6042 N Gall Bllvd - Laserfiche WebLink

Browse Search

I EXISTING PANEL AP4 I E ISTING E ECTRICAL M P, AP1, AP2 D AP3 6-7 I V-7 I i i li i�I I� GENERAL NOTES: 1. ALL WORK SHALL BE IN ACCORDANCE WITH THE 2017 NATIONAL ELECTRICAL CODE AND SHALL ALSO COMPLY WITH ALL APPLICABLE RULES AND REGULATIONS OF LOCAL AND STATE LAWS AND ORDINANCES. 2. CONTRACTOR SHALL MAKE A THOROUGH EXAMINATION OF THE SITE AND THE CONTRACT DOCUMENTS. NO CLAIM FOR EXTRA COMPENSATION WILL BE RECOGNIZED IF DIFFICULTIES ARE ENCOUNTERED WHICH AN EXAMINATION OF SITE CONDITIONS AND CONTRACT DOCUMENTS PRIOR TO EXECUTING CONTRACT WOULD HAVE REVEALED. 3. ELECTRICAL CONTRACTOR SHALL ARRANGE FOR ALL NECESSARY PERMITS, LICENSES, UTILITY COORDINATION AND INSPECTIONS AS REQUIRED BY THE CITY OR UTILITY COMPANY. OWNER WILL PAY FEES. CONTRACTOR IS RESPONSIBLE FOR ALL EQUIPMENT REQUIRED BY UTILITY COMPANY AND SHOULD INCLUDE NECESSARY COSTS IN BID. 4. CONTRACTOR SHALL LEGIBLY MARK-UP A SET OF 24"x36" DRAWINGS TO REFLECT AS -BUILT CONDITIONS AND TURN OVER TO THE ARCHITECT. 5. PANELBOARD MANUFACTURER SHALL PROVIDE ARC -FLASH WARNING LABELES FOR MDP AND ALL BRANCH PANELBOARDS IN ACCORDANCE WITH NEC 110. GROUNDING: 1. THE INTERIOR ELECTRICAL SYSTEMS SHALL BE COMPLETELY AND EFFECTIVELY GROUNDED AS REQUIRED BY NATIONAL ELECTRICAL CODE ALL METALLIC RACEWAYS SHALL BE MECHANICALLY AND ELECTRICALLY SECURE AT ALL JOINTS AND AT ALL BOXES, CABINETS, FITTINGS AND EQUIPMENT. OUTLET BOXES/DEVICES: 1. ALL OUTLET BOXES SHALL BE RIGIDLY MOUNTED AND SHALL BE EQUIPPED WITH SUITABLE SCREW FASTENED COVERS. OPEN KNOCKOUTS OR HOLES IN BOXES SHALL BE PLUGGED WITH SUITABLE BLANKING DEVICE. 2. OUTLET BOXES SHALL BE 4 INCH SQUARE x 2-1/8" DEEP. OUTLET BOXES LOCATED ABOVE THE CEILING SHALL BE LEGIBLY IDENTIFIED WITH BRANCH CIRCUIT NUMBER OF CIRCUIT TERMINATED WITHIN BY MEANS OF BLACK PERMANENT MARKER. SWITCHGEAR: 1. PANELBOARD DIRECTORY CARDS SHALL BE TYPEWRITTEN WITH ACCURATE AND CURRENT INFORMATION BY THE CONTRACTOR AT THE END OF CONSTRUCTION. __..._._ _ . TP AP4-40 I � O s i I j1_.- I] II I i � f i j TP �....._..... 