5440 Gall Blvd (2) - Laserfiche WebLink

Browse Search

I I DOOR SCHEDULE 2 1 STOREFRONT SCHEDULE: r.iG\ni ci DOOR NUMBER DOOR TYPE FRAME TYPE PROVIDED BY INSTALLED BY SIZE MATERIAL GLAZING JAMB DETAIL HARDWARE REMARKS DO] EX. EX. EX. EX. EX. EX. EX. EX. EX. EXT. ALUMINUM/GLASS STOREFRONT DOOR TO REMAIN D 02 EX. EX. EX. EX. EX. EX. EX. EX. EX. EXT. ALUMINUM/GLASS STOREFRONT DOOR TO REMAIN D 03 EX. EX. EX. EX. EX. EX. EX. EX. EX. EXISTING INTERIOR DOOR TO REMAIN D 04 EX. EX. EX. EX. EX. EX. EX. EX. EX. EXISTING INTERIOR DOOR TO REMAIN D 05 EX. EX. EX. EX. EX. EX. EX. EX. EX. EXT. ALUMINUM/GLASS STOREFRONT DOOR TO REMAIN MARK PROVIDED BY INSTALLED BY SIZE MATERIAL GLAZING REMARKS w— 1 G.C. G.C. GLASS/ALUMINUM TEMPERED/IMPACT WIN[Dow ON NOTE: STOREFRONT CONTRACTOR TO FIELD MEASURE AND VERIFY WINDOW DIMENSIONS PRIOR TO ANY FABRICATION AND INSTALLATION. SIZES PROVIDED ARE APPROXIMATE. HANDICAP ACCESSIBLE GUIDELINES:4.27.4 OPERATION CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5 LBF (22.2 N). 5 KNEE WALL DETAIL 3 1 STOREFRONT NOTES 4 STOREFRONT TYPES STOREFRONT GENERAL NOTES: STONE WALL CAP OR 1. PROVIDE SAFETY GLAZING (TEMPERED) AS REQUIRED BY FLORIDA APPROVED EQUAL BY OWNER BUILDING CODE (FBC) SECTION 2405. 2. CONTRACTOR SHALL PROVIDE FLORIDA PRODUCT APPROVAL SUBMITTALS FOR THE FOLLOWING BUILDING COMPONENTS. 4-12 3-5/8" TOP TRACK 2.1. EXTERIOR HOLLOW METAL DOORS 2.2. STOREFRONT SYSTEMS EXISTING STOREFRONT 3. STOREFRONT ALUMINUM FINISH TO BE CLEAR ANODIZED. TO REMAIN 3-5/8" METAL STUDS 16" O.C. 4. CONTRACTOR TO PROVIDE (3) COPIES FOR REVIEW AND SUBMITTALS TO THE LOCAL JURISDICTION. f- 5/8" GYP BOARD EA. SIDE o MOISTURE RESISTANT FINISHED W/ FRP PANELS 0 CLARKDIETRICH PONY WALL N FINISH BRACING EVERY 48" O.C. FLOOR TYPE W-1(NEW SLIDING WINDOW) 3-5/8" BOTTOM TRACK TAPCON TO EX. CONC. EVERY 12" O.C. F NTERIOR PARTITION WALL TYPE 1 DETAIL 7 INTERIOR PARTITION WALL TYPE 2 DETAIL 8 FRAMING NOTES 9 FLORIDA PRODUCT APPROVAL LIST NOTES: l . FRAMING MATERIALS 1.1. STUDS AND TRACKS: ANSI ASTM C645: GALVANIZED SIZES AND SHAPES AS SHOWN ON THE DRAWINGS. PROVIDE 20 GA. C STUDS (3-5/8") UNLESS NOTED OTHERWISE. 1.2. BACKING: GALVANIZED SHEET METAL, 20 GA. 1.3. FURRING CHANNELS: 20 GA., 7/8" HAT SHAPED FORMED STEEL. STEEL CHANNEL 20 GA. GALV. STEEL CHANNEL 2. GYPSUM BOARD MATERIALS FASTEN 24" O.C. MAX. 2.1. GYPSUM BOARD: ANSI/ASTM C36: FIRE ASSEMBLIES UL RATED: 5/8" THICK, ENDS SQUARE CUT, TAPERED EDGES. D "T I K ND APPROVED PRODUCTS LIST PRODUCT CATEGORY SUB —CATEGORY MANUFACTURER APPROVAL # WINDOW PASS —THROUGH READY ACCESS FL5102.3 2.2. MOISTURE RESISTANT GYPSUM BOAR .ANSI/ASTM C630. 