7821 Gall Blvd (2) - Laserfiche WebLink

Browse Search

54 min 36 min 1370 11.4.16 WATER CLOSETS. 12 min 915 12 min 12 max 42 min 30� 305 306 1045 to8et 11-4.16.1 General. Accessible water closets shall comply with paper 11-4.16. 11-4.16.2 Clear Floor Space, Clear floor space for water m closets not in stalls shall comply with Fig. 28. Clear floor 7 space may be arranged to allow either a left-handed or right- (a) (b) handed approach. Back Wall Side wall Fig. 29 11-4.16.3 Height. The height of water closets shall be 1 T' to Crab bars at Water Closets 19" (430 mm to 485 mm), measured to the top of the toilet seat (see Fig. 29(b)). Seats shall not be sprung to return to a lifted position. 114.16.4 Grab Bars. Grab bars for water closets not located in stalls shall comply with 11.4.26 and Fig. 29. The grab bar behind the water closet shall be 36" (915mm) minimum. 11-4.16.5 Flush Controls. Flush controls shall be hand operated or automatic and shall comply with 11-4.27.4. Controls for flush valves shall be mounted on the wide side of toilet areas no more than 44" (1120mm) above the floor. 11-4.16.6 Dispensers. Toilet paper dispensers shall be installed within reach, as shown in Fig. 29(b). Dispensers that control delivery, or that do not permit continuous paper flow, shall not be used. 42 min 18 min 1045 456 dear floor space 4 60 min 1525 Fig. 28 Clear Floor Space at Water Closets WATER CLOSETS IX TOILET STALLS(per FLORIDA ACCESSIBILITY CODE for BUILDING CONSTRUCTION) SCALE: N.T.S. 17.19 430 485 LUb 7ou equipment permitted in shaded area a Spout eight and Knee Clearance 8 min. 1220 I � I ��24 max 610 (b) Clear Floor Space not to exceed ° fountain depthL-7 ° C ---J 48 min 48 min 1220 1220 (c) (d) Freestanding Built-in Fountain or Cooler Fig. 27 Fountain or Cooler Drinking Fountains and Water Coolers 4.15 DRINKING FOUNTAINS AND WATER COOLERS. 4.15.1. Minimum Number. Drinking fountains or water coo ers required to be accessible by 4.1 shall comply with 4.15. 4.15 2* S out Hei ht. Spouts shall be no higher than 36" mm , measure rom the floor or ground surfaces to be e spout outlet (see Fig. 27(a)). 4.15.3 Spout Location. The spouts of drinking fountains an water coolers shall be at the front of the unit and shall direct the water flow in a trajectory that is parallel or nearly of water at least 4"(100mm) higgh so as to allow the insertion arallel to t front of t ie nit. Tjte stpou8shall rovide flow o a cup or g ass under a ow oT wa er. n an ccessible drinking fountain with a round or oval bowl the spout must be positioned so the flow of water is within M5mm) of the front edge of the fountain. 4.15.4 Controls. Controls shall comply with 4.27.4. Unit controls is shall b front mounted or side mounted near the front edge. 4.15.5 Clearances. (1) Wall and post -mounted cantilevered units shall have a clear knee space between the bottom of the a,pron and the floor or ground at least 21"(685pmmll high, 30"(760mm) wide, and 17" to 19"lar 30mm to 485mm) deep (see Fig. 27(a) and). Such units shall also have a minimum floor space 30" by 48" (760 mm byy 1220mm) to allow a person in a wheetchair to approach the unit facing forward. (2) Freestanding or built-in units not having a clear space under them shall have a clear floor space at least 30" by 48" (760 mm by 1220 mm) that allows a person in a wheelchair to make a parallel approach to the unit (see Fig. 27(c) and M. This dear floor space shall comply with �.2.4. DRINKING FOUNTAINS SCALE: N.T.S. 4.13 DOORS. 4.13.1 General. Doors required to be accessible by 4.1 shall comply requirements of 4.13. 4.13.2 Revolving Doors and Turnstiles. Revolving doors or Tumstiles steal not be e only of passage at an accessible entrance or along an accessible route. An accessible gate or door shall be provided adjacent to the tumstile or revolving door and shall be so designed as to facilitate the same use pattern. 