSTALL (1) 120 VOLT 20 AMP DEDICATED CIRCUIT FOR FIRE ALARM SYSTEM. • WIRE AND INSTALL ALL OWNER PROVIDED LIGHT FIXTURES PER PRINT. • SUPPLY UNI-STRUT AND FIXTURE CHAIN ON LIGHT FIXTURES IN SALES AREA. (OPEN CEILING SYSTEMS ONLY) ALL LIGHTING TO BE LEVEL AND STRAIGHT. • PROVIDE AND INSTALL (2) 3" CONDUITS FROM TELEPHONE BOARD TO DECK FOR HOBBY LOBBY INSTALLED LOW VOLTAGE WIRING. • ELECTRICAL CONTRACTOR SHALL INSTALL OWNER PROVIDED LIGHTING CONTACTOR PANEL (L.C.O.). ALL BUILDING AUTOMATION SYSTEM INTERIOR AND EXTERIOR LIGHTING, POWER POLES, AND CEILING PLUGS ARE TO BE CONNECTED IN THE .C.P. THEN ROUTED BACK TO APPROPRIATE BREAKER PANEL. • ELECTRICAL CONTRACTOR SHALL PROVIDE 120 VAC POWER TO L.C.P. ALSO PROVIDE PVC RACEWAY TO EXTEND FROM THE TOP LEFT OF THE L.C.P. UP THROUGH THE DROP CEILING OR CEILING GIRDER WHICH EVER IS REQUIRED. • INVESTIGATE M.D.P. FOR LIGHTING CONTROL CIRCUITS FOR EXTERIOR LIGHTING CIRCUITS, DESIGNATE, AND MARK. • INVESTIGATE TO ASSURE NO OTHER BUILDINGS OR AREAS ARE BEING SUPPLIED FROM HOBBY LOBBY ELECTRICAL SWITCH. • TEMPORARY LIGHTING AS NEEDED FOR CONSTRUCTION PURPOSES. • IDENTIFY AND MARK ALL SERVICE GEAR AND PANELS WITH TYPED PRINT. • RENTAL EQUIPMENT • ELECTRICAL PERMIT • ALL DEMO WIRING AND PANELS ARE THE PROPERTY OF HOBBY LOBBY. • IDENTIFY ELECTRIC SERVICE AND METER SUPPLYING POWER TO LOCATION. • CONFIRM NO CIRCUITS FEED POWER TO ADJACENT SPACE OR EXTERIOR OF BUILDING FROM DISTRIBUTION PANELS, I.E. PARKING LOT LIGHTING, PEDESTAL SIGNS, ETC. • IDENTIFY ANY SUB -METERS ON UTILITY SERVICE AND THEIR PURPOSE • REQUEST THE MOST CURRENT FIXTURE PLAN FROM SUPERINTENDENT BEFORE INSTALLING THE HOME RUNS TO THE POWER POLES AND ANY FIXTURE DISPLAY. • ALL SENSOR, COMMUNICATION, (SECURITY AND FIRE AS NEEDED) CABLES SHALL BE PULLED THROUGH 1" CONDUIT INTO R.T.U. CABLES ARE NOT TO BE STRETCHED, NICKED, OR CUT. CABLES IS TO BE ROLLED UP AND TAPED INSIDE OF UNIT. • ALARM DRAWINGS PROVIDED BY HOBBY LOBBY. PROVIDE CONDUIT AND J-BOXES WHERE REQUIRED FOR CEILING HORNS, PULL STATIONS, CONTROL PANEL AND KEY PAD. IF ALARM PLAN IS UNAVAILABLE OR NOT ATTACHED TO THE SET OF PLANS AT THE TIME OF BIDDING ONE WILL BE PROVIDED TO ELECTRICAL CONTRACTOR. • WIRE EXHAUST FAN FOR RESTROOMS AND CONFIRM VOLTAGE WITH H.V.A.C. CONTRACTOR. • WIRE WATER HEATER FOR RESTROOMS AND CONFIRM VOLTAGE WITH PLUMBING CONTRACTOR. • PROVIDE AND INSTALL (1) 