|
System No. C-AJ-1259
<br />F Rating - 3 Hr
<br />T Rating - 0 Hr
<br />Section A -A
<br />1. Floor or Wall Assembly -Min 4-1/2 in. thick reinforced lightweight or normal weight (100-150 pcf) concrete. Floor may also be
<br />constructed of any min 6 in. thick UL Classified hollow -core Precast Concrete Units*. Wall may also be constructed of any UL
<br />Classified Concrete Blocks*. Max diam of opening is 7 in.
<br />See Concrete Blocks (CAZT) and Precast Concrete Units (CFTV) categories in the Fire Resistance Directory for names of
<br />manufacturers.
<br />2. Through Penetrants - One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the
<br />firestop system. The annular space between the pipe, conduit or tubing and the periphery of the opening shall be a min of 0 in.
<br />(point contact) to a max of 3 in. Pipe, conduit or tubing to be rigidly supported on both sides of floor or wall assembly. The
<br />following types and sizes of metallic pipes, conduit or tubing may be used:
<br />A. Steel Pipe - Nom 6 in. diam (or smaller) Schedule 10 (or heavier) steel pipe.
<br />B. Iron Pipe - Nom 6 in. diam (or smaller) cast or ductile iron pipe.
<br />C. Conduit - Nom 4 in. diam (or smaller) steel electrical metallic tubing or steel conduit.
<br />D. Copper Tube - Nam 4 in. diam (or smaller) Type L (or heavier) copper tube.
<br />3. Forming Material - (Optional, Not Shown) - Mineral wool batt packing material or polyurethane backer rod friction fitted into
<br />opening and recessed from floor or wall surfaces as required to accommodate required thickness of fill material.
<br />4. Fill, Void or Cavity Material* - Sealant - Min 1/2 in. thickness of fill material applied within the annulus, flush with both
<br />surfaces of floor or wall. At the point contact location between penetrating item and concrete, a min 1/4 in. thick bead of fill
<br />material shall be applied at the concrete/penetrating item interface on both sides of floor or wall.
<br />SPECIFIED TECHNOLOGIES INC - SpecSeal Series SSS Sealant or SpecSeal LCi Sealant
<br />*Bearing the UL Classification Mark
<br />Specified Technologies Inc. 210 Evans Way Somerville, NJ 08876
<br />Reproduced courtesy of Underwriters Laboratories, Inc.
<br />Created or Revised: January 2, 2009 STI y UL
<br />C-AJ-1259
<br />(800)992-1180 - (908)526-8000 - FAX (908)231-8415 - E-Mail: - Website:www.stifirestop.com PAGE 1 OF 1
<br />System No. W-L-1079
<br />F Ratings - 1 and 2 Hr (See Item 1B)
<br />T Rating - 0 Hr
<br />L Rating At Ambient - Less Than 1 CFM/sq ft
<br />L Rating At 400 F - Less Than 1 CFM/sq ft
<br />A
<br />3A
<br />3B
<br />3(
<br />A
<br />Oeciivn H-A
<br />1. Wall Assembly - The 1 or 2 hr fire -rated gypsum board/stud wall assembly shall be constructed of the materials and in the
<br />manner described in the individual U300 or U400 Series Wall or Partition Design in the UL Fire Resistance Directory and shall
<br />include the following construction features:
<br />A. Studs - Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom 2 by 4 in.
<br />lumber spaced 16 in. OC with nom 2 by 4 in. lumber end plates and cross braces. Steel studs to be min 3-5/8 in. wide and
<br />spaced max 24 in. OC.
<br />B. Gypsum Board* - 5/8 in. thick, 4 ft wide with square or tapered edges. The gypsum board type, thickness, number of
<br />layers, fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire
<br />Resistance Directory. Max diam of opening is in wood stud walls is 13 in. Max diam of opening in 'steel stud walls is 16 in.
<br />The hourly F rating of the firestop system is equal to the hourly fire rating of the wall assembly in which it is installed.
