5440 Gall Blvd (2) - Laserfiche WebLink

Browse Search

I I PLUMBING GENERAL NOTES 1 2 1 PLUMBING GENERAL NOTES 1 6 1 PLUMBING SCHEDULE I 1. ALL WORK UNDER THIS DIVISION WITH THE CODES AND STANDARDS AS LISTED ON THE PROJECT DRAWINGS AND TO OTHER PERTINENT CODES MADE A PART OF SUCH CODE BY REFERENCE. 2. TO THE BEST OF THE ENGINEERS KNOWLEDGE, THE PLANS COMPLY WITH THE APPLICABLE MINIMUM BUILDING CODES AND THE APPLICABLE FIRE -SAFETY STANDARDS AS DETERMINED BY THE LOCAL AUTHORITY IN ACCORDANCE WITH SECTION 110.8.4.4 OF THE FLORIDA BUILDING CODE AND 633 FLORIDA STATUES. 3. PLANS INDICATE THE SCHEMATIC LAYOUT AND LOCATION OF THE PLUMBING SYSTEM COMPONENTS. UNLESS SPECIFIC DIMENSIONS ARE NOTED, THE ACTUAL LOCATION OF THESE COMPONENTS SHALL BE DETERMINED IN THE FIELD IN COORDINATION WITH THE WORK OF OTHER TRADES, THE USE OF MANUFACTURER'S SHOP DRAWINGS AND SIMILAR CERTIFIED DATA. PLANS SHALL NOT BE SCALED. 4. NOTIFY THE ENGINEER OR HIS AUTHORIZED REPRESENTATIVE OF ANY DAMAGE TO THE EXISTING INSTALLATION BEFORE PROCEEDING WITH WORK. 24. ALL SANITARY, VENT AND WATER PIPING SHALL BE TESTED BEFORE CONCEALED IN ANY WAY. ALL JOINTS SHALL BE MADE DRIP TIGHT BEFORE BEING CONCEALED. DOMESTIC WATER PIPING SHALL BE TESTED AT 1-1 /2 TIMES OPERATING PRESSURE OR 100 PSI, WHICH EVER IS GREATER. 25. DISINFECT POTABLE WATER SYSTEM PER THE FBC. PROVIDE DOCUMENTATION IN THE CLOSE OUT DOCUMENTS. 26. PIPING TO THE INLET OF A WATER HEATER AND PIPING CONVEYING WATER HEATED BY A WATER HEATER SHALL BE INSULATED IN ACCORDANCE WITH SECTION C404.4 OF THE FLORIDA BUILDING CODE, ENERGY CONSERVATION. 1 3 1 CODE CRITERIA 5. WHERE THE CEILING SPACE IS USED AS A RETURN AIR PLENUM, ALL PLUMBING WORK IN THAT SPACE SHALL COMPLY WITH THE REQUIREMENTS OF NFPA-70 (NED) AS IT NOTE: RELATES TO THAT APPLICATION. THE USE OF PVC WITHIN THE PLENUM IS STRICTLY ALL CODES SHALL COMPLY WITH THE FLORIDA STATUES 69A-3.012 AND THE STATE FIRE PROHIBITED. COORDINATE WITH OTHER INSTALLERS TO PREVENT THE INSTALLATION MARSHALL'S RULE. THIS LIST IS NOT INCLUSIVE OF ALL CODES AND STANDARDS THAT OF PROHIBITED MATERIALS. MAY OR MAY NOT APPLY TO THIS PROJECT. 6. SUBMIT SHOP DRAWINGS OF ALL FIXTURES AND MATERIALS FOR REVIEW BY OWNER. INSTALL AND TEST ALL REQUIREMENT AND MATERIALS IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS. SUBMIT DRAWINGS AND CUT SHEETS FOR ALL PRODUCTS ALL AT ONE TIME. INDEX ALL ITEMS TO THE PROJECT MANUAL OR DRAWINGS AS APPLICABLE. SHOP DRAWINGS THAT DEVIATE FROM THE REQUIREMENTS OF THE CONTRACT DOCUMENTS SHALL LIST ALL DIFFERENCES IN A COVER LETTER ATTACHED TO TOP OF T5HE SUBMITTAL. 