|
THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED.
<br />3/8" CEMENT
<br />PLASTER
<br />12 MIL DRYLOK
<br />CMU - MASONRY BLOCK
<br />EXTREME
<br />WINDOW
<br />FASTENER
<br />1) SEALANT AT
<br />4) SEALANT JOINT
<br />WINDOW BUCK TO
<br />OUTSIDE EDGE OF
<br />'' MASONRY
<br />WINDOW BUCK
<br />e
<br />SEALANT JOINT
<br />5) SEALANT FROM
<br />ti •, INSIDE EDGE O2)
<br />F
<br />WINDOW FRAME
<br />WINDOW BUCK
<br />ACROSS WINDOW BUCK
<br />AND EXTEND TO
<br />WINDOW FRAME
<br />MASONRY
<br />ATTACHED
<br />PER CODE
<br />6) TOOLED SEALANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW
<br />FRAME
<br />3) SEALANT WINDOW FRAME TO
<br />WINDOW BUCK ALL THE WAY
<br />AROUND, INCLUDING SILL.
<br />SCS 06_05 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />JAMB, SILL AND HEAD DETAIL
<br />APPROVED SHEATHING
<br />APPROVED HOUSEWRAP
<br />STRUCTALATH TWIN TRACK 2.5
<br />3/4" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />"'SEALANT SOCKET WITH
<br />TOOLED APPROVED SEALANT
<br />SCS 06_02 WINDOW FIN INTERFACE WITH
<br />EXTRUDED SHOULDER
<br />WEATHER
<br />`RESISITIVE
<br />BARRIER
<br />HEAD FLASHING TIE-IN INSTRUXTIC
<br />1. Cut, fold up & temporarily secure
<br />resistive barrier above header to allow for
<br />flashing installation
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold weather resistive barrier back over head
<br />flashing and seal with tape
<br />S
<br />DO NOl
<br />BOTTO!
<br />FLANGL
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND
<br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC
<br />R703.2.1 AND FBCR 703.7.3
<br />Detail Instructions
<br />Refer to the number marked as ## in each detail that corresponds to the
<br />numbered items in the list of Instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8. Mechanically fasten as necessary
<br />SELF -ADHERED FLASHING
<br />DECK JOIST
<br />2x FRAMEWALL
<br />TILE FINISH-
<br />1/2" DUROCK-
<br />8" CMU
<br />WEATHER
<br />✓E BARRIER &
<br />tARILY SECURE
<br />WOOD FRAME CONSTR.
<br />EXTERIOR SELF -ADHERED FLASHIN
<br />SHEATHING BY LAPPING DOWN
<br />OVER RIM JOIST AND UP
<br />WALL BY 6 IN.
<br />WEATHER
<br />RESISITIVE
<br />BARRIER SEAL TOPS OF JOI;
<br />UNDER DECKING
<br />ED FLASHING (SEE DETAIL WP07)
<br />0
<br />o�
<br />ASHING
<br />WEATHER RESISTIVE
<br />BARRIER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />EXTERIOR SHEATHING
<br />314"-1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND RETURN
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />SECTION -A (SEE DETAIL WP02)
<br />SELF -ADHERED FLASHING v
<br />1 0
<br />2 SEAL TOPS OF JOISTS
<br />8 UNDER DECKING
<br />(SEE DETAIL WP07)
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />M
<br />2
<br />V-4" PER PLAN
<br />V-0" PER PLAN
<br />4" OR 8" CMU
<br />(PER SEAT DEPTH)
<br />°
<br />FILL WITH GROUTQ�
<br />HA
<br />-
<br />SLOPED MUD BED
<br />\,a
<br />d
<br />°
<br />°
<br />d
<br />VINYL SHOWER PAN
<br />d
<br />H °
<br />°
<br />°
<br />a °d
<br />SLOPE
<br />d n
<br />SHOWER SEAT
<br />SELF-ADHER
<br />WINDOW UNIT FLASHING REQUIREMENTS
<br />DOOR ROUGH OPENING
<br />SLOPE
<br />0.3 in: 12.0 in R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />(0.6 cm : 30.5 cm) include flashing as described in Section R703.4. A water -resistive barrier is described as a material behind an exterior wall covering that is
<br />- 3/4"-1" BEAD of CONSTR. intended to resist liquid water that has penetrated behind the exterior covering from further intruding Into the exterior wall assembly. An
<br />ADHESIVE TO BE APPLIED UNDER SELF -ADHERED FLASHING q p g g y
<br />THRESHOLD OF DOOR AND exterior wall covering is described as a material or assembly of materials applied on the exterior side of exterior walls for the purpose of
<br />RETURN UP JAMB 6". USE LIQUID
<br />NAIL BRAND OR EQUAL WEATHER EXTERIOR providing a weather -resistive barrier, insulation, or for aesthetics, including but not limited to, veneers, siding, exterior insulation and finish
<br />PROOF CAULKING CEMT. FIN. systems, architectural trim and embellishments such as cornices, soffits, and fascias.
