|
Ljk�"'llwa 1
<br />m
<br />N
<br />Z
<br />V)
<br />D
<br />0
<br />In
<br />N
<br />0
<br />N
<br />0
<br />N
<br />DIVISION NO, 8 DOORS AND WINDOWS:
<br />008400 ENTRANCES, STOREFRONT AND WINDOWS:
<br />A. DESIGN REQUIREMENTS:
<br />EXTERIOR WALLS:
<br />1. DESIGN COMPLETED STOREFRONT SYSTEM TO WITHSTAND WIND LOADS
<br />NORMAL TO WALL PLANE INDICATED.
<br />2. POSITIVE PRESSURE - MEET LOCAL CODE REQTS.
<br />3. NEGATIVE PRESSURE - MEET LOCAL CODE REQTS.
<br />INTERIOR WALLS:
<br />1. 10 PSF - ACTING IN EITHER DIRECTION.
<br />PROVISIONS FOR THERMAL MOVEMENT TO HANDLE 180' F. SURFACE
<br />TEMPERATURE RANGE AND/OR CHANGE WITHOUT CAUSING
<br />BUCKLING STRESSES ON GLASS, JOINT SEAL FAILURE, UNDUE STRESS
<br />ON STRUCTURAL ELEMENTS, DAMAGING LOADS ON FASTENERS, REDUCTION
<br />OF PERFORMANCE OR DETRIMENTAL EFFECTS.
<br />B. PERFORMANCE REQUIREMENTS:
<br />1. STATIC PRESSURE AIR INFILTRATION - 0.06 CFM MAXIMUM ® DIFFERENTIAL
<br />STATIC PRESSURE OF 1.57 PSF PER ASTM E 283-84.
<br />2. STATIC PRESSURE WATER INFILTRATION (CONDENSATION ON INDOOR FACE OF
<br />AND CONPOMENT ONLY) ® TEST PRESSURE EQUAL TO 10% POSITIVE WIND
<br />PRESSURE DESIGN BUT NOT LESS THAN 6.24 PSF PER ASTM E331-86. NO
<br />UNCONTROLLED WATER WILL BE USED FOR TEST PURPOSES.
<br />3. CONTAIN WATER PENETRATING STOREFRONT SYSTEM WITHIN SYSTEM BY GUTTERS,
<br />DRAIN TO EXTERIOR THROUGH WEEP HOLES. NO UNCONTROLLED WATER INFILTRATION
<br />IS ALLOWABLE.
<br />C. WARRANTY:
<br />1. DOOR HARDWARE - ONE YEAR EXCEPT FIVE YEARS ON CLOSERS.
<br />2. WATERTIGHTNESS OF SYSTEM - TWO YEARS.
<br />3. FINISH - MANUFACTURER'S STANDARD FINISH WARRANTY.
<br />D. ACCEPTABLE MANUFACTURERS:
<br />1. YKK CORP.
<br />2. KAWNEER CORP.
<br />3. PPG INDUSTRIES, INC.
<br />4. VISTAWALL ARCH. PRODUCTS, INC.
<br />5. TUBELITE, INC.
<br />E. MATERIALS:
<br />1. DOORS, DOOR FRAME AND TRIM MOLDINGS SHALL BE EXTRUDED FROM
<br />6063-T5 ALUMINUM ALLOY & TEMPER. ASTM B 221 ALLOY H.A. 1OA-T5.
<br />2. GLAZING GASKETS FOR DOORS AND FRAMES SHALL BE ELASTOMERIC
<br />EXTRUDED GASKETS. ALL SCREWS AND MISC. FASTENERS SHALL BE OF ALUMINUM,
<br />STAINLESS OR ZINC PER ASTM A164
<br />FINISH: ELECTROLYTICALLY DEPOSITED COLOR - AA-M12C22A42/44 - STATUARY
<br />BRONZE #40 OR CLEAR ANODIZED #17 FINISH.
<br />F. COMPONENTS:
<br />1. ENTRANCE DOORS - MED. STILES - BOT RAIL 10"
<br />INSTALL %" DIAMETER ALUM ROD W/THREADED ENDS & NUTS CAD TOP
<br />BOTTOM RAILS TO ANCHOR STILES TOGETHER FOR DOOR STABILITY.
<br />2. STORE FRONT - EQUAL TO TRIFAB 451 (KAWNEER)- 1 -Y4" x 4 Y2".
