|
H,V.A® . GENERAL NOTES
<br />1. IF, THROUGH ERRORS OR, OMISSIONS THE INTENT OF ARCH,ri-ECT/ENGINEER WITH REGARD
<br />TO ANY DETAIL IS NOT CLEAR, OR CAPABLE OF MORE THAN ONE INTERPRETATION, SUCH
<br />MATTERS WILL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT/ENGINEER IN WRITING
<br />BEFORE THE SUBMISSION OF BIDS, AND THE ARCHITECT/ENGINEER SHALL MAKE
<br />CORRECTIONS EXPLANATIONS OR, CLARIFICATIONS IN WRITING. NO EXTRA CHARGE WILL BE
<br />ALLOWED FOR THE WORK OR MATERIAL WHICH THE ARCHITECT/ENGINEER WILL REQUIRE,
<br />PROVIDED THAT IT COMES WITHIN A REASONABLE INTERPRETATION OF THE DRAWINGS AND
<br />SPECIFICATIONS.
<br />2. THE PLANS AND SPECIFICATIONS ARE INTENDED AS A GENERAL DESCRIPTION OF THE
<br />WORK TO BE PERFORMED. ALL ITEMS NOT SPECIFICALLY MENTIONED OR INDICATED, BUT
<br />NECESSARY FOR THE COMPLETION OF THE INSTALLATION SHALL BE FURNISHED AND
<br />INSTALLED BY THIS CONTRACTOR. THIS CONTRACTOR SHALL THOROUGHLY ACQUAINT
<br />THEMSELVES WITH THE MECHANICAL, ARCHITECTURAL, STRUCTURAL AND ELECTRICAL PLANS
<br />BEFORE SUBMITTING HIS/HER FINAL BID. NO ADDITIONAL COMPENSATION WILL BE
<br />ALLOWED DUE TO THE CONTRACTOR'S FAILURE TO FAMILIARIZE THEMSELVES WITH THE
<br />PLANS.
<br />3. ALL WORK SHALL BE IN ACCORDANCE WITH THE 'FLORIDA MECHANICAL CODE 2007 WITH
<br />2009 SUPPLEMENTS - MECHANICAL! AND ALL LOCAL CODES.
<br />4. REFER TO THE ARCHITECTURAL REFLECTED CEILING PLAN (IF APPLICABLE) FOR THE
<br />EXACT LOCATION OF AIR DISTRIBUTION DEVICES.
<br />5. THE SIZE AND LOCATION OF EQUIPMENT INSTALLED UNDER DIVISION 23 - MECHANICAL
<br />SHALL BE COORDINATED WITH ALL OTHER TRADES.
<br />6. OPERABLE THERMOSTAT PARTS SHALL BE MOUNTED 48" ABOVE FINISHED FLOOR.
<br />THERMOSTATS SHALL BE FURNISHED WITH A TRANSPARENT VANDAL PROOF LOCKING
<br />COVER. VOLTAGE SHALL BE 24 VOLT UNLESS OTHERWISE INDICATED.
<br />7. DISCONNECT SWITCHES REQUIRED FOR THE MECHANICAL EQUIPMENT SHALL BE PROVIDED
<br />BY DIVISION 26 - ELECTRICAL UNLESS INDICATED OTHERWISE ON SCHEDULE.
<br />8. CONTROL WIRING AND HARDWARE TO COMPLETE THE HVAC CONTROL SYSTEM SHALL BE
<br />FURNISHED AND INSTALLED UNDER DIVISION 23 - MECHANICAL INDICATED ON THESE
<br />CONTRACT DOCUMENTS UNLESS OTHERWISE NOTED ON DRAWINGS.
<br />9. DUCTWORK SHALL BE CONSTRUCTED AND INSTALLED IN STRICT ACCORDANCE WITH NFPA
<br />90A AND 90B.
<br />10. DUCT BENDS FROM VERTICAL TO THE HORIZONTAL AND ANGLED TURNS OF DUCTWORK
<br />SHALL HAVE TURNING VANES INSTALLED.
