|
EXISTING FLOOR PLAN
<br />DIMENSIONS:
<br />GENERAL CONTRACTOR TO FIELD VARIFY
<br />LOCATION OF PROPOSED NEW WALLS
<br />EQUIPMENT AND PLACEMENT, PRIOR
<br />TO START OF WORK. DIMENSION DISCREPENCY
<br />OR EQUIPMENT SHALL BE BROUGHT
<br />TO ARCHITECT'S ATTENTION FOR CORRECTION.
<br />SPRINKLER SYSTEM:
<br />THE EXISTING SPRINKLER SYSTEM TO REMAIN, AND
<br />REQUIRED CHANGES SHALL BE PROVIDED BY SPRINKLER
<br />SUBCONTRACTOR FOR DESIGN ALTERATIONS DESIGN APPROVAL.
<br />DESIGNALTERATIONS, SHOP DRAWING, AND CALULATIONS TO BE UNDER
<br />A SEPARATE PERMIT .
<br />A FL STATE LICENSED FIRE SPRINKLER CONTRACTOR SHALL APPLY FOR
<br />AND OBTAIN A FIRE SPRINKLER PERMIT THROUGH
<br />ANY WORK SHALL BEGIN.
<br />4
<br />"I
<br />It
<br />ElliACT
<br />HALL
<br />; UAI
<br />7��
<br />EXISTING 6 TON RTU
<br />Q
<br />EXISTING SPIRAL DUCT'
<br />J
<br />I
<br />DINING
<br />OPEN CEILING
<br />9
<br />CLG Q CLG Q E CLG
<br />EXISTING REFLECTIVE
<br />CEILING PLAN
<br />ACT
<br />A
<br />E3
<br />m
<br />KITCHEN
<br />YPBD. CEII
<br />X
<br />BUILDING DEMOLITION LEGEND
<br />SYMBOL DESCRIPTION
<br />LOWER PORTION OF WALL IS TO BE REMOVED.
<br />01 UPPER PORTION OF WALL TO REMAIN MAKING A SOFFIT
<br />BETWEEN OPEN CEILING AND ACT IN KITCHEN
<br />02 WALL TO BE REMOVED
<br />03 COUNTER TO BE REMOVED
<br />04 REMOVE FLOORING.
<br />CLEAN AND PREP FOR NEW FLOORING
<br />05 REMOVE WALL FINISH. CLEAN AND PREP FOR NEW FINISH
<br />REMOVE DRINKING FOUNTIAN
<br />06 PLUG AND CAP.
<br />07 REMOVE DOOR
<br />pg REMOVE BENCH AND SOFFIT ABOVE
<br />09 REMOVE HAND SINK
<br />PLUG AND CAP.
<br />10 AREA FOR NEW ACT FOR NEW MEN'S RESTROOM
<br />0--
<br />AREA FOR NEW ACT FOR NEW WOMEN'S RESTROOM
<br />0-
<br />2 RELOCATE SINK TO MEET ADA REQUIREMENTS IF NEEDED. FIELD VERIFY
<br />0-
<br />3 REUSE EXISTING DOOR. FIELD VERIFY CONDITION
<br />14 PREP AREA TILE TO REMAIN. CLEAN, REPAIR, AND INFILL AS NEEDED
<br />MATCH EXISTING
<br />ONTRACTOR NOTE:
<br />HVAC DUCTWORK AND DIFFUSERS TO REMAIN -CLEAN AND REPAIR
<br />ELECTRICAL LEGEND
<br />NL OUTLET
<br />18 ABOVE FIN. FLR.
