Laserfiche WebLink
TAMPA VER 8 <br />FRAMED WALL WITH OSB SUBSTRATE <br />CMU 4WALL <br />\ TAMPA VER 8 <br />\\ .041)' <br />\ STEP 4&5 <br />UNDERLAYMENT \ UNDERLAYMENT <br />& TIN SHINGLE <br />RECOMMENDED BUT <br />NOT REQUIRED: <br />TIN SHINGLE <br />MIN OFI2"X18", <br />Installed by Roofer. <br />A tin shingle (which <br />protects self - sealing <br />membrane from <br />cladder's knife). <br />TAMPA VER 8 <br />STEP 10 <br />HOUSE -WRAP, <br />\ <br />ENSURE HOUSE -WRAP <br />IS LAPPED ON TOP OF <br />ACCESSORIES & <br />SHINGLE SELF <br />ADHERING MEMBRANE <br />SO HOUSE -WRAP IS <br />LAYERED BELOW THE <br />TARGET FLASHING AT <br />I I I <br />THE BOTTOM. <br />\ I I <br />\ \ \ I I <br />ENSURE SSM/SAM <br />\ , <br />IS DAY -LIGHTED <br />J I <br />AFTER HOUSE - <br />WRAP IS <br />INSTALLED <br />MECHANICALLY FASTEN AS <br />NECESSARY IN CORNERS THROUGH <br />SELF -ADHERED FLASHING <br />WEATHER <br />RESISITIVE <br />BARRIER <br />TAPE <br />(ASSEMBLED <br />WINDOW) <br />WEEP <br />METAL L <br />FLASHING <br />WEATHER <br />/E BARRIER & <br />ARILY SECURE <br />EXTERIOR <br />SHEATHING <br />WOOD FRAME CONSTR. <br />SELF -ADHERED FLASHIr <br />BY LAPPING DOWN -� <br />OVER RIM JOIST AND U <br />WALL BY 6 IN. <br />WEATHER <br />RESISITIVE <br />BARRIER SEAL TOPS OF JOIS <br />UNDER DECKING <br />:D FLASHING (SEE DETAIL WP07) <br />HEAD FLASHING TIE-IN INSTRUXTIONS: <br />1. Cut, fold up & temporarily secure weather resistive <br />barrier above header to allow for flashing installation <br />2. Self -adhered flashing plus head flashing under <br />weather resistive barrier 1 <br />3. Fold weather resistive barrier back over head <br />flashing and seal with tape 2 <br />SELF -ADHERED FLASHING Scale: NTS <br />FLANGED WINDOW WPO 1 <br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER <br />EXTERIOR SHEATHING_-\ <br />REFER TO TECHN <br />LETTER ON CHEM <br />COMPATIBILITY <br />SELF -ADHERED FLASHING i <br />NAILING FLANGE <br />DO NOT FLASH OVER <br />BOTTOM NAILING <br />FLANGE <br />SELF -ADHERED FLASHING <br />HALF ROUND WINDOW <br />SELF -ADHERED <br />z <br />8 <br />TAMPA VER 8 <br />ATTACH AT TOP ONLY <br />TO ALLOW SHINGLING <br />OF WRB. <br />STEP 1 <br />18" X 24" SELF- <br />SEALING <br />MEMBRANE <br />FLASHING, (aka: <br />Target Flashing) <br />Installed by framer <br />EXSTEND PAST <br />WOOD/CMU <br />TRANSITION <br />TAMPA VER 8 <br />REVIEW STEPS 1 - 10 <br />ROOF <br />UNDERLAYMENT <br />ROLLED A MIN OF <br />3-INCHES UNDER L <br />FLASHING <br />KICK -OUT <br />FLASHING <br />APPROVED <br />SEALANT <br />18" X 24" SELF- <br />SEALING <br />MEMBRANE <br />FLASHING <br />(SSM/SAM), Installed <br />by Framer <br />TIN SHINGLE <br />UNDER HOUSE -WRAP, <br />Installed by Roofer <br />CONTROL JOINT <br />WEATHER RESISTIVE <br />BARRIER <br />ROOF <br />RAFTER TAIL <br />DOOR ROUGH OPENING <br />3/4"-1" BEAD OF CONSTR. <br />ADHESIVE TO BE APPLIED UNDER <br />THRESHOLD OF DOOR AND RETURN <br />UP JAMB 6". USE LIQUID NAIL BRAND <br />OR EQUAL WEATHER PROOF CAULKING <br />SELF -ADHERED FLASHING <br />SUBFLOOR <br />RIM JOIST <br />SELF -ADHERED FLASHING <br />EXTERIOR DOOR WITH DECK - SECTION A <br />RUBBERIZED ASPHALT <br />ADHESIVE <br />D FLASHING <br />SCORED <br />RELEASE PAPER <br />W PO4 SELF -ADHERED FLASHING <br />INSIDE CORNER <br />TAMPA VER 8 <br />STEP 2 <br />FRAMER <br />CONSTRUCTS <br />ROOF <br />TAMPA VER 8 <br />STEP 11 <br />CORNER BEAD <br />ACCESSORY <br />TAMPA VER 8 <br />STEP 3 <br />FRAMER <br />CONSTRUCTS <br />ROOF <br />TAMPA <br />STEP 3.1 <br />INBOARD SUB - FASCIA <br />HELD BACK 1 - INCH <br />ED WALL