3" CONDUIT FROM ALARM PANEL TO BOTTOM OF BAR JOISTS. VERIFY LOCATION ON PLANS. • PROVIDE TEMPORARY 200 AMP PANEL LOCATED IN THE CENTER OF THE STORE WITH 20 CIRCUITS FOR CONTRACTOR USE. • PROVIDE A SEPARATE PRICE FOR EXTERNAL DISCONNECT WHICH MAY BE REQUIRED BY CODE. • NUMBERING OF R.T.U.'S ARE TO FOLLOW BUILDING AUTOMATION SYSTEM DRAWING. • AS-BUILTS ARE TO BE COMPLETED AND TURNED INTO THE HOBBY LOBBY SUPERINTENDENT AT COMPLETION OF JOB. • 10 TON LENNOX R.T.U. DISCONNECTS SHALL BE LOCATED AS INDICATED (SEE DETAIL SHEET 5-E3). • TWO (22) FOUR SQUARE BOXES (ONE ABOVE THE OTHER CONNECTED BY [" CONDUIT) WITH S/G PLASTER RING (5/8" RAISE) SHALL BE MOUNTED ON COLUMNS WITH THERMOSTATS. TWO [" CONDUITS OUT OF THE TOP OF THE BOX SHALL BE EXTENDED 6 INCHES ABOVE CEILING GRID. CONDUIT END SHALL HAVE A CONNECTOR AND BUSHING ON EACH END. • A (2-") FOUR SQUARE BOX WITH S/G PLASTER RING (NO RAISE) SHALL BE MOUNTED FOR UNIT HEATER SENSORS PER E1 OR BUILDING AUTOMATION SYSTEM DRAWINGS. A [" CONDUIT OUT OF THE TOP OF THE BOX IS TO BE EXTENDED NO LESS THAN 1 FOOT FROM THE DECK. CONDUIT END SHALL HAVE A CONNECTOR AND BUSHING ON EACH END. • ALL BREAKERS ARE TO BE LABELED. • ELECTRICAL CONTRACTOR SHALL INSTALL OWNER PROVIDED VERIS METER AT SERVICE ENTRANCE FEEDING MAIN DISTRIBUTION PANEL. THE VERIS METER IS TO BE POWERED WITH A 3-PHASE 20 AMP BREAKER. • PROVIDE ADD ALTERNATE TO FURNISH AND INSTALL CEILING WIRE AT ALL LIGHT FIXTURE CEILING BRACKETS. SPRINKLER ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • PRIOR TO STARTING WORK CONTRACTOR SHALL SEND TWO COPIES OF PLANS TO CORPORATE OFFICE FOR OUR REVIEW AND RECORDS. SEND TO CONSTRUCTION DEPARTMENT CONTRACTOR ADMINISTRATOR: 7707 S.W. 44TH STREET, OKLAHOMA CITY, OKLAHOMA 73179. • PROVIDE AND INSTALL VALVED TEST CONNECTIONS FOR SYSTEM AS REQUIRED. • NECESSARY ENAMEL SIGNS SHALL BE INSTALLED ON CONTROL VALVES, DRAINS, AND INSPECTOR'S TEST IN ACCORDANCE WITH GOVERNING BODIES SPECIFICATIONS. • CONTRACTOR IS RESPONSIBLE FOR INSTALLING FIRE SUPPRESSION SYSTEM PER GOVERNING AGENCY. • CONTRACTOR RESPONSIBLE FOR ALL PERMITS, LICENSE AND OBTAINING APPROVED DRAWINGS FOR GOVERNING AGENCY. • CONTRACTOR TO DESIGN LOCATION OF SPRINKLER HEADS TO AVOID CONFLICT WITH LAYOUT OF LIGHT FIXTURES AND CEILING GRID. LIGHT FIXTURE LAYOUT WILL STAY AS DESIGNED AND NOT BE MOVED. SPRINKLER HEADS WILL BE ADJUSTED ACCORDINGLY AROUND