Laserfiche WebLink
3 <br />a <br />00 <br />0 <br />LO <br />Lo <br />a� <br />`v <br />c <br />0 <br />LO <br />O <br />0 <br />J <br />Q7 <br />N <br />O <br />I <br />Q <br />00 <br />0 <br />Ln <br />v <br />cnCr <br />0 <br />0 <br />M <br />0 <br />0 <br />M <br />O <br />I <br />A <br />Ln <br />L0 <br />L <br />v <br />cn� <br />0 <br />.a <br />rn <br />cV <br />0 <br />i <br />CL <br />N <br />E <br />0 <br />x <br />L <br />v <br />C <br />J <br />N <br />t� <br />V <br />c <br />v <br />i <br />y <br />U <br />i <br />U <br />i <br />L> <br />L <br />y <br />I <br />0 <br />i <br />c <br />0 <br />-V <br />J <br />N <br />r� <br />N <br />0 <br />0 <br />O <br />a <br />N <br />N <br />O <br />N <br />N <br />v <br />0 <br />cn <br />m <br />v <br />cn <br />M• <br />1" x 4" SMOOTH <br />TEXTURED <br />TRIM / BAND — <br />FASCIA (TYP) - <br />N <br />r` <br />d' <br />ti <br />COMPOSITION SHINGLES <br />ROOF INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />r-1N <br />00 <br />M• <br />N <br />ti <br />12 <br />5� <br />12 <br />5� <br />12 <br />�5 <br />FRONT ELEVATION - Al <br />12 <br />�5 <br />SCALE: 1 /4"=V-0" <br />1IT-0" RIDGE VENT <br />COMPOSITION SHINGLES <br />ROOF INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - <br />it <br />1'-0" <br />CJ 25 SH CJ CJ HEEL <br />?nd FIN. FLR. <br />T.O.M. 12------------ — r <br />5 CJ /WEEP M-0 <br />HDR HGT. _ _401 <br />RAM <br />F.FL.-----1-------------------- ----- ---� ---- F.FL. <br />LEFT ELEVATION - Al <br />PRE -ENGINEER TRUSS <br />REFER TO STRUCTURAL — <br />PLANS FOR BEAM SIZE <br />2"X4" TYP. <br />5/8" TEXTURED OVER - <br />MTL. LATH & 7/16" OSB <br />SHEATHING & FRAMING <br />AS REQ. <br />REFER TO STRUCTURAL <br />PLANS FOR POST SIZE <br />2x FRAMING AS REQ. <br />POST TO CMU <br />CONNECTOR - REFER TO <br />STRUCTURALPLANS <br />(1) 2"X4" TYP. <br />(2) 2"X6" TYP. —� <br />SEE FOUNDATION PLANS <br />FOR FOOTER SIZE <br />(: ) C-11 <br />OLUMN DETAIL <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-V crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />I;L:&TK•1-*1VZ1WAl <br />-, <br />ca <br />c <br />ra <br />/I <br />r <br />i3 <br />r <br />0 <br />ys <br />4 <br />N <br />N <br />0 <br />N <br />C), <br />N <br />O <br />a <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />W <br />LO <br />W <br />a <br />v E o <br />o <br />O coM U N W <br />p � <br />V <br />N O N to LJL <br />E:to <br />Q <br />'s Lo W u) Sk LLJ w <br />U: <br />Q <br />co N r- -2 LL w a_ <br />� m v� a 1 <br />13 <br />0 <br />__1 LL LL I d LU L <br />mo <br />Z <br />_ hoc <br />roc 05 <br />�—° o o F w <br />5 N co LL O <br />W��°jO' <br />M _1_1 <br />¢ a <br />Z <br />IL LL <br />d a <br />O <br />Z <br />Z 0r u) <br />N M <br />OU Urn <br />Z <br />❑�❑ <br />V M � <br />Z N M <br />o g <br />Z <br />N <br />z o � <br />� <br />Q <br />J <br />V) <br />— N <br />M <br />z <br />IO^ <br />v ' <br />W p <br />Ly N <br />o <br />W � <br />�o <br />r <br />L <br />L Qj <br />Q <br />o <br />r• <br />N <br />g� <br />r� <br />o <br />� <br />� <br />w <br />cO <br />M <br />N <br />zo <br />z <br />z <br />n. E <br />00 <br />�� <br />E O <br />"'z <br />oa <br />t— <br />%O <br />¢¢ <br />000 <br />o <br />0 <br />O E <br />N <br />ff ¢ z <br />o <br />¢ <br />W z <br />aw <br />L <br />ro <br />�o <br />N <br />J <br />h m <br />�m <br />'z <br />am <br />ZZ <br />3o <br />MEN <br />IBM <br />U <br />ao <br />k <br />O <br />w <br />wa <br />=6 <br />-O <br />co1% <br />03 <br />.� pLo <br />J <br />LO <br />m <br />E <br />QLO <br />cA <br />r / <br />(0 <br />O <br />M <br />Cr O <br />O <br />Y <br />TM <br />U <br />O <br />W <br />m <br />1 <br />}J <br />'P_J <br />/r\ <br />�I <br />0) <br />0 <br />(N <br />d <br />LO <br />O <br />Q <br />t <br />co <br />ui <br />m <br />w <br />S U-) <br />N <br />rri N <br />o <br />Z <br />Z <br />E <br />Co <br />a <br />E <br />U J <br />Q Q <br />J <br />JOB <br />NO: <br />22-02397 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.1 <br />