6 6 AP1-13 6 I , 8207.09 E 1 - 215.07 1 E1 ; � E ?I JEW EXISTING I i PANEL LP WIRE/RACEWAY: 1. ALL CONDUCTORS SHALL BE COPPER, CONDUCTOR INSULATION SHALL BE DUAL TYPE THHN/THWN 75°C. (167°F) FOR DRY, DAMP, AND WET LOCATIONS. CONDUCTOR INSULATION WITH SINGLE TYPE MARKING THHN 90°C (194°F) MAY BE USED FOR DRY LOCATIONS ONLY. ALL CONDUCTORS SHALL BE COLOR CODED AS REQUIRED BY NEC AND FURTHER IDENTIFIED AND CODED AS SPECIFIED HEREINAFTER. COLOR CODING SHALL BE BY MEANS OF COLORED INSULATING MATERIAL, COLORED BRAID OR JACKET OVER THE INSULATION OR BY MEANS OF SUITABLE COLORED, PERMANENT, NON -AGING, INSULATING TAPE APPLIED TO CONDUCTORS AT EACH CABINET OR JUNCTION POINT. THE COLOR CODING SHALL BE ACCOMPLISHED AS THE CONDUCTORS ARE INSTALLED. THE FOLLOWING SYSTEMS OF COLOR CODING SHALL BE STRICTLY ADHERED TO: A) GROUND LEADS: GREEN B) 120/208 VOLT UNGROUNDED PHASE WIRES: PHASE A: BLACK PHASE B: RED PHASE C: BLUE NEUTRAL: WHITE THE COLOR CODE ASSIGNED TO EACH PHASE WIRE SHALL BE CONSISTENTLY FOLLOWED THROUGHOUT 2. ALL BRANCH CIRCUIT WIRING TO 120 VOLT LIGHTING FIXTURES AND RECEPTACLES SHALL BE AS FOLLOWS. MAXIMUM LENGTH 85FT. - 2 #12, 1 #12 E.G. MAXIMUM LENGTH 140FT. - 2 #10, 1 #10 E.G. MAXIMUM LENGTH 225FT. - 2 #8, 1 #8 E.G. MAXIMUM LENGTH 350FT. - 2 #6, 1 #6 E.G. 3. UNLESS OTHERWISE NOTED ALL CONDUCTORS SHALL BE RUN IN THIN WALL CONDUIT AND THIN WALL CONDUIT SHALL BE UNDERWRITERS' APPROVED GALVANIZED ELECTRICAL METALLIC TUBING. COUPLINGS AND CONNECTORS SHALL BE STEEL SET -SCREW TYPE, ZINC OR CADMIUM PLATED. MC CABLE MAY BE USED WHERE CONCEALED IN WALLS. 4. ALL RACEWAYS SHALL BE PROPERLY ALIGNED, GROUPED, AND SUPPORTED BY MECHANICAL TYPE 'CADDY CLIPS AT INTERVALS NOT EXCEEDING 8 FEET. 5. ALL RACEWAYS WITH NO. 10 OR 12 AWG PHASE CONDUCTORS FOR RECEPTACLES, LIGHTING FIXTURES AND SIMILAR CIRCUITS SHALL BE PROVIDE WITH A PARITY SIZED GREEN EQUIPMENT GROUND CONDUCTOR. GROUND CONDUCTOR SHALL BE INSTALLED IN ENTIRE RACEWAY SYSTEM INCLUDING WALL SWITCHES AND FLEXIBLE CONDUIT TO LIGHT FIXTURES. EQUIPMENT GROUND CONDUCTOR SIZES FOR CIRCUITS WITH PHASE CONDUCTORS LARGER THAN NO. 12 AWG ARE INDICATED ON DRAWINGS. GROUND CONDUCTORS SHALL BE CONNECTED TO GROUND BUSS IN PANELBOARDS. 6. RACEWAY PENETRATIONS OF FIRE RATED WALLS AND/OR FLOORS SHALL BE SEALED TO MAINTAIN INTEGRITY OF CONSTRUCTION. ALL PRODUCTS, MATERIALS AND METHODS OF INSTALLATION SHALL BE UL APPROVED AND MEET NFPA. 7. ALL ELECTRICAL CONDUITS SHALL BE CONCEALED IN WALLS UNLESS AS -BUILT CONDITIONS PROHIBITS. GC TO NOTIFY ARCH/ACM OF AS -BUILT CONDITIONS. 004.20 E7 1� i I 039.15 E3 041.09 1 E1 j 216.00 E2 ------- 216.00 216.00 E3 213.00 E11 7 R�, , POWER PLAN SCALE: 1/4" = V-0" TP 210.00 E10 �215.00�lEl210 TP TP TP 0 O U o f yWy I W i Nri w r s /mow luj `.