FIXTURE LAYOUT. • CONTRACTOR IS RESPONSIBLE FOR STANDARD PIPE CONNECTION, CONNECTION TO THE BUILDING, AND BRINGING MAIN INTO BUILDING AT SPECIFIED STUB UP. OWNER PROVIDES WATER MAIN LOCATED 5' OUTSIDE OF BUILDING LINE. CONTRACTOR IS RESPONSIBLE FOR EXCAVATION AND BACKFILL. • CONTRACTOR TO PROVIDE BACK FLOW PREVENTER IF REQUIRED BY NATIONAL CODE OR CITY REQUIREMENTS. • CONTRACTOR IS RESPONSIBLE FOR ALL TESTS TO MEET GOVERNING CODES. • CONTRACTOR TO PROVIDE ALL TAMPER AND FLOW VALVES NECESSARY FOR SYSTEMS. • CONTRACTOR WILL BE REQUIRED TO BE AVAILABLE AT THE JOB SITE FOR ALL SPRINKLER AND ALARM RELATED INSPECTIONS. RE -INSPECTIONS ARE INCLUDED ALSO. • P.I.V., F.D.C. AND ASSOCIATED BACK FLOWS PROVIDED IF REQUIRED. • CONTRACTOR TO FURNISH AND INSTALL BOX FOR SPARE HEADS AND WRENCHES. • ALL AREAS WITH A GRID CEILING AND SURFACE MOUNTED LIGHTS SHALL HAVE A PENDANT TYPE SPRINKLER HEAD WITH A 2 PIECE ESCUTCHEON THAT HANGS DOWN BELOW THE CEILING SO THAT LIGHTS WILL NOT INTERFERE WITH THE COVERAGE. ALL LAYOUT OF SPRINKLERS MUST MATCH HOBBY LOBBY LIGHTING LAYOUT. • ALL SPRINKLERS SHALL BE COORDINATED TO MISS THE CEILING GRID. • SPRINKLERS SHALL BE SPACED IN ACCORDANCE WITH THE LIGHTING AND MECHANICAL EQUIPMENT. LIGHTING AND MECHANICAL EQUIPMENT PLACEMENT SHALL HAVE PRIORITY OVER THE SPRINKLER PIPING. SPRINKLER PIPES SHALL NOT PENETRATE AIR DUCTS OR STRUCTURAL MEMBERS. PROVIDE ADDITIONAL SPRINKLERS AROUND MECHANICAL EQUIPMENT, PIPING, DUCTWORK AND OTHER OBSTRUCTIONS AS REQUIRED BY NFPA 13. • PROVIDE CEILING ACCESS DOORS WHERE REQUIRED TO ACCESS VALVES OR OTHER ITEMS REQUIRING MAINTENANCE IN PLASTER CEILINGS. ALL ACCESS DOORS SHALL BE SIZED AND LOCATED TO PERMIT EASY ACCESS TO THE ITEMS REQUIRING MAINTENANCE. CEILING ACCESS DOORS SHALL BE 24" x 24" MINIMUM. • ALL PIPING SHALL BE CONCEALED ABOVE CEILING OR IN WALL SPACES UNLESS OTHERWISE NOTED. THE ROUTING OF ALL EXPOSED PIPING SHALL BE REVIEWED AND APPROVED IN THE FIELD BY HOBBY LOBBY PRIOR TO INSTALLATION. • ALL EXPOSED SPRINKLER PIPING DOES NOT NEED TO BE PAINTED UNLESS REQUIRED BY LOCAL CODE. IF SPRINKLER PIPE PAINTING IS REQUIRED ALL PIPING SHALL BE THOROUGHLY CLEANED BEFORE IT IS PAINTED. INSTALL CHROME ESCUTCHEONS AT ALL EXPOSED WALL PENETRATIONS. SLEEVE AND SEAL WALL AND FLOOR PENETRATIONS AS SPECIFIED. • ALL WALL PENETRATIONS OF FIRE RATED ASSEMBLIES SHALL BE SEALED AS SPECIFIED. VERIFY LOCATION