Laserfiche WebLink
12 <br />5� <br />12 <br />�5 <br />5'-10" 6-0" <br />T.O.M. <br />— — — — — — — — — — — <br />1'-O" <br />— — — — — — — — — — — — — — — — — — — — — — <br />EXTENDED <br />OVERHANG TO BE <br />CENTERED ON DOOR <br />HDRHGT <br />— <br />TEXTURED o <br />CEMENTICIOUS - ' <br />FINISH ON C.M.U. 01 00 <br />(TYP.) (0 <br />25 SH 25 SH <br />F.FL. <br />REAR ELEVATION — Al <br />s— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - <br />- 1� O <br />TEXTURED <br />C)- CEMENTICIOUS <br />00 00 FINISH ON C.M.U. <br />�0 (TYP.) <br />------------------------------------------- <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />(TYP.) <br />35 SH <br />-- <br />RIGHT ELEVATION <br />— Al <br />1 /4"=1'-0" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />"G.C. VERIFY ROOF PITCH" <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />"ELECTRICAL SPECIFICATION NOTES" <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />\,,\``��a11t411 <br />OWN Nx <br />J <br />r <br />v <br />�<' <br />�U <br />''•.....• <br />rrxi <br />''O�p <br />ROFESS\ <br />\\ <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />(0C. <br />C> N N ILV Y - <br />J i <br />0 <br />W <br />5 G. N it LL W <br />tAfr- � - W 0- <br />Q <br />Z <br />�C0 LLa Y <br />LLLL Wa L S <br />0 0 <br />tm�o <br />mc <br />W <br />Z <br />IL <br />u) CP ' IL <br />If) MZ �tnO <br />- <br />O U <br />Z <br />❑O❑ <br />U C4 M <br />Z N O <br />z O <br />z � � <br />J — <br />aU) $ <br />N <br />z <br />U' o <br />fi <br />1'�• <br />i-� <br />fB <br />U <br />Wo <br />C/� <br />w g <br />c <br />w 8 <br />l/i <br />�N <br />c <br />U ° <br />LL, o <br />E <br />— 8 <br />U o <br />c <br />Q v0D o <br />° <br />N Ol <br />O <br />i� <br />C":)< <br />� � <br />O <br />w <br />z <br />g <br />UL <br />21 E E <br />' <br />❑a <br />Z <br />C <br />O C <br />0 <br />�r <br />a°z <br />ao <br />00 <br />�¢ <br />0¢ <br />az <br />N � <br />N L <br />` (6 <br />o <br />Q O <br />�� <br />m � <br />O <br />Z <br />� <br />� <br />a1 <br />I U <br />°m <br />O¢ <br />Z r- <br />aw <br />cn <br />< <br />z z <br />50 <br />W� <br />N <br />� <br />V <br />oa <br />a o <br />a z <br />�W <br />r- <br />� <br />hi <br />J <br />cF <br />=5 <br />F <br />�O <br />O <br />o� <br />Z¢ <br />a <br />o� <br />U?i <br />O <br />U-) <br />W <br />U <br />� <br />C U <br />> <br />0- <br />^ <br />O <br />m <br />o <br />C.0 <br />Np <br />r <br />0).T— <br />(0 <br />2 N <br />T <br />to-0- <br />/!1 <br />V/ <br />T <br />T <br />M <br />Z <br />E Q <br />M <br />o <br />m <br />it <br />E <br />U � <br />Q 0 <br />C <br />_J <br />JOB <br />NO: <br />21-1072 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.2 <br />