|
4/
<br />ELECTRICAL NO
<br />GENERAL NOTES:
<br />1. ALL WORK SHALL BE IN ACCORDANCE WITH THE CODE DATA LIST AND SHALL
<br />ALSO COMPLY WITH ALL APPLICABLE RULES AND REGULATIONS OF LOCAL AND STATE
<br />LAWS AND ORDINANCES.
<br />2. CONTRACTOR SHALL MAKE A THOROUGH EXAMINATION OF THE SITE AND THE
<br />CONTRACT DOCUMENTS. NO CLAIM FOR EXTRA COMPENSATION WILL BE RECOGNIZED IF
<br />DIFFICULTIES ARE ENCOUNTERED WHICH AN EXAMINATION OF SITE CONDITIONS AND
<br />CONTRACT DOCUMENTS PRIOR TO EXECUTING CONTRACT WOULD HAVE REVEALED.
<br />3. ELECTRICAL CONTRACTOR SHALL ARRANGE FOR ALL NECESSARY PERMITS,
<br />LICENSES, UTILITY COORDINATION, AND INSPECTIONS AS REQUIRED BY THE CITY OR
<br />UTILITY COMPANY. CONTRACTOR IS RESPONSIBLE FOR ALL EQUIPMENT REQUIRED BY
<br />UTILITY COMPANY AND SHOULD INCLUDE NECESSARY COSTS IN BID.
<br />4. CONTRACTOR SHALL LEGIBLY MARK-UP A SET OF 24'x36' DRAWINGS TO
<br />REFLECT AS -BUILT CONDITIONS, AND TURN OVER TO ARCHITECT.
<br />WIRE/RACEWAY:
<br />1. ALL CONDUCTORS SHALL BE COPPER, CONDUCTOR INSULATION SHALL BE DUAL
<br />TYPE THHN/THWN 750C. (1670F) FOR DRY, DAMP, AND WET LOCATIONS. CONDUCTOR
<br />INSULATION WITH SINGLE TYPE MARKING THHN 900C (1940F) MAY BE USED FOR DRY
<br />LOCATIONS ONLY. ALL CONDUCTORS SHALL BE COLOR CODED AS REQUIRED BY NEC
<br />AND FURTHER IDENTIFIED AND CODED AS SPECIFIED HEREINAFTER. COLOR CODING
<br />SHALL BE BY MEANS OF COLORED INSULATING MATERIAL, COLORED 13RAIO OR JACKET
<br />OVER THE INSULATION OR BY MEANS OF SUITABLE COLORED, PERMANENT, NON -AGING,
<br />INSULATING TAPE APPLIED TO CONDUCTORS AT EACH CABINET OR JUNCTION POINT.
<br />THE COLOR COOING SHALL BE ACCOMPLISHED AS THE CONDUCTORS ARE INSTALLED.
<br />THE FOLLOWING SYSTEMS OF COLOR CODING SHALL BE STRICTLY ADHERED TO:
<br />A) GROUND LEADS: GREEN
<br />B) 120/208 VOLT UNGROUNDED PHASE WIRES:
<br />PHASE A: BLACK
<br />PHASE B: RED
<br />PHASE C: BLUE
<br />NEUTRAL: WHITE
<br />THE COLOR CODE ASSIGNED TO EACH PHASE WIRE SHALL BE CONSISTENTLY
<br />FOLLOWED THROUGHOUT.
<br />2. UNLESS OTHERWISE INDICATED, ALL BRANCH CIRCUIT CONDUCTORS SHALL BE NO.
<br />12 AWG. ANY BRANCH CIRCUIT RUN OVER 75 FEET IN LENGTH, MEASURING ONE WAY
<br />FROM THE FIRST OUTLET OF THE CIRCUIT TO THE PANEL, SHALL BE NO. 10 AWG.
<br />FOR THE ENTIRE CIRCUIT.
<br />3. ALL INTERIOR BUILDING CONDUCTORS SHALL BE RUN IN THIN WALL CONDUIT
<br />AND THIN WALL CONDUIT SHALL BE UNDERWRITERS' APPROVED GALVANIZED
<br />ELECTRICAL METALLIC TUBING. COUPLINGS AND CONNECTORS SHALL BE STEEL
<br />SET -SCREW TYPE, ZINC OR CADMIUM PLATED. BELOW GRADE CONDUITS SHALL BE
<br />SCHEDULE 40 PVC WITH RIGID METAL ELBOWS AND RISERS. RIGID METAL CONDUIT
<br />BELOW GRADE OR IN CONCRETE SHALL BE COATED WITH BITUMASTIC OR SLEEVED
<br />WITH 10 MIL POLYETHYLENE. SITE CONDUITS SHALL BE ROUTED AT 24' BELOW
<br />GRADE AND CONDUITS ROUTED BELOW BUILDINGS SHALL BE AT 36'. EXTERIOR
<br />CONDUITS SHALL BE RIGID GALVANIZED STEEL.
