|
rmrn/-�I n [ Cl f•ulnlnl r In ICITn I I rn n CI nCn
<br />EXTERIOF
<br />PLASTER
<br />FRAME
<br />FIBERGLASS SHINGLE INSTALLED AS PER
<br />MANUFACTURER SPECIFICATIONS
<br />TOM
<br />-
<br />IGT_— — — I --
<br />FLR__--I--
<br />12 4'
<br />12
<br />5
<br />(2) 25 SH
<br />CJ / WEEP
<br />35 SH
<br />REAR ELEVATION - A
<br />SCALE: 1/4" = 1'-0"
<br />EXTERIOR PLASTER
<br />ON FRAME
<br />TEXTURED
<br />CEMENTITIOUS
<br />FINISH ON CMU
<br />T.O.M.
<br />T.O.M. @
<br />ZJ ENTRY
<br />DR. HGT.
<br />TEXTURE[
<br />CEMENTITI
<br />FINISH ON
<br />FLR.
<br />LEFT ELEVATION - A
<br />SCALE: 1/4" = 1'-0"
<br />I
<br />General Notes
<br />ROOF CRITERIA:
<br />• 12" OVERHANG U.N.O.
<br />• PLUMB CUT FASCIA ROOF
<br />• PITCH PER ELEVATION
<br />**G.C. VERIFY ROOF PITCH**
<br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE
<br />CONTRACTORS RESPONSIBILITY TO VERIFY
<br />ROOF SLOPE REQUIREMENTS WITH TRUSS
<br />MANUFACTURER.
<br />**ELECTRICAL SPECIFICATION NOTES**
<br />ELECTRICAL CONTRACTOR MUST VERIFY WITH
<br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE
<br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR
<br />LOCATION PURPOSES.
<br />I Exterior Covering
<br />R703.7 Exterior Plaster.
<br />Installation of these materials shall be in compliance with ASTM
<br />C926 and ASTM C1063, or ASTM C1787 and the provisions of
<br />this code.
<br />R703.7.1 Lath.
<br />Lath and Lath attachments shall be of corrosion -resistant
<br />materials. Expanded metal or woven wire lath shall be attached
<br />with 1-1/2" long, 11 gage nails having a 7/16" head, or 1-1/2" long,
<br />16 gage staples, spaced in accordance with ASTM C1063 or
<br />C1787, or as otherwise approved. (Refer to sheet SN1 for the
<br />engineered method for Lath attachment.)
<br />Lathing Accessories
<br />Attachments shall be of corrosion -resistant materials.
<br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @
<br />6" O.C. vertically/horizontally into the framing members.
<br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia.
<br />min. @ 6" O.C. vertically/horizontally or compatible adhesives,
<br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C.
<br />or in a semi -continuous bead between the solid plaster base and
<br />the solid portion of the key attachment flange.
<br />Control Joints: Install control joint lathing accessories in
<br />conformance with C1063. Lath shall not be continuous through
<br />control joints, but shall be stopped and tied at each side.
<br />All accessories shall be in accordance with the latest ASTM
<br />C1063 & ASTM C1861.
<br />R703.7.2 Plaster.
<br />Plastering with cement plaster shall be not less than three coats
<br />where applied over any type of code -approved lath and shall be
<br />not less than two coats where directly applied over masonry,
<br />concrete, clay brick, stone, or tile. If the plaster surface is
<br />completely covered by veneer or other facing material or is
<br />completely concealed, plaster application need be only two coats,
<br />provided total thickness is as set in Table R702.1(1).
<br />Cement plaster shall be in accordance with ASTM C926 and
<br />material shall be in accordance with one of the types listed in
<br />R703.7.2.
<br />R703.7.3 Water -Resistive Barriers.
<br />Water -resistive barriers shall be installed as required in Section
<br />R703.2 and, where applied over wood -based sheathing, shall
<br />include a water -resistive vapor -permeable barrier with a
<br />performance at least equivalent to two layers of Grade D paper.
<br />The individual layers shall be installed independently such that
<br />each layer provides a separate continuous plane and any flashing
<br />(installed in accordance with Section R703.4) intended to drain to
<br />the water -resistive barrier is directed between the layers.
<br />R703.2 Water -Resistive Barrier.
<br />One layer of No. 15 asphalt felt, free from holes and breaks,
<br />complying with ASTM D226 for Type 1 felt or other approved
<br />water -resistive barrier shall be applied over studs or sheathing of
<br />all exterior walls. No. 15 asphalt felt shall be applied horizontally,
<br />with the upper layer lapped over the lower layer not less than 2
<br />inches. Where joints occur, felt shall be lapped not less than 6
<br />inches. Other approved materials shall be installed in accordance
<br />with the water -resistive barrier manufacturer's installation
<br />instructions. The No. 15 asphalt felt or other approved
<br />water -resistive barrier material shall be continuous to the top of
<br />walls and terminated at penetrations and building appendages in
<br />a manner to meet the requirements of the exterior wall envelope
<br />as described in Section R703.1.
<br />R703.4 Flashing.