7. PIPING AND OTHER ITEMS OF THE PLUMBING SYSTEM SHALL BE SUPPORTED DIRECTLY FROM THE BUILDING STRUCTURE AND NOT FROM THE CEILING, CEILING SUSPENSION SYSTEM, DUCTWORK, PIPING, OR ELECTRICAL SYSTEMS. 8. HANGERS, ANCHORS AND SUPPORTS SHALL SUPPORT THE PIPING AND CONTENTS OF THE PIPING HANGERS AND STRAFING MATERIALS SHALL BE OF APPROVED MATERIALS THAT WILL NOT PROMOTE GALVANIC ACTIONS. PROVIDE PIPE SADDLES BELOW INSULATED PIPES. 9. HANGERS AND ANCHORS SHALL BE ATTACHED TO THE BUILDING CONSTRUCTION IN AN APPROVED MANNER. 10. PROVIDE ALL OFFSETS AND FITTINGS REQUIRED FOR A FULLY FUNCTIONAL SYSTEM. MAKE CONNECTION TO SITE UTILITIES. COORDINATE WITH SITE UTILITY CONTRACTOR AS REQUIRED. 11. CONCEAL PIPING ABOVE CEILING, WITHIN WALL OR CHASES OR AS SPECIFICALLY NOTED. 12. ALL EXPOSED PIPE AND FITTINGS IN FINISHED AREAS SHALL BE CHROME PLATED. IF PIPING IS NOT AVAILABLE CHROME PLATED, PIPING SHALL BE PAINTED WITH CHROME COLORED PAINT. 13. COORDINATE PIPING WITH ALL ELECTRICAL EQUIPMENT (PANELS, TRANSFORMERS, ECT.) PRIOR TO ANY INSTALLATION. DO NOT ROUTE ANY PIPING OVER ANY ELECTRICAL DEVICES. 14. ALL WALL MOUNTED LAVATORIES SHALL BE ATTACHED TO FLOOR MOUNTED CARRIERS. 15. PRIOR TO ANY EXCAVATION OR DEMOLITION, THE CONTRACTOR SHALL COORDINATE HIS WORK WITH OTHER TRADES. 16. THE LOCATIONS OF ALL CLEANOUTS, VALVES, GAUGES, ECT. SHALL BE LOCATED FOR ACCESS AND/OR SERVICE IN REFERENCE TO THE FINISHED BUILDING. REFER TO THE DRAWINGS FOR APPLICABLE DETAILS. WALL CLEANOUT SHALL BE 18" A.F.F. 17. REFER TO ARCHITECTURAL DRAWINGS FOR EXACT LOCATION AND ROUGHING DIMENSIONS OF ALL PLUMBING FIXTURES, DRAINS, ECT. 18. DIELECTRIC UNIONS SHALL BE INSTALLED AT ALL CONNECTIONS OR DISSIMILAR METALS (SUCH AS COPPER TO GALVANIZED STEEL,) 19. WASTE AND SOIL PIPING SHALL BE PVC TYPE DWV AND SHALL CONFORM TO ONE OF THE FOLLOWING STANDARDS: ASTM D 2665, ASTM D 2949 OR CSA B181.2. FITING SHALL BE PVC AND SHALL CONFORM TO ONE OF THE FOLLOWING STANDARDS: ASTM D 2665, ASTM D 3311 OR ASTM F 1866. JOINTS SHALL BE SOLVENT CEMENTING. A PURPLE PRIMER THAT CONFORMS TO ASTM F 656 SHALL BE APPLIED TO JOINT SURFACES (CLEAN AND FREE FROM MOISTURE). SOLVENT CEMENT NOT PURPLE IN COLOR AND COFMING TO ASTM D 2564 OR CSA B137.3 SHALL BE APPLIED TO ALL JOINT