<br />SELF -ADHERED FLASHING BUILDING PAPER
<br />WIRE LATH R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />SUBFLOOR other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied
<br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less
<br />than 6 inches (152 mm). The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and
<br />RIM JOIST building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />V11
<br />R703.7.3 Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based sheathing, shall
<br />1 include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The individual
<br />2 v AO layers shall be installed independently such that each layer provides a separate continuous plane and any flashing (installed in accordance
<br />with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance equal to or greater
<br />SELF -ADHERED FLASHING than that of 60-minute Grade D paper and is separated from the stucco by an intervening, substantially nonwater-absorbing layer or
<br />1 CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER 1 designed drainage space.
<br />MECHANICALLY FASTEN IF RUBBERIZED ASPHALT
<br />RUBBERIZED R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into the wall
<br />INSTALL SELF -ADHERED NEEDED IN CORNERS ASPHALT ADHESIVE ADHESIVE 9 pp 9 PP g p rY
<br />FLASHING JAMB &HEAD THROUGH SELF -ADHERED cavity or penetration of water to the building structural framing components. Self -adhered membranes used as flashing shall comply with
<br />FLASHING, SEE FLASHING SELF -ADHERED FLASHING AAMA 711. All exterior fenestration products shall be sealed at the juncture with the building wall with a sealant complying with AAMA 800 or
<br />FLANGED WINDOW
<br />(SEE DETAIL WP01) ASTM C920 Class 25 Grade NS or greater for proper joint expansion and contraction, ASTM C1281, AAMA 812, or other approved standard
<br />SCORED as appropriate for the type of sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The flashing
<br />RELEASE PAPER shall extend to the surface of the exterior wall finish. Approved corrosion resistant flashings shall be installed at the following locations:
<br />SELF -ADHERED FLASHING, r (BEFORE FOLDING, SCORE 1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />RELEASE PAPER TO EXPOSE
<br />EXTENDAMINIMUM6" ADHESIVE AS SHOWN) finish or to the water -resistive barrier complying with Section 703 2 for subsequent drainage Mechanically attached flexible flashings
<br />VERTICALLY FROM
<br />BOTTOM OF
<br />THRESHOLD
<br />rem
<br />:LF-ADHERED FLASHING
<br />,TCH
<br />HERED FLASHING
<br />1
<br />2
<br />4
<br />5
<br />SELF -ADHERED FLASHING
<br />INSIDE CORNER
<br />Ground (o-
<br />SELF -ADHERED FLASHING FOUNDATION WEEP SCREED
<br />OUTSIDE CORNER , •
<br />STRIP OF SAF
<br />I- DRAINAGE PLANE WRB
<br />LU
<br />> BOND BREAK WRB
<br />m
<br />> I \ SF LATH
<br />�I WRAP DP WRB ONTO
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />3-1/2" INCH FLANGE
<br />a a II'
<br />a d PLASTER STOP THIS GAP IS A RESULT OF
<br />NATURAL SHRINKAGE.
<br />CO DO NOT SEAL.
<br />_ � CONTINUOUS BACKER
<br />W
<br />LU ROD & SEALANT DRIP SCREED PLASTIC
<br />w ACCESSORY
<br />Q LU
<br />w
<br />� 0 A
<br />_12
<br />SOFFIT/CANTILEVER
<br />Water Resistant Barrier
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF) O
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB) - -
<br />BOND BREAK WEATHER RESISTANT BARRIER - !