<br />11. DUCT SIZES SHOWN ARE MINIMUM INSIDE DIMENSIONS.
<br />12. AIR-CONDITIONING SUPPLY AND, RETURN AIR DUCTWORK WITHIN ATTIC SPACES SHALL BE
<br />1-1/2" R-6.0 FIBERGLASS DUCT BOARD, CLASS 1 AIR DUCT IN STRICT ACCORDANCE
<br />WITH UL 181. DUCT BOARD SHALL BE475EI OR 800EI AS PRESCRIBED BY SMACNA
<br />DEPENDING ON THE DUCT SIZE.
<br />13. PAINT INSIDE DUCT SURFACE AND PORTIONS OF STRUCTURE AND CEILING ASSEMBLY
<br />VISIBLE THROUGH GRILLES AND REGISTERS WITH FLAT BLACK PAINT.
<br />14. PIPE AND DUCT ROUTING INDICATED IS SCHEMATIC. HVAC CONTRACTOR SHALL PROVIDE
<br />ANY ADDITIONAL OFFSETS AND FITTINGS, INCLUDING BUT NOT LIMITED TO DIVIDED DUCTS
<br />REQUIRED FOR PROPER INSTALLATION AND TO ACCOMMODATE CLEARANCES AND,
<br />CONFLICTS AS ENCOUNTERED IN THE FIELD.
<br />15. FLEXIBLE DUCTWORK SHALL BE: TYPE INL-25 AS MANUFACTURED BY OWENS-CORNING
<br />FIBERGLASS CORP. OR EQUIVALENT, SUPPORTED WITH 1 1/2" SHEET METAL STRAPS AT
<br />5'-0" ON CENTERS.
<br />16. EXHAUST DUCTWORK SHALL BE UNINSULATED GALVANIZED STEEL.
<br />17. EXHAUST FAN DISCHARGE POINTS SHALL BE INSTALLED A MINIMUM OF 10'-O" FROM ALL
<br />FRESH AIR INTAKE POINTS.
<br />18. COORDINATE WITH ALL THE TRADES PRIOR TO PURCHASING OR INSTALLING EQUIPMENT
<br />AND MATERIALS.
<br />19. COORDINATE HVAC SYSTEM DRAWINGS WITH TRUSS MANUFACTURER DURING SHOP
<br />DRAWING REVIEW TO AVOID INTERFERENCE'S BETWEEN MECHANICAL SYSTEMS AND ROOF
<br />STRUCTURE. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL COSTS ASSOCIATED WITH
<br />TRUSS INTERFERENCE'S THAT OCCUR IN THE FIELD DURING CONSTRUCTION. COORDINATE
<br />IN ADVANCE. DUCT SIZES MAY BE REVISED TO FIT TRUSS SYSTEM MAKING CERTAIN THE
<br />EQUIVALENT INSIDE CROSS -SECTIONAL AREA IS NOT DECREASED.
<br />20. CONTROL WIRING AND CONDUIT SHALL COMPLY WITH NEC AND DIV1SION 26
<br />SPECIFICATIONS.
<br />21. CONDENSATE DRAIN LINES SHALL BE INSULATED WITH MINIMUM 1/2" THICK ARMAFLEX
<br />OR, EQUIVALENT AND INSTALLED WITH A "P" TRAP AT THE UNIT WITH A MINIMUM
<br />TRAP DEPTH OF 2"
<br />22. LOCATE WALL AND ROOF TERMINATION'S AT THE SAME RELATIVE ELEVATION AND
<br />HORIZONTAL POSITION TO MAINTAIN A UNIFORM APPEARANCE. WHEN IN DOUBT
<br />COORDINATE PLACEMENT WITH ARCHITECT. PRIME, COAT, AND PAINT EXTERIOR
<br />TERMINATION'S TO MATCH BUILDING EXTERIOR COLOR.