OF ALL FIRE RATED WALLS AND FLOORS WITH OWNER. SEAL ALL REVEALING WALL PENETRATIONS & CAULK. SEE SPECIFICATIONS. ALL SPRINKLER PIPING SHALL BE INSTALLED AT SUCH T T C H HE SYSTEM WILL COMPLETELY DRAIN BACK TO THE MAIN. IF A SECTION OF PIPING CANNOT BE SLOPED BACK TO THE MAIN, AN AUXILIARY DRAIN VALVE WITH PERMANENT LABEL AND HOSE THREAD CONNECTION MUST BE INSTALLED. ALL AUXILIARY DRAINS SHALL BE CONCEALED FROM OCCUPIED SPACES. • FIRE PROTECTION CONTRACTOR SHALL PERFORM FLOW TEST TO VERIFY AVAILABLE FLOW PRIOR TO PREPARING HYDRAULIC CALCULATIONS. STEEL ERECTION ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR TO SCHEDULE UNLOADING OF ALL STEEL DELIVERED TO SITE AND STAGE IN DESIGNATED AREA. • CONTRACTOR IS TO PROVIDE ALL EQUIPMENT AND LABOR NECESSARY FOR INSTALLATION OF ALL STEEL AND ANY WORK RELATED TO CONTRACT. • CONTRACTOR IS TO CONFIRM MATERIAL LIST AT TIME OF OFF LOAD. SHORTAGES SHOULD BE NOTED ON DELIVERY TICKET. • CONTRACTOR WILL BE REQUIRED TO CONFIRM PANEL LAYOUT WITH CONCRETE CONTRACTOR. • CONTRACTOR IS REQUIRED TO INSTALL ALL R.T.U. STRUCTURAL FRAMING SHOWN ON PRINTS AND COORDINATE WITH H.V.A.C. CONTRACTOR. • PANEL ERECTING IS TO BE INCLUDED ALONG WITH BRACING. • CONTRACTOR TO INCLUDE PRICE FOR RAILING AND JIB CRANE INSTALLATION. E.I.F.S. ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR IS TO PROVIDE ALL NECESSARY EQUIPMENT TO COMPLETE THE JOB. • CONTRACTOR IS REQUIRED TO KEEP PRODUCT OFF OF OTHER MATERIALS AND SURFACES. • CONTRACTOR MUST VERIFY E.I.F.S. COLORS THROUGH HOBBY LOBBY BEFORE ORDERING MATERIALS. • CONTRACTOR IS TO PROVIDE A PRICE FOR WEATHER PROTECTION IF IT BECOMES NECESSARY. • CONTRACTOR IS REQUIRED TO USE SENERGY OR DRYVIT FINISH PRODUCTS. MASONRY ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR TO PROVIDE ALL MATERIALS AND LABOR AS SPECIFIED. • CONTRACTOR IS TO PROVIDE ALL EQUIPMENT NECESSARY INCLUDING SCAFFOLDING TO COMPLETE THE JOB. • CONTRACTOR IS TO PROVIDE A COST FOR WINTERIZATION AS AN ALTERNATE. • CONTRACTOR IS TO BE RESPONSIBLE FOR STORAGE OF HIS MATERIALS AND SUPPLIES ON THE JOB SITE. • CONTRACTOR IS RESPONSIBLE FOR REMOVING WATER, SILT, SLUDGE, SAND, OR DIRT THAT HAS ACCUMULATED ON FOOTING DURING CONSTRUCTION WORK IN ORDER TO PROCEED WITH HIS OWN WORK. • CONTRACTOR IS TO PROVIDE AND INSTALL ALL STEEL LINTELS, REBAR AND DRY STACK STONES. • MASONRY CONTRACTOR IS RESPONSIBLE FOR ALL