|
-- -- --------
<br />AS
<br />REQUIRED PER ZONE
<br />FOR CONTROL OF 0-10V LOADS
<br />r---------------------------------------�
<br />I
<br />ZONE X
<br />SWITCHED POWER
<br />(8A MAX)
<br />I I
<br />I I ® I
<br />0-10V DIM
<br />(60 mA MAX)
<br />RMJS-8T-DV-B
<br />POWPAK DIMMING MODULE
<br />120/277V-, 50/60 Hz
<br />W/ 0-10 V CONTROL
<br />DIMENSIONS:
<br />3.42"(H) X 2.82"(W) X 1.25"(D)
<br />I (87mm X 72mm X 32mm) I
<br />LOCATE ABOVE ACCESSIBLE CEILING
<br />I I
<br />IL---------------------------------------J
<br />TYPICAL QS
<br />TIMECLOCK
<br />AS REQUIRED
<br />----------------
<br />I I
<br />I I
<br />I OQ I
<br />I
<br />QSGR-TC-3S-WH-CPN5825 I
<br />QS TIMECLOCK
<br />w/ 3 SHADE COLUMNS
<br />(4 GANG US BACKBOX BY OTHERS)
<br />LOCATE IN MAIN ELECTRICAL CLOSET
<br />I I
<br />L------------------------------t
<br />TYPICAL OF RESTROOMS
<br />AS
<br />REQUIRED
<br />r---------------------------------
<br />I I
<br />I I
<br />i
<br />I I
<br />I I
<br />I I
<br />(1) PJ2-2BRL-GWH-XXX
<br />434 MHZ PICO WIRELESS
<br />2 BUTTON CONTROL WITH RAISE/LOWER
<br />SHOWN WITH CW-2-WH
<br />CLARO WALLPLATE
<br />*SEE SPECIFICATION SHEET FOR
<br />DIMENSIONS, ENGRAVING OPTIONS,
<br />& MOUNTING INSTRUCTIONS
<br />I I
<br />REFER TO FLOOR PLAN FOR
<br />QUANTITY AND LOCATIONS
<br />--------------------------------
<br />I I
<br />AS REQUIRED
<br />FOR CONTROL OF NORMAL 0-10V & NON -DIM LOADS
<br />ZONES
<br />r-------------------------------------
<br />I I
<br />I I
<br />ZONE X
<br />120V/277V E1`0
<br />120V/277V
<br />120V/277V
<br />120V/277V E3--
<br />120/277V
<br />I
<br />TO QUANTUM HkJB&Q
<br />0-10V
<br />I
<br />I
<br />ZONE X
<br />0-10V
<br />I
<br />®
<br />I
<br />ZONE X
<br />0-10V
<br />I
<br />ZONE X
<br />0-10V I
<br />ESN#
<br />To QS Devices
<br />(Up to 14 PDUs)
<br />QSN-4T16-S
<br />ENERGI SAVR NODE QS (ESN)
<br />WITH (4) SWITCHED OUTPUTS,
<br />(4) 0-10V CHANNELS, AND
<br />I I
<br />(1) QS COMMUNICATIONS LINK
<br />DIMENSIONS:
<br />13.25"[336,7mm] (H) X 9.25"[235mm] (W)
<br />X 3.16"[80,3mm] (D)
<br />LOCATE ABOVE ACCESSIBLE CEILING
<br />I I
<br />L------------------------------------J
<br />LUTRON PROVIDED JACK OR (FOR US INSTALLATIONS ONLY)
<br />OQ ETHERNET PORT BY OTHERS C-ESN-SETUP
<br />a <<<
<br />(WIRELESS ROUTER
<br />QSE-CI-AP-D NT-05E/B-NFB-WH-E-CPW1338
<br />ENERGI SAVR NODE LUTRON LIGHTING SYSTEM APPLE®IPOD TOUCH
<br />PROGRAMMING INTERFACE DEDICATED PROGRAMMING PORT OR IPHONE"MOBILE
<br />DIMENSIONS: (1 GANG US BACKBOX BY OTHERS) DIGITAL DEVICE
<br />3.5"[89mm] (H) X 2.1"[53mm] (Vv) — — — — — — — —
<br />X 2.4"[61 mm] (D)
<br />LOCATION TBD