<br />PENDING OWNER APPROVAL METAL CLAD CABLE (TYPE MC) IS ACCEPTABLE
<br />PROVIDED CABLE IS SUPPLIED WITH AN INSULATED GREEN EQUIPMENT GROUND
<br />CONDUCTOR AND MAY ONLY BE USED UNDER THE FOLLOWING CONDITIONS:
<br />A) SHORT RUNS IN WALLS.
<br />B) BETWEEN OUTLET BOXES IN HUNG OR FURRED CEILINGS, AND FLUSH TYPE
<br />LIGHTING FIXTURES AND TROUGH UNITS.
<br />C) CONNECTION TO EQUIPMENT IN SHELVING AND SHALL NOT BE USED FOR
<br />ANY CIRCUIT WITH OVER A 20 AMP CIRCUIT BREAKER.
<br />0) HOME -RUNS OF MULTI -CONDUCTOR CABLE WILL BE ALLOWED. CABLING
<br />MUST BE PROPERLY SUPPORTED AND COMPLY WITH ALL NEC CODES.
<br />MAXIMUM OF 9 CIRCUITS OR 13 CONDUCTORS IN A HOME -RUN.
<br />E) SHALL BE APPROVED FOR BRANCH CIRCUIT WIRING (20 AMPS & UNDER ONLY)
<br />IN CEILING SPACES AND WITHIN WALLS.
<br />METAL CLAD CABLE IS NOT ACCEPTABLE UNDER THE FOLLOWING CONDITIONS:
<br />A) BRANCH CIRCUITS OVER 20 AMPS.
<br />8) WHERE CABLING WILL BE EMBEDDED IN CONCRETE.
<br />C) WHERE CABLING WILL BE EXPOSED TO MOISTURE.
<br />0) WHERE PROHIBITED BY LOCAL CODE.
<br />4. COMBINING OF CIRCUITS IN SAME RACEWAY, OTHER THAN THOSE INDICATED ON
<br />DRAWINGS, WILL NOT BE PERMITTED.
<br />5. ALL RACEWAYS SHALL BE PROPERLY ALIGNED, GROUPED, AND SUPPORTED BY
<br />MECHANICAL TYPE 'CADDY' CLIPS AT INTERVALS NOT EXCEEDING 8 FEET.
<br />G. ALL RACEWAYS WITH NO. 10 OR 12 AWG PHASE CONDUCTORS FOR RECEPTACLES,
<br />LIGHTING FIXTURES AND SIMILAR CIRCUITS SHALL BE PROVIDED WITH A PARITY
<br />SIZED GREEN EQUIPMENT GROUND CONDUCTOR. GROUND CONDUCTOR SHALL BE
<br />INSTALLED IN ENTIRE RACEWAY SYSTEM INCLUDING WALL SWITCHES AND FLEXIBLE
<br />CONDUIT TO LIGHT FIXTURES. EQUIPMENT GROUND CONDUCTOR SIZES FOR CIRCUITS
<br />WITH PHASE CONDUCTORS LARGER THAN NO. 12 AWG ARE INDICATED ON DRAWINGS.
<br />GROUND CONDUCTORS SHALL BE CONNECTED TO GROUND BUSS IN PANELBOARDS.
<br />7. RACEWAY PENETRATIONS OF FIRE RATED WALLS AND/OR FLOORS SHALL BE
<br />SEALED TO MAINTAIN INTEGRITY OF CONSTRUCTION. ALL PRODUCTS, MATERIALS AND
<br />METHODS OF INSTALLATION SHALL BE UL APPROVED AND MEET NFPA.
<br />GROUNDING:
<br />1. THE ENTIRE ELECTRICAL SYSTEM SHALL BE COMPLETELY AND EFFECTIVELY
<br />GROUNDED AS REQUIRED BY NATIONAL ELECTRICAL CODE. ALL METALLIC RACEWAYS
<br />SHALL BE MECHANICALLY AND ELECTRICALLY SECURE AT ALL JOINTS AND AT ALL
<br />BOXES, CABINETS, FITTINGS AND EQUIPMENT.
