6614 Back Forty Lp - Laserfiche WebLink

Browse Search

STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON FIBER CEMENT SIDING 2- LAYERS OF WATER RESISTIVE BARRIER WALL SHEATHING PER PLAN PER ELEVATIONS COMPLYING WITH ASTM E2556, TYPE 1 (TYP)----- STUCCO ON FRAME - 7/8" 3-COAT SAND WALL SHEATHING PER PLAN ----- WALL SHEATHING PER PL.AN---- FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER SHINGLE WATER RESISTIVE SHINGLE WATER RESISTIVE BARRIER OVER FLASHING --------- BARRIER OVER WEEP SCREED COMPLYING WITH ASTM E2556, TYPE 1 (TYP) WEEP SCREED SHINGLE WATER RESISTIVE STARTER BARRIER OVER WEEP SCREED )/F HOLD 1/4" AIR GAP HOLD 1/4" AIR GAP BETWEEN WEEP WEEP SCREED BETWEEN SIDING AND SCREED AND FLASHING 'o HOLD 1/4" AIR GAP FLASHING COUNTER FLASHING BETWEEN WEEP COUNTER FLASHING ----------- SCREED AND FLASHING CCNT SELF ADHERED FLASHING TO CONT SELF ADHERED FLASHING TO LAP FLASHING AND TURN 3" UP WALL CONT SELF ADHERED FLASHING TO LAP FLASHING AND TURN 3" UP WALL LAP FLASHING AND TURN 3" UP WALL FLASHING FLASHING PT lX10 BLOCKING lo 11 PT 1X BLOCKING PT lX10 BLOCKING-----� CONT SELF ADHERED FLASHING COUNTER FLASHING CONT SELF ADHERED FLASHING TURN 3" UP BLOCKING TURN 3" UP BLOCKING 00 PAN FLASHING 6" MIN loll MIN CEMENT MORTAR CEMENT MORTAR ROOF UNDERLAYMENT TO TILE ROOF PER SPECS ROOF UNDERLAYMENT TO TURN UP BLOCKING MIN 6" CONT SELF ADHERED FLASHING TILE ROOF PER SPECS ................... ROOF UNDERLAYMENT ro TURN UP BLOCKING MIN 8" ROOF SHEATHING TURN 3" UP BLOCKING TILE ROOF PER SPECS-----______ TURN UP BLOCKING MIN 8" ROOF SHEATHING PER PLAN---------- PER PLAN---------- 2X NAILER SECURELY FASTENED TO DECK - ROOF SHEATHING NOTE: PER PLAN ---------- ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL HEAD WALL I RAKE WALL I %a VVI-%L.L- - Ljr%FxFxL-L- I IL-L- I %-.# Q I U% .. f %-"# \a I - " '- 311=1 1-011 1 WP16 L A311= 1 1-011 Qmwlli NGLE ROOF PER SPECS UNDERLAYMENT TO SHINGLE OVER DRIP EDGE ROOF SHEATHING PER PLAN DRIP EDGE 2X6 SUB FASCIA SELF ADHERED WRB TO SHINGLE OVER WRB ON WALL BELOW ALUMINUM BRAKE METAL WRAP CONT BACKER ROD AND SEALANT STUCCO'J'MOULDING HOLD OFF BRAKE METAL 1/4" MIN STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP) WALL SHEATHING PER PLAN WP18 WALL SHEATHING PER P FIBER CEMENT SIDING PER ELEVATIONS SHINGLE WATER RESISTIVE BARRIER OVER FLASHING - STARTER STRIP - HOLD 1/4" AIR GAP BETWEEN SIDING AND FLASHING CONT SELF ADHtiRED FLASHING TO LAP FLASHING AND TURN 3" UP WALL--,,,, PT 1X BLOCKING ----- COUNTER FLASHING PAN FLASHING 6" ROOF UNDERLAYMENT TO TURN UP BLOCKING MIN 6"--, CONT SELF ADHERED FLASHING TURN 3" UP BLOCKING TILE ROOF PER SPECS--- HEAD WALL 2X NAILER SECURELY FASTENED TO DECK - ROOF