<br />TYPICAL OF OPEN AREA AND KITCHEN
<br />AS
<br />I
<br />REQUIRED
<br />r-----------------------------�
<br />I I
<br />I I I
<br />I I
<br />LRF2-VCR2B-P-WH
<br />434MHZ WIRELESS I I
<br />OCCUPANCY SENSOR i I
<br />3.57"[90,7mm] (DIA) X 1.13"[28,7mm] (D)
<br />MAX 10 PER QSM
<br />*DEVICE IS SURFACE -MOUNTED AND
<br />BATTERY POWERED, DOES NOT i I
<br />REQUIRE POWER FEED
<br />I I
<br />I I
<br />(OPTION:WITH L-CRMK-WH i I
<br />RECESS MOUNT KIT FOR I
<br />NON-METALLIC CEILINGS)
<br />REFER TO FLOOR PLAN FOR
<br />QUANTITY AND LOCATIONS
<br />L----------------------------- J
<br />TYPICAL OF SALE AREA AND BACK OF HOUSE
<br />AS REQUIRED
<br />MAX OF 10 PER QSM
<br />r----------------------------
<br />I I
<br />I I I
<br />I I
<br />I I
<br />I I
<br />LRF2-OCR2B-P-WH
<br />I i 434MHZ WIRELESS
<br />OCCUPANCY/VACANCY SENSOR
<br />I 3.57"[90,7mm] (DIA) X 1.13"[28,7mm] (D) I
<br />MAX 10 PER QSM
<br />I i -DEVICE IS SURFACE -MOUNTED AND
<br />BATTERY POWERED, DOES NOT
<br />REQUIRE POWER FEED
<br />I I
<br />I i (OPTION:WITH L-CRMK-WH
<br />RECESS MOUNT KIT FOR
<br />NON-METALLIC CEILINGS)
<br />REFER TO FLOOR PLAN FOR
<br />QUANTITY AND LOCATIONS
<br />LL---------------------------J
<br />AS REQUIRED
<br />--------------------
<br />I I
<br />I I
<br />I I
<br />I I
<br />QSM#
<br />I QQ I
<br />I I
<br />QSM2-4W C
<br />QUANTUM SENSOR MODULE (QSM)
<br />WITH (4) UNIVERSAL WIRED INPUTS
<br />AND 434MHZ WIRELESS RECEIVER I
<br />60'[18.29m] RADIUS RF COVERAGE
<br />(30'[9.14m] THROUGH WALLS)
<br />4.04"[102.6mm] (DIA) X 1.17"[29.7mm] (D) I
<br />LOCATION TBD
<br />I I
<br />I I
<br />I I
<br />L------------------------------ J
<br />AS REQUIRED
<br />MAX OF 10 PER QSM
<br />----------------------------i
<br />I i-I
<br />I I
<br />I I I
<br />I � I
<br />LRF2-DCRB-WH
<br />434MHZ WIRELESS i I
<br />DAYLIGHT SENSOR
<br />1.6"[40,6mm] (DIA) X 0.7"[17,8mm] (D)
<br />MAX 10 PER QSM
<br />*DEVICE IS SURFACE -MOUNTED AND i I
<br />BATTERY POWERED, DOES NOT
<br />REQUIRE POWER FEED
<br />REFER TO FLOOR PLAN FOR i I
<br />QUANTITY AND LOCATIONS
<br />I I
<br />TYPICAL OVERRIDE KEYPAD
<br />AS REQUIRED
<br />r---------------------------
<br />I I
<br />I I
<br />I I
<br />I I
<br />I I
<br />I I
<br />I LQ m I
<br />I I
<br />QSWS2-5BRLI-WH
<br />5-BUTTON SCENE
<br />SELECT WITH RAISE/LOWER
<br />(1 GANG US BACKBOX BY OTHERS)
<br />REFER TO FLOOR PLAN FOR
<br />QUANTITY AND LOCATIONS
<br />L--------------------------J
<br />*ALTERNATE DATA -ONLY CABLE: USE APPROVED DATA LINK CABLE (22 AWG [0.5 mm2]
<br />TWISTED/SHIELDED) FROM BELDEN (MODEL # 9461).
<br />**TOTAL LENGTH OF THE QS LINK MUST NOT EXCEED 2,000 ft (600 m).
