|
THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED,
<br />18"CEIVIENT
<br />PLASTER
<br />I? MIL DRY17-OK
<br />J ir
<br />FXIREME
<br />WINDOW
<br />["ASTENER
<br />1) SEALANT AT
<br />4) SEAL -ANT JOINT
<br />WINDOW BUCK TO
<br />OUTSIDE EDGF Off
<br />MASONRY
<br />WINDOW BLP-"K---
<br />2) SEALANT JOIN I
<br />5) SEALANT FROr,
<br />INSIDE EDGF 0i
<br />WINDOW FRAME
<br />WINDC)W bU(1K
<br />ACROSS WINDOW BUCK
<br />AND EXTEND TO
<br />WINDOW FRAME
<br />MASONRY
<br />ATTACHED
<br />PER CODE
<br />6) Toot ED SFAIANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />OW
<br />CLADDING AND WINDOW
<br />FRAME
<br />3) SEALANT WINDOW F RAME I
<br />WINDOW BUCK ALL THE WAY
<br />AnOUND, INCLUDING Sit I
<br />SCS 0605 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />IAMH,'-)l 11. AND HEAD DETAAL
<br />APPROVED SHEATHING
<br />APPROVED HOUSFWRAP
<br />3TRUCTALATH TWIN TRACK 2,5
<br />314" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAVE
<br />*\r SEALANT SOCKET WITH
<br />TO(A.17D APPROVEO SEALANT
<br />WEATHER
<br />RESISITIVE
<br />BARRIER
<br />-,)WEATHER
<br />tARILY SECURE
<br />VE BARRIER &
<br />WOOD FRAME CONSTR
<br />EXTERIOR SELF -ADHERED FLASHI',
<br />SHEATHING BY LAPPING DOWN --- �
<br />OVER RIM JOIST AND U;
<br />WALL BY 6 IN.
<br />WEATHER
<br />RESISITIVE
<br />BARRIER
<br />SEAL I UPS Of JOIb T8-
<br />UNDER DECKING
<br />(SEE DETAIL WP070)
<br />ED FLASHING
<br />HEAD FLASHING TIE-IN INSTRUXTIONS,
<br />1. Cut, fold up & temporarily secure weather
<br />resistive barrier above header to allow for
<br />I'lashing installation
<br />2. Sell -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold weathef resistive t)arner back over head
<br />flashing and seal with tape
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER wpol
<br />EXTERIORSHEATHING
<br />REFER TO TECHNICAL
<br />L.ETTER ON CHEMICAL
<br />COMPATIBILIVe
<br />SELF -ADHERED FLASHING
<br />00 NOT F LASH OVER
<br />BOTTOM NAILING
<br />r!ANGE
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />NAILING FLANGE
<br />ISCS 06 02 WINDOW FIN INTERFACE WITH ISELF-ADHERED FLASHING
<br />EXTRUDED SHOULDER DECK JOIST
<br />SELF-ADHFRF0 FLASI-1046
<br />T
<br />WP04
<br />AM
<br />WP,07
<br />2x FRAMEWALL--____
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS TILE FINISH
<br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO
<br />PER THE FBC RESIDENTIAL 7TH EDITION (2020)
<br />Detail Iristiuctions
<br />Refer to the number marked as (�) in each detail that corresponds to the
<br />numbered items In the list of instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on dernand,
<br />embedded in Me adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release papei per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (13" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accoidingly to
<br />fit tight to corner
<br />8. Mechanically fastpin as necessary
<br />112" DIJROCK
<br />V-4" PER PLAN - -----
<br />V-0" PER PLAN
<br />SLOPE
<br />80 CIVILI -
<br />4" OR 8" CMU
<br />(PER SEAT DEPTH)
<br />- : -_a -_ - -,. ;.. .
<br />FILL WITH GROUT
<br />SLOPED MUD BED - :\"a, a
<br />7__..