5/8 H C , E S EXTEND WALL TO UNDERSIDE OF SQUARE CUT, TAPERED EDGES. EX. ROOF DECK (OR) INSTALL 2.3. MOISTURE RESISTANT GYPSUM BOARD: ANSI/ASTM C630: 5/8" THICK, ENDS EXTEND WALL TO UNDERSIDE OF KICKERS 5-0" O.C. MAX. SQUARE CUT, TAPERED EDGES. EX. ROOF DECK. NOTE: GWB TO STOP 4'' DROP 3. ACCESSORIES CEILING OR TO UNDERSIDE OF FOR CEILING INFORMATION SEE 3.1. SEALANT: NON -HARDENING PERMANETLY RESILIENT AND NON -SKINNING, FOR ROOF DECK. SEE FLOOR PLAN. RCP USE IN CONJUNCTION WITH GYP BOARD. 3.2. CORNER BEADS: METAL 3.3. JOINT MATERIALS: ANSI/ASTM C475: REINFORCING TAPE, JOINT COMPOUND, ADHESIVE, WATER, FASTENERS. 3.4. TEXTURE MATERIALS: SPRAY APPLIED LIGHT TO MEDIUM FINE TEXTURE. 5/8" GYP. BOARD EA. SIDE. SEE 5/8" GYP. BOARD EA. SIDE. SEE 3.5. FASTENERS: TYPE S SELF TAPPING SCREWS IN SIZE AND SPACING AS REQUIRED FLOOR PLAN. FLOOR PLAN. BY FBC, OR UL RATED SYSTEM, NOTE: GWB TO STOP 4" ABOVE 4. INSTALLATION DROP CEILING U.N.O. 4.1. INSTALL METAL STUDS AND ACCESSORIES IN ACCORDANCE WITH THE MANUFACTURER'S RECOMMENDATION AND RECOMMENDED INDUSTRY PRACTICES. 4.2. ALIGN WALL ASSMEBLIES TO A TOLERANCE OF ONE IN 200 HORIONTALLY AND ONE IN 500 VERTICALLY. 4.3. PROVIDE THREES STUDS AT CORNERS, AND DOUBLE STUDS AT WALL OPENINGS. 4.4. COORDINATE WITH OTHER TRADES FOR PROPER LOCATIONS, SIZES, THICKNESS, AND ATTACHING REQUIREMENTS OF BACKING/BLOCKING. OPTIONAL BLANKET INSULATION OPTIONAL BLANKET INSULATION 4.5. COORDINATE WITH OTHER TRADES PIPES, DUCTS, CONDUITS WHICH ARE TO BE FOR SOUND PROOFING. SEE FOR SOUND PROOFING. SEE CONCEALED WITH WALL ASSEMBLIES. FLOOR PLAN. FLOOR PLAN. 4.6. EDGES OF DOOR IS LOCATED 4" OFF ADJACENT WALL EXCLUSIVE OF FAME. ALL OTHER DOOR OPENINGS ARE LOCATED TO ONE SIDE OF ROUGH OPENING, FRAME EXCLUSIVE. 4.7. GENERAL PLAN DIMENSIONS ARE FROM FINISH WALL SURFACE TO FINISH WALL SURFACE. AT CORRIDORS AND CRITICAL CLEAR DIMENSIONS WHERE 3 %" 20 GA. STEEL STUDS AT 16'' 3 A' 20 GA. STEEL STUDS AT 16" DIMENSIONS IS FROM FACE TO FINISHED GYPSUM BOARD ON SIDE WHERE O.C. (U.N.O.) O.C. (U.N.0.) CLEAR DIMENSION MUST BE HELD. 20 GA. GALV . STEEL CHANNEL 20 GA. GALV . STEEL CHANNEL FASTEN TO SLAB AT 24" O.C. FASTEN TO SLAB AT 24" O.C. EX. FLOOR SLAB CONCRETE FLOOR ENGINEERING & CONSTRUCTION AUSTIN CONSTRUCTION GROUP 2706 STALLONE DRIVE TAMPA, FLORIDA 33605 (813) 293-8883 FLORIDA PE 48917 192169 - CGC1521407 - CUC1224196 - CFC1430334 - FPC15-4000052 PROJECT INFORMATION: CLIENT: R►CHARD KAZBOUR PROJECT NAME: HUNGRY HOWIES RESTAURANT ADDITION PROJECT LOCATION: 5440 GALL BLVD ZEPHYRHILLS, FL 33542 SEAL: GOATS i .....E ��'•. ��i �o-- ,r_ � O ... FL COA NO. 30178 ENGINEER OF RECORD FL LICENSE NO. TO THE BEST OF THE ENGINEER'S KNOWLEDGE, THE PLANS AND SPECIFICATIONS COMPLY WITH THE APPLICABLE MINIMUM BUILDING CODES REVISIONS: NO. DATE COMMENTS SHEET TITLE: DOOR, WINDOW, AND WALL DETAILS SHEET INFORMATION: DRAWN: A.C. SHEET NO. DATE: 7/22/2024 CHECKED: K.C. DATE: 7/22/2024 A201 PROJECT NUMBER: SCALE: INDEX: AS SHOWN 0 w V) Q m c� z