<br />&42"
<br />42" A.F.F. WALL RECPI
<br />HEIGHT AFF VARIFY - SEE PLANS
<br />@CLG
<br />CEILING MNT DUPLEX
<br />&GFI
<br />GRND FAULT INTERUPT
<br />@0220V
<br />18" A.F.F. 220V RECPj
<br />EQUIPT. VARIES - SEE PLANS
<br />FOUR PLEX
<br />WALL OUTLET
<br />I= FL
<br />FLOOR RECPT
<br />DIRECT CONNECTION
<br />J
<br />JUNCTION FOR LIGHTS
<br />DISCONNECT
<br />O
<br />ELECTRICAL PANEL
<br />HVAC LEGEND
<br />A/C DIFFUSER
<br />ro-�
<br />CLG. VENT
<br />A/C RETURN AIR
<br />R
<br />CLG. GRILL
<br />®
<br />EXHAUST FAN
<br />H VAC NOTE:
<br />ALL EXISTING HVAC SYSTEMS TO REMAIN, AS IS, UNLESS NOTED
<br />OTHERWISE ON DEMOLITIONS PLANS, AND / OR ALTERATION PLANS.
<br />FIRE PROTECTION
<br />EXISTING
<br />SPRINKLER HEAD
<br />NEW OR RELOCATED
<br />®
<br />SPRINKLER HEAD
<br />F.E.
<br />EXISTING
<br />>O
<br />FIRE-EXTINGUISHER
<br />ELECTRICAL LEGEND
<br />SYMBOL
<br />DESCRIPTION
<br />EXISTING BULBS TO REPLACED WITH NEW LED
<br />2'X4' LED LAY -IN W/ ACRYLIC LENSES
<br />KITCHEN
<br />LXIS-HNG �13ULBS 10 RLPLACED WITH NEW LED)
<br />2'X4' LED LAY -IN W/ TROFFER LENSES
<br />Al
<br />PARABOLIC LED
<br />CUSTOMER AREA RESTROOMS
<br />EXISTING
<br />C1®
<br />CEILING MOUNTED RECESSED DOWNLIGHT
<br />0 Q
<br />EXISTING
<br />El 0
<br />EMERGENCY LIGHT
<br />EXISTING
<br />00
<br />EMERGENCY LIGHT
<br />E3
<br />& EXIT LIGHT COMBO
<br />NEW
<br />F o
<br />CEILING MOUNTED RECESSED DOWNLIGHT
<br />RL38/CTR1902 WHITE/A19 MAX 10OW LAMP
<br />NEW TRACK AND FIXTURES
<br />CTL2120/PAR 20 MAX 50W LAMPS
<br />ADD TO NEW POWER CIRCUIT
<br />GENERAL NOTES -
<br />DIVISION 1 GENERAL REQUIREMENTS
<br />1. THE INTENT OF THESE DOCUMENTS IS TO PROVIDE FOR THE CONSTRUCTION OF THIS
<br />PROJECT, COMPLETE AND FUNCTIONAL IN ALL RESPECTS. THE CONTRACTOR SHALL BE
<br />RESPONSIBLE FOR THIS RESULT. THE OMISSION OF EXPRESS REFERENCE TO WORK
<br />NECESSARY AND REASONABLY INCIDENTAL FOR THE COMPLETE CONSTRUCTION OF THE
<br />PROJECT SHALL NOT BE CONSTRUED AS RELEASING THE CONTRACTOR FROM HIS
<br />RESPONSIBILITIES.
<br />2. THE CONTRACTOR SHALL VERIFY ALL EXISTING DIMENSIONS, CLEARANCES AND
<br />CONDITIONS TO THE ARCHITECT PRIOR TO COMMENCEMENT OF WORK. FAILURE TO DO SO
<br />CONSTITUTES ACCEPTANCE AND RESPONSIBILITY FOR ALL EXISTING CONDITIONS. THE
<br />CONTRACTOR WILL NOT BE ALLOWED ADJUSTMENTS IN THE TIME OR MONEY REQUIRED TO
<br />RECTIFY THE SITUATION.
<br />3. DO NOT SCALE DRAWINGS. GIVEN DIMENSIONS SHALL GOVERN. LARGE SCALE DRAWINGS
<br />SHALL GOVERN OVER SMALL SCALE DRAWINGS.
<br />4. THE CONTRACTOR SHALL SUBMIT SHOP DRAWINGS OF ALL PURCHASED, FABRICATED AND
<br />FINISHED ITEMS FOR REVIEW BE THE ARCHITECT UNLESS WAIVED BY THE SAME.