<br />3. ALUMINUM ENTRANCE HARDWARE:
<br />a. 1 )t PR HEAVY DUTY PINNED HINGES (SAME FIN AS DOOR)
<br />b. 1 EA. PUSH/PULL - F2 (KAWNEER)
<br />c. 1 EA. THRESHOLD - NGP
<br />d. 1 EA. CYLINDER - 1 73 - KEY OPERATED ® EXTERIOR AND
<br />THUMBTURN OPERATION ON INSIDE. FINISH TO MATCH DOORS.
<br />DIVISION NO. 8 DOORS AND WINDOWS:
<br />008700 FINISH HARDWARE:
<br />A. REFERENCE FINISH HARDWARE SCHEDULE AND DOOR AND FRAME SCHEDULE IN
<br />THE CONSTRUCTION DOCUMENTS.
<br />DIVISION NO. 8 DOORS AND WINDOWS:
<br />008800 GLASS AND GLAZING:
<br />A. INDUSTRY STANDARDS:
<br />1. ANSI: SAFETY PERFORMANCE STANDARDS AND METHODS OF TESTS FOR SAFETY
<br />GLAZING MATERIALS USED IN BUILDINGS, Z97.1 1984.
<br />2. ALI DIRECTORY, MARCH 1981 EDITION
<br />3. CPSC: SAFETY STANDARD FOR ARCHITECTURAL GLAZING MATERIALS, 16 CFR
<br />PART 1201, JANUARY 1986 EDITION.
<br />4. FGMA:; GLAZING MANUAL, 1986 EDITION AND SEALANT MANUAL, 1983 EDITION.
<br />5. GTA: ENGINEERING STANDARDS MANUAL.
<br />6. IGCC: CERTIFIED PRODUCTS DIRECTORY.
<br />B. WARRANTY: MANUFACTURER'S STANDARD WARRANTY; TO START ® DATE OF
<br />SUBSTANTIAL COMPLETION.
<br />C. MATERIALS:
<br />1.
<br />CLEAR TEMPERED GLASS .- INTERIOR:
<br />a. THICKNESS: Y4" SINGLE GLAZE; AND, 1" DOUBLE GLAZE, TINTED ASTM
<br />C1048-85, KIND HT, TYPE I, CLASS 1, QUALITY q3, CONDITION A, B
<br />OR C FOR FINAL USE.
<br />b. SGCC CERTIFICATION. LABEL OR BUG, LOCATED IN LOWER RIGHT HAND
<br />CORNER OF PARALLEL TO FLOOR IN INCONSPICUOUS LOCATION.
<br />2.
<br />Y4" WIRE GLASS:
<br />a. DIAMOND OR MISCO -MESH, ASTM C1036-85, TUPE II, CLASS 1, FORM
<br />1, QUALITY q8, MESH ML, ANSI Z97.1 1984.
<br />b. UL LISTED AS FIRE RETARDANT.
<br />3.
<br />THERMAL INSULATING UNITS:
<br />a. TEMPERED UNITS W/ THERMAL BARRIER:
<br />(1) INBOARD LITE: 1 /4", CLEAR TEMPERED GLASS.
<br />(2) OUTBOARD LITE: Y4" TINTED, TEMPERED GLASS.
<br />(3) TOTAL UNIT THICKNESS: 1"
<br />(4) TINT WILL BE MFR'S STANDARD BRONZE OR GREY.
<br />b. SPACER: METAL COMPLETE WITH DESICCANT; SIZE TO
<br />PRODUCE INDICATED AIR SPACE.
<br />c. PRIMER SEAL: POLYISOBUTYLENE; CONTINUOUSLY APPLIED
<br />EACH SIDE OF SPACER TO BOND SPACER TO EACH LITE.
<br />d. SECONDARY SEAL: SILICONE, SIMILAR TO GE SILICONE SCS
<br />3211, SILICONE CONSTRUCTION SEALANT. BONDS TO BOTH
<br />METAL SPACER & GLASS LITE TO FORM A 3-SIDE BOND.
<br />4.
<br />ASSEMBLED UNIT PERFORMANCE VALUES:
<br />a. CLEAR AND TINTED UNITS:
<br />(1) DAYLIGHT TRANSMITTANCE: 40%
<br />(2) U-VALUE:
<br />(a.) WINTER, NIGHT - 0.48
<br />(b.) SUMMER; DAY - 0.58
<br />(c) SHADING COEFFICIENT - 0.58
<br />(3) COMPLY WITH ASTM E774.