<br />0 INPUT POWER (NORMAL -EMERGENCY)
<br />❑ INPUT POWER (NORMAL)
<br />2 #12AWG (4 mm2)
<br />O 3 #12AWG (4 1
<br />® 0-1OV SIGNAL: 2 #18AWG (1.0 mm2)
<br />E❑ CAT5E OR BETTER CABLE FOR LUTRON
<br />NETWORK TERMINATED WITH RJ45
<br />CONNECTORS (TO BE PROVIDED BY
<br />OTHERS). 328 ft (100 m) MAXIMUM RUN.
<br />1-WAY RF COMMUNICATION
<br />2-WAY RF COMMUNICATION
<br />2 #18AWG (1.0 mm2)
<br />CONCEPT DRAWING NOTES:
<br />CONTROL SYSTEM DRAWING IS PROVIDED FOR CONCEPTUAL PURPOSES ONLY AND IS NOT
<br />INTENDED FOR CONSTRUCTION. EXACT EQUIPMENT REQUIREMENTS, INCLUDING LOCATIONS AND
<br />QUANTITIES, SHOULD BE VERIFIED IN ACCORDANCE WITH THE MOST UP-TO-DATE
<br />LIGHTING/ELECTRICAL REFLECTED CEILING PLANS, LIGHTING FIXTURE SCHEDULES, PANEL
<br />SCHEDULES, CONTROL INTENT AND SPECIFICATIONS. SHADE EQUIPMENT SHOULD BE VERIFIED IN
<br />ACCORDANCE WITH ARCHITECTURAL PLANS, SPECIFICATIONS AND WINDOW
<br />SCHEDULES/DETAILS.
<br />WIRING LEGEND:
<br />QQ QS CONTROL LINK (SEE WIRE DESCRIPTION BELOW)
<br />.Q QS CONTROL LINK (SEE WIRE DESCRIPTION BELOW)
<br />(CONNECT WIRES 1, 3 AND 4. DO NOT CONNECT WIRE # 2)
<br />QS WIRING AS REQUIRED BY CONTROL LINK LENGTH
<br />(REFER TO QS SMART PANEL POWER SUPPLY WIRING GUIDE FOR SHADE WIRING NOTES):
<br />TOTAL CONTROL
<br />WIRE GAUGE
<br />AVAILABLE FROM LUTRON IN ONE
<br />LINK LENGTH
<br />CABLE:
<br />POWER (TERMINALS 1&2):
<br />LESS THAN 500ft
<br />1 PAIR 18 AWG (1.0 mm0
<br />GRX-CBL-346S (NON -PLENUM)
<br />(152.4 m)
<br />OR
<br />GRX-PCBL-346S (PLENUM)
<br />DATA (TERMINALS 3&4):
<br />1 PAIR 22 AWG (0.5 mm�, TWISTED AND SHIELDED*
<br />POWER (TERMINALS 1&2):
<br />500ft (152.4 m) TO
<br />1 PAIR 12 AWG (4.0 mm�
<br />GRX-CBL-46L (NON -PLENUM)
<br />2,000ft (610 m)**
<br />OR
<br />GRX-PCBL-46L (PLENUM)
<br />DATA (TERMINALS 3&4):
<br />1 PAIR 22 AWG (0.5 ni TWISTED AND SHIELDED*
<br />WIRING NOTES:
<br />QS LINK RULES
<br />THE FOLLOWING LINK RULES MUST BE OBSERVED FOR PROPER OPERATION:
<br />• THIS IS A TOPOLOGY -FREE LINK (T-TAP, HOME -RUN, ETC. IS OK); REFER TO TABLE BELOW FOR
<br />WIRE RUN LIMITS.
<br />• IF WIRED DIFFERENTLY THAN WHAT IS SHOWN, POWER DRAW UNIT REQUIREMENTS NEED TO
<br />BE CONFIRMED; SEE POWER DRAW UNITS (PDUs) SPECIFICATION SHEET INCLUDED IN THIS
<br />SUBMITTAL.
<br />• MAXIMUM OF 512 OUTPUTS (BALLASTS, SHADES, CONTACT CLOSURES, ETC).
<br />• MAXIMUM OF 100 OCCUPANCY SENSORS, 100 DAYLIGHT SENSORS/RADIO SHADOW SENSORS
<br />AND 100 KEYPADS.
<br />• MAXIMUM OF 100 QS DEVICES (SUCH AS A GRAFIK EYEO QS, SEETOUCHO QS KEYPAD, SMART
<br />PANEL POWER SUPPLY [ASPS-Px-10-60], ESN, OR SIVOIAO QS SHADE / DRAPERY DRIVE UNIT).
