6194 Back Forty Lp - Laserfiche WebLink

Browse Search

TAPE EDGE OF HEAD WALL FLASHING STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP)— WALL SHEATHING PER PLAN — SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED----- WEEP SCREED— -_ CONT SELF ADHERED FLASHING TURN 3" UP WALL- 18 GA HEAD WALL FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT SHINGLE ROOF PER SPECS — ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN NOTE: ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL 3"=1'-0" TAPE EDGE OF HEAD WALL FLASHING STUCCO ON FRAME - 7!8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED ---- WEEP SCREED HEAD WALL TRIM FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT CONT SELF ADHERED FLASHING TURN 3" UP WALL— CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS 'Z' CLOSURE STANDING SEAM METAL ROOF PER SPECS ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN 3"= 1'-0" R z 00 HEAD WALL R 211_10I11111111111M STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED TAPE EDGE OF COUNTER FLASHING WEEP SCREED COUNTER FLAS73"UP CONT SELF AD FLASHING TURN WALL SHINGLE PER SPECS STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN NOTE: ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP; TAPE EDGE OF RAKE WALL FLASHING WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED LVITAIAMIGIN :I. RAKE WALL STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT FIELD BEND PANEL UP 1 1/2" CONT BUTYL TAPE SEALANT 7PER MANUFACTURER INSTALLATION INSTRUCTIONS 'Z' CLOSURE \ STANDING SEAM METAL ROOF PER SPECS ROOF UNDERLAYMENT TO \ TURN UP WALL MIN J-- ROOF SHEATHING NOTE: PER PLAN ALL LATH AND LATH ATTACHMENTS TO BE CONT SELF ADHERED OUT OF CORROSION FLASHING TURN 3" UP WALL -RESISTANT MATERIAL HEAD WALL I2 in u TAPE EDGE OF HEAD WALL FLASHING FIBER CEMENT SIDING PER ELEVATIONS AV WALL SHEATHING PER PLAN - SHINGLE WATER RESISTIVE BARRIER OVER FLASHING STARTER STRIP-----_ 00 CONT SELF ADHERED FLASHING TURN 3" UP WALL- 18 GA HEAD WALL FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT SHINGLE ROOF PER SPECS - ROOF UNDERLAYMENT TO z TURN UP WALL MIN 8" — 2 - ROOF SHEATHING 00 PER PLAN RAKE WALL WP12 - ROOF 3 -1 -0 , TAPE EDGE OF HEAD _ WALL FLASHING R RAKE WALL WP14 FIBER CEMENT SIDING PER ELEVATIONS WALL SHEATHING PER P SHINGLE WATER RESISTIVE BARRIER OVER FLASHING MIN STARTER STRI HEAD WALL TRIM FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT CONT SELF ADHERED FLASHING TURN 3" UP WALLS CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS 'Z' CLOSURE STANDING SEAM METAL ROOF PER SPECS ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN 311=1'-01' FLASHING REQUIREMENTS (D R730.1 GENERAL. EXTERIOR WALLS SHALL PROVIDE THE BUILDING WITH A O WEATHER -RESISTANT EXTERIOR WALL ENVELOPE. THE EXTERIOR WALL ENVELOPE Cn SHALL INCLUDE FLASHING AS DESCRIBED IN SECTION R703.4. U O O -*- R703A .1 WATER RESISTANCE. THE EXTERIOR WALL ENVELOPE SHALL BE DIMENSIONED L- FIBER CEMENT SIDING AND CONSTRUCTED IN A MANNER THAT PREVENTS THE ACCUMULATION OF