<br />5.
<br />ACCESSORIES:
<br />a. SETTING BLOCKS: NEOPRENE, 70-90
<br />DUROMETER HARDNESS, ASTM D1056-78.
<br />b. GLAZING SEALANT: DOW CHEMICAL - NO.
<br />999 SILICONE RUBBER SEALANT.,
<br />GE - SILICONE CONST. SEALANT 1200.,
<br />TREMCO, INC. PROGLAZE.
<br />PREFORMED BUTYL OR BUTYLISOBUTYLLENE
<br />TAPE, 100% SOLIDS, COLOR TO MATCH GLASS TINT.
<br />POLYVINYL CHLORIDE FOAM TAPE - CLOSED
<br />CELL, SELF-ADHESIVE TAPE, ASTM D1667-76
<br />DIVISION NO. 9 FINISHES:
<br />009260 GYPSUM
<br />BOARD SYSTEM:
<br />A. MATERIALS:
<br />1,
<br />FIRE RESISTANT/RATED GYPSUM BOARD:
<br />a. ASTM C636-85
<br />b. FED SPEC SS-L-30D
<br />C. TYPE III, GRADE X, CLASS 1, FORM C,
<br />d. %" THICKNESS, TAPERED EDGES.
<br />2.
<br />MOISTURE & MOLD RESISTANT GYPSUM BOARD:
<br />a. ASTM C 1396 (SECTION 5), ASTM C630, ASTM D3273, & ASTM C473
<br />b. FED SPEC. SS-L-30D
<br />C. TYPE VIi, GRADE W OR X, CLASS 2, %" THICKNESS
<br />d. REGULAR AND/OR FIRE RESISTANT GYPSUM BOARD.
<br />3.
<br />CEMENTITIOUS BACKER .UNITS:
<br />a. ANSI A108.11, A118.9
<br />b. ASTM C1325, E136
<br />C. %" FIBER MAT REINFORCED SHEATHING
<br />d. Ws" UNDERLAYMENT
<br />e. USGS DUROCK OR APPROVED EQUAL.
<br />4.
<br />MANUFACTURERS:
<br />a. DOMTAR GYPSUM
<br />b. GEORGIA PACIFIC CORP.
<br />C. GOLD BOND/NATIONAL GYPSUM CO.
<br />d. U.S. GYPSUM.
<br />5.
<br />CONTROL JOINT
<br />a. ASTM C 1047
<br />b. ASTM C 840
<br />C. E-Z STRIP EXPANSION JOINT OR APPROVED EQUAL.
<br />d. MAX. OF 30' BETWEEN CONTROL JOINTS.
<br />e. LOCATE ABOVE IN -LINE W/DOOR JAMB WHEN POSSIBLE
<br />DIVISION NO. 9 FINISHES:
<br />009310 TILE:
<br />A. STANDARDS:
<br />1. ANSI - SPECS
<br />2. TCA - HANDBOOK
<br />B. MATERIALS
<br />1. PRE -SELECTED BY OWNER
<br />2. DAL TILE - PORCELAIN PATTERN AS INDICATED IN
<br />INTERIOR COLOR SCHEDULE
<br />DIVISION NO. 9 FINISHES:
<br />009510 ACOUSTICAL CEILINGS:
<br />A. MATERIALS
<br />1. PRE -SELECTED BY OWNER - REFER TO THE INTERIOR COLOR
<br />SCHEDULE
<br />a. COORDINATE WITH SHEET A-5
<br />2. ARMSTRONG WORLD INDUSTRIES, INC.
<br />B. EXPOSED GRID METAL SUSPENSION SYSTEMS:
<br />1. 15y6" x 1 1Z" HIGH (MAIN TEE HGT.) EXPOSED GRID, FACTORY PAINTED
<br />WHITE.
<br />2. EDGE MOLD: MINIMUM 0.020" THICKNESS STEEL, CHANNEL OR ANGLE
<br />SHAPED WITH MINIMUM %" FLANGE WIDTH, HEMMED EDGE, FACTORY
<br />PAINTED WHITE.
<br />3. 12 GAUGE HANGER WIRE SPACED A MAX. OF 4' O.C. PER ASTM C636
<br />PER MANUFACTURES RECOMENDATIONS
<br />C. ACOUSTICAL SEALANT:
<br />1. PECORA CORP: BA-98
<br />2. TREMCO, INC. - ACOUSTICAL SEALANT
<br />3. GE - SILICONE.