<br />VINYL SHOWER PAN
<br />4
<br />SLOPF
<br />SHOWER SEAT
<br />4t,Al HER HE.61,S I WE
<br />BARRIER
<br />SL-LF-ADHERED FLASHING
<br />EXTERIOFDOOR WITH DECK - SECTION A
<br />EXTERIOR SHEATHIW;
<br />3141%1" BEAD OF G(NSTR
<br />ADHE SIVE TO BEA -PLIED UNUE. R
<br />1HPIESHOLD OF D(�OR AND RETURN
<br />UP JAMB 6". USE LI )UID NAIL BRAND
<br />OR EQUAL WEATH� ]R PROOF CAUL KIN(l,
<br />SECTION -A fSF E EA. 1 11. WP02)
<br />4
<br />SELF -ADHERED FLA 3HING -
<br />SEAL TOPS OF J )IST
<br />UNDER DECK IN;
<br />(SEE DETAIL Wl-, 11)
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />SFLF-ADHER
<br />SELF -ADHERED FLASHING
<br />OUTSIDF CORNER
<br />(n
<br />>
<br />C0
<br />z z
<br />.5 ! :5
<br />Cr
<br />LU LLi
<br />0- a-
<br />I.- U)
<br />U)
<br />LU
<br />IL)
<br />LU
<br />cr
<br />Cr
<br />LLJ
<br />Lid
<br />0
<br />WF1 1
<br />'HING REQUIREMENTS
<br />--WINDOW UNI I FLAS
<br />DOOR ROUGH OPENING
<br />SLOPE
<br />0.3 in: 12.0 in R703.1 Generai. Exterior walls shall provide the bUliding with a weather -resistant extc-o"ior wall envelope. The exterior wall envelope shall
<br />(0. 6 cm : 30.5 cm) include flashing as described it) Section R7034
<br />ADHESIVETO BE APPLIED UNDER SFLF-ADHERED FLASHING
<br />THRESHOLD OF DOOR AND
<br />RETURN UP JAMB 6". USE LIQUID EXTERIOR R703.1.1 Water resistance The exterior wall envelope s-iall be designed and constructed in a manner that prevents the accuMLIlation of water
<br />NAIL BRAND OR E00At I - 1 F �
<br />PROOF (,AL)L KING --CFMI. FIN. within the wall assep*y by providing a water-resistant barrier behind the exterioi cladding as required by Section R703,2 arid a means of
<br />SELF -ADHERED FLASHING BUILDING PAPER draining to the exterior water that penetrates the exterior cladding.
<br />WIRE LATH R703.2 Water- fesisti ve barrier One layer of No 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or other
<br />SUBFLOOR approved water -resistive barrier shall be applied over Studs Or sheathing of all exterior walls No. 15 asphalt felt shall be applied horizontally,
<br />with the upper- layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6 Inches Other
<br />approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions The No 15 asphalt
<br />felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and building
<br />RIM JOIST
<br />appendages in a manner, to meet the requirements of the exterior wall envelope as described in Section R703.1
<br />R703.7.3 Water -resistive barriers Water -resistive barrjer3 sha,!l be installed as iequired in Section R703.2 arid, where applied overwood-based
<br />sheathing, shzill includu a vvater-resistive vapor-perineable barrier with a perforniance at least equivalent to two layers of Grade D paper. Thc.�
<br />v- A 2 , )
<br />2 individual layers shall be installed indepencle-atly such that each layer provides a separate contillUOUS, plane and any flashing (installed in
<br />accordance with Section R703.4) intended to drain to the water -resistive barrier i,s directed between the layers.
<br />SELF -ADHERED FLASHING
<br />Exception: 'VVhere the %Aiater-resisfive barrier, that is applied over wood-ba�sed sheathing has a water resistance
<br />WPO)12 CEMT. FINISH SILL,�'POTSHELF/ CHIMNEY SHOULDER WP03 equal to oi gfeater than that of 60-ininute Grade D paper and is separated frorn the stucco by an intervening,
<br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED A-SPHALT substantially no n water -absorbing layer, or designed drainage space.
