Laserfiche WebLink
NOT TO SCALE <br />CONDENSATE DRAIN <br />TO OUTSIDE <br />RUBBER G <br />1-1/2" DUCT BOARD <br />PLENUM LINER, R-5, <br />4 SIDES AND BOTTOM <br />FLOAT SWITCH IN SECONDARY DRAIN <br />LINE TO DISABLE AHU SHOULD <br />SECONDARY DRAIN LINE ACCUMULATE WATER. <br />AIR HANDLING UNIT <br />\-TO MAIN DRAIN PIPE <br />1-1/2" MIN <br />AM <br />MAINTAIN MANUFACTURERS RECOMMENDED SERVICE <br />ACCESS CLEARANCES FOR ALL MECHANICAL <br />EQUIPMENT, <br />OA DUCT <br />MANUAL <br />VOLUME <br />DAMPER <br />-FLEX CONNECTION <br />22 GA. GALVANIZED STEEL PLENUM/PLATFORM. <br />4 SIDED BOX WITH TOP AND BOTTOM FLANGES <br />OF 1-1/2" MINIMUM, <br />ELEVA I U®2 <br />NOT TO SCALE <br />SUPPLY <br />DUCT <br />INSULATED FLEXIBLE <br />DUCT <br />INSULATED <br />DIFFUSER <br />BOOT <br />CEILING <br />FOAM PLUG -CUT <br />INSULATE ENTIRE FLUSH AT CONDUIT ENTRANCE <br />LENGTH OF SUCTION[-PROVIDE <br />OR PACK WITH ROCK WOOL <br />LINE - <br />INSIDE <br />LIQUID LINE <br />APPLY TWO COATS OF VINYL -LACQUER <br />FINISH OR PROVIDE ALUMINUM JACKET ON <br />ALL EXTERIOR EXPOSED INSULATION <br />OUTSIDE <br />SEAL OPEN END WITH NON TOXIC <br />EXPANDABLE FOAM, AND CAULK <br />WEATHERTIGHT. TERMINATE 6" ABOVE <br />GROUND. <br />PVC CONDUIT WITH SOLVENT <br />WELDED JOINTS. 4"FOR UP TO <br />TWO SETS OF REFRIGERANT <br />LINES. 6"FOR UP TO 3 SETS 45• BEND <br />OF LINES. <br />(UNDERGROUND REFRIGERANT LINES <br />NOT TO SCALE <br />EXTERIOR WALL -%, <br />SEALANT ALL AROUND <br />SHEET METAL BOX TO BE 1 1/2- <br />MIN. LARGER THAN SLEEVE <br />BACKDRAFT DAMPER FOR DRYER <br />ONLY <br />CONTRACTOR TO PAINT W/ <br />WEATHER RESISTANT PAINT. <br />COLOR TO BE COORD. W/ <br />ARCHITECT/OWNER. <br />SHEET METAL DUCT <br />SLEEVE. SIZE AS <br />SHOWN ON PLANS. BtRDSCREEN FOR EXHAUST FAN ONLY (NOT DRYER VENT) <br />SEALANT ALL <br />AROUND <br />EXTERIOR WALL PENETRATION DETAIL <br />NOT TO SCALE <br />rF+�l <br />5`-0" MAXIMUM <br />MAXIMUM SAG 1/2" PER FOOT <br />OF SUPPORT SPACING. <br />FLEXIBLE DUCT <br />1, DUCT SHOULD EXTEND STRAIGHT FOR SEVERAL <br />INCHES FROM A CONNECTION BEFORE BENDING. <br />2, SUPPORT SYSTEM MUST NOT DAMAGE DUCT OR <br />CAUSE OUT -OF -ROUND SHAPE. <br />FLEX DUCT SUPPORT <br />NOT TO SCALE <br />12 GAUGE WIRE <br />OR 1/4" ROD TO <br />TOP CHORD OF <br />TRUSS <br />1 "X2"X1" <br />CHANNEL <br />SEAL DUCT <br />PENETRATION <br />WITH MASTIC <br />1AND 2 <br />22 GAUGE ANGLE <br />4"X2"X2" <br />[' 1E...1 <br />DUCT <br />1" WIDE 22 GAUGE <br />STRAP WRAPPING UNDER <br />DUCT AND ATTACHED TO <br />TOP CHORD OF TRUSS. <br />HANG FLEXIBLE DUCTS <br />WITH 1/2" WIDE 22 GA. <br />STEEL STRAPS WRAPPING <br />j UNDER DUCT EVERY 5 FT. <br />I! MAX, ALSO SUPPORT 18" <br />FROM ANY CONNECTION. <br />22 GAUGE, 4"X2"X2" <br />ANGLE AND FASTENERS <br />EVERY 8i. <br />PAWN117kIQIAVn