<br />2. THE GROUNDING SYSTEM SHALL BE TESTED BY THE CONTRACTOR. THE
<br />RESISTANCE TO GROUND SHALL BE NO MORE THAN FIVE (5) OHMS. SUBMIT TEST
<br />RESULTS TO ENGINEER. CONTRACTOR SHALL MAKE UPGRADES AND ADDITIONS TO
<br />GROUNDING SYSTEM AS REQUIRED TO ACHIEVE THE (5) OHM REQUIREMENT.
<br />3. PROVIDE NO. 6 AWG GROUND CONDUCTOR AT TELEPHONE BOARD AND CONNECTION
<br />TO THE MAIN SERVICE ENTRANCE GROUND. PROVIDE 1OFT. OF SLACK AT BOARD.
<br />OUTLET BOXES/DEVICES:
<br />1. COORDINATE DEVICE AND COVER PLATE COLORS WITH ARCHITECT.
<br />2. ALL OUTLET BOXES SHALL BE RIGIDLY MOUNTED AND SHALL BE EQUIPPED WITH
<br />SUITABLE SCREW FASTENED COVERS. OPEN KNOCKOUTS OR HOLES IN BOXES SHALL
<br />BE PLUGGED WITH SUITABLE BLANKING DEVICE.
<br />3. OUTLET BOXES SHALL BE 4 INCH OCTAGONAL x 2-1/8' DEEP. OUTLET BOXES
<br />LOCATED ABOVE THE CEILING SHALL BE LEGIBLY IDENTIFIED WITH BRANCH CIRCUIT
<br />NUMBER OF CIRCUIT TERMINATED WITHIN BY MEANS OF BLACK PERMANENT MARKER.
<br />4. NEC 210.12(A) ALL 120 VOLT, SINGLE PHASE, 1S & 20 AMPERE BRANCH CIRCUITS
<br />SUPPLYING OUTLETS OR DEVICES INSTALLED IN DWELLING UNIT KITCHENS, FAMILY
<br />ROOMS ' DINING ROOMS, LIVING ROOMS, PARLORS, LIBRARIES, DENS, BEDROOMS,
<br />SUNROOMS, RECREATION ROOMS, CLOSETS, HALLWAYS, LAUNDRY AREAS OR SIMILAR
<br />ROOMS OR AREAS SHALL BE PROTECTED BY ARC -FAULT CIRCUIT INTERRUPTER.
<br />5. NEC 406.12 ALL 15 & 20 AMPERE, 125 & 250 VOLT NON -LOCKING -TYPE
<br />RECEPTACLES IN DWELLING UNITS SHALL BE TAMPER- RESI S TANT RECEPTACLES.
<br />6. NEC 210.8 ALL 125 VOLT, 15 & 20 AMPERE RECEPTACLES INSTALLED IN
<br />BATHROOMS, GARAGES, AND ALSO ACCESSORY BUILDINGS THAT HAVE A FLOOR
<br />LOCATED AT OR BELOW GRADE LEVEL NOT INTENDED AS HABITABLE ROOMS AND
<br />LIMITED TO STORAGE AREAS, WORK AREAS, AND AREAS OF SIMILAR USE, OUTDOORS,
<br />CRAW SPACES, UNFINISHED PORTIONS OR AREA OF THE BASEMENT NOT INTENDED AS
<br />HABITABLE ROOMS, KITCHENS WHERE THE RECEPTACLES ARE INSTALLED TO SERVE
<br />THE COUNTERTOP SURFACES, SINKS WHERE RECPTACLES ARE INSTALLED WITH IN 6
<br />FEET FROM THE TOP INSIDE EDGE OF THE SINK BOWL OF THE SINK, BOATHOUSE,
<br />BATHTUBS OR SHOWER STALL WHERE RECEPTACLES ARE INSTALLED WITHIN 6 FEET
<br />OF THE OUTSIDE EDGE OF THE BATHTUB OR SHOWER STALL, & LAUNDRY AREAS.
<br />SWITCHGEAR:
<br />1. PANELBOARDS SHALL BE MANUFACTURED BY SQUARE 'D' COMPANY, TYPE AS
<br />SHOWN ON DRAWINGS OR APPROVED EQUAL. FURNISH WITH COPPER BUS BARS,
<br />COPPER EQUIPMENT GROUND BUS AND BOLT -ON CIRCUIT BREAKERS.