<br />4. NON -HARDENING, NON -SKINNING, SYNTHETIC RUBBER.
<br />DDIVISION NO. 9 FINISHES:
<br />009670 FLUID -APPLIED FLOORING:
<br />A. MATERIALS
<br />1. PRE -SELECTED BY OWNER - REFER TO THE INTERIOR COLOR
<br />SCHEDULE.
<br />2. GENERAL POLYMERS OR APPROVED EQUAL.
<br />B. STANDARDS
<br />1. ASTM
<br />2. ACI
<br />C. TESTING & PREPARATION
<br />1. FLOOR SLAB MOISTURE VAPOR EMISSION TEST PRIOR TO INSTALLATION
<br />2. REMOVAL & REPLACEMENT OF NON -DURABLE CONCRETE.
<br />3. DECONTAMINATION OF CONCRETE SURFACE.
<br />4. REPAIR OF SURFACE IRREGULARITIES.
<br />DIVISION NO. 9 FINISHES:
<br />009680 CARPET:
<br />00••0•
<br />A. STANDARDS:
<br />1. ASTM
<br />2. NFPA
<br />B. MATERIALS
<br />1. PRE -SELECTED BY OWNER
<br />2. PATTERNS AS INDICATED IN INTERIOR COLOR SCHEDULE
<br />3. MINIMUM 26 OZ. MATERIAL
<br />4. STATIC DECAY TEST SPECIFICATIONS: NFPA 56 A, METHOD 4046 OF THE
<br />FEDERAL TEST STANDARD 101 B.
<br />5. DOC FF-1 "PILL TEST" (CPSC 16 CFR PART 1630)
<br />A. STANDARDS:
<br />1. ASTM
<br />2. NFPA
<br />B. MATERIALS
<br />1. PRE -SELECTED BY OWNER
<br />2. PAINT MANUFACTURERS & COLOR SELECTION
<br />AS INDICATED ON INTERIOR COLOR SCHEDULE
<br />C. SCHEDULE:
<br />1. EXTERIOR
<br />a.
<br />WOOD AND PLYWOOD: PRIME COAT & 2 GLOSS
<br />FINISH COATS OF HOUSE PAINT, W/EACH COAT
<br />01.5 MILS DFT.
<br />b.
<br />FERROUS & MISCELLANEOUS METALS: METAL PRIMER
<br />® 3 MILS DFT & TWO COATS INDUSTRIAL ENAMEL
<br />B54 SERIES ® 2.0 MILS DFT EACH.
<br />c.
<br />GALVANIZED METAL: ACRYLIC PRIMER & TWO COATS
<br />EXTERIOR FLAT LATEX PAINTO 1.4 MILS DFT, EACH.
<br />2. INTERIOR:
<br />a.
<br />PAINTED WOOD AND PLYWOOD: ONE COAT OF ALKYD
<br />ENAMEL UNDERCOATER 0 2.0 MILS DFT AND TWO
<br />COATS OF OF ALKYD EGG SHELL ENAMEL ® 2.0 MILS DFT.
<br />b.
<br />OPEN GRAINED WOOD AND PLYWOOD STAIN AND VARNISH:
<br />ONE COAT OF INTERIOR WOOD STAIN AND TWO COATS OF
<br />OIL BASE GLOSS VARNISH.
<br />c.
<br />GYPSUM BOARD - EGG SHELL FINISH:
<br />ONE COAT OF PRIMER AND SEALER ® 1.4 MILS DFT AND TWO
<br />COATS OF LATEX EGG SHELL PAINT 0 1.4 MILS DFT.
<br />d.
<br />FERROUS METAL - ALKYD FLAT PAINT: ONE COAT OF METAL
<br />PRIMER ® 3.0 MILS DFT AND TWO COATS SEMI -GLOSS ALKYD
<br />PAINT ® 2.0 MILS DFT.
<br />e.
<br />GALVANIZED METAL - ALKYD FLAT PAINT: ONE COAT GALVITE@ 2.0
<br />MILS DFT AND TWO COATS ALKYD SEMI -GLOSS PAINT ® 2.0 MILS
<br />DFT.
