6042 N Gall Bllvd - Laserfiche WebLink

Browse Search

LIGHTING FIXTURES MANUAL SWITCH (if shown on drawings) LOW VOLTAGE CABLE MOTES: 1. REFER TO LIGHTING PLAN FOR OCCUPANCY SENSOR LOCATIONS AND QUANTITIES. OCCUPANCY SENSOR CONTROL DETAIL LIGHTING FIXTURE SCHEDULE NOTES: 1. ORDER LED EXIT SIGNS WITH LETTER COLORS THAT COMPLY WITH LOCAL CODES FROM SECURITY LIGHTING. FOR RED LETTERS USE #PRB (UNIVERSAL) FOR GREEN LETTERS USE #PGB (UNIVERSAL) OR IF THE ABOVE EXIT SIGNS DO NOT COMPLY WITH LOCAL CODES USE, LED SIGN WITH BATTERY BACKUP, LETTER SIZE, COLOR, TYPE AND DIRECTIONAL ARROWS AS REQUIRED BY THE LOCAL AUTHORITIES. 2. BEFORE ORDERING VERIFY WITH LOCAL MUNICIPALITY THAT THIS FIXTURE COMPLIES WITH ANY LOCAL LIGHTING ORDINANCE. EMERGENCY LIGHTING NOTES: CONNECT ALL EXIT SIGNS, EMERGENCY LIGHTS, INVERTER AND NIGHT LIGHTS TO THE EXISTING EXIT/EMERGENCY LIGHTING CIRCUIT. 2. CONNECT ALL EXIT SIGNS, EMERGENCY LIGHTS AND NIGHT LIGHTS TO ONE CIRCUIT BREAKER. 3. LIGHTING INDICATED WITH A "NL" ARE NIGHTLIGHTS AND SHALL BE CONNECTED TO THE UNSWITCHED LEG OF THE CIRCUIT. 4. EMERGENCY LIGHTING HAS BEEN DESIGNED PER NFPA 101 MAINTAIN 1 FC IN PATH OF EGRESS. IF FIELD CONDITIONS REQUIRE ANY CHANGES TO LIGHTING DESIGN, EMERGENCY LIGHTING, SHALL BE INSTALLED TO MEET THE ABOVE REQUIREMENTS. LIGHTING FIXTURE SCHEDULE SYMBOL DESCRIPTION MANUFACTURES CAT. NO. VOLTAGE LAMPS MOUNTING A LED DOWN RADIUS WALL SCONCE - SILVER FINISH SECURITY LIGHTING SYSTEMS NO.: RWSC-36LED-5K-DO-U-PS 120 14W WALL MOUNT E WALL WASHER SECURITY LIGHTING SYSTEMS NO.: RDA-00LM30-NF-S/RDA-60-H 120 16 CEILING RECESSED SEE LIGHTING FIXTURE SCHEDULE NOTE NO.2 LED CAN LIGHT SECURITY LIGHTING SYSTEMS NO.: 12W CEILING RECESSED F BLUE ROUND PENDANT SECURITY LIGHTING SYSTEMS NO.: 12 PENDANT HUNG B 0 RDA-136LM-30-FL-S/RDA-136-H 120 7652 BLE-EQL-306-45358-1-LED 120 REFER TO DECOR DRAWINGS FOR EXACT FIXTURE TYPE LED CAN LIGHT FED FROM SECURITY LIGHTING SYSTEMS NO.: 12W CEILING RECESSED G SLIM PENDANT GREY LARGE SECURITY LIGHTING SYSTEMS NO.: 20 CEILING RECESSED BE O UNSWITCHED INVERTER PANEL FOR USE AS NIGHT LIGHT AND RDA-136LM-30-FL-S/RDA-136-H 120 6797-BPS-1388-71 REFER TO DECOR DRAWINGS FOR EXACT FIXTURE 120 NL EMERGENCY LIGHT. TYPE 2x4, LED LAY -IN PRISMATIC SECURITY LIGHTING SYSTEMS NO.: 44W CEILING LAY -IN C ACRYLIC LENS LCAT24-35HLG-EDU-WP-GK 120 COMBO WITH BATTERY BACK-UP 120 UNIT 20, LED LAY -IN PRISMATIC ACRYLIC