<br />2. DISCONNECT SWITCHES SHALL BE HEAVY-DUTY TYPE AND MANUFACTURED BY
<br />SQUARE 'D' COMPANY OR APPROVED EQUAL. FUSES SHALL BE DUAL ELEMENT,
<br />CARTRIDGE TYPE. FUSES SHALL BE BY ONE MANUFACTURER: BUSSMAN 'FUSETRON' OR
<br />CHASE-SHAWMUT 'TRIONIC.
<br />3. INSTALL ENGRAVED PLASTIC -LAMINATE LABELS ON EACH MAJOR UNIT OF
<br />ELECTRICAL EQUIPMENT IDENTIFYING PANELBOARD NAME OR EQUIPMENT SERVING.
<br />EXAMPLES ARE, PANELBOPRGS, OISCONNECT SWITCHES, AND MOTOR STARTERS, I.E.
<br />LABELS SHALL BE 1/16' THICK BEA�-K PLASTIC LAMINATE WITH 3/8' WHITE CORE
<br />PLIE LETTERS.
<br />4. PANELBOARD DIRECTORY CARDS SHALL BE TYPEWRITTEN WITH ACCURATE AND
<br />CURRENT INFORMATION BY THE CONTRACTOR AT THE END OF CONSTRUCTION.
<br />5. ALL MULTI -WIRE BRANCH CIRCUIT C IRCUI T -BREAKERS ARE TO BE TIED
<br />TOGETHER BY AN IDENTIFIED HANDLE -TIE OR BY A COMMON TRIP CIRCUIT BREAKER
<br />PER
<br />NEC SECTION 210.4(B).
<br />LIGHTING FIXTURES:
<br />1. THE CONTRACTOR SHALL FURNISH AND INSTALL COMPLETE IN ALL RESPECTS
<br />ALL LIGHTING FIXTURES LISTED IN THE FIXTURE SCHEDULE.
<br />2. THE CONTRACTOR SHALL SUBMIT CATALOG CUTS OF ALL THE FIXTURES TO THE
<br />ARCHITECT. THESE CUTS SHALL BE SUBMITTED IMMEDIATELY AFTER THE
<br />CONTRACTOR HAS RECEIVED AN APPROVED MATERIAL LIST FROM THE ARCHITECT.
<br />3. BALLASTS FOR FLUORESCENT LAMPS SHALL BE ELECTRONIC RAPID START WITH
<br /><10% TOTAL HARMONIC DISTORTION MANUFACTURED BY 'OSRAM SYLVANIA. ALL
<br />BALLASTS FOR FLUORESCENT FIXTURES SHALL BE INDIVIDUALLY FUSED. FUSES
<br />SHALL BE INSTALLED ON THE LINE SIDE OF THE BALLAST.
<br />4. FLUORESCENT LAMPS SHALL BE RAPID START, TB/32 WATT, 3500K. ALL LAMPS
<br />SHALL BE AS MANUFACTURED BY SYLVANIA.
<br />5. ALL FIXTURES SHALL BE PROPERLY AND CAREFULLY SUPPORTED AND ALIGNED,
<br />AND THE CONTRACTOR SHALL FURNISH AND INSTALL ALL NECESSARY STEEL SHAPES,
<br />ETC., FOR SUPPORT OF FIXTURES AS REQUIRED AND DETAILED ON THE DRAWINGS.
<br />PROVIDE JUNCTION BOX STEM MOUNTED FROM DECK TO SUPPORT ALL CEILING
<br />MOUNTED EXIT LIGHTS.
<br />6. LIGHTING FIXTURES SHALL BE CLEAN AND LAMPED WITH NEW LAMPS AT THE
<br />TIME OF FINAL INSPECTION.
<br />7. COORDINATE ALL LOCATIONS OF LIGHTING FIXTURES WITH ARCHITECTURAL
<br />DRAWINGS.
<br />B. ALL FLUORESCENT FIXTURES SHALL HAVE A DISCONNECTING MEANS EITHER
<br />INTERNAL OR EXTERNAL IN ACCORDANCE WITH NEC ARTICLE 410.73(G).
<br />OCCUPANCY SENSORS:
<br />1. CONTRACTOR SHALL SUBMIT SHOP DRAWINGS SHOWING LOCATIONS OF ALL UNITS
<br />AND CUT SHEETS FOR ALL DEVICES.