SHEATHING PER PLAN ---------- FLASHING REQUIREMENTS R730.1 GENERAL. EXTERIOR WALLS SHALL PROVIDE THE BUILDING WITH A WEATHER -RESISTANT EXTERIOR WALL ENVELOPE. THE EXTERIOR WALL ENVELOPE SHALL INCLUDE FLASHING AS DESCRIBED IN SECTION R703.4. R703.1 .1 WATER RESISTANCE. THE EXTERIOR WALL ENVELOPE SHALL BE DIMENSIONED AND CONSTRUCTED IN A MANNER THAT PREVENTS THE ACCUMULATION OF WATER WITHIN THE WALL ASSEMBLY BY PROVIDING A WATER-RESISTANT BARRIER BEHIND THE EXTERIOR CLADDING AS REQUIRED BY SECTION R703.2 AND A MEANS OF DRAINING TO THE EXTERIOR WATER THAT PENETRATES THE EXTERIOR CLADDING. R7C3.2 WATER RESISTIVE BARRIER. ONE LAYER OF NO,15 ASPHALT FELT, FREE FROM HOLES, COMPLY WITH ASTM D226 FOR TYPE 1 FELT OR OTHER APPROVED WATER -RESISTIVE BARRIER SHALL BE APPLIED OVER STUDS OR SHEATHING OF ALL EXTERIOR WALLS NO. 15 ASPHALT FELT SHALL BE APPLIED HORIZONTALLY, WITH THE UPPER LAYER LAPPED OVER THE LOWER LAYER NOT LESS THAN 2 INCHES. WHERE JOINTS OCCUR, FELT SHALL BE LAPPED NOT LESS THAN 6 INCHES. OTHER APPROVED MATERIALS SHALL BE INSTALLED IN ACCORDANCE WITH THE WATER -RESISTIVE BARRIER MANUFACTURER'S INSTALLATION INSTRUCTIONS. THE NO.15 ASPHALT FELT OR OTHER APPROVED WATER -RESISTIVE BARRIER MATERIAL SHALL BE CONTINUOUS TO THE TOP OF WALLS AND TERMINATED AT PENETRATIONS AND BUILDING APPENDAGES IN A MANNER TO MEET THE REQUIREMENTS OF THE EXTERIOR WALL ENVELOPE AS DESCRIBED IN SECTION R703.1. R703.7.3 WATER -RESISTIVE BARRIERS WATER -RESISTIVE BARRIERS SHALL BE INSTALLED AS REQUIRED IN SECTION R703.2 AND, WHERE APPLIED OVER WOOD -BASED SHEATHING, SHALL INCLUDE A WATER -RESISTIVE VAPOR -PERMEABLE BARRIER WITH A PERFORMANCE AT LEAST EQUIVALENT TO TWO LAYERS OF GRADE D PAPER. THE INDIVIDUAL LAYERS SHALL BE INSTALLED INDEPENDENTLY SUCH THAT EACH LAYER PROVIDES A SEPARATE CONTINUOUS PLANE AND ANY FLASHING (INSTALLED IN ACCORDANCE WITH SECTION R703.4) INTENDED TO DRAIN TO THE WATER -RESISTIVE BARRIER IS DIRECTED BETWEEN THE LAYERS. EXCEPTION: WHERE THE WATER -RESISTIVE BARRIER THAT IS APPLIED OVER WOOD -BASED SHEATHING HAS A WATER RESISTANCE EQUAL TO OR GREATER THAN THAT OF 60-MINUTE GRADE D PAPER AND IS SEPARATED FROM THE STUCCO BY AN INTERVENING SUBSTANTIALLY NON -WATER -ABSORBING LAYER OR DESIGNED DRAINAGE SPACE. R703.4 FLASHING. APPROVED METAL FLASHING, VINYL FLASHING, SELF -ADHERED MEMBRANES AND MECHANICALLY ATTACHED FLEXIBLE FLASHING SHALL BE APPLIED SHINGLE -FASHION OR IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. METAL FLASHING SHALL BE CORROSION RESISTANT. FLUID -APPLIED MEMBRANES USED AS FLASHING SHALL BE APPLIED IN ACCORDANCE WITH THE MANUFACTURER'S RAKE WALL INSTRUCTIONS. ALL FLASHING SHALL BE APPLIED IN A MANNER TO PREVENT THE ENTRY