Laserfiche WebLink
1 1111 111 11 <br />3 <br />a <br />co <br />0 <br />Lo <br />v <br />P <br />0 <br />0 <br />r� <br />0 <br />0 <br />J <br />O <br />i <br />Q <br />00 <br />0 <br />N'J <br />Cr <br />U) <br />39 <br />0 <br />a <br />0 <br />0 <br />0 <br />J <br />M <br />O <br />I <br />v <br />C <br />Cr <br />a <br />rn <br />o` <br />a <br />CV <br />0 <br />i <br />CL <br />ayi <br />S^E <br />1 <br />c <br />a <br />/ <br />t7 <br />O <br />E <br />c <br />U <br />y <br />a <br />i <br />U <br />Z <br />00 <br />I <br />i <br />C <br />UO <br />O <br />J <br />t7 <br />N <br />M <br />C <br />N <br />hi <br />a <br />0 <br />a <br />N <br />O <br />N <br />cn <br />0 <br />N <br />Q <br />m <br />0 <br />Lolco <br />I <br />f <br />FASCIA <br />(TYP) <br />12 <br />5� <br />12 <br />�5 <br />COMPOSITION SHINGLES <br />ROOF INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />REAR ELEVATION - Al <br />SCALE: 1 /4"= V-0" <br />RIGHT ELEVATION - Al <br />N <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4%1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (e)cwithin 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />-.O <br />o _ <br />� r <br />r ,} <br />`0 <br />8 ? f I C-- f <br />" r — <br />s. UCa , ' <br />cry OUJ <br />�;�CLy. <br />N <br />N <br />0 <br />N <br />CV <br />CV <br />O <br />:. - <br />- <br />4y. <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineers signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineers signature and seal. <br />N � <br />r <br />c, n <br />As <br />Q O <br />p N N W J <br />N m � � LL <br />� <br />OUJ y 1 <br />.5 co N # LL W <br />Q Qj m y LL a' Y <br />_j a = Q <br />-6— = <br />0 (� ui <br />C. <br />— Z Y <br />a_/ - cD C) <br />LU <br />5 '� N (O m O J <br />W <br />W <br />d <br />-0 a <br />z L0 c" Z cn 0 <br />IL <br />z N o< �3� <br />W ❑oo <br />U <br />z N o <br />o <br />Z � N <br />o <br />J — <br />d � <br />N <br />M <br />(n <br />Nn, 'Z'nn �O <br />O <br />W V <br />IL <br />1�'� • <br />Cn <br />° <br />U <br />O <br />w o <br />Ln <br />to � <br />U <br />w <br />— Emap <br />! <br />= w o <br />¢ <br />�m <br />r` <br />o <br />Mw <br />w <br />C7 <br />o <br />Z <br />G <br />� <br />c6 E <br />E S <br />o <br />�® <br />ZO <br />(6 <br />F— <br />— E <br />O <br /><� <br />�0 � <br />XU <br />°o <br />a z <br />¢ <br />wm <br />UO <br />�U <br />o Q <br />a Z <br />W <br />o <br />¢ <br />L <br />no <br />Cn CZ <br />c <br />O <br />y <br />m <br />0 <br />o <br />Z, <br />Z <br />_ <br />v <br />S <br />< <br />az <br />zz <br />zo <br />< <br />� <br />U <br />a <br />U <br />K <br />o <br />J z <br />w< <br />-o <br />co <br />lol¢ <br />° 3 <br />Lo <br />J <br />LO <br />m <br />M <br />Qom^'' <br />CL <br />L <br />LO <br />G <br />:0CT O <br />O <br />Y <br />r <br />U <br />o <br />(0 <br />\1! <br />QI <br />0 <br />Lr) <br />N <br />00 <br />/n`� <br />p <br />LO <br />Cy') <br />Q <br />r <br />cN <br />ro <br />m <br />CN <br />m iri N <br />o <br />Z <br />Z <br />E <br />f° <br />a <br />E <br />U � ¢ p <br />JOB <br />NO : 22-02397 <br />SCALE : AS NOTED <br />SHEET NO. <br />3.2 <br />