<br />2. Through Penetrant - One metallic pipe or conduit to be installed either concentrically or eccentrically within the firestop
<br />system. The annular space between pipes or conduits and periphery of opening shall be min 0 in. (point contact) to max 3 in.
<br />Pipe or conduit to be rigidly supported on both sides of wall assembly. The following types and sizes of metallic pipes or
<br />conduits may be used:
<br />A. Steel Pipe - Nom 12 in. diam (or smaller) Schedule 10 (or heavier) steel pipe.
<br />B. Iron Pipe - Nom 12 in. diam (or smaller) cast or ductile iron pipe.
<br />C. Conduit - Nom 4 in. diam (or smaller) electrical metallic tubing, nom 6 in. diam (or smaller) steel conduit or nom 1 in. diam
<br />(or smaller) flexible steel tubing.
<br />D. Copper Pipe Nom 6 in. diam (or smaller) Regular (or heavier) copper pipe.
<br />E. Copper Tube - Nom 6 in. diam (or smaller) Type L (or heavier) copper tube.
<br />-_ Specified Technologies Inc. 210 Evans Way Somerville, NJ 08876
<br />Reproduced courtesy of Underwriters Laboratories, Inc.
<br />STI Created or Revised: January 2,2009 UL
<br />W-L-1079
<br />(800)992-1180 - (908)526-8000 - FAX (908)231-8415 - E-Maihechserv@stifirestop,com - Website:www,stifirestop.com PAGE 1 OF 2
<br />0 ELECTRICAL FIRE iv4TING DETAILS
<br />NOT TO SCALE
<br />STUB -OUT CONDUIT ABOVE
<br />CEILING. PROVIDE AN
<br />INSULATED THROAT
<br />CONNECTOR AT END OF
<br />CONDUIT
<br />PROVIDE PULL WIRE FOR DATA
<br />AND PHONE TECH.
<br />HARD CEILING
<br />DROP CEILING
<br />1) 1" EMT EMPTY CONDUIT
<br />4x4x2-l/8" DEEP JUNCTION BOX OOR$
<br />WITH PLASTER RING. MOUNTING
<br />HEIGHT 10" ON CENTER
<br />4x4x2-1/8" DEEP JUNCTION BOX TV
<br />WITH PLASTER RING. MOUNTING
<br />VERIFY HEIGHT FOR TV
<br />WALL
<br />FLOOR
<br />OWt iNIUNICATION OUTLET DETAIL AND SCHEDULE
<br />SCALE: NOT TO SCALE
<br />PANEL
<br />LA
<br />EXISTING
<br />FLUSH M_YjNED
<br />120.208 VOLT 3 PHASE
<br />4 W IRE WITH GROU` )
<br />NOTES
<br />CKT,
<br />DESCRIPTION
<br />NO.
<br />2
<br />I
<br />RECEPTACLE RM 4, 5,. 6,
<br />2
<br />3
<br />RECEPTACLE R'\S 45. 6, 7
<br />2
<br />5
<br />RECEPTACLE R-M 4z 4.6,?
<br />2
<br />RECEPTACLE R_i �;, 26
<br />2
<br />9
<br />RECEPTA CLE RM 25; 26
<br />2
<br />11
<br />RECEPTACLE �Jv_`�S RRR I
<br />2
<br />13
<br />RECEPTACLES PROCEDURE K
<br />2
<br />15
<br />RECEPTACLES BATH EAA.II =S I
<br />2
<br />1'
<br />RECEPTACLES E A\I »
<br />19
<br />RECEPTACLES r,_ AN't ' 11
<br />2
<br />2i
<br />RECEPTACLES E` I,'I =10:11
<br />2
<br />23
<br />RECEPTACLE E NURSE STATIO
<br />5
<br />2:;
<br />AU'TODOO
<br />5
<br />2?
<br />EF 4.;A7
<br />2
<br />N
<br />_
<br />SPARE
<br />5
<br />31
<br />B2-B
<br />5
<br />33
<br />5
<br />3;
<br />-
<br />2
<br />3?