� It � .. •.- re f I vsr (3 . B I X8021.11 E1 8181.01 E2 E2 8203.02 E2 ( L El 8205.11 E2 3 E2 8216.00 E2 E2 8216.00 E7) E2 Lm _ 207.09 E 1 207.10 1 E1 - e `g 8025.02 E2 8039.09 E 1 i ram- _ -_ � �"` 1 I � ; �\ � E • 3 009.15 E1 8023.05 E2 8216.00 1 E2- a o 216.00 E2 8023.05 E2 8216.00 E7 > 246. E7 8024.01 E1ju 8217.13 E2 © � 217.00 E`t� - 8215. 8 E1 8219.00 E7 ca 3021.Q1 E2 8215.98 2 -821 E8 W21.98 82 �5 9 E2 7000.12 --- __ I _ ..._10 oil O KEYNOTE LEGEND 1. RACEWAY KIT PROVIDED WITH COUNTER, INSTALLED BY EC. a 2. IF OPTIONAL TABLE TRACKER SYSTEM IS TO BE USED. IF USED, PROVIDE 2 #12 AND 1 #12 GROUND TO AVAILABLE SPARE 20A/1 P BREAKER. CONNECT CIRCUIT TO (3) 5-20R RECEPTACLES, (1) RECEPTACLE FOR MODEM/GATEWAY (TYPICALLY LOCATED BEHIND VALENCE AT 7'-9" AFF), (1) RECEPTACLE FOR LOCATOR CHARGER (TYPICALLY LOCATED IN MANAGERS OFFICE) AND (1) RECEPTACLE FOR MONITOR (TYPICALLY LOCATED AT PICKUP COUNTER). COORDINATE EXACT LOCATION(S) IN THE FIELD. 3. COORDINATE LOCATION AND REQUIREMENTS OF HAPPY MEAL DISPLAY WITH DECOR COMPANY. TIE INTO LIGHTING CIRCUIT SERVING THIS AREA, 2 #12 AND 1 #12 E.G. IN 1/2' CONDUIT. 4. RELOCATED ORDERING KIOSK. COORDINATE EXACT LOCATION AND REQUIREMENTS WITH ARCHITECT AND OWNER PRIOR TO RELOCATIONS. EXTEND CIRCUITRY AND CONDUCTOR AS REQUIRED. VERIFY THAT EACH KIOSK IS POWERED BY A 1 POLE 20 AMP CIRCUIT BREAKER. 5. COORDINATE LOCATION AND REQUIREMENTS OF FUTURE CASH HANDLER WITH O 0 DECOR COMPANY. POWER IS FED FROM ORDERING KIOSK BASE PLATE, IF NOT LOCATED NEXT TO THE WALL. IF LOCATED NEXT TO TO A WALL THEN FEED FROM Q. _ WALL POWER. 6. COORDINATE LOCATION AND REQUIREMENTS OF J-BOX FOR DECOR ELEMENT WITH DECOR DRAWINGS. 2 #12 AND 1 #12 E.G. IN 1/2' CONDUIT. 7. CONNECT TO SPARE 20 AMP - 1 P, 120 VOLT BREAKER. FURNISH AND INSTALL BREAKER IF A SPARE IS NOT AVAILABLE. CONTRACTOR TO FIELD VERIFY CIRCUIT NUMBERS AND EXACT NUMBER OF SPARES AVAILABLE. SEE SHEET E3.0 FOR REQUIREMENTS THIS ITEM HAS BEEN ELECTRONICALLY SIGNED AND SEALED BY ADAM T. _ �� POWELL, PE USING A DIGITAL SIGNATURE AND DATE. PRINTED COPIES ENGINEERING I N r OF THIS DOCUMENT ARE NOT CONSIDERED SIGNED AND SEALED AND I DAVIS E 9942 CURRIDR. STE H., TAMPA, FL 33619 THE SIGNATURE MUST BE VERIFIED ON TEL (gU) ANY ELECTRONIC COPIES. WWW.EMERALDMEP.COM EEI PROJECT* 22072M .J 11 W 0 O m Ld cr 1802.31 E 2. 0