WITH OSB SUBSTRATE <br />/ \\ <br />l� \ <br />CMU WALL \ <br />MID WALL WEEP <br />NTROL JOIN <br />TAMP <br />STEP 3.2 <br />MINIMUM OF 6" <br />SELF -ADHERED / <br />SELF-SEALING <br />MEMBRANE <br />(SSM/SAM) <br />FLASHING, <br />Installed by Housewrap <br />Flashing tape is to be <br />installed behind the SAM <br />target flashing <br />TAMPA VER 8 <br />STEP 9 <br />STUCCO <br />ACCESSORIES, <br />WEEP SCREED & <br />MID WALL <br />CONTROL JOINT, <br />cut and layer the <br />"target" SSM/SAM <br />and tin shingle <br />over the stucco <br />accessory <br />ENSURE SSM IS <br />DAY -LIGHTED <br />AFTER ACCESSORIES <br />ARE INSTALLED <br />Fes. <br />• <br />/••j!+••j•!!1 <br />a+•jai <br />• • • <br />' <br />� I � • <br />• <br />�! <br />!+•• 1�+��+••� <br />WINDOW UNIT <br />SLOPE PRODUCTS DETAILS R609.1 General. This section prescribes performance and construction requirements for exterior <br />0.3 in: 12.0 in windows and doors installed in walls. Windows and doors shall be installed and flashed in accordance <br />(0.6 cm : 30.5 cm) with the fenestration manufacturer's written instructions. Window and door openings shall be flashed <br />SELF -ADHERED FLASHING TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND in accordance with Section R703.4. Written installation instructions shall be provided by the <br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC R703.2 fenestration manufacturer for each window or door. <br />EXTERIOR R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, <br />Detail Instructions <br />CEMT. FIN. complying with ASTM D226 for Type 1 felt or other approved water -resistive barrier shall be applied <br />Refer to the number marked as # in each detail that corresponds to the over studs or sheathingof all exterior walls. Such felt or material shall be applied horizontal) with the <br />BUILDING PAPER numbered items in the list of instructions below: pp y, <br />upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall <br />WIRE LATH be lapped not less than 6 inches (152 mm). The felt or other approved material shall be continuous to <br />1. Install self -adhered flashing in order as shown by numbers the top of walls and terminated at penetrations and building appendages in a manner to meet <br />2. Install flashing and weather resistive barrier to form water shedding laps the requirements of the exterior wall envelope as described in Section R703.1. The water -resistive <br />3. Self -adhered flashing can be substituted for building paper barrier is not required for detached accessory buildings. <br />4. Split the release paper using the ripcord (Split release on demand, embedded in R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner <br />the adhesive layer) - for ease of installation and to minimize scoring cuts to prevent entry of water into the wall cavity or penetration of water to the building structural framing <br />5. Remove all release paper per standard installation instructions and adhere to components. Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior <br />fenestration products shall be sealed at the juncture with the building wall with a sealant complying <br />1 substrate using a square piece of flashing material (6 x 6 Minimum) with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and <br />6. Fold as shown by arrows contraction, ASTM C1281, AAMA 812, or other approved standard as appropriate for the type of <br />2 O 7. Angle of corner may vary, adjust folding of the flashing accordingly to fit tight sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714 The <br />WP02SELF -ADHERED FLASHING <br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER <br />cucnTurnlr� <br />MECHANICALLY FASTEN AS <br />NECESSARY IN CORNERS THROUGH <br />SELF -ADHERED FLASHING <br />2 <br />5 <br />SELF -ADHERED FLASHING <br />4 <br />6 <br />3" MIN <br />7 <br />to corner flashing shall extend to the surface of the exterior wall finish. Approved corrosion resistant flashings <br />8. Mechanically fasten as necessary shall be installed at the following locations: <br />W PO 1. 