BRACING NECESSARY FOR THE WALLS. • CONTRACTOR IS TO PROVIDE AND INSTALL WEEP HOLES WHERE SHOWN ON DRAWINGS. • CONTRACTOR IS RESPONSIBLE FOR CLEANING OUT MASONRY EXPANSION JOINTS BEFORE THE WATERPROOFING OF EXPANSION JOINT WITH CAULKING. • CONTRACTOR IS RESPONSIBLE FOR REMOVAL OF EXCESS GROUT IN JOIST POCKETS. • CONTRACTOR IS RESPONSIBLE FOR INSTALLATION OF ALL EMBED PLATES AND ANCHOR BOLTS. • CONTRACTOR IS RESPONSIBLE FOR FILLING CELLS WITH GROUT PER STRUCTURAL DRAWINGS AND APPLICABLE CODES PER CITY AND STATE. • CONTRACTOR IS RESPONSIBLE FOR MATCHING COLOR OF MASONRY AND GROUT. • PROVIDE SAMPLE PANEL OF MASONRY PRODUCTS IF REQUIRED. STOREFRONT ITEMS TO INCLUDE IN YOUR BID IF NOTE ALREADY NOTED ON PLANS: • CONTRACTOR IS TO PROVIDE SILL PLATE AT BOTTOMS OF ALL MULLIONS. • CONTRACTOR IS TO PROVIDE CLOSED BACK JAMB FOR INSTALLATION OF AUTOMATIC DOORS. • VERIFY ON PRINTS, ANY TINTING REQUIREMENTS BY CODE. • WHEN USING 4 1 /2" INCH MULLIONS YOU WILL BE REQUIRED TO WET SET INSIDE OF RAILS AND STILES BEFORE SETTING GLASS. • CONTRACTOR IS TO PROVIDE ALL CAULKING AROUND PERIMETER OF GLASS STOREFRONT INSIDE AND OUT. • CONTRACTOR WILL BE REQUIRED TO INSTALL STOREFRONT BEFORE AUTOMATIC DOORS ARE INSTALLED. VERIFY FINISHED OPENING BEFORE MANUFACTURING. • VERIFY THAT ALL FRAMES AND GLAZING MEET APPLICABLE CODES. ROOFING ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR IS RESPONSIBLE FOR INSTALLATION OF WOOD NAILERS AND PLYWOOD AT THE TOP OF C.M.U., TILT UP WALL, E.I.F.S., AND STRUCTURAL FRAMING AND BID AS AN ADD ALTERNATE. • CONTRACTOR IS REQUIRED TO PROVIDE ALL NECESSARY PADS UNDER GAS LINES, CONDENSATE LINES, AND WALK PADS. • CONTRACTOR IS TO PROVIDE THE ROOF WARRANTY TO HOBBY LOBBY IN THE OWNER'S NAME AND ADDRESS. VERIFY COVERAGE REQUIRED (I.E. 15 OR 20 YEAR WARRANTY) • CONTRACTOR IS REQUIRED TO USE HICKMAN FLASHING, OR APPROVED EQUAL, WHERE DESIGNATED ON PRINTS. • CONTRACTOR IS REQUIRED TO FILL IN METAL DECKING BEFORE RE -ROOFING OVER (ON REMODELS). • CONTRACTOR IS RESPONSIBLE FOR ALL GUTTERING AND DOWNSPOUTS AS PER PLANS. PROVIDE ADAPTORS AT BOTTOM OF DOWNSPOUT TO STORM SEWER SYSTEM IF REQUIRED. • CONTRACTOR WILL BE REQUIRED TO DO A FINAL SWEEP AFTER STORE IS COMPLETED TO REPAIR DAMAGE OR FAULTY INSTALLATION. A ROOF DAMAGED BY NEGLIGENCE WILL BE BACK CHARGED TO RESPONSIBLE PARTY. • CONTRACTOR MUST PROVIDE AND INSTALL EXPANSION JOINTS, VERTICAL