<br />5. ALL EQUIPMENT, MATERIALS AND ARTICLES INCORPORATED INTO THE PROJECT SHALL BE
<br />NEW AND UNDAMAGED. ALL WORKMANSHIP SHALL BE WITHIN INDUSTRY STANDARDS.
<br />6. THE CONTRACTOR SHALL BE RESPONSIBLE FOR REPAIR AND REPLACEMENT OF DAMAGE
<br />TO AREAS CAUSED BY HIS WORK AT NO ADDITIONAL COST TO THE OWNER.
<br />7. THE CONTRACTOR SHALL BE RESPONSIBLE FOR SAFETY CONDITIONS RELATING TO JOB
<br />CONSTRUCTION INCLUDING A SAFE ENVIRONMENT FOR OCCUPANTS OF AREAS ADJACENT
<br />TO THE WORK AREA.
<br />8. THE CONTRACTOR SHALL PAY ALL FEES FOR PERMITS NECESSARY FOR PROPER
<br />COMPLETION OF WORK, UNLESS NOTED OTHERWISE.
<br />9. SHOULD THE CONTRACTOR OBSERVE ERRORS, DISCREPANCIES OR OMISSIONS IN THE
<br />CONTRACT DOCUMENTS, HE SHALL PROMPTLY NOTIFY THE ARCHITECT REQUESTING
<br />CLARIFICATION. THE CONTRACTOR SHALL NOT PROCEED WITH WORK AFFECTED BY SUCH
<br />ERRORS, DISCREPANCIES OR OMISSIONS WITHOUT RECEIVING CLARIFICATIONS.
<br />ADJUSTMENTS INVOLVING SUCH CONDITIONS MADE BY THE CONTRACTOR WITHOUT PRIOR
<br />CLARIFICATION BY THE ARCHITECT, SHALL BE AT THE CONTRACTOR'S OWN RISK.
<br />COMPLICATIONS ARISING FROM PROCEEDING WITHOUT CLARIFICATION SHALL BE
<br />RESOLVED AT THE CONTRACTOR'S EXPENSE.
<br />0. ALL WORK PERFORMED ON THIS PROJECT SHALL COMPLY WITH ALL APPLICABLE LOCAL,
<br />STATE AND NATIONAL CODES, LAWS AND ORDINANCES.
<br />1. ANYTHING IN THE CONTRACT DOCUMENTS NOT WITHSTANDING, THE CONTRACTOR
<br />ACCEPTS THE RESPONSIBILITY OF CONSTRUCTING A WATERTIGHT, WEATHER TIGHT
<br />PROJECT.
<br />2. CONTRACTOR SHALL COORDINATE LOCATION OF ALL NEW ROOF MOUNTED EQUIPMENT
<br />WITH OWNER PRIOR TO INSTALL. CENTER EQUIPMENT OVER BEAM OR COLUMN UNLESS
<br />DIRECTED OTHERWISE BY OWNER.
<br />3. CONTRACTOR SHALL PROVIDE 2x BLOCKING AT ALL WALL MOUNTED EQUIPMENT OR
<br />ACCESSORIES.
<br />4. ALL SIGNS, INCLUDING WINDOW SIGNS, TO BE SUBMITTED FOR REVIEW AND APPROVAL
<br />UNDER SEPARATE PERMIT BY OWNER/CONTRACTOR.
<br />5. ALL ANGLES AT 45' OR 90' UNLESS OTHERWISE NOTED.
<br />DIVISION 2 DEMOLITION; HAZARDOUS MATERIALS
<br />THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL DEMOLITION REQUIRED TO ALLOW
<br />FOR ALL PROPOSED NEW WORK.
<br />PATCH, REPAIR, REPLACE AND FINISH ANY FLOOR, WALL OR CEILING TO MATCH ADJACENT
<br />1. AREAS WHERE DEMOLITION HAS BEEN REQUIRED.
<br />PROVIDE PROPER SHORING AND DISCONNECTION OF ALL UTILITIES PRIOR TO DEMOLITION.
<br />2• THE CONTRACTOR SHALL BE RESPONSIBLE FOR KEEPING THE SITE FREE OF DEBRIS.