<br />INSI Ai I Sf I �_ AI)Hf� NEEDED IN CORNERS ASPHALT ADHESIVE: ADHESIVE
<br />FLASH�NG JAMB & HEAD THROUGH SELF -ADHERED R703,4 Flashing. ApprGved metal flashirg, vinyl flashing self -adhered membranes and mechamcally attached flexible flashing shall be applied
<br />FLASHING. SEE FLASHING [----SELF-ADHERED FLASH�NG----
<br />FLANGED WINDOW shingle -fashion or In accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Flutd-applied membranes
<br />i�SEE DETAIL WIP01)
<br />L
<br />RN
<br />F_A
<br />ERS
<br />DHER,ED
<br />7 used as flashing shall be applied in accordance with the manufaCtUrer's instructions. All flashing shall be applied in a manner to prevent the
<br />SCORED entry of water into the wall cavity or penetration of water to the building structural framing components.
<br />RELEASE PAPER
<br />Self -adhered n-lenibraneS Used as flashing shall comply Nith AAMA 711 - All exterior fenestration products shall be sealed at the juncture with
<br />�EiOeW4E PCX DN(l SCICke the building wa�l with a sealant complying with AAMA 800 or ASTIV C920 Class 25 Grade NS or greater for proper joint expansion and
<br />Rf*, t F ASE PAPE R rC) I. XK)SL
<br />EXT END A M1141 MUM 0
<br />VERTICALLYFRCM AC101i AS SHCWN) contraction, ASTMC 128 1, AA%1A 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as
<br />BOTTOM ()I: flashing in exterior wal)s shaIl comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish Approved flashings
<br />I HIRE SH(X.
<br />shall be installed at the fodovviing locations�
<br />1. 1I.Exterior window and door openings. Flashing at exterior window arid door, openings shall extend to the surface of the exterior wall
<br />finish or to the water -res;stive bat rier complyingwith Section 703,2 for subsequent drainage. Mechanically attached flexible flashings
<br />shallcomply with AAMA 71�2. Flashing at exterior window and door opemngs shall be installed in accordance with one or n1ore of the
<br />followl-Ig
<br />5 1.1 The fenestration manufacturer's installation and flashing InStl`1.10011S, of- for applications not, addressed in the fenestration
<br />manufacturer's in accordance with the fiashing manufacturer's instructions. Where flashing instructions or details are
<br />4,
<br />n�-t provided, pan flashing shah be installed at the Sill of exterior window arid door openings. Pan flashing 5hah be Sealed or
<br />6 sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for subsequent
<br />drainage Openings using pat) flashing shall incorporate flashing or protection at the head and sides.
<br />2' 7 )
<br />1.2 1.2 In accordance with the flashing design or method of a registered design professional -
<br />SELF -ADHERED FLASHING 1�3 1 �1 In accordance with other approved methods.
<br />W'P05 INSIDE CORNER WP06 1.4 In accordancewith FMAjAAMA 100, FMA/ AAFAA 200, FNIA/WDMA 250, FMA/AAMAi WDMA 300 or FMA/AAMA/WDMA 400.
<br />2. 2 At the intersection of chinineys or other masonry construction with frame or stucco walls. with pfojecting hps on both sides Under
<br />stucco copings.
<br />2
<br />4
<br />6
<br />Ground 3.3 Under and at the ends of masonry, wood or wetai copings and sills,
<br />4.4.Coritinuously above all projecting wood trim.
<br />5. 5.Where extet iot porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6.6.At wall and roof intorsections.
<br />7. 7.At built-in QUtters.