<br />23. THE CONTRACTOR SHAM SUBMIT TO THE ARCHITECT A WRITTEN TEST AND BALANCE
<br />REPORT OF THE INSTALLED SYSTEM.
<br />H.V.A.C, SYMBOLS LEGEND
<br />DUCTWORK
<br />SUPPLY AIR DUCT - SECTION DIFFUSER CFM
<br />TYPE CEILING MOUNTED SUPPLY. IF OTHER
<br />1 THAN 4-WAY, ARROWS INDICATE AIR
<br />RETURN AIR DUCT - SECTION A-150 ® FLOW PATTERN.
<br />EXHAUST AIR DUCT - SECTION
<br />SUPPLY DUCT UP THRU ROOF OR 24X12 RECTANGULAR DUCT, FIRST
<br />FIGURE IS HORIZONTAL SIDE SHOWN
<br />ELBOW TURNED UP
<br />92"0 ROUND DUCT, DIAMETER SHOWN
<br />XELBOW TURNED DOWN
<br />TURNING VANES -J MANUAL VOLUME DAMPER
<br />R REFRIGERANT PIPING
<br />STANDARD BRANCH TAKEOFF CD CONDENSATE DRAIN
<br />OT THERMOSTAT.
<br />MANUAL DAMPER ® "HDGI" HYDROGEN GAS DETECTOR.
<br />4-WRY DISCHARGE
<br />SQUARE SUPPLY AIR DIFFUSER
<br />zRETURN AIR REGISTER/GRILLE
<br />zEXHAUST AIR REGISTER/GRILLE
<br />kSIDEWALL REGISTER OR GRILLE
<br />CEILING DIFFUSER WITH FLEXIBLE
<br />DUCT SPIN IN FITTING - SIDE DUCT
<br />CONNECTION
<br />150 CFM 200 CFM 230 CFM
<br />TOTAL OUTSIDE AIR = 580 CFM
<br />TOTAL EXHAUST AIR = 350 CFM
<br />BALANCE = POSITIVE PRESSURE BY 230 CFM
<br />1 ;zIlk
<br />11y.
<br />1 i
<br />350
<br />SPLIT SYSTEM AIR CONDITIONING UNIT SCHEDULE�
<br />MARK
<br />AHU-1/CU-1
<br />AHU-2/CU-2
<br />AHU-3/CU-3
<br />AHU-4/CU-4
<br />TYPE
<br />STRAIGHT COOL
<br />STRAIGHT COOL
<br />STRAIGHT COOL
<br />STRAIGHT COOL
<br />TOTAL COOLING CAP (MBH ® ARI)
<br />29.0
<br />47.0
<br />40.0
<br />23.0
<br />SENSIBLE COOLING CAP. (MBH 0 ARI)
<br />20.5
<br />33.0
<br />29.0
<br />17.0
<br />AHU CONFIGURATION
<br />VERTICAL
<br />VERTICAL
<br />VERTICAL
<br />VERTICAL
<br />SUPPLY AIR (CFM)
<br />1000
<br />1650
<br />1520
<br />790
<br />OUTSIDE AIR (CFM)
<br />150
<br />200
<br />230
<br />-
<br />EXTERNAL STATIC PRESS. (IN.WTR.)
<br />0.3
<br />0.3
<br />0.3
<br />0.3
<br />EVAPORATOR FAN
<br />HP
<br />1/3
<br />3/4
<br />1/2
<br />1/3
<br />VOLT/O
<br />240/1
<br />240/1
<br />240/1
<br />240/1
<br />FLA
<br />2,4
<br />4.3
<br />2.9
<br />1.7
<br />i
<br />ELECTRIC HEAT
<br />KW
<br />5
<br />8
<br />8
<br />-
<br />VOLT/0
<br />240/1
<br />240/1
<br />240/1
<br />-
<br />STAGES
<br />1
<br />1
<br />1
<br />-
<br />COMPRESSORS
<br />NUMBER
<br />1
<br />1
<br />1
<br />-
<br />VOLT/0
<br />240/1
<br />240/1
<br />240/1
<br />240/1
<br />RLA/LRA (EA)
<br />15.0/72.5
<br />24.4/140.0
<br />18.6/115.0
<br />9.2/43.0
<br />STAGING (%)
<br />0-100
<br />0-100
<br />0-100
<br />0-100
<br />CONDENSER FAN
<br />NUMBER
<br />1
<br />1
<br />1
<br />1
<br />VOLT/O
<br />240/1
<br />240/1
<br />240/1
<br />240/1
<br />MCA
<br />19.6
<br />31.9
<br />24.5
<br />13.0
<br />FLA (EA)
<br />0.8
<br />1.4
<br />1.1
<br />1.5
<br />AREA SERVED
<br />FITNESS RM.