<br />THE CONTRACTOR SHALL COORDINATE WITH BUILDING OWNER PRIOR TO START OF WORK,
<br />3• THE REQUIREMENTS FOR CORING OF FLOOR SLAB FOR ALL REQUIRED WORK.
<br />4• THE ARCHITECT AND ENGINEERS, AND CONSULTANTS SHALL HAVE NO RESPONSIBILITY
<br />5_ FOR THE DISCOVERY, PRESENCE, HANDLING, REMOVAL OR DISPOSAL OF OR EXPOSURE OF
<br />PERSONS TO HAZARDOUS MATERIALS IN ANY FORM AT THE PROJECT SITE, INCLUDING BUT
<br />NOT LIMITED TO ASBESTOS PRODUCTS, POLYCHLORINATED BIPHENYL (PCB) OR OTHER
<br />6• TOXIC SUBSTANCES.
<br />COMPLY WITH APPLICABLE CODES AND/OR ORDIANCES CONCERNING DEMOLITION
<br />OPERATIONS, REFUSE REMOVAL, AND DISPOSAL.
<br />DIVISION 3 CONCRETE
<br />8. CLEAN, GRIND AND FILL EXISTING CONCRETE TO ACCEPT VINYL TILE, CARPER, OR CERAMIC
<br />TILE.
<br />FLOORS TO RECEIVE TILE OR SHEET VINYL SHALL NOT VARY MORE THAN 1 /4" PER 10 FT.
<br />IflIVISION 5 METALS
<br />2 STEEL FRAMING: WITH EACH TYPE OF METAL FRAMING REQUIRED, PROVIDE
<br />MANUFACTURER'S STANDARD STEEL RUNNER, BLOCKING, LINTELS, CLIP ANGLES, SHOES,
<br />REINFORCEMENTS, FASTENERS AND ACCESSORIES AS RECOMMENDED BY THE
<br />MANUFACTURER FOR THE APPLICATIONS INDICATED.
<br />1 METAL STUDS: OPEN BOX SHAPED SECTIONS, 3-1/2 INCH x 25 GAGE MIN. (20 GAGE FOR
<br />STUDS OVER 14'-0" IN HT. AND AT WALL AT WATER HEATER / MOP SINK ENCLOSURE).
<br />DIVISION 7 THERMAL & MOISTURE PROTECTION
<br />2. ALL INSULATING MATERIALS IN CONCEALED SPACES HAVE A FLAME SPREAD RATING OF
<br />75 OR LESS AN A SMOKE DEVELOPED RATING OF 450 OR LESS PER ASTM E84.
<br />DIVISION 8 DOORS & WINDOWS
<br />1. ALL GLASS SUBJECT TO HUMAN IMPACT SHALL CONFORM TO THE STANDARD SET FORTH
<br />IN THE LOCAL BUILDING CODE.
<br />ALL EXITS SHALL BE OPERABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR
<br />1. SPECIAL KNOWLEDGE.
<br />MANUALLY OPERATED EDGE OR SURFACE -MOUNTED FLUSH BOLTS AND SURFACE BOLTS
<br />2. OR ANY OTHER TYPE OF DEVICE THAT MAT BE USED TO CLOSE OR RESTRAIN THE DOOR
<br />ARE PROHIBITED. WHERE EXIT DOORS ARE USED IN PAIRS AND APPROVED AUTOMATIC
<br />FLUSH BOLTS ARE USED, THE DOOR LEAF HAVING THE AUTOMATIC FLUSH BOLTS SHALL
<br />3-HAVE NO DOORKNOB OR SURFACE -MOUNTED HARDWARE. THE UNLATCHING OF ANY LEAF
<br />SHALL NOT REQUIRE MORE THAN ONE OPERATION.
<br />PANIC HARDWARE, WHERE INSTALLED, SHALL COMPLY WITH THE LOCAL BUILDING CODE.
<br />THE ACTIVATING MEMBER SHALL BE MOUNTED AT 36 TO 44 INCHES ABOVE THE FINISH
<br />FLOOR. THE UNLATCHING FORCE SHALL NOT EXCEED 15 POUNDS WHEN APPLIED IN THE
<br />DIRECTION OF TRAVEL.