SECURITY LIGHTING SYSTEMS NO.: 44W CEILING LAY -IN EMERGENCY BATTERY AND DUAL LITE 2-5W SURFACE TO WALL CE LENS FED FROM UNSWITCHED LCAT24-35HLG-EDU-WP-GK 120 X 2 REMOTE HEAD EV4D-02L-0/EVODB 120 OR SOFFIT INVERTER PANEL FOR USE AS NIGH WHEN CONNECTED TO TWO REMOTE HEADS NL LIGHT AND EMERGENCY LIGHT. (I= (FOR SINGLE GANG JUNCTION BOX) DELIVERY POD LED LIGHT SECURITY LIGHTING SYSTEMS NO.: 9W CEILING RECESSED DENOTES EXISTING DEVICE TO DP 0 LB4-6LD-30K-9-GD/IBX4QL-120 120 EX REMAIN (PROVIDED WITH DELIVERY POD) D 2 HEAD DOUBLE GIMBALL SECURITY LIGHTING SYSTEMS NO.: 14 CEILING RECESSED CEILING -MOUNTED LIGHTING INVERTER WITH MAINTENANCE FREE SEALED (MULTIPLE 25 DEGREE) GM2-120-LM-30-SBS 120 O LEAD CALCIUM BATTERY. Co REFER TO DECOR DRAWINGS FOR EXACT FIXTURE SECURITY LIGHTING SYSTEMS LG1 SERIES TYPE INVERTER MAXIMUM OF FOUR 12.5 WATT CAN LIGHTS PER INVERTER DE 2 HEAD DOUBLE GIMBALL FED FROM SECURITY LIGHTING SYSTEMS NO.: 14 CEILING RECESSED m UNSWITCHED LIGHTING CIRCUIT GM2-120-LM-30-SBS 120 FOR USE AS NIGHT LIGHT AND REFER TO DECOR DRAWINGS FOR EXACT FIXTURE NL EMERGENCY LIGHT TYPE u REVIEW DATE: CITY OF ZEPHY__&__' µ_ RHILLS BUILDING OFFICIAL___ GENERAL NOTES EC SHALL FIELD VERIFY THAT ALL LIGHT FIXTURES SHOWN ON THIS PLAN DO NOT OBSTRUCT OR CONFLICT WITH THE WORK OF OTHER TRADES. IF A DISCREPANCY IS FOUND, THE EC SHALL IMMEDIATELY NOTIFY THE GC BEFORE THE INSTALLATION OF SUCH FIXTURE(S).. IF PC-POS CASH REGISTER SYSTEM IS INSTALLED, RELOCATE FIXTURES ABOVE FRONT COUNTER TO AVOID GLARE ON THE CASH REGISTER SCREENS. INSTALL CABLE WHIP TO FIXTURES SO THAT FIXTURE CAN BE RELOCATED FOUR FEET WITHOUT DISCONNECTING CABLE WHIP. 3. THE USE OF "MC" CABLE WHERE PERMITTED BY LOCAL CODES WILL BE ALLOWED FOR ALL WIRING TO THE LIGHT FIXTURES. "ROMEX" & "BX" ARE NOT ACCEPTABLE. 4. LIGHTING FIXTURES AND LAMPS HAVE BEEN CHOSEN TO ACHIEVE MAXIMUM ENERGY CONSERVATION WHILE MAINTAINING ADEQUATE LEVELS OF ILLUMINATION. LAMP SPECIFICATIONS MUST BE STRICTLY FOLLOWED. ANY DEVIATION FROM LAMP SPECIFICATIONS MUST BE APPROVED IN WRITING BY McDONALD'S CORPORATION. 5. ALL BRANCH CIRCUIT WIRING TO 120 VOLT LIGHTING FIXTURES AND RECEPTACLES SHALL BE AS FOLLOWS. MAXIMUM LENGTH 85FT. - 2 #12, 1 #12 E.G. MAXIMUM LENGTH 140FT. .2 #10, 1 #10 E.G. MAXIMUM LENGTH 225FT. - 2 #8, 1 #8 E.G. MAXIMUM LENGTH 350FT. - 2 #6, 1 #6 E.G. 6. ALL EXTERIOR J-BOXES AND RECEPTACLES SHOWN ON THIS PLAN SHALL BE WATERPROOF. IF SIGNAGE DOES NOT COME WITH DISCONNECT SWITCH PROVIDE TOGGLE SWITCH WITH WEATHERPROOF COVER. ORDER ALL LIGHT FIXTURES FROM: SECURITY LIGHTING SYSTEMS, INC. PHONE: 1-800-LIGHT-IT EMAIL: QUOTATIONS�SECURITYLIGHTING.COM NOTE: VERIFY LIGHTING FIXTURE CATALOGUE NUMBERS WITH INTERIOR DESIGNER PRIOR TO ORDERING FIXTURES. 