<br />POWER ASSISTED ACCESSIBLE DOOR OPERATION NOT
<br />DOOR FOR VESTIBULE AND/OR WAITING ROOMS:
<br />PROVIDE THE FOLLOWING SWINGING DOOR OPERATOR AND CONTROLS WITH VISUAL
<br />APPLICATION & LOW ENERGY REQUIREMENTS. THE SYSTEM CONSISTS OF
<br />ELECTRO-MECHANICAL SWINGING DOOR OPERATOR AND ELECTRICAL CONTROLS, ALUMINUM
<br />HEADER, CONNECTING HARDWARE. ACTUATING CONTROLS.
<br />GUIDE RAILS AND ON/OFF/HOLD CONTROLS. ALL COMPONENTS SHALL BE FACTORY
<br />ASSEMBLED, ADJUSTED AND TESTED.
<br />THE OPERATOR SHALL OPEN THE DOOR WITH A -6 HP, DC MOTOR/HIGH TORQUE
<br />REDUCTION GEAR SYSTEM, CUT SPIRAL BEVELED GEAR SET WELDED TO A TOOTHED DRIVE
<br />SHAFT AND LINKAGE. THE DRIVE SYSTEM SHALL HAVE POSITIVE, CONSTANT ENGAGEMENT. A
<br />CAM & ROLLER MECHANISM SHALL PROVIDE FOR A NON -BACK -LASH POSITIVE OPEN &
<br />CLOSE POSITIONING. THE OPERATOR SHALL STOP THE DOOR IN THE OPEN POSITION BY
<br />ELECTRICALLY REDUCING THE MOTOR VOLTAGE AND STALLING AGAINST A FIELD ADJUSTABLE
<br />80 TO 135 DEGREE POSITIVE STOP.
<br />THE MICROPROCESSOR CONTROLS SHALL BE FIELD ADJUSTABLE TO
<br />COMPLY W/ ANSI A156.19 LOW ENERGY CODE REQUIREMENTS.
<br />FIELD ADJUSTMENTS FOR DOOR -OPENING SPEED, DOOR -OPENING
<br />FORCE, DOOR CLOSING SPEED, DOOR -CLOSING FORCE SHALL BE
<br />PROVIDED WITHOUT ADDING ADDITIONAL COMPONENTS. THE
<br />OPERATOR SHALL HAVE THE ABILITY TO CONVERT FROM RIGHT HAND
<br />TO LEFT HAND OPERATION WITH SIMPLE FIELD MODIFICATIONS. THE
<br />OPERATOR SHALL BE DESIGNED TO ACCOMMODATE RIGHT HAND,
<br />LEFT HAND, IN -SWING, OUT -SWING, VISIBLE, CONCEALED, LOW
<br />ENERGY AND FULL ENERGY APPLICATIONS WITH MINIMAL FIELD
<br />MODIFICATIONS AND PARTS.
<br />THE OPERATOR SHALL CLOSE THE DOOR BY SPRING ENERGY, THUS
<br />USING THE MOTOR AS A BRAKE TO AIDE THE CLOSING SPEED. THE
<br />CLOSING SPRING SHALL BE A HELICAL COMPRESSION SPRING,
<br />ADJUSTABLE FOR POSITIVE CLOSING ACTION AT A LOW MATERIAL
<br />STRESS LEVEL FOR LONG SPRING LIFE. THE HELICAL COMPRESSION
<br />SPRING SHALL BE EASILY ADJUSTABLE TO ACCOMMODATE A WIDE
<br />RANGE OF CONDITIONS. ALSO A RHEOSTAT MODULE ALLOWS FOR
<br />EASY INDEPENDENT FIELD ADJUSTMENT OF CLOSING AND LATCHING
<br />SPEEDS USING THE MOTOR AS A BRAKE. THE OPERATOR SHALL
<br />PROVIDE A NON -HANDED, EASILY ADJUSTABLE, OPEN STOP TO
<br />PERMIT ADJUSTABLE OPENING ANGLES FROM 80' TO 135' OF
<br />CONSTANT CYCLE UTILIZING CAM & ROLLER. THE OPERATOR SHALL
<br />DELIVER AN EVEN, CONSISTENT OPEN FORCE FROM A FULLY
<br />CLOSED POSITION TO A FULLY OPENED POSITION. FURTHERMORE
<br />THE OPERATOR PROVIDES FOR FULLY CLOSED AND FULLY OPENED
<br />POSITIONS. AUXILIARY SWITCH PERMITS MONITORING THE DOOR
<br />POSITIONING.