SURFACES. JOINTS SHALL BE IN ACCORDANCE WITH ASTM D 2855. SLOPE ALL SANITARY PIPING 3" TO 6" AT A MINIMUM SLOPE OF g' PER FOOT 20. HOT AND COLD WATER PIPING SHALL BE CPVC AND SHALL CONFORM TO NSF 61 AND ONE OF THE FOLLOWING STANDARDS, ASTM B 75, ASTM B 88, ASTM B 251, OR ASTM B 447. FITTINGS SHALL BE COPPER OR COPPER ALLOY AND SHALL CONFORM TO NSF 61 AND ONE OF THE FOLLOWING STANDARDS ASME B16.15, ASME B16.18, ASME B16.23, ASME B16.23, ASME B16.26 OR ASME B16.29. SOLDERED JOINTS SHALL BE MADE IN ACCORDANCE WITH THE METHODS OF ASTM B828. THE JOINING OF WATER SUPPLY SHALL BE 95 LEAD FREE SOLDER AND THE SOLDER SHALL CONFORM TO ASTM B 32. 21. PROVIDE VALVES WHERE INDICATED ON PLAN AND NECESSARY FOR PROPER SYSTEM OPERATION AND COMPONENT ISOLATION. PROVIDE VALVES RATED FOR 125 PSI OR GREATER WORKING PRESSURE IN WATER PIPING. PROVIDE LEAD FREE BRONZE VALVES. BALL VALVES SHALL BE TWO-PIECE BODY, FULL PORT, WITH STAINLESS STEEL BALL. 22. SLOPE ALL SANITARY PIPING 3" TO 6" AT A MIN. SLOPE OF 1 /8" PER FOOT. ALL SANITARY PIPING 2-1/2" AND SMALLER SHALL BE SLOPED AT A MIN. OF 1 /4" PER FOOT. 23. ALL EXPOSED PIPING UNDER ACCESSIBLE LAVATORIES SHALL BE INSULATED WITH PROTECTIVE UNDER -SINK PIPE COVER AND PLUMBING ENCLOSURES AS MANUFACTURE SPECIFICATIONS. - FLORIDA BUILDING CODE (FBC), EIGHTH EDITION (2023) - ALL SECTIONS - FLORIDA BUILDING CODE (FBC), EIGHTH EDITION (2023) - PLUMBING - FLORIDA FIRE PREVENTION CODE 2023 NATIONAL FIRE PROTECTION ASSOCIATION (NFPA): - NFPA-70 (2020) NATIONAL ELECTRICAL CODE NFPA-72 (2019) NATIONAL FIRE ALARM CODE - NFPA-90A (2021) STANDARD FOR THE INSTALLATION OF AIR-CONDITIONING AND VENTILATING SYSTEMS NFPA-90B (2021) STANDARD FOR THE INSTALLATION OF WARM AIR HEATING AND AIR CONDITION SYSTEMS AMERICAN SOCIETY OF HEATING, REFRIGERATION AND AIR CONDITIONING ENGINEERS, INC (ASHRAE): - ASHRAE GUIDELINES 4-2019 - PREPARATION OF OPERATING AND MAINTENANCE DOCUMENTATION FOR BUILDING SYSTEMS - ASHRAE STANDARD 62.1-2019 AND APPROVED ADDENDA - VENTILATION FOR ACCEPTABLE INDOOR AIR QUALITY - ASHRAE STANDARD 126-2020 - METHOD OF TESTING HVAC AIR DUCTS - ASHRAE STANDARD 180-2018 -STANDARD PRACTICE FOR INSPECTION AND MAINTENANCE OF COMMERCIAL BUILDING HVAC SYSTEMS 4 1 ABBREVIATIONS SYMBOL DESCRIPTION AFF ABOVE FINISHED FLOOR CFM CUBIC FEET PER MINUTE CO CLEAN OUT BLDG BUILDING DIA DIAMETER ELEV ELEVATION EQUIP EQUIPMENT GPM GALLON PER MINUTE PVC POLYVINYL CHLORIDE PIPE FLEX