<br />CLUB RM.
<br />OFFICES/LAUNDRY
<br />CABLE ROOM
<br />MANUFACTURER AHU/HP
<br />CARRIER/PAYNE
<br />PAYNE/PAYNE
<br />PAYNE/PAYNE
<br />PAYNE/PAYNE
<br />MODEL# AHU/HP
<br />FFIENP030/PA14NA030
<br />PF4MNA061/PA13NA048
<br />PF4MNA061/PA13NA042
<br />PF4MNA024/PA14NA024
<br />MINIMUM EER OR SEER
<br />14.0 SEER
<br />14.0 SEER
<br />14.0 SEER
<br />14.0 SEER
<br />OPERATING WEIGHT (AHU/CU)
<br />125/175
<br />175/250
<br />150/200
<br />125/175
<br />REMARKS
<br />1-10
<br />1-10
<br />1-10
<br />1-10
<br />NOTES:
<br />1. EXTERNAL STATIC PRESSURE AVAILABLE AFTER COIL FAN CASING, CLEAN FILTER AND ELECTRIC HEATER
<br />LOSSES.
<br />2. REFRIGERANT LINES AND INSULATION SHALL BE SIZED AND INSTALLED IN STRICT ACCORDANCE WITH
<br />MANUFACTURER'S RECOMMENDATIONS. PROVIDE SUBMITTALS ON INSULATION WITH EQUIPMENT SUBMITTALS.
<br />3. PROVIDE 1" THROWAWAY FILTERS.
<br />4. PROVIDE HEATING/COOLING PROGRAMMABLE THERMOSTAT AND 24 VOLT CONTROL WIRING. THERMOSTAT SHALL HAVE THE
<br />SAME NUMBER OF STAGES OF HEATING AND COOLING AS THE UNIT AND DUAL SETPOINT.
<br />5. PROVIDE 5 MINUTE TIME DELAY TO PREVENT COMPRESSOR SHORT CYCLING.
<br />6. MCA = MINIMUM CIRCUIT AMPACITY
<br />7. EXTERIOR INTERLOCK WIRING BETWEEN AHU AND CU MUST BE RUN IN LIQUIDTIfE FLEXIBLE CONDUIT.
<br />8. TRANE OR L.ENNOX COMPLYING WITH DESIGN PARAMETERS ARE APPROVED ALTERNATE MANUFACTURERS.
<br />9. PROVIDE WITH AHU FACTORY INSTALL CIRCUIT BREAKER.
<br />10. INDICATED SEER AMOUNTS ARE PER SCHEDULED CARRIER AHU do CU COMBINATIONS. CONTRACTOR MAY
<br />USE APPROVED ALTERNATE MANUFACTURER WITH A MINIMUM OF 14.0 SEER.
<br />I
<br />EXHAUST
<br />FAN SCHEDULE
<br />ELECTRICAL
<br />PLAN MARK
<br />MANUFACTURER/MODEL
<br />CFM
<br />E.S.P.
