Laserfiche WebLink
r <br />n <br />c <br />BC <br />12 <br />5� <br />!� — -— — --- ----1e:r�w� • • <br />.�+i PP__ <br />TEXTURED BAND <br />oaoo ■ ooa ��� ��� ' <br />I—N <br />j I ■ ■ <br />i—1 M0 il I�IFMIFMl <br />FRONT ELEVATION — Al <br />16-0" RIDGE VENT <br />3'-0 RIDGE VENT <br />12 <br />�5 <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />.G.C. VERIFY ROOF PITCH" <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />"ELECTRICAL SPECIFICATION NOTES" <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7116" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />T.O.P. <br />T.O.M. <br />-- — �-o-�—— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — <br />1, HDRHGT. <br />01 �10 —811 <br />TEXTURED _ o <br />3 —0„ CEMENTICIOUS O <br />FINISH ON C.M.U. o0 00 <br />(TYP. ) <br />Zo <br />25 SH 25 SH <br />---------------------------------------------------------------------------------------------------------------------------F.FL. <br />LEFT ELEVATION — Al <br />• 1 /4"=1' <br />. <br />41, <br />ROFES�3 <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />W <br />Q <br />C) <br />E <br />M 8 # <br />C-, N N J <br />6 J LL <br />1: ■ <br />Nt0_°r°v w a- <br />M v LL ° <br />ei �[ <br />�u-ii a w <br />Z <br />J XO, <br />O0 <br />A: f0 _ S <br />t".o_ 0 O <br />�mNco <br />W <br />W <br />mJ <br />6jO' d a <br />Z <br />LL <br />a <br />N M Z tY D 0 <br />tJ <br />v 0 0 _J W <br />_. Z <br />❑❑❑ <br />U' � <br />z N M <br />z <br />c § <br />d <br />z <br />aN <br />Tom• <br />- <br />(>3 <br />w , <br />o .� <br />V <br />0 <br />w s <br />+� <br />(� <br />r— to <br />8 <br />t <br />�' <br />¢ o <br />• <br />o <br />w <br />Z <br />M <br />z <br />o <br />a <br />� <br />LL_ <br />Eg <br />zffi <br />oLL <br />> <br /><� <br />=® <br />E UO <br />(a <br />w� <br />mO <br />❑a <br />xU <br />�¢ <br />Uo <br />�U <br />o¢ <br />Z <br />o <br />N <br />i <br />p <br />wo <br />ao <br />ww <br />¢ � <br />d <br />. rp <br />c <br />' <br />U <br />' <br />mo <br />o <br />z� <br />Z <br />a�i <br />J <br />m <br /><p <br />'< w <br />�Z <br />N <br />oa <br />no <br />u <br />a <br />O 3 <br />LL <br />mw <br />W <br />_ <br />w <br />r?� <br />oLL <br />J <br />Flo <br />Mill <br />O <br />CD <br />a� <br />�t <br />is <br />i;3 <br />O <br />C O <br />Z <br />Lo <br />m <br />n' <br />W <br />�o <br />0 <br />U <br />(7) <br />i� <br />a <br />C <br />> <br />o <br />0 <br />.0 <br />0 <br />m <br />o <br />o N <br />LO <br />T <br />i 0') <br />00 <br />T <br />E <br />c T <br />c'M <br />'rii <br />o <br />Z <br />Z <br />E <br />E <br />C <br />d <br />U J <br />Q <br />J <br />JOB <br />NO: <br />21-1072 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.1 <br />