FLEXIBLE GALV GALVANIZED VTR VENT THRU ROOF 5 1 PLUMBING LEGEND & SYMBOLS H W H W H W H W n COLD WATER (CPVC) HOT WATER (CPVC) SANITARY SOIL & WASTE (PVC) SANITARY SOIL & VENT (PVC) GAS LINE (BLACK IRON) PIPE DROP PIPE RISE HANGER SPACING MAXIMUM HORIZONTAL MAXIMUM HORIZONTAL PIPING MATERIAL SPACING (FEET) SPACING (FEET) COPPER OR COPPER -ALLOY TUBING 1-1/4" DIAMETER 6 10 AND SMALLER COPPER OR COPPER -ALLOY TUBING 1-1/2" DIAMETER 10 10 AND LARGER PVC PIPE 4 10 PLUMBING SCHEDULE MARK QTY ORDER BY SUPPLIED BY INSTALL BY DESCRIPTION MANUFACTURER MODEL # FAUCET WATER SUPPLY DRAIN COMMENTS P1 2 OWNER OWNER G.C. HAND SINK ATOSA USA, INC. MRS-HS-18(W) (OR EQUAL) INCLUDED 2' HOT AND COLD 2" INSTALL PER MANUFACTURER P2 1 OWNER OWNER G.C. THREE (3) COMPARTMENT SINK ATOSA USA, INC. MRSB-3-D (OR EQUAL) T&S 5PR-8W 12 2' HOT AND COLD 2" INSTALL PER MANUFACTURER P3 1 OWNER OWNER G.C. COMPARTMENT (1) SINK ATOSA USA, INC. MRSA-11 (OR EQUAL) T&S 5PR-8W12 2' HOT AND COLD 2" INSTALL PER MANUFACTURER P4 1 EX. EX. EX. GREASE TRAP EXISTING EXISTING - - - EXISTING +/- 1,000 GALLON CONCRETE TANK OUTSIDE OF BLDG. P5 1 EX. EX. EX. WATER HEATER EXISTING EXISTING - EXISTING - EXISTING GAS WATER HEATER OUTSIDE OF BLDG. P6 1 EX. EX. EX. MOP SINK EXISTING EXISTING - EXISTING EX. EXISTING MOP SINK TO BE UTILIZED P7 1 G.C. G.C. G.C. MOP SINK PROFLO PFMB2424 (OR EQUAL) PF1 119 HOT AND COLD 3" INSTALL PER MANUFACTURER F.S. 2 G.C. G.C. G.C. FLOOR SINK ZURN FD2376-NH3-H (OR EQUAL) - - 3" 12"X12" FLOOR SINK FOR 3 COMPARTMENT SINK F.D. 2 G.C. G.C. G.C. FLOOR DRAIN ZURN ZN415-2NL-5B-P (OR EQUAL) - - 3" 3" PUSH ON FLOOR DRAIN AM �® fiff AV ENGINEERING & CONSTRUCTION AUSTIN CONSTRUCTION GROUP 2706 STALLONE DRIVE TAMPA, FLORIDA 33605 (813) 293-8883 FLORIDA PE 48917 192169 - CGC1521407 - CUC1224196 - C F C 1430334 - F P C 15-4000052 PROJECT INFORMATION: CLIENT: RICHARD KAZBOUR PROJECT NAME: HUNGRY HOWIES RESTAURANT ADDITION PROJECT LOCATION: 5440 GALL BLVD ZEPHYRHILLS, FL 33542 SEAL: ```�1� i 1l I I I►I //4 Go ATS �� E ••.. �� .` •.• NS .�co.• •. �� :. • -- FL COA NO. 30178 ENGINEER OF RECORD FL LICENSE NO. TO THE BEST OF THE ENGINEER'S KNOWLEDGE, THE PLANS AND SPECIFICATIONS COMPLY WITH THE APPLICABLE MINIMUM BUILDING CODES REVISIONS: NO. DATE COMMENTS SHEET TITLE: PLUMBING NOTES & SCHEDULE SHEET INFORMATION: DRAWN: A.C. SHEET NO. DATE: 7/22/2024 CHECKED: K.C. DATE: 7/22/2024 Po . 1 PROJECT NUMBER: SCALE: INDEX: AS SHOWN