AND HORIZONTAL WHEN REQUIRED. THEY MUST BE INSTALLED PER DETAILS ON DRAWINGS. PAINTING ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • CONTRACTOR IS REQUIRED TO PROVIDE ALL EQUIPMENT AND MATERIALS NECESSARY TO COMPLETE JOB. • CONTRACTOR IS RESPONSIBLE FOR KEEPING ALL PAINT OFF OF FLOORS, PARAPETS, AND BAR JOISTS. • CONTRACTOR WILL BE REQUIRED TO CAULK ALL PRODUCTS FINISHED TO: F.R.P., METAL JAMBS, CABINETS, ETC. • ALL WALLS, COLUMNS, AND PEG WILL BE REQUIRED TO HAVE ONE COAT PRIMER AND TWO COATS FINISH. • CONTRACTOR IS REQUIRED TO SUBMIT EXTERIOR PAINT SAMPLES TO BE APPROVED BY HOBBY LOBBY. • ALL PAINT MATERIALS TO BE PURCHASED FROM SHERWIN WILLIAMS. OIL BASE IS REQUIRED ON ALL METAL. SEMI -GLOSS LATEX IS REQUIRED ON ALL WALLS INCLUDING STAGING AREA WALLS. C.M.U. AND CONCRETE WALLS ARE NOT REQUIRED TO BE PAINTED IF NEW ONLY IF PREVIOUSLY PAINTED. IF PAINTED, BLOCK FILLER MUST BE INCLUDED. • CONTRACTOR NEEDS TO REPLACE CEILING TILE IF REMOVED WHILE PAINTING. • CONTRACTOR IS REQUIRED TO IDENTIFY ALL TOUCH UP PAINT WITH PERMANENT MARKER FOR STORE MANAGER. REMOVE ALL OTHER PAINT AND MATERIALS FROM JOB SITE AND DISPOSE OF AV PROPERLY. CH -UP PAINT. LEAVE TOUCH-UP • ALL SPRINKLER HEADS ARE TO BE PROTECTED FROM PAINT OVER SPRAY AND THE METHOD OF PROTECTION OR COVERING REMOVED. • PAINT ALL EXPOSED METAL ON ROOF INCLUDING ROOF HATCH AND BRACES. • PAINT ALL GAS LINES ON ROOF. • IN AN OPEN OR EXPOSED CEILING SITUATION CONTRACTOR IS TO PROTECT OR CLEAN FLOORING AND ALL AREAS NOT TO RECEIVE PAINT. ALARM SYSTEMS ITEMS TO INCLUDE IN YOUR BID IF NOT ALREADY NOTED ON PLANS: • ALARM CONTRACTOR TO BID AND INSTALL SYSTEM PER HOBBY LOBBY ALARM CONTRACTOR FIELD PACK. p+enb412 hitecture gineering 710 West Roselawn Drive Rogers, Arkansas 72756 Phone: 479.636.3545 Fax: 479.636.1209 William Douglas Hurley Florida License No AR91919 Firm License No: AA26000940 W �� ~w wpzN (n o Lnows �N<-ao zaF zwt�w¢3 W w �V)LX a5�poo< aQ E=zQN= Of a oa O Loa ¢c�a``'ac~io�o !i a CJ .z,z�� w�F U X O 3w�W��oowawCr LU acr~oa 00- z�� oa��z� Qzv)nw8o v� w� ocno aaSaz V- ZF-J�C7F- 0_ 00Xww<w`o�wWZ �m �wazl-'~ow�'ooc�ao} U7 F-�ii�n(Aa.z>iraawoaM >M I M 0 w Q Q ~ JO 1Z )LL illiiiiiiiiiiiiiiiiiiiiii O 0(6 m J �_ J 2 Q r>_W 'o Ly(D= CL=�MCO N 0 M (` w �� as 0 ti ISSUE BLOCK CHECKED BY: DF DRAWN BY: JCF FILE NAME: G1.1 DOCUMENT DATE: 08-09-13 I .0 DID NOTES I I . SHEET: G1.1 1 -