<br />THE OPERATOR MAY FUNCTION AS A MANUAL DOOR CLOSER IN THE
<br />DIRECTION OF SWING WITH OR WITHOUT POWER. A CAM AND
<br />ROLLER MECHANISM SHALL ALLOW THE OPERATOR TO DELIVER AN
<br />EVEN, CONSISTENT OPEN FORCE ACROSS THE ENTIRE TRANSITION
<br />FROM DOOR FULLY CLOSED TO DOOR FULLY OPEN.
<br />EMERGENCY RELEASE: FOR CENTER PIVOT DOOR(S) - NORMAL IN
<br />SWING, THE OPERATOR SHALL HAVE A BUILT-IN EMERGENCY
<br />RELEASE WITH CONTROLLED SPRING RETURN TO THE CLOSED
<br />POSITION WITHOUT MANUAL RESETTING. WHILE THE DOOR IS IN THE
<br />EMERGENCY RELEASE MODE, A DISCONNECT SWITCH SHALL PREVENT
<br />POWERED OPERATION. NO HEADER OR JAMB MOUNTED STOPS OR
<br />CAMS SHALL BE REQUIRED FOR EMERGENCY FUNCTION. NOT MORE
<br />THAN 50 POUNDS AT THE LOCK STILE SHALL BE REQUIRED FOR
<br />EMERGENCY USE PER BHMA A156.10.
<br />GENERAL NOTE:
<br />TENANT IMPROVEMENTS WILL
<br />REQUIRE A VARYING AMOUNT OF
<br />IMPROVEMENTS UNDER THIS
<br />PROJECT SCOPE OF WORK.
<br />THEREFORE, SOME OF THESE
<br />SPECIFICATIONS MAY ONLY RELATE
<br />TO A SMALL PORTION OF THE
<br />WORK, OR IN SOME CASES NONE
<br />AT ALL.
<br />C
<br />L
<br />>1
<br />O
<br />O
<br />4-
<br />•1
<br />_D:
<br />L
<br />>
<br />N
<br />-0 �
<br />C
<br />Z
<br />>
<br />c
<br />O
<br />co
<br />O
<br />U
<br />}�
<br />C
<br />•�
<br />to
<br />C
<br />a-•+
<br />f'Y�
<br />•r-I
<br />cz
<br />L.L
<br />U
<br />L.
<br />cA
<br />d
<br />O
<br />O
<br />C
<br />X
<br />^
<br />4-1
<br />O
<br />O
<br />I..V
<br />U
<br />• 1
<br />c0
<br />U)
<br />a)
<br />L
<br />C
<br />L
<br />+�
<br />(1)
<br />O
<br />C
<br />E
<br />4-
<br />O
<br />• 1
<br />a)
<br />U
<br />'O
<br />�c
<br />.grin '1 dra,On im,, i w I;ti &,
<br />>.I by khc i ,aM a o sd _-
<br />°.ri
<br />at4'
<br />1�,
<br />F
<br />U
<br />cli
<br />Q
<br />M
<br />QQ
<br />cil)
<br />C
<br />0
<br />J
<br />F-1
<br />�
<br />O LLu
<br />O
<br />O
<br />r
<br />O �
<br />Lu 00
<br />C'3 I\
<br />N
<br />O
<br />0)
<br />m
<br />CCW
<br />=)
<br />Z
<br />co
<br />Q c'0
<br />cM
<br />^x U
<br />Ln
<br />H
<br />O
<br />H ce)
<br />Q O
<br />(y)
<br />M
<br />_W LO
<br />CV
<br />I --I
<br />m
<br />J I�_
<br />Q h
<br />X
<br />LLLL
<br />Z
<br />O
<br />Q
<br />U
<br />O
<br />J
<br />wLO
<br />T
<br />"
<br />cy)
<br />CIS
<br />U
<br />M
<br />VJ
<br />Z
<br />u
<br />J
<br />Q
<br />Q
<br />~
<br />ZE3
<br />J
<br />>
<br />Q
<br />vJ
<br />W
<br />CE
<br />J
<br />CL
<br />J
<br />W
<br />_
<br />N
<br />Z
<br />E
<br />w
<br />N
<br />DRAWN BY:
<br />LJ/CH
<br />DATE: 03/ 12/ 13
<br />PROJECT NO.1230
<br />REVISIONS
<br />Sheet No.
<br />T-5
<br />
|