IIAIrr <br />CONDENSING UNIT TIE DOWN <br />(MIAMI TECH, INC. CUTD1 <br />COLD -ROLLED GALV STEEL) <br />8 TOTAL FOR EACH UNIT <br />(1)1/4" DIA STAINLESS STEELSCREW <br />FROM STRAP TO CONDENSER <br />(1)3/16" DIA x 2" TAPCON <br />FROM STRAP TO CONC PAD <br />TYPICAL CONDENSING UNIT <br />ANCHORING DETAIL <br />NOT TO SCALE <br />STRAP 1 1/2" <br />MINIMUM <br />CEILING <br />14/12 <br />CONDENSATE DRAIN <br />TO OUTSIDE <br />TO SUIT EQUIP FURN. <br />4" TYP <br />UNIT <br />................................. <br />... <br />4" THICK REINF. <br />:. <br />CONCRETE PAD <br />W <br />SEE PLAN FOR <br />:- <br />UNIT LOCATION <br />O" <br />6 <br />............... <br />....... <br />l <br />4" SCH. 40 PVC CHASE, <br />REFRIGERANT PIPING <br />E INSTALL WITH LONG RADIUS <br />TO AIR HANDLING UNIT <br />' f <br />I ELLS. SEAL OPENING WITH <br />W®ATEER PROOF EXPANDING <br />CONDENSING <br />UNIT PAD DETAIL <br />12" MIN <br />FIN <br />I <br />FLOOR <br />CONDENSATE' <br />LINE <br />6" MIN. ABOVE FINISHED <br />GRADE ON SODDED OR <br />MULCHED AREAS ONLY <br />CONDENSATE PIPING <br />TERMINATION DETAIL <br />NOT TO SCALE <br />® o <br />RUBBER GASKET <br />18" X 18" RETURN GRILLE <br />1-1/2" DUCT BOARD <br />PLENUM LINER, R-5, <br />4 SIDES AND BOTTOM <br />1-1/2" MIN <br />NOTE: <br />MAINTAIN MANUFACTURERS <br />RECOMMENDED SERVICE ACCESS <br />CLEARANCES FOR ALL MECHANICAL <br />EQUIPMENT. <br />OUTSIDE AIR LOUVER <br />— 8" RND. OUTSIDE <br />AIR DUCT <br />VOLUME DAMPER <br />22 GA. GALVANIZED STEEL PLENUM/PLATFORM. <br />4 SIDED BOX WITH TOP AND BOTTOM FLANGES <br />OF 1-1/2" MINIMUM. <br />ELEVATION @ AHU-1 <br />NOT TO SCALE <br />2 III: <br />BOTTOM CHORD OF TRUSS <br />NOTE:SUPPORT DUCT AT EACH CHANGE OF DIRECTION. <br />`���tii1111��E� <br />:..., SGM ENGINEERING, INC. <br />FACILITIES CONSULTING ENGINEERS <br />NO. 607 _ 935 Lake Baldwin Lane TEL- (407 767-51M <br />* - Baldwin Park, FAX: (4071 767-5772 <br />DUCT SUPPORT DETAIL sTAT Orlando, Florida 32814 �► CA-00006208 <br />NOT TO SCALE 0 '•.,• � � (� Project number. 2010-090 <br />i Of .1 1 www.agmengineefing.com <br />-FL60785 Copyright ©2010 SGM Engineering, Inc. <br />���//llit►i1�` <br />- I�Ti711 a.l I Ili llll I O.d1 tid :AlC .11HU, Gnu Afil 1 1111It 11 46 .�-11i..-t. <br />3 <br />m <br />FORUME <br />L <br />2 <br />ARCHITECTURE & <br />INTERIOR DESIGN, INC. <br />.N PLANNING I ARCHITECTURE I INTERIOR DESIGN <br />$ 745 orienta avenue, suite 1121 <br />0 altamonte springs, fl 32701 <br />5 phone: 407.830.1400 <br />ad fax: 407.830.4143 <br />2 AA0002731 <br />t www.forumarchitecture.com <br />Fort King <br />Colony <br />Apartments <br />City of Zephyrhills, FL <br />SET DISTRIBUTIONS: <br />A SHEET REVISIONS: <br />I EDITED BY: NRP <br />PROJECT NO. 10-2651 <br />z <br />U <br />M 18.33 <br />0 <br />C� <br />