<br />DRIVE
<br />MOUNTING
<br />SONES
<br />REMARKS
<br />VOLT/
<br />AMPS
<br />PHASE
<br />EF-1
<br />AIR KING/AK150LS
<br />150
<br />.125
<br />DIRECT
<br />1.70
<br />115/1
<br />CEILING
<br />3.3
<br />1-4
<br />EF-2
<br />AIR KING/AK150LS
<br />150
<br />.125
<br />DIRECT
<br />1.70
<br />115/1
<br />CEILING
<br />3.3
<br />1-4
<br />EF-3
<br />AIR KING/AS50
<br />50
<br />.125
<br />DIRECT
<br />0.80
<br />115/1
<br />CEILING
<br />3.6
<br />1-4
<br />NOTES
<br />1. PROVIDE WITH DECORATIVE CEILING
<br />GRILLE
<br />2. CONTROL WITH ROOM LIGHTS
<br />3. PROVIDE WITH BACKDRAFT DAMPER.
<br />4. PROVIDE SPEED CONTROL
<br />GRILLE AND DIFFUSER SCHEDULE
<br />MARK
<br />MANUFACTURER/MODEL
<br />DESCRIPTION
<br />OBD
<br />MOUNTING
<br />COLOR
<br />MATERIAL
<br />REMARKS
<br />A
<br />US AIRE/1100
<br />ADJUSTABLE CURVED BLADE REGISTER
<br />Y
<br />CEILING
<br />WHITE
<br />STEEL
<br />1,2,3,4,5,6,7
<br />B
<br />US AIRE/1400
<br />CUBE CORE RETURN
<br />N
<br />CEILING
<br />ALUM.
<br />ALUM
<br />1,3,7
<br />1.
<br />SEE HVAC PLANS FOR NECK SIZES AND CFMS
<br />2.
<br />4-WAY UNLESS NOTED OTHERWISE ON PLAN BY ARROWS.
<br />3.
<br />MAXIMUM PRESSURE DROP OF .04 IN WC.
<br />4.
<br />TRANSITION ROUND FLEXIBLE OR RECTANGULAR RIGID DUCTWORK TO DIFFUSERS AS REQUIRED.
<br />5.
<br />HORIZONTAL DIMENSION GIVEN FIRST.
<br />6.
<br />PROVIDE OBD ADJUSTABLE FROM FACE OF GRILLE ON ALL DIFFUSERS.
<br />7.
<br />COORDINATE FINAL LOCATION WITH ARCHITECT OR OWNER.
<br />•,,,.rEN...� s SGM ENGINEERING INC.
<br />>'. No.60 F A C I L I T I ES C 0 N S U L T I N G EN G I N EE RS
<br />* * e 935 Lake Baldwin Lane TEL (407) 767-5188
<br />Baldwi(
<br />n Park, FAX: 407) 767-5772
<br />STAT F v Orlando, Florida 32814 CA-00006208
<br />As Project number. 2010-090
<br />�e� �� . •• `� www.sgmengineering.com
<br />ks ,I 60785 Copyright ©2010 SGM Engineering, Inc.
<br />//�lllll
<br />3
<br />ro
<br />aFORUME
<br />n
<br />L
<br />2
<br />ARCHITECTURE &
<br />INTERIOR DESIGN, INC.
<br />C
<br />.y PLANNING I ARCHITECTURE I INTERIOR DESIGN
<br />a
<br />0
<br />0 745 orienta avenue, suite 1121
<br />altamonte springs, fl 32701
<br />5 phone: 407.830.1400
<br />fax: 407.830.4143
<br />L' AA0002731
<br />t www.forumarchitecture.com
<br />Fort King
<br />Colony
<br />Apartments
<br />City of Zephyrhills, FL
<br />3 Bid & Permit Set
<br />2� SHEET REVISIONS:
<br />4
<br />..
<br />EDITED BY:
<br />c
<br />m
<br />r
<br />M 18.32
<br />NRP
<br />I- -
<br />I�II� I i - - - - - - - - - I I 1 11 1 , i lip i r-jTT ❑t r ,n ,t, i,i • 1,7_11ti-fs: r T-T T T- - r-- , -- - -� -- -
<br />
|