<br />QUANTUM PROCESSOR COUNTS AS 1 DEVICE PER LINK.
<br />• MAXIMUM OF 100 ZONES - SUCH AS A SIVOIA QS SHADE / DRAPERY DRIVE UNIT, OR A LIGHTING
<br />ZONE ON A GRAFIK EYE QS (DOES NOT APPLY TO QUANTUM SYSTEMS).
<br />• THE 10 OUTPUTS ON A QSPS-Px-10-60 CANNOT EXCEED A COMBINED LENGTH OF 2,000 ft (600 m).
<br />QUANTUM NETWORK
<br />WHEN A LIGHTING MANAGEMENT NETWORK (LMN) IS REQUIRED
<br />TO ENABLE COMMUNICATIONS BETWEEN INDIVIDUAL LIGHT
<br />MANAGEMENT HUBS (LMH) AND BETWEEN LMH AND THE
<br />SYSTEM SERVER/DESKTOP/LAPTOP (Q-MANAGER). THE LMN
<br />REQUIRES A DEDICATED LAN OR VLAN. IT IS THE
<br />RESPONSIBILITY OF THE NETWORK PROVIDER TO ENSURE THE
<br />RELIABILITY AND SECURITY OF THE LMN.
<br />CAT5E OR BETTER ETHERNET CABLE TO BE RUN FOR
<br />DEDICATED LMN TERMINATED WITH RJ45 CONNECTORS
<br />(PROVIDED BY OTHERS). THE NUMBER OF ETHERNET
<br />HOPS/SEGMENTS BETWEEN THE SERVER/DESKTOP/LAPTOP
<br />(Q-MANAGER) AND ANY LMN NODE SHALL NOT EXCEED 6.
<br />TOTAL LENGTH OF ETHERNET CABLE SHALL NOT EXCEED 328
<br />FT (100M) POINT-TO-POINT.
<br />IF LONGER RUNS ARE REQUIRED, MULTI -MODE FIBER OPTIC
<br />CABLE CAN BE USED INSTEAD WITH APPROPRIATE FIBER OPTIC
<br />CONNECTORS (PROVIDED BY OTHERS). CONSULT WITH
<br />NETWORK PROVIDER FOR STANDARD ETHERNET AND FIBER
<br />OPTIC WIRING RULES FOR DISTANCE AND SEPARATION AS
<br />WELL AS FOR PLACEMENT OF SWITCHES, ROUTERS, HUBS, ETC.
<br />FOR MORE INFORMATION REGARDING NETWORK EQUIPMENT
<br />REQUIREMENTS AND NETWORK CONFIGURATION, PLEASE
<br />REFER TO THE QUANTUM LIGHTING MANAGEMENT NETWORK
<br />SPECIFICATION SHEET OR CONTACT LUTRON.
<br />PANEL LINK RULES
<br />THE FOLLOWING LINK RULES MUST BE OBSERVED FOR PROPER OPERATION:
<br />• PANELS ARE DAISY -CHAINED ON ONE OF THE CONFIGURABLE LINKS PER
<br />LUTRON'S DRAWING, HOWEVER THEY DO NOT HAVE TO BE IN THE ORDER
<br />SHOWN.
<br />• DO NOT HOME -RUN OR T-TAP THIS WIRING LINK. ALL CIRCUITS NEED TO BE
<br />LANDED IN THESE PANELS PER LUTRON'S PANEL SCHEDULES.
<br />• THE MAXIMUM WIRE LENGTH OF A PANEL LINK IS 2,000 ft (600 m). A MX-RPTR IS
<br />USED TO EXTEND THE LENGTH OF A LINK ANOTHER 2,000 ft (600 m). A MAXIMUM
<br />OF (3) MX-RPTR'S MAY BE USED PER LINK FOR MAXIMUM LENGTH OF 8,000 ft
<br />(2,430 m) PER LINK.
<br />• IF A PANEL IS MOVED TO ANOTHER LINK, OR THE LOADS ARE NOT WIRED AS
<br />SHOWN IN LUTRON PANEL SCHEDULES, LUTRON MUST BE NOTIFIED. THIS
<br />INFORMATION IS IMPORTANT FOR PROGRAMMING THE SYSTEM.
<br />• UP TO 32 CIRCUIT SELECTORS PER LINK
<br />• UP TO 512 SWITCH LEGS OR ZONES PER LINK
<br />• LT-1 LINK TERMINATORS NEEDED ON EACH END OF THE LINK
<br />LED DIMMING REQUIRES AN EXACT MATCH BETWEEN THE LED ARRAY, DRIVER AND CONTROL.