<br />Approved metal flashing, vinyl flashing, self -adhered membranes
<br />and mechanically attached flexible flashing shall be applied
<br />shingle -fashion or in accordance with the manufacturer's
<br />instructions. Metal flashing shall be corrosion resistant.
<br />Fluid -applied membranes used as flashing shall be applied in
<br />accordance with the manufacturer's instructions. All flashing shall
<br />be applied in a manner to prevent the entry of water into the wall
<br />cavity or penetration of water to the building structural framing
<br />components.
<br />Self -adhered membranes used as flashing shall comply with
<br />AAMA 711. All exterior fenestration products shall be sealed at
<br />the juncture with the building wall with a sealant complying with
<br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for
<br />proper joint expansion and contraction, ASTM C1281, AAMA 812,
<br />or other approved standard as appropriate for the type of sealant.
<br />Fluid -applied membranes used as flashing in exterior walls shall
<br />comply with AAMA 714. The flashing shall extend to the surface
<br />of the exterior wall finish.
<br />Approved flashings shall be installed at the following locations.
<br />• Exterior window/door openings.
<br />• Intersection of chimneys or other masonry construction with
<br />frame walls.
<br />• Under and at the ends of masonry, wood or metal copings
<br />and sills.
<br />• Continuously above all projecting wood trim.
<br />• Where exterior porches, decks or stairs attach to a wall or
<br />floor assembly of wood -frame construction.
<br />• At wall and roof intersection.
<br />• At Built-in gutters.
<br />Coastal Flashings
<br />All flashing material for coastal locations (ex: within 3,000 feet of the
<br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless
<br />steel) and shall be selected for compatibility with adjacent wood
<br />preservatives per the manufacturer's recommendations.
<br />REV. 09.24.21
<br />N
<br />®
<br />_: ,
<br />cz
<br />R�
<br />a���
<br />cm. SE
<br />o
<br />pC R7 3 wM-
<br />�
<br />C=
<br />N � T
<br />OC fC2_
<br />9
<br />to +r
<br />R o
<br />J
<br />O
<br />w
<br />�� �,,.. gyp.,. ••. ,e
<br />•' ��, SE 4
<br />_
<br />\O
<br />O �,
<br />FLO
<br />ARoe•.,,..•���'
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifications contained within these
<br />drawings comply with the 2020
<br />Florida Building Code -
<br />Residential 7th Edition. Engineer's signature and seal is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineer's signature and seal.
<br />r H
<br />QM
<br />o 8
<br />N p
<br />Cs r' a
<br />®
<br />U0
<br />N W lc:,:) N OrD
<br />� a)
<br />y
<br />N
<br />onr- rro
<br />3 1
<br />t
<br />a
<br />a)
<br />w
<br />CCU33
<br />3 a
<br />Lu
<br />13Z
<br />L (06O_ Z ii
<br />0
<br />W
<br />�
<br />ro��rn 0
<br />., W
<br />�,�.RLL Z
<br />�^
<br />w
<br />m J
<br />00N oZ Q
<br />N M F
<br />V
<br />O U ¢ 0
<br />Z
<br />W
<br />U (n
<br />El El
<br />z N th
<br />o g
<br />z
<br />a
<br />(An
<br />Q
<br />r
<br />M
<br />z
<br />0170
<br />�
<br />a-1
<br />V,
<br />w
<br />V
<br />O
<br />�
<br />N
<br />", o
<br />ry
<br />wrd
<br />fa
<br />I_ U)
<br />LU
<br />lGSj%PZ
<br />,— J pEIF
<br />me....,
<br />� N
<br />0
<br />Q 0
<br />c
<br />co
<br />w
<br />U
<br />Z
<br />Q
<br />Il
<br />EE
<br />C' E
<br />E U
<br />�o
<br />Wza�
<br />»
<br />z®
<br />oa
<br />H
<br />x0
<br />0O
<br />� U
<br />O E
<br />a F
<br />O Q
<br />w I�
<br />wo
<br />ww
<br />N
<br />C
<br />� C
<br />Qo
<br />a
<br />O U
<br />mo
<br />01
<br />Z
<br />F
<br />Og
<br />Q O
<br />(n
<br />az
<br />WoLL
<br />o
<br />m
<br />3
<br />dz
<br />��
<br />�
<br />JW
<br />=0
<br />I�
<br />V
<br />003
<br />zIa
<br />¢
<br />O
<br />> M
<br />J
<br />O
<br />°'
<br />rn
<br />m
<br />0
<br />T
<br />(.0
<br />y
<br />cc
<br />WU
<br />0
<br />N
<br />m
<br />N
<br />O
<br />0
<br />N
<br />C) \
<br />r
<br />LO
<br />6
<br />m
<br />Cfl
<br />M �
<br />�; LO
<br />o
<br />z
<br />Z
<br />E r
<br />;v
<br />m
<br />`m
<br />a
<br />o
<br />U �
<br />a �?
<br />Q p
<br />C
<br />J
<br />JOB
<br />NO:
<br />23-06116
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />2.2
<br />T- I I_.. II r II III I -I I I T-----F.. I _ _ _. _ __
<br />-.II 61 1'. i:l 1 I FI-i: lilil i� I uiElil 'r-
<br />
|