<br />Water Resistant Barrier
<br />1F-ADHERED FLASHING
<br />�TCH
<br />flERED FI.ASHING
<br />WP08
<br />PLASTER STOP
<br />CONTINUOUS BACKER -
<br />k0D & SEALANT
<br />Lath
<br />Sheathing
<br />Stucco
<br />FOUNDATION WEEP SCREED
<br />T FNI IP (h: SAF
<br />+ DRAiNACit 1?LANL,1VHh
<br />BOND B13EAK WIRB
<br />SF LAIH
<br />WRAP DID WRB ONTO
<br />THE VERTICAi.
<br />SURFACE To TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />3-1 Q" INCH FLANGE
<br />'THIS GAP IS A RESULT OIF
<br />NAT(MAL $IIRINKAG('
<br />DO NOT SEAL,
<br />ORIP z�,� 1,EED PLAST'C'
<br />ACCESSORY
<br />SOFFIT/CANTILEVER
<br />LEGEND
<br />I L I AD� ILRLD I LASHiNG (SAF) -0 ------- 0-
<br />BARRIER (WRB�
<br />UHAiNAUE PLANE (DP) WEATHER RE515TANT
<br />BOND BREAK WEAniER RESISTANI BARRIER
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHiNG.'00,8' PI YWOOD, DENSGLASS
<br />_A
<br />kSTER STOP
<br />�Q I INLIOUS BA(*ER 1401"�
<br />EALANT
<br />VENTITI01JS FINISH
<br />"TURAL FRAMING
<br />'TUnALSHE
<br />,ATHINn
<br />OF SAF
<br />JAGE PLANE WRR
<br />BREAK WRB
<br />TH
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATER\PROOFING METHODS TO BE USED.
<br />--- --- - 7/8"Cernent Plaslei
<br />�n accordance wi,h
<br />ASI MC926
<br />F Pit backed metal
<br />.............
<br />lathe in accordance
<br />......... . .
<br />..... .....
<br />williASTMC1063
<br />build ng Papei
<br />7116"O.S.B.
<br />sheathing
<br />Flashing
<br />------- Wee) Soced
<br />Installed As Per
<br />Manufact. Specs.
<br />Maint3in
<br />Bolto-T� of
<br />Weep Screed
<br />1 1/2" to 2"
<br />Above Roof
<br />Sheciihing
<br />Cement Plaster
<br />in accordance
<br />with ASTI,11C,926 a
<br />ovet wooll 2nd
<br />flool L
<br />Cement
<br />Plaster
<br />over block
<br />1 St flool,
<br />7/8" Cernent Plaster
<br />in accoidance with
<br />AS T MC926
<br />FPlt backed metail
<br />lathe in accordance
<br />with ASTIVIC 1063
<br />Building Paper
<br />/1`16" O.S.H
<br />qhpa ii I
<br />\11C
<br />0
<br />tea tido
<br />C00AR -
<br />P
<br />1 'o
<br />Z
<br />Weep Screed
<br />Installed As Per
<br />MallUfact 1,33pecs.
<br />1,12" Cementitious
<br />Decotative Finish
<br />All Inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede ot slifri.
<br />all
<br />caulk for
<br />.......
<br />Note:
<br />building and metal lath musi be
<br />Th(- riapet
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />qCAIF-N0TT0SCAI_F
<br />40
<br />(1)
<br />U)
<br />-0
<br />(1)
<br />:>
<br />0
<br />_0
<br />C-
<br />0
<br />C�L
<br />0
<br />,
<br />CL
<br />U)
<br />9__
<br />:3
<br />C0
<br />-M
<br />Cf)
<br />(3)
<br />-70
<br />0
<br />C)
<br />-0
<br />C:)
<br />_0
<br />LL_
<br />b
<br />>
<br />E
<br />U)
<br />Cl
<br />Cn
<br />Cn
<br />(3)
<br />C_
<br />>
<br />0
<br />Go
<br /><
<br />111
<br />0
<br />0
<br />0
<br />U)
<br />UJ
<br /><
<br />z
<br />SHEET NO.
<br />WP1.0
<br />
|