Laserfiche WebLink
1 <br />, <br />r <br />1 <br />FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />12 <br />4.01 <br />12 <br />FIBEREGLASS SHINLGE INSTALLED 5.01— <br />AS PER MANUFACTURER _ <br />SPECIFICATIONS T- - ,- <br />12 <br />5.01 <br />4' OFF RIDGE VENT <br />--- ----------- <br />PLASTER ON <br />FRAME <br />35-SH <br />R <br />CJ <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />6068 SGD <br />REAR ELEVATION — B <br />SCALE: 1 /4" = V-0" <br />V-0" RIDGE VENT <br />FLASHING <br />12 <br />------------------------------------- - ---------------------------- - �4.0----- <br />NN rLK <br />C <br />------------------------ -------------------------- <br />CJ <br />2'-0" <br />F,1 1 H3-SH <br />---------- ------------------------------------------I---FI <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />LEFT ELEVATION — B <br />SCALE: 1/4" = 1'-0" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />I txterlor uovering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having a 7/16" head, or 1-1/2" long, <br />16 gage staples, spaced in accordance with ASTM C1063 or <br />C1787, or as otherwise approved. (Refer to sheet SN1 for the <br />engineered method for Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />'v <br />� <br />s <br />*' <br />N cc CIE, .� <br />•Q <br />>,r e <br />>a <br />Co d <br />'� to <br />= y to <br />7 c-" <br />c E <br />cco <br />� U <br />>s <br />�! <br />j//*�pi <br />•\�0®���,�1,rb?,O w v <br />•• <br />L� <br />Q <br />, <br />• i� <br />w <br />w <br />U �O <br />Y J'4. <br />�. .� <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineers signature and seal. <br />W <br />I Q <br />of <br />8 <br />y <br />V <br />O N O <br />N CDC O r <br />Y QO a)N N 0] <br />H� <br />Q <br />_ <br />CD <br />C LL LL <br />co J U 11 d <br />w <br />a <br />1 Z <br />r6cm� <br />o <br />.,. W <br />[a N u) Y <br />og�rn 0 <br />W <br />Z <br />IL <br />U _ m w <br />!n N Z c <br />C1 <br />� Z <br />W <br />N <br />O <br />O U U Go <br />t�2 <br />❑ ❑ <br />� N O <br />O O <br />� <br />QQN <br />Z O Q <br />J <br />U) <br />O_ N <br />M <br />z <br />Q) <br />�N <br />U a <br />4-1 t6L <br />w <br />n <br />U <br />O <br />�N <br />W o <br />N <br />U o <br />c ,n s <br />¢ <br />m <br />®®p <br />N <br />�® <br />o <br />Z <br />w <br />m <br />M <br />J <br />p <br />z <br />Z <br />G <br />� <br />LL <br />,E <br />CL p <br />E U00 <br />tU <br />zo <br />0Q� <br />oLL <br />z <br />>M <br />z© <br />oa <br />a <br />o <br />�< <br />c <br />0< <br />wQ <br />wz <br />cn B <br />�o <br />= <br />o�Z <br />m� <br />o , <br />m J <br />m <br />aw <br />� <br />a <br />o� <br />�zo <br />Z <br />g <br />W <br />ci <br />o <br />w< <br />¢o <br />a= <br />�w <br />�= <br />_6 <br />o <br />wY <br />;o <br />V <br />zla� <br />¢ <br />e <br />> Lo <br />rn <br />m <br />0 <br />T <br />Q <br />Y <br />U <br />O <br />N <br />L <br />m <br />= <br />LO <br />N <br />(� <br />> <br />n o <br />LO <br />r <br />Q <br />CD � <br />r <br />CU <br />: <br />iri L0 <br />z <br />Z <br />E T <br />a En <br />-8 <br />cocc <br />d <br />U � <br />Q 0 <br />-1 <br />JOB <br />NO: <br />23-06119 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />2.2 <br />