4.13.3 Gates. Gates, including ticket gates, shall meet all app I—fcable specifications of 4.13. 4.13.4 Doubledeaf Doorways. If doorways have two en en y opera a ooreaves, then at least one leaf indepi shall meet the specifications n 4.13.5 and 4.13.6. That leaf 32 min 815 shall be an active leaf. 4.13.5 Clear Width. Doorways shall have a minimum dear operimg o mm) with the door open 90°, measured Mace between the the door and the opposite stopp (see Fig. 24(a),(b),(c) and (d)). Openings more than 24"(610mm in (a) deptthh shall) comply with 4.2.1 and 4.3.3 (see fig. 24(e)�. Dot* EXCEPTION: Doors not requiring full user passage, such as shallow closets, may have the dear opening reduced to 20" (510mm) minimum. 4.13.6 Maneuvering Clearances at Doors. Minimum maneuvering clearances a doors that are not automatic or shall be shown in Fig. 25. The floor or 32 min 815 power -assisted ground area within the required clearances shall be level and clear. EXCEPTION. Entry doors to acute care hospital bedrooms for t�) in -patients shall be exempted from the requirement for space Sliding Door at the latch side of the door (see dimension "x" in Fig. 25) if the door is at least 44" (1120mm) wide. 4.13.7 Two Doors in Series. The minimum space between 32 min o Inge or plvo a oors in series shall be 48"(1220mm) 815 plus the width of any door swinging into the space. Doors in series shall swing either in the same direction or away from the-®o space between the doors (see Fig. 26). (d) 4.13.8* Thresholds at Doorwa s. Thresholds at Folding Door oorways shall no excee 9mm) in height for exterior sliding ddoors or 112"((13mm for other types of doors. Raised thresholds and floorlevel c�anges at accessible doorwayys shall be beveled with a slope no greater than 1:2 (see 4.5.2). 4.13.9* Door Hardware. Handles, pulls, latches, locks and other opera ing devices on accessible doors shall have a shape that is easy to grasp with one hand and does not require tight grasping, tight pinching, or twisting of the wrist to operate. Lever -operated mechanisms, and U-shaped handles are acceptable designs. When sliding doors are fully opened, 4.19 LAVATORIES AND MIRRORS, 4.19.1 General. The requirements of 4.19 shall apply to lavatory fixtures, vanities, and built-in lavatories. 4.19.2 Height and Clearances. Lavatories shall be mounted with the rim or counter surface no higher than 34" (865 mm) above the finish floor. Provide a clearance of at least 29" (735 mm) above the finish floor to the bottom of the apron. Knee and toe clearance shall comply with Fig. 31, 4.19.3 Clear Floor Space. A dear floor space 30" by 48" (760 mm by 1220 mm) complying with 4.2.4 shall be provided in front of a lavatory to allow forward approach. Such dear floor space shall adjoin or overlap an accessible route and shall extend a maximum of 19" (485 mm) underneath the lavatory (see Fig. 32). 4.19.4. Exposed Pipes and Surfaces. Hot water and drain pipes under lavatories shall be insulated or otherwise configured to protect against contact. There shall be sharp or abrasive surfaces under lavatories. 4.19.5 Faucets. faucets shall comply with 4.27.4 Lever - operated, push -type, and electronically controlled mechanisms are examples of acceptable designs. If self -dosing valves are used the faucet shall remain open for at least 10 seconds. 4.19.6* Mirrors. Mirrors shall be mounted with the bottom edge of the reflecting surface no higher than 40" (115 mm) above the finish floor (see Fig. 31). Fig. 24 Clear Doorway Width and Depth operating hardware shall be expose and usable from both sides. Hardware required for accessible door passage shall be mounted no higher than 48"(1220mm) above finished 48 min floor. .