1 WPi 9 J-BOX FOR McDONALDS FASADE SIGN O KEYNOTE -LEGEND._____ Y 1. CONNECT TO EXISTING CUSTOMER SERVICE LIGHTING CIRCUIT SERVING THIS AREA. 2. CONNECT TO EXISTING DINING AREA LIGHTING CIRCUIT SERVING THIS AREA. 3. CONNECT TO THE EXISTING EXIT/EMERGENCY/NIGHT LIGHTING CIRCUIT. 4. EXISTING LIGHTING AND EMERGENCY LIGHTING IN THIS ARE TO REMAIN AS IS. 5. CONNECT TO EXISTING TOILET LIGHTING CIRCUIT THAT WAS MADE SPARE BY DEMOLITION. 6. PROVIDE CEILING MOUNTED ULTRASONIC OCCUPANCY SENSOR IN RESTROOMS (HUBBELL ATU500C). AIM SENSOR IN DIRECTION INDICATED BY ARROW FOR MAXIMUM COVERAGE OF ROOM. REFER TO OCCUPANCY SENSOR DETAIL ON THIS SHEET. ORDER ALL OCCUPANCY SENSORS FROM, SECURITY LIGHTING LIGHTING SYSTEMS, INC. 7. EACH RESTROOM HAS ONE SENSORS THAT CONTROL ALL LIGHTS TOGETHER AT ONCE IN RESPECTIVE RESTROOM. 8. CONNECT TO UNSWITCHED LEG OF THE RESTROOM LIGHTING CIRCUIT TO FEED INVERTER. 9. CONNECT TO EXISTING KITCHEN/SUPPORT AREA LIGHTING CIRCUIT SERVING THIS AREA. 10. CONNECT TO EXISTING PHOTOCELL EXTERIOR SECURITY LIGHTING CIRCUIT. 11. EC SHALL INSTALL AND CONFIGURE REMOTE EMERGENCY LIGHTING AT AL L EGRESS EXTERIOR DOORS FOR MAXIMUM ILLUMINATION AT POINTS OF EGRESS. INS'TALL WP J-BOX WITH IN SOFFIT TO ALLOW A FLUSH INSTALLATION OF ANY EXTERIOR EMERGENCY EGRESS LIGHTING (TYPICAL). 12. CONNECT TO EXISTING EXTERIOR LIGHTING WALL SCONCE CIRCUIT. \ 13. REFER TO ARCHITECTURAL ELEVATIONS FOR HEIGHTS AND LOCATIONS OF WALL SCONCE AND CANOPY DOWNLIGHTS. 14. EXISTING FRONT FASADE SIGN CIRCUIT. LOAD SUMMARY NO ADDITIONAL LOAD ADDED. LOADS ADDED ARE OFFSET BY LOADS REMOVED BY DEMOLITION. mkiI M N O ' a O � L • ay + U' ' w L < � R 9 9 0 0 x a. _ J Ld a O Lv r' THIS ITEM HAS BEEN ELECTRONICALLY SIGNED AND SEALED BY ADAM T. EMERALD �� 180 2.31 POWELL, PE USING A DIGITAL SIGNATURE AND DATE. PRINTED COPIES ENGINEERING I N IM OF THIS DOCUMENT ARE NOT E 1 CONSIDERED SIGNED AND SEALED AND 9942 CURRIE DAVIS DR. STE H., TAMPA, FL 33619 THE SIGNATURE MUST BE VERIFIED ON TEL (813) 995-0300 !jl .0 ANY ELECTRONIC COPIES. WWW.EMERALDMEP.COM EEI PROJECT* 22072M 88jj - --------