<br />LIGHTING & SMOKE NOTES:
<br />1. FLORIDA BUILDING CODE 907.2.11.2 & 908.7.2 INSTALL ON THE CEILING OR
<br />WALL INSIDE OR DIRECTLY OUTSIDE OF EACH ROOM USED FOR SLEEPING PURPOSES.
<br />2. FLORIDA BUILDING CODE 907.2.11.4 POWER SOURCE IN NEW CONSTRUCTION
<br />REQUIRED SMOKE ALARM ALARM SHALL RECEIVE THEIR PRIMARY POWER FROM THE
<br />BUILDING WIRING WHERE SUCH WIRING IS SERVED FROM A COMMERCIAL SOURCE AND
<br />SHALL BE EQUIPPED WITH A BATTERY BACKUP.
<br />3. WHERE MORE THAN ONE SMOKE ALARM IS REQUIRED TO BE INSTALLED SHALL
<br />BE INTERCONNECTED IN SUCH A MANNER THAT THE ACTIVATION OF ONE WILL
<br />ACTIVATE ALL OF THE ALARMS IN THE INDIVIDUAL UNIT.
<br />4. NEC 210.12(A) ALL LIGHT SWITCH FEEDING AN OUTSIDE SHALL BE ARC FAULT
<br />BREAKER.
<br />SINGLE -LINE DIAGRAM KEY NOTES
<br />1. MAXIMUM SYMMETRICAL RMS FAULT CURRENT. ALL PANELBOAROS AND BREAKERS
<br />SHALL BE CAPABLE OF WITHSTANDING THE MOMENTARY FAULT CURRENT LEVEL
<br />SHOWN.
<br />2. UTILITY APPROVED METER WITH 50A/1P BREAKER. A HEAVY-DUTY JAW
<br />RELEASE METER ENCLOSURE WITH LEVER TYPE BY-PASS SHALL BE INSTALLED.
<br />POINT OF
<br />ATTACHMENT
<br />3 #4 CU
<br />1 #8 CU EG
<br />1 1/2' C
<br />F_
<br />12' X 12' X 6
<br />PVC J-BOX
<br />WITH GASKET
<br />COVER
<br />NEW
<br />SURGE 50 A
<br />PANEL 8
<br />PROTECTIVE
<br />DEVICE �PO 120/208
<br />ATLANTIC I PHASE
<br />SCIENTIFIC TYPE 3R
<br />#161-208V
<br />4 SER
<br />EXISTING
<br />DECK
<br />EXISTING
<br />OVERHEAD
<br />FEED
<br />1-0 Lz_0
<br />3 #4 CU NEW EXISTING EXISTING
<br />1 #8 CU EG 50 A A/C 100 A
<br />DISCONNECT
<br />1 1/ 2' C METER METER
<br /># 8CU
<br />CONNECTED TO
<br />SUPPLEMENTAL
<br />ELECTRODS
<br />PER
<br />NEC 250.53
<br />3/4' x 10'-0" COPPER CLAD GROUND ROD. PLACE A MINIMUM OF
<br />10'-D' APART IN RECESSED CONCRETE TEST WELL WITH STEEL
<br />COVER PLATE. GROUNDING SYSTEM MUST BE TESTED AND BE
<br />5 OHMS OR LESS.
<br />NO.3/0 CU CONNECTED TO SUPPLEMENTAL ELECTRODES
<br />PER NEC 250.53.
<br />BONDING OF COMMUNICATION SHALL MEET TO NEC 250.94(A) 1-6 OF
<br />INTERSYSTEM BONDING.