WATER (D 0-O PER ELEVATIONS WITHIN THE WALL ASSEMBLY BY PROVIDING A WATER-RESISTANT BARRIER BEHIND THE co - WALL SHEATHING PER PLAN EXTERIOR CLADDING AS REQUIRED BY SECTION R703.2 AND A MEANS OF DRAINING TO � U U THE EXTERIOR WATER THAT PENETRATES THE EXTERIOR CLADDING. =3 cz Cu U) SHINGLE WATER N -0 U 00 RESISTIVE BARRIER R703.2 WATER RESISTIVE BARRIER. ONE LAYER OF NO.15 ASPHALT FELT, FREE FROM C LO O OVER FLASHING HOLES, COMPLY WITH ASTM D226 FOR TYPE 1 FELT OR OTHER APPROVED O 0 C O WATER -RESISTIVE BARRIER SHALL BE APPLIED OVER STUDS OR SHEATHING OF ALL C C O V- TAPE EDGE OF COUNTER EXTERIOR WALLS NO. 15 ASPHALT FELT SHALL BE APPLIED HORIZONTALLY, WITH THE co O `*CU - FLASHING UPPER LAYER LAPPED OVER THE LOWER LAYER NOT LESS THAN 2 INCHES. WHERE .� -0 E O O 00 JOINTS OCCUR, FELT SHALL BE LAPPED NOT LESS THAN 6 INCHES. OTHER APPROVED U) O L C)- STARTER STRIP MATERIALS SHALL BE INSTALLED IN ACCORDANCE WITH THE WATER -RESISTIVE cuu) 4O Q COUNTER FLASHING BARRIER MANUFACTURER'S INSTALLATION INSTRUCTIONS. THE NO.15 ASPHALT FELT I— —0 U) Q OR OTHER APPROVED WATER -RESISTIVE BARRIER MATERIAL SHALL BE CONTINUOUS CONT SELF ADHERED TO THE TOP OF WALLS AND TERMINATED AT PENETRATIONS AND BUILDING FLASHING TURN 3" UP WALL APPENDAGES IN A MANNER TO MEET THE REQUIREMENTS OF THE EXTERIOR WALL ENVELOPE AS DESCRIBED IN SECTION R703.1. z SHINGLE PER SPECS R703.7.3 WATER -RESISTIVE BARRIERS WATER -RESISTIVE BARRIERS SHALL BE 0o STEP FLASHING TO INSTALLED AS REQUIRED IN SECTION R703.2 AND, WHERE APPLIED OVER WOOD -BASED d EXTEND MIN 8" BEYOND SHEATHING, SHALL INCLUDE A WATER -RESISTIVE VAPOR -PERMEABLE BARRIER WITH A UNDERLAYMENT PERFORMANCE AT LEAST EQUIVALENT TO TWO LAYERS OF GRADE D PAPER. THE z INDIVIDUAL LAYERS SHALL BE INSTALLED INDEPENDENTLY SUCH THAT EACH LAYER ROOF UNDERLAYMENT TO PROVIDES A SEPARATE CONTINUOUS PLANE AND ANY FLASHING (INSTALLED IN TURN UP WALL MIN 8" 14 00 ACCORDANCE WITH SECTION R703.4) INTENDED TO DRAIN TO THE WATER -RESISTIVE BARRIER IS DIRECTED BETWEEN THE LAYERS. ROOF SHEATHING PER PLAN CO EXCEPTION: WHERE THE WATER -RESISTIVE BARRIER THAT IS APPLIED OVER 6„ WOOD -BASED SHEATHING HAS A WATER RESISTANCE EQUAL TO OR GREATER THAN THAT OF 60-MINUTE GRADE D PAPER AND IS SEPARATED FROM THE STUCCO BY AN INTERVENING SUBSTANTIALLY NON -WATER -ABSORBING LAYER OR 6" DESIGNED DRAINAGE SPACE. R703.4 FLASHING. APPROVED METAL FLASHING, VINYL FLASHING, SELF -ADHERED MEMBRANES AND MECHANICALLY ATTACHED FLEXIBLE FLASHING SHALL BE APPLIED SHINGLE -FASHION OR IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. METAL FLASHING SHALL BE CORROSION RESISTANT. FLUID -APPLIED MEMBRANES USED AS FLASHING SHALL BE APPLIED IN ACCORDANCE WITH THE MANUFACTURER'S HEAD WALL RAKE WALL INSTRUCTIONS. ALL FLASHING SHALL BE APPLIED IN A MANNER TO PREVENT THE - SHINGLE TO SIDING ENTRY OF WATER INTO THE WALL CAVITY OR PENETRATION OF WATER TO THE W P 13 BUILDING STRUCTURAL FRAMING SELF -ADHERED MEMBRANES USEDASFLASHING SHALL COMPLY WITH MMA 711. ALL EXTERIOR FENESTRATION PRODUCTS SHALL BE SEALED AT THE JUNCTURE