<br />LUTRON CANNOT GUARANTEE COMPATIBILITY OR PERFORMANCE WITHOUT TESTING THIS
<br />COMBINATION.
<br />TO CONFIRM WHAT PRODUCTS LUTRON HAS AVAILABLE OR WHAT INTERFACES MAY BE
<br />REQUIRED, CALL 1-877-DIM-LED8 OR CHECK LUTRON'S PRODUCT COMPATIBILITY MATRIX ON-LINE
<br />AT WWW.LUTRON.COM/LED.
<br />TO REQUEST THE TESTING OF AN LED PRODUCT BY LUTRON MANUFACTURERS CAN FILL OUT AN
<br />LED EVALUATION REQUEST FORM ON-LINE AT WWW.LUTRON.COM/LED OR CONTACT
<br />LEDS@LUTRON.COM.
<br />LUTRON CAN GUARANTEE COMPATIBILITY AND PERFORMANCE OF LUTRON HI-LUME A -SERIES LED
<br />DRIVERS USED WITH APPROPRIATE LUTRON CONTROLS. THE HI-LUME A -SERIES LED DRIVER CAN
<br />BE USED ON PRODUCTS UNDER 40 WATTS WITH SUITABLE MOUNTING LOCATIONS. PLEASE
<br />REFER TO THE SPECIFICATION SUBMITTAL SHEET FOR FURTHER INFORMATION.
<br />IF USING UNTESTED, NON-LUTRON LED DRIVERS REQUIRING 0-10V CONTROL, PERFORMANCE AND
<br />COMPATIBILITY CANNOT BE GUARANTEED BY LUTRON. PRODUCTS FOLLOWING THE IEC
<br />STANDARD 60929 ARE MORE LIKELY TO PROVIDE ACCEPTABLE PERFORMANCE RESULTS.
<br />DETERMINATION OF RESULT ACCEPTABILITY IS UP TO THE USER'S DISCRETION.
<br />IF USING UNTESTED, NON-LUTRON LED DRIVERS REQUIRING PHASE CONTROL, PERFORMANCE
<br />AND COMPATIBILITY CANNOT BE GUARANTEED BY LUTRON. A -SERIES OR ELV PRODUCTS
<br />PROVIDING HIGH END AND LOW END TRIM ADJUSTMENTS ARE MORE LIKELY TO PROVIDE
<br />ACCEPTABLE PERFORMANCE RESULTS. DETERMINATION OF RESULT ACCEPTABILITY IS UP TO
<br />THE USER'S DISCRETION.
<br />ELECTRICAL DETAILS
<br />SCALE: NOT TO SCALE
<br />E
<br />II �
<br />C&K ARCHITECTS I INTERIORS
<br />architecture • interior design • client services
<br />AAC001629
<br />4221 WEST BOY SCOUT BLVD., SUITE 150
<br />TAMPA, FL 33607-5743
<br />813.884.2000
<br />280 WEST CENTRAL AVE.
<br />WINTER HAVEN, FL33880-2957
<br />863.577.2054
<br />Q J• F f �-
<br />� �\CENSF.•.F�
<br />��.
<br />Q 65083.
<br />5/1 2021 ° W
<br />O STATE OF
<br />F •••••:�C•0R \ 0 P� 'G�
<br />SS/ONAL•��
<br />0
<br />N
<br />s
<br />r
<br />mQ
<br />0
<br />O
<br />z
<br />I.L.
<br />J
<br />J
<br />a
<br />w
<br />N
<br />W
<br />0
<br />W �
<br />Q �O
<br />V_ a
<br />N
<br />0`'
<br />i
<br />V m
<br />LU
<br />m
<br />i
<br />LU
<br />1100
<br />m
<br />Q
<br />C9
<br />M
<br />to
<br />0,
<br />ISSUED FOR;
<br />PERMIT
<br />PROJECT NUMBER
<br />21020
<br />DATE
<br />5.5.21
<br />DRAWING NUMBER
<br />E9III
<br />i
<br />- rr —7-r-FIF r i l � — _ -1 11 1- 1 1 11iu: f i, 1 i 11 11 1 11110 li iri,a. aril, Aflil.E i -,i i i I A i,usi i I I i I I T i
<br />
|