1.Exterior window and door openings. Flashing at exterior window and door openings shall <br />extend to the surface of the exterior wall finish or to the water -resistive barrier complying <br />with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings shall comply <br />with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with <br />one or more of the following: <br />1. 1.1.The fenestration manufacturer's installation and flashing instructions, or for applications not <br />i addressed in the fenestration manufacturer's instructions, in accordance with the flashing <br />3% TO 5% SLOPE manufacturer's instructions. Where flashing instructions or details are not provided, pan flashing shall <br />TOWARDS SHOWER SIDE be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or sloped in <br />such a manner as to direct water to the surface of the exterior wall finish or to the water resistive <br />SELF -ADHERED FLASHING barrier for subsequent drainage. Openings using pan flashing shall incorporate flashing or protection <br />PATCH at the head and sides. <br />SELF -ADHERED FLASHING <br />WP06 SELF -ADHERED FLASHING <br />OUTSIDE CORNER <br />2. 1.2.In accordance with the flashing design or method of a registered design professional. <br />SHOWER 3. 1.3.In accordance with other approved methods. <br />SIDE 4. 1.4.In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA <br />300 or FMA/AAMA/WDMA 400. <br />2. 2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with <br />1 projecting lips on both sides under stucco copings. <br />3. 3.Under and at the ends of masonry, wood or metal copings and sills. <br />2 2x RIPPED AS <br />NEEDED 4. 4.Continuously above all projecting wood trim. <br />4 1/2" OSB FLITCH 5. 5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame <br />S PLATES construction. <br />6. 6.At wall and roof intersections. <br />7. 7.At built-in gutters. <br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW <br />W PO pO SHOWER CURB DETAIL W P i1 GENERAL FLASHING AND WATERPROOFING METHODS TO BE USED. <br />s <br />DAVISJ BEWS <br />DESIGN GROVP <br />150 STATE STREET FAST <br />OLDSMAR, FLORIDA 34677 <br />813 .925.1300 TEL <br />813.925.1800 FAX <br />W W W.DAVISBEWSCOM <br />TAMPA • DENVEIfZ <br />EST. 1994 <br />O <br />O <br />Z NO <br />14 C:) <br />O ��-' ^ <br />H M O <br />G j f0 Lt <br />N O <br />Q LL <br />�M <br />Ce U Q00 <br />Zfu <br />WC:)w <br />J � <br />J <br />OZ <br />0 <br />w� <br />za <br />a� <br />�a <br />w ¢ C <br />(AI <br />Ezg0 <br />0 <br />F 5ZZ <br />C� <br />Q <br />a0o <br />81 <br />U W �_ N <br />mzo <br />w <br />Q <br />O(n <br />Z0 <br />rU <br />�z <br />z <br />w <br />g <br />Z <br />D <br />0 <br />� <br />I� <br />QJ <br />o <br />U <br />Q <br />D <br />Z <br />0 W <br />- � <br />W <br />,�-i <br />Q <br />Q <br />� W <br />Z <br />Z <br />U <br />z <br />z p <br />LU <br />Z <br />_0U <br />�- <br />H <br />U <br />Z <br />Q <br />00 <br />Z <br />o- <br />W <br />rn <br />w <br />kD m <br />SCALE : AS <br />NOTED <br />DATE : 10-19-2018 <br />VERSION NO. <br />100 <br />SHEET NO. <br />DT8 <br />-1717F ly -- <br />