WITH THE BUILDING WALL WITH A SEALANT COMPLYING WITH AAMA 800 OR ASTM C920 CLASS 25 GRADE NS OR GREATER FOR PROPER JOINT EXPANSION AND CONTRACTION, ASTMC1281, MMA 812, OR OTHER APPROVED STANDARD AS APPROPRIATE FOR THE TYPE OF SEALANT. FLUID -APPLIED MEMBRANES USED AS FLASHING IN EXTERIOR FIBER CEMENT SIDING WALLS SHALL COMPLY WITH AAMA 714. THE FLASHING SHALL EXTEND TO THE SURFACE PER ELEVATIONS OF THE EXTERIOR WALL FINISH. APPROVED FLASHINGS SHALL BE INSTALLED AT THE FOLLOWING LOCATIONS: TAPE EDGE OF RAKE WALL FLASHING 1. 1. EXTERIOR WINDOW AND DOOR OPENINGS. FLASHING AT EXTERIOR WINDOW WALL SHEATHING PER PLAN AND DOOR OPENINGS SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER -RESISTIVE BARRIER COMPLYING WITH SECTION 703.2 SHINGLE WATER FOR SUBSEQUENT DRAINAGE. MECHANICALLY ATTACHED FLEXIBLE FLASHINGS RESISTIVE BARRIER SHALL COMPLY WITH MMA 712. FLASHING AT EXTERIOR WINDOW AND DOOR OVER FLASHING MIN 8" OPENINGS SHALL BE INSTALLED IN ACCORDANCE WITH ONE OR MORE OF THE FOLLOWING: 00 STARTER STRIP 00 1.1 THE FENESTRATION MANUFACTURER'S INSTALLATION AND FLASHING RAKE WALL STEP FLASHING TO INSTRUCTIONS, OR FOR APPLICATIONS NOT ADDRESSED IN THE EXTEND MIN 8" BEYOND FENESTRATION MANUFACTURER'S INSTRUCTIONS, IN ACCORDANCE WITH UNDERLAYMENT THE FLASHING MANUFACTURER'S INSTRUCTIONS. WHERE FLASHING INSTRUCTIONS OR DETAILS ARE NOT PROVIDED, PLAN FLASHING SHALL BE FIELD BEND PANEL UP 1 1/2" INSTALLED AT THE SILL OF EXTERIOR WINDOW AND DOOR OPENINGS. PAN FLASHING SHALL BE SEALED OR SLOPED IN SUCH A MANNER AS TO DIRECT CONT BUTYL TAPE SEALANT PER WATER TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER MANUFACTURER INSTALLATION RESISTIVE BARRIER FOR SUBSEQUENT DRAINAGE. OPENINGS USING PAN INSTRUCTIONS FLASHING SHALL INCORPORATE FLASHING OR PROTECTION AT THE HEAD AND SIDES. 00 Z' CLOSURE 1.2 IN ACCORDANCE WITH THE FLASHING DESIGN OR METHOD OF A STANDING SEAM METAL o0 REGISTERED DESIGN PROFESSIONAL. ROOF PER SPECS 1.3 IN ACCORDANCE WITH THE OTHER APPROVED METHODS. 1.4 IN ACCORDANCE WITH FMA/AAMA 100, FMA/AAMA 200, FMA/WDMA ROOF UNDERLAYMENT TO 250, FMA/AAMA/WDMA 300 OR FMA/AAMA/WDMA 400. TURN UP WALL MIN 8" 2.2 AT THE INTERSECTION OF CHIMNEYS OR OTHER MASONRY CONSTRUCTION WITH FRAME OR STUCCO WALLS, WITH PROJECTING LIPS ON BOTH SIDES UNDER STUCCO COPINGS. 3.3 UNDER AND AT THE ENDS OF MASONRY, WOOD OR METAL ROOF SHEATHING COPINGS AND SILLS. PER PLAN__,, LAN 4.4 CONTINUOUSLY ABOVE ALL PROJECTING WOOD TRIM. 5.5 WHERE EXTERIOR PORCHES, DECKS OR STAIRS ATTACH TO A CONT SELF ADHERED WALL OR FLOOR ASSEMBLY OF WOOD -FRAME CONSTRUCTION. FLASHING TURN 3" UP WALL 6.6 AT WALL AND ROOF INTERSECTIONS. HEAD WALL RAKE WALL 7.7 AT BUILT-IN GUTTERS. f - STANDING SEAM ROOF TO SIDING THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL WP 15 FLASHING AND WATERPROOFING METHODS TO BE USED. Cif.. aD a� 0 � to MAY 0 Z 2023 O Virtual Review Assist, Inc. r 0 Plans Review completed and approved U Ofor compliance with the 2020 F6C 7th Edition by Debra Anne Klahr PX2300 L- cn co Q z z J d SHEET NO. WP 2,0