<br />NEW PANEL A
<br />LOCATED IN
<br />CUSTODIAL
<br />CLOSET
<br />U
<br />NEW �OILET
<br />ROOM BUILDING
<br />I
<br />1 1/2' C
<br />BELOW
<br />EXISTING
<br />PARKING
<br />GRADE PUL BOX
<br />1 1/2' J
<br />IN ATTIC/
<br />EXISTING
<br />RESTAURANT
<br />BUILDING
<br />EXISTING NEW
<br />100 A 50 A
<br />METER METER
<br />EXISTING
<br />100 A PANEL
<br />EXISTING
<br />EXISTING
<br />A/C
<br />FENCE
<br />I
<br />UNITS
<br />PARTIAL SITE PLAN
<br />90 I -off
<br />1/16 1
<br />EXISTING
<br />100 A
<br />PANEL
<br />SINGLE -LINE DIAGRAM
<br />NTS
<br />NORTH
<br />GFI 36' AFF
<br />COORDINATE HEIGF
<br />WITH HAND ORYE
<br />REQUIREMENTS
<br />i L
<br />in
<br />'d
<br />jB-3
<br />1�. -
<br />UITCH TO
<br />INTROL
<br />OONWLIGHT
<br />Lj
<br />DO Li
<br />0C
<br />S
<br />1312
<br />ILISWIT H T SWITCH TO
<br />CONTR L
<br />IAREA CONTROL
<br />AREA
<br />FIXT ES
<br />Eo FIXTURES
<br />Cls LA 0S
<br />_T
<br />LIGHTING P LAN
<br />I -off
<br />4/ 0
<br />1 /4
<br />GFI
<br />all
<br />0�4
<br />B_
<br />IDCC SENSOR
<br />TO CONTROL
<br />1EIGHTINGFAt4E
<br />XHAUST FAN
<br />GF
<br />q"11:4ra
<br />o
<br />PANEL 8
<br />0
<br />0
<br />0
<br />A-
<br />3BCj
<br />C
<br />GFI
<br />137
<br />OCC SENSOR
<br />TO CONTROL
<br />LIGHTING ANO
<br />EXHAUST FAM
<br />ELECTRICAL PLAN NOTE
<br />1. CONTRACTOR TO PROVIDE ALL WIRING, CONDUIT, MATERIALS, EQUIPMENT,
<br />ETC., SHOWN OR REQUIRED TO COMPLETE THE ELECTRICAL WORK UNLESS
<br />OTHERWISE SPECIFIED. ANY ITEM OR SYSTEM WHICH IS SHOWN, MENTIONED OR
<br />REASONABLY IMPLIED ON EITHER DRAWINGS OR IN THE SPECIFICATIONS SHALL
<br />BE CONSIDERED TO BE PROPERLY AND SUFFICIENTLY SPECIFIED ANO SHOWN,
<br />AND MUST BE PROVIDED. INCLUDE ALL LABOR, EQUIPMENT, TOOLS, ETC.,
<br />REQUIRED TO COMPLETE ALL INSTALLATIONS AS INTENDED. INSTALL ALL
<br />EQUIPMENT ACCORDING TO THE METHOD INDICATED, MANUFACTURERS
<br />INSTRUCTIONS OR ACCORDING TO STANDARD INDUSTRY PRACTICES IF NO
<br />INSTALLATION TECHNIQUE IS DEFINED.
<br />2. CONTRACTOR TO PROVIDE ALL WORK AND MATERIALS IN ACCORDANCE WITH
<br />THE LATEST EDITIONS OF THE NATIONAL ELECTRICAL CODE (N.E.C.), THE
<br />FLORIDA BUILDING CODE, APPLICABLE NFPA AND UL STANDARDS, AND ALL
<br />OTHER APPLICABLE FEDERAL, STATE AND LOCAL CODES AND REGULATIONS. ANY
<br />MATERIALS, EQUIPMENT OR INSTALLATIONS NOT MEETING ALL REQUIREMENTS
<br />OF THE APPROPRIATE REGULATORY AGENCIES WILL NOT BE ACCEPTED. IT IS
<br />THE CONTRACTOR'S RESPONSIBILITY TO ENSURE THE REQUIREMENTS ARE MET
<br />AND PROVIDE EVIDENCE OF SUCH IF REQUESTED.
<br />3. PER FLORIDA BUILDING CODE 2017, TABLE C405.2(2). THE ALLOWED LIGHTING
<br />LOAD FOR RESTROOMS IS LPD = .98. THE ALLOWABLE LOAD IS 329 WATTS.
<br />THE ACTUAL LOAD FOR THIS SPACE IS 143 WATTS WHICH COMPLIES.
<br />4. PER FBC ENERGY CONSERVATION SECTION C405.2 PROVIDE MANUAL AND
<br />AUTOMATIC CONTROLS IN ALL SPACES.
<br />5. PER FBC ENERGY CONSERVATION 408.3 A FUNCTIONAL TEST OF THE LIGHTING
<br />CONTROLS SYSTEMS WILL BE PERFORMED. THE LIGHTING CONTROL SYSTEM TO
<br />BE TESTED TO ENSURE THAT CONTROL HARDWARE AND SOFTWARE ARE
<br />CALIBRATED, ADJUSTED, PROGRAMED AND IN PROPER WORKING CONDITION IN
<br />ACCORDANCE WITH THESE DOCUMENTS AND MANUFACTURES INSTRUCTIONS.