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHING,'OSB', PLYWOOD, DENSGLASS S\1m�Z
<br />kSTER STOP ^
<br />NTINUOUS BACKER ROD /1
<br />EALANT
<br />MENTITIOUS FINISH
<br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />following:
<br />1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or
<br />details are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be
<br />2 sealed or sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier
<br />for subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />5 1.2. In accordance with the flashing design or method of a registered design professional.
<br />4 1.3. In accordance with other approved methods.
<br />6 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMAMDMA
<br />400.
<br />7 2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />• 3. Under and at the ends of masonry, wood or metal copings and sills.
<br />4. Continuously above all projecting wood trim.
<br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6. At wall and roof intersections.
<br />7. At built-in autters.
<br />2AL FRAMING
<br />RAL SHEATHING
<br />3AF
<br />PLANE WRB
<br />AK WRB
<br />f HESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />Cement
<br />Plaster
<br />over block
<br />1 st floor
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />-7/16" O.S.B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />1 1/2"to 2"
<br />Above Roof
<br />Sheathing
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1 /2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />T=%
<br />Jj f;
<br />i
<br />i/
<br />i
<br />0
<br />N
<br />O
<br />N
<br />o_
<br />0
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifications contained within these
<br />drawings comply with the 2017
<br />Florida Building
<br />Code -
<br />Residential 6th Edition. Engineer's signature and seal is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineer's signature and seal.
<br />N
<br />W
<br />Q
<br />`t EE
<br />o �
<br />8.Cq
<br />co ,ppipp
<br />V
<br />p
<br />mac'
<br />miK
<br />'
<br />Cou_
<br />J
<br />M
<br />a
<br />N (� D
<br />a:MM
<br />U J iL
<br />W y
<br />J W W
<br />UJ
<br />a a. ix
<br />28-
<br />� Om O
<br />7 mSN(O
<br />m
<br />LLWin2pjQi
<br />Z
<br />Lo C7 Z
<br />Ja
<br />O
<br />W
<br />N
<br />OU
<br />U J
<br />❑�❑
<br />0
<br />0 M-
<br />Z N co
<br />z C>_
<br />0
<br />z n
<br />Q �
<br />U)
<br />J
<br />a N
<br />Willa
<br />to
<br />z
<br />�(1)CD
<br />4-1
<br />(13
<br />U
<br />w
<br />O
<br />w g
<br />Ln
<br />c
<br />'..
<br />U
<br />w
<br />ai ..
<br />_
<br />c Cn
<br />2 a
<br />�0
<br />N Ol
<br />soo
<br />o
<br />M
<br />y
<br />w
<br />M
<br />0
<br />i
<br />LJL
<br />Q E
<br />O
<br />i i
<br />oo
<br />"'�
<br />> o
<br />as
<br />z®
<br />❑a
<br />E: V
<br />OE
<br />°
<br />a
<br />_°
<br />O
<br />Z-
<br />N
<br />i
<br />p
<br /><om0
<br />E Z
<br />�t
<br />p
<br />C
<br />-
<br />z
<br />x
<br />U
<br />`=m
<br />O
<br />oZ
<br />Z
<br />Z
<br />cu
<br />J
<br />a °
<br />aw
<br />Z
<br />U)
<br />8 E
<br />go
<br />a
<br />m
<br />W2
<br />oLL
<br />r�
<br />x3
<br />oo
<br />v
<br />o.
<br />zla
<br />o-
<br />o 3
<br />I*
<br />m
<br />W
<br />cc
<br />',
<br />O
<br />�
<br />'-
<br />T
<br />Oi
<br />L�
<br />o
<br />(D
<br />m
<br />C CD
<br />d.
<br />T
<br />O
<br />O
<br />_J
<br />LO
<br />O
<br />r,
<br />M
<br />oo rn
<br />�-
<br />a;
<br />m
<br />T
<br />N
<br />Z
<br />Z
<br />E O
<br />E
<br />a
<br />@
<br />a
<br />U
<br />Q p
<br />JOB
<br />NO:
<br />20-6579
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />W P
<br />
|