<br />4DIVISION 9 FINISHES
<br />1.INTERIOR FINISHES TO HAVE A MAXIMUM FLAME SPREAD RATING OF 200 AND MAXIMUM
<br />SMOKE DEVELOPMENT RATING OF 450.
<br />2. STUD PARTITIONS TO BE ANCHORED SO AS TO RESIST A LATERAL LOAD OF 5 PSF AS
<br />FOLLOWS, BOTTOM PLATE: ANCHOR TO SUB FLOOR WITH 300# POWER DRIVEN PINS AT
<br />48" O.C. ICBO #1639
<br />3. GYP BOARD WALLS TO BE TAPED, SANDED AND HAVE SMOOTH FINISH, UNLESS NOTED
<br />OTHERWISE.
<br />4. THE CONTRACTOR SHALL PROVIDE AND INSTALL CAULKING WHERE NOT SPECIFICALLY
<br />PERFORMED BY OTHER TRADES.
<br />5. CERAMIC TILE FLOORS SHALL NOT VARY MORE THAN 1 /4" PER 10 FEET.
<br />DIVISION 10 SPECIALTIES
<br />1. SUITE NUMBER OR ADDRESS TO BE POSTED ABOVE DOOR.
<br />2. CONTRACTOR SHALL BE RESPONSIBLE FOR THE DESIGN AND INSTALLATION /
<br />MODIFICATION OF THE FIRE SPRINKLER SYSTEM. CONTRACTOR SHALL SUBMIT DRAWING
<br />TO GOVERNING AUTHORITY FOR REVIEW AND APPROVAL PRIOR TO COMMENCING WITH
<br />WORK.
<br />DIVISION 15 MECHANICAL
<br />1. VERIFY EXISTING MECHANICAL EQUIPMENT (HVAC) IS IN FULL WORKING ORDER, REPLACE
<br />FILTERS THROUGHOUT SYSTEM.
<br />2. VERIFY FRESH AIR SETTING, HUMIDITY CONTROLS, BALANCE, ETC. ARE ADEQUATE FOR
<br />PROPOSED USE. REPLACE AND/OR MODIFY SYSTEM AS REQUIRED FOR COMPLIANCE WITH
<br />LOCAL GOVERNMENTAL AGENCIES REQUIREMENTS.
<br />SAMUEL OLMEDO
<br />ARCHITECT
<br />FL. REG. AR0015027
<br />TEL. 407. 967. 3109
<br />soarcht @ yahoo.com
<br />P.O. BOX 784825
<br />WINTER GARDEN, FL. 34778
<br />W
<br />_1
<br />LL
<br />\ o
<br />0
<br />W
<br />PERMIT SET
<br />REVISIONS:
<br />NO DATE DESCRIPTION
<br />3-25-12 JII CORP
<br />INSTRUMENTS OF SERVICE OWNERSHIP
<br />ALL REPORTS, PLANS, SPECIFICATIONS,
<br />COMPUTER FILES, FIELD DATA, NOTES
<br />INSTRUMENTS PREPARED BY THE
<br />AND OTHER DOCUMENTS AND RELATED
<br />INSTRUMENTS PREPARED BY THE
<br />ARCHITECT OR CONSULTANTS AS
<br />INTRUMENTS OF SERVICE SHALL REMAIN
<br />THE PROPERTY OF THE ARCHITECT OR
<br />CONSULTANT. THE ARCHITECT AND OR
<br />THE CONSULTANT SHALL RETAIN ALL
<br />COMMON LAW, STATUTORY AND OTHER
<br />RESERVED RIGHTS, INCLUDING THE
<br />COPYRIGHT THERETO.
<br />RESTAURANT
<br />INTERIOR BUILD -OUT
<br />FOR:
<br />JEREMIAH'S
<br />TALIAN ICE
<br />7936 GALL BLVD
<br />ZEPHYRHILLS, FL 33541
<br />SHEET
<br />EXISTING FLOOR PLAN AND
<br />EXISTING REFLECTIVE
<br />CEILING PLAN
<br />AOO 00
<br />J
<br />W
<br />D
<br />Q
<br />
|