<br />G. DRAWINGS AMO OPERATION AND MAINTENANCE MANUALS TO 13E PROVIDED TO
<br />THE OWNER PER FBO ENERGY CONSERVATION SECTION C405.6.4. CLEARLY
<br />IDENTIFY ROUTINE MAINTENANCE REQUIREMENTS. PROVIDE THE NAME, ADDRESS
<br />AND PHONE NUMBER FOR A QUALIFIED SERVICE AGENCY.
<br />7. ELECTRICAL PANEL LAK1.1.139.OR.P2 IS EXISTING 1201208 3 PHASE 4 WIRE
<br />200 AMP 42 CIRCUIT PANEL. AIC 10,000. PANEL IS LOCATED IN THE PANEL
<br />ROOM - SEE DIAGRAM AT THE LEFT. NO NEW PANELS ARE TO BE PROVIDED.
<br />LIGHTING CIRCUITS ARE EXISTING. EXISTING 20 AMP BREAKERS AT CIRCUIT
<br />31, 32, 33, 34 ARE DESIGNATED FOR PROJECT'S NEW POWER RECEPTACLES.
<br />B. NOTE NOT USED
<br />9. ALL EXIT LIGHTS TO BE CONNECTED TO LIGHTING CIRCUIT FOR THAT AREA.
<br />10. ALL EXIT AND EMERGENCY LIGHTS OVER EXISTING EXTERIOR DOORS. ALL
<br />EXIT AND EMERGENCY LIGHTS OVER EXISTING EXTERIOR DOORS AND AT
<br />CORRIDORS ARE EXISTING AND SHALL REMAIN IN PLACE.
<br />11. NOTE NOT USED
<br />12. GENERAL CONTRACTOR SHALL INSURE/VERIFY THAT LOCATIONS INDICATED
<br />FOR ELECTRICAL CORRESPOND WITH STANDARD FIXTURES AS INDICATED ON
<br />ELEVATION, PLAN & DETAIL SHEET(S). ANY DISCREPANCIES SHALL BE
<br />REPORTED TO THE OWNER PRIOR TO INSTALLATION OF FIXTURES AND
<br />ELECTRICAL EQUIPMENT. DISCREPANCIES REPORTED FOLLOWING INSTALLATION
<br />ARE THE SOLE RESPONSABILITY OF THE GENERAL CONTRACTOR.
<br />13. NOTE NOT USED
<br />14. NOTE NOT USED
<br />15. WHEN THE ELECTRICAL PANEL IS EXPOSED TO THE FLOOR/PUBLIC, THE
<br />ELECTRICAL PANEL SHALL BE ENCLOSED IN A CLOSET WITH ACCESS DOOR
<br />MEETING ALL NEC CODES AND ANSI/AOAAG CODES AROUND THE CLOSET.
<br />16. ALL FIXTURES ARE PROVIDED BY THE OWNER AND INSTALLED BY THE
<br />GENERAL CONTRACTOR.
<br />17. ADD APPROXIMATELY (4) NEW 1X4 LEO 35W LIGHT FIXTURES AND I 15W
<br />RECESSED CAN DOWNLIGHT. FIELD VERIFY EXACT FIXTURE NUMBER.
<br />le. FOR ADDITIONAL INFORMATION ON EQUIPMENT SPECIFICATIONS, SEE SPEC
<br />SHEETS.
<br />GFI 36' AFF
<br />GF1 COORDINATE HEIGHT
<br />WITH HAND DRYER
<br />REQUIREMENTS
<br />fow
<br />ot
<br />POWER PLAN
<br />1/4 of
<br />1 4/ 0 21 41
<br />PANEL SCHEDULE
<br />PANEL AND BREAKERS WILL TIE TO EXISTING.