OF WATER INTO THE WALL CAVITY OR PENETRATION OF WATER TO THE WP17 BUILDING STRUCTURAL FRAMING COMPONENTS. SELF -ADHERED MEMBRANES USED AS FLASHING SHALL COMPLY WITH MMA 711. ALL EXTERIOR FENESTRATION PRODUCTS SHALL BE SEALED AT THE JUNCTURE WITH THE BUILDING WALL WITH A SEALANT COMPLYING WITH AAMA 800 OR ASTM C920 CLASS 25 GRADE NS OR GREATER FOR PROPER JOINT EXPANSION AND CONTRACTION, ASTMC1281, MMA 812, OR OTHER APPROVED STANDARD AS APPROPRIATE FOR THE TYPE OF SEALANT. FLLJID-APPLIED MEMBRANES USED AS FLASHING IN EXTERIOR WALLS SHALL COMPLY WITH AAMA 714. THE FLASHING SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH. APPROVED FLASHINGS SHALL BE INSTALLED AT THE FOLLOWING LOCATIONS: 1 . 1. EXTERIOR WINDOW AND DOOR OPENINGS. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER -RESISTIVE BARRIER COMPLYING WITH SECTION 703.2 FOR SUBSEQUENT DRAINAGE. MECHANICALLY ATTACHED FLEXIBLE FLASHINGS SHALL COMPLY WITH MMA 712. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL BE INSTALLED IN ACCORDANCE WITH ONE OR MORE OF THE FOLLOWING: 1.1 THE FENESTRATION MANUFACTURER'S INSTALLATION AND FLASHING INSTRUCTIONS, OR FOR APPLICATIONS NOT ADDRESSED IN THE FENESTRATION MANUFACTURER'S INSTRUCTIONS, IN ACCORDANCE WITH THE FLASHING MANUFACTURER'S INSTRUCTIONS. WHERE FLASHING INSTRUCTIONS OR DETAILS ARE NOT PROVIDED, PLAN FLASHING SHALL BE INSTALLED AT THE SILL OF EXTERIOR WINDOW AND DOOR OPENINGS. PAN FLASHING SHALL BE SEALED OR SLOPED IN SUCH A MANNER AS TO DIRECT WATER TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER RESISTIVE BARRIER FOR SUBSEQUENT DRAINAGE. OPENINGS USING PAN FLASHING SHALL INCORPORATE FLASHING OR PROTECTION AT THE HEAD AND SIDES. 1.2 IN ACCORDANCE WITH THE FLASHING DESIGN OR METHOD OF A REGISTERED DESIGN PROFESSIONAL. 1.3 IN ACCORDANCE WITH THE OTHER APPROVED METHODS. 1.4 IN ACCORDANCE WITH FMA/AAMA 100, FMA/AAMA 200, FMA/WDMA 250, FMA/AAMA/WDMA 300 OR FMA/AAMA/WDMA 400. 2.2 AT THE INTERSECTION OF CHIMNEYS OR OTHER MASONRY CONSTRUCTION WITH FRAME OR STUCCO WALLS, WITH PROJECTING LIPS ON BOTH SIDES UNDER STUCCO COPINGS. 3.3 UNDER AND AT THE ENDS OF MASONRY, WOOD OR METAL COPINGS AND SILLS. 4.4 CONTINUOUSLY ABOVE ALL PROJECTING WOOD TRIM. 5.5 WHERE EXTERIOR PORCHES, DECKS OR STAIRS ATTACH TO A WALL OR FLOOR ASSEMBLY OF WOOD -FRAME CONSTRUCTION. 6.6 AT WALL AND ROOF INTERSECTIONS. 7.7 AT BUILT-IN GUTTERS. THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL FLASHING AND WATERPROOFING METHODS TO BE USED. . \St 6 so . \lea C? S $01 a mv(\ C/) > 0 (D c: 0 0 " CL cn (D r-- L- o 25- —0 a cu .0 -6-4 cu u- %+- 0 cu > cn E'a) cu 0 ca- co -0 .0 c: — -0� c/) z w mi V m� cu 0 0 L. LLI CL U) co 0 CD- 0 CD C/) cu m 1:1 SHEET NO. WP 2A