- LAVATORIES SCALE: N.T.S. 32 MIN 815 (b) Hinged Door 31 min 815 Max mum Doorway Depth 4.13.10* Door Closers. If a door has a closer, then the sweep period of the closer shall be adjusted so that from an I open position of 70°, the door will take at least 3 seconds to _ move to a point 3"(75mm) from the latch, measured to the \ \ leading edge of the door. — 4.13.11* Door Opening Force. The maximum force for pushing or pulling open a door shall be as follows: (1) Fire doors shall have the minimum opening force allowable by the appropriate administrative authority. (2) Other doors: (a) exterior hinged doors: (Reserved). b interior hinged doors: bf�22.2N). c slidingg�or folding doors: 5 bf (22.2N). These forces do not apply to the force required to retract latch bolts or disengage other devices that may hold the door in a closed position. 46 min 4.13.12* Automatic Doors and Power -Assisted Doors. If 1220 an automatic door is used, then it shall comp with ANSIIBHMA A155.10-1985. Slow) oppening, ow owered, automatic doors shall comply withyANSI A 956.19-1984. Such doors shall not open to back check faster than 3 seconds and — shall require no more than 15 Ibf(66.6N) to stop door movement. If a power -assisted door is used, its door -opening forceshall comply with 4.13.11 and its dosing shall conform to requirements in ANSI A 156.19-1984. L 4.14 ENTRANCES. 4.14.1 Minimum Number. Entrances required to be accessible by 4.1 shall e part of an accessible route complying with 4.3. Such entrances shall be connected byy an accessible route to public transportation stopps, to accessble parkin and passenger loading zones, and to ublic streets or sidewalks if available (see 4.3.2(1)). They shah also be Fig. 26 connected by an accessible route to all accessible spaces or Two Hinged Doors in Series elements within the building or facility. DOORS & MANEUVERING CLEARANCES SCALE: N.T.S. 430 Fig. 31 Lavatory Clearances 17 min a3o dear floor O space o 19 max 485 48 min 1220 Fig. 32 Clear Floor Space at Lavatories F_T --- E I I I I I 18 min. 24 preferred 455 II� NOTE: x =12 in (305 mm) if door has both a closer and latch. (a) Front Approaches -Swinging Doors NOTE: x= 36 in (915 mm) minimum if y=60 in (1525 mm): x=42 in (1063 mm) minimum'rfy = 54 in (1370 mm) 54 min — 1370 1 NOTE: y = 48 in (1220 mm) m nimum if door h s both a latch and closer. Hinge Side Approaches -Swinging Doors 24 min 610 24 min X 610 ,1 F_----� IF I NOTE: y = 54 in (1370 mm) minimum if door has NOTE: y = 48 in (1220 mm) minimum door has closer. closer. Latch We Approaches- Swinging Doors Robert E. Gregg FL #9927 KY #3396 CT #8163 SC #4334 NJ#15414 MS #2335 VA #5737 OH #5898 TN i4334 Copy of this plan is not valid unless signed, sealed and dated by the architect of record Copywrite: This drawing is the property of R.E. Gregg Architects and under no circumstances may this drawing be reproduced, published, altered or used in any way without written authorization from R.E. Gregg Architects. Contractor shall check and verify all dimensions and coordinate all field conditions. All discrepancies and conflicts shall be reported to the architect in writing prior to proceeding or continuing with construction. Unreported discrepances and conflicts shall remain the responsibility of the contractor. o LL W UJI C/3 U3 Qf ti J z Q = UJ N QO I-- 54 min 1370 DRAWN BY: KG I CHECKED BY: REG (d) (a) FrontApproach- SlidingDoors Slide Side Approach --SlidingDoors ISSUE DATE: 1-12-2022 and folding Doors and Folding Doors x 24 min 610 NOTE: All doors in alcoves F shall comply with the dearances for front approaches (fl Latch Side Approach - Sliding Doors and Folding Doors Fig. 25 Maneuvering Clearances at Doors (Continued) ADA SPECIFICATIONS G002