<br />PANEL B AMPS: 50 VOLTAGE: 120/208 PHASE: SINGLE
<br />TYPE: 3R AIC:10,000 LOCATION: OUTDOOR RATED - CUSTODIAL CLOSET OF NEW BLD'G
<br />nTc;rPTPTTnN RR rTR CTR RR DISCRTPTION
<br />MEN GFI
<br />20
<br />1
<br />2
<br />20
<br />WOMEN GFI
<br />MEN FART FAN 1
<br />20
<br />3
<br />4
<br />20
<br />WOMEN FART FAN I
<br />MEN FAN 2
<br />20/2
<br />1
<br />5
<br />6
<br />20/2
<br />WOMEN FAN 2
<br />1 7
<br />1 8
<br />MEN MAINT GFI
<br />20
<br />9
<br />10
<br />20
<br />WOMEN MAINT GFI
<br />JAN GFI
<br />20
<br />11
<br />12
<br />20
<br />SIGNAGE
<br />LEG�ND
<br />j 1 X 4 32W SURFACE MOUNTED LED LIGHTING FIXTURE
<br />SINGLE POLE SWITCH W/ OCCUPANCY SENSOR CONTROL
<br />110S
<br />0 DAYLIGHT HARVESTING CONTROLLER CEILING MOUNTED
<br />CIRCUIT RUN CONCEALED UNDER FLOOR OR BENEATH GRADE
<br />HOMERUN TO PANEL, LETTERS INDICATE PANEL, NUMBERS
<br />INCIOCATE CIRCUIT. ANY CIRCUIT WITHOUT FURTHER
<br />DESIGNATION INDICATES A 2-WIRE & EQUIPMENT GROUND.
<br />EXIT SIGN - NEW BEGHLLI VA4-5-HT SURFACE MOUNT
<br />UNV LEO RED BACK LIT LETTERS ON WHITE BACKGROUND
<br />EMERGENCY LIGHTS - NEW BEGHELLI XMR-650 SURFACE
<br />MOUNT UNV 2W 2 HEAD LED EMERGENCY LIGHT WITH
<br />BATTERY BACK-UP
<br />@GFI
<br />2-OUTLET GFI RECEPTACLE: Standard 120V GFI OupLex
<br />ELectricaL ReceptacLe mounted at 6' above counter
<br />with white pLastic cover unLess otherwise noted.
<br />EF 1 - EXHAUST FAN PANASONIC FV-40VQ4
<br />380
<br />380 CFM 3 SONES 17"X15" X9"D
<br />Ic><01
<br />EF 2 - WALL MOUNTED VENTAMATIC LTD IF14 EXHAUST FAN
<br />1400 CFM, 14", 120V, 17" X 17" ROUGH OPENING
<br />FLOOR DRAIN
<br />OVERHEAD DUCTING & EXHAUST GRILL WITH WEATHERHEAD
<br />0
<br />-0
<br />0
<br />0-
<br />0
<br />-+_
<br />U
<br />1�0
<br />MA
<br />N"
<br />ry
<br />t:�
<br />C=
<br />0
<br />Cn
<br />L&_j
<br />ry
<br />C)e
<br />0
<br />(0
<br />L0
<br />C:)
<br />00
<br />P0 E
<br />re)
<br />0
<br />i 1�
<br />LL_
<br />:S CL
<br />>
<br />ED
<br />��e
<br />:S 0
<br />.0 U-)
<br />> (0
<br />CN7 00
<br />U-)
<br />C14
<br />NO
<br />W t-)
<br />L: C�
<br />Z:) r-
<br />Lri
<br />U')
<br />C-4
<br />rrj
<br />CD
<br />V) CR C:)
<br />C:)
<br />rn
<br />C)
<br />C)
<br />co
<br />C14
<br />C-)
<br />V) U-)
<br />< Id:
<br />M C)
<br />U-3
<br />V) "d:
<br />C:> ff -> C)
<br />to I
<br />00 LL_
<br />00
<br />Ln
<br />L1=5
<br />>
<br />-<
<br />rn
<br />L__
<br />r-,
<br />cf�
<br />cn
<br />ro
<br />0
<br />(-)
<br />ID
<br />o
<br />_..,
<br />En
<br />0
<br />LL_
<br />(z)
<br />C_
<br />LLJ
<br />C)
<br />zt:�
<br />00
<br />E
<br />0
<br />-r-
<br />C"i
<br />00
<br />Q)
<br />--C)
<br />Cf)
<br />0
<br />C14
<br />.d-
<br />LO
<br />r1r)
<br />C_
<br />U
<br />iE
<br />Q)
<br />C- NO
<br />C)
<br />LO
<br />cl-
<br />1
<br />0
<br />C*4
<br />ir
<br />0
<br />M
<br />W
<br />R
<br />0-
<br />MO
<br />R 0
<br />000
<br />5; 3 Uj
<br />19CO29
<br />review 06-13-2019
<br />approval
<br />permit 07-29-2019
<br />revision
<br />revision
<br />E-101
<br />
|