<br />EXAM 123, 125 R-N-1S
<br />5
<br />39
<br />AUTO DOOR PATIE_*.T BR
<br />1
<br />41
<br />LIGHTING
<br />BREAKER
<br />RIP
<br />POLE
<br />VOLT
<br />A
<br />20
<br />1
<br />120
<br />940
<br />900
<br />20
<br />1
<br />120
<br />"o
<br />1
<br />120
<br />_
<br />20
<br />1
<br />120
<br />900
<br />goo
<br />20
<br />1
<br />120
<br />20
<br />1
<br />120
<br />20
<br />1
<br />12o
<br />900
<br />900
<br />20
<br />1
<br />120
<br />20
<br />1
<br />120
<br />20
<br />1
<br />120
<br />goo
<br />goo
<br />20
<br />1
<br />120
<br />20
<br />1
<br />1,20
<br />20
<br />1
<br />120
<br />1200 1
<br />1200
<br />20
<br />1
<br />120
<br />20
<br />1
<br />Io
<br />20
<br />3
<br />208
<br />1003 1
<br />1200
<br />B
<br />C
<br />90o
<br />goo
<br />goo
<br />goo
<br />900
<br />900
<br />goo
<br />90o
<br />goo
<br />goo
<br />goo
<br />goo
<br />904
<br />900
<br />'
<br />900
<br />goo
<br />goo
<br />1200
<br />'000
<br />goo
<br />20 1 120 1080 2000
<br />20 1 120 1200 2000
<br />20 1 124 Io00 2000
<br />CON NT_CTED VA 14880 14400 1330C
<br />Si'STIM VOLTS 124'208V, 3 PHASE
<br />13PIA IS ] VD.5z 1?,1 1?.R t 11
<br />BREAKER
<br />OLT POLE TRI
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 1 20
<br />120 I 20
<br />120 1 20
<br />124 1 20
<br />120 1 20
<br />120 1 20
<br />208 3 30
<br />NOTES
<br />LOAD TIDE
<br />CONTNECTED
<br />NEC D$MANTD
<br />DEMAND LOAD
<br />1
<br />LIGHTING
<br />7600
<br />1.25
<br />9500 VA
<br />16340 VA
<br />0 VA
<br />0 VA
<br />123oo VA
<br />0 VA
<br />0 VA
<br />38140 VA
<br />2
<br />RECEPTACLES
<br />22680
<br />1
<br />?
<br />AIRCONDITIOINING
<br />a
<br />0
<br />4
<br />HEATING
<br />0
<br />0
<br />5
<br />DISC. NON -CONTINUOUS
<br />12300
<br />1
<br />6
<br />CONTINUOUS
<br />0
<br />1.25
<br />KITCHEN
<br />0
<br />0.65
<br />TOTAL
<br />124"208T'_ 3 PHA
<br />SE
<br />i 06 Ah9 i'S
<br />MLO
<br />k1
<br />2
<br />RECPT.DESK ---1— 81 2
<br />RECEPT EYAM VLOUNGE GFI I 101 2
<br />RECEPTACLES EXANI ;i�2 1 121 2
<br />RECEPT. RECEPTION FILES
<br />181
<br />2
<br />RECEPTACLES EXAM �4, 5
<br />20
<br />2
<br />RECTPTA CL.ES E?L4M 45, 6
<br />L,
<br />2
<br />RECEPTACLES EXAM #3
<br />24
<br />2
<br />LIGHTING
<br />26
<br />` I
<br />LIGHTING
<br />321
<br />1
<br />BATH SENSORS WOMEN S'RR
<br />34
<br />1
<br />BA TH SE SORS WCWENS RR
<br />36
<br />1
<br />TERMINAL BOX
<br />38
<br />5
<br />-----
<br />40
<br />5
<br />NOTES ( }
<br />PANEL IS LOCATED IN THIS AREA. DEMOLISHED aRCUITS
<br />:VIAYBERE-USED.PROVIDEI mo'DRECTORYUPON
<br />COMPLETION
<br />PANEL
<br />LB
<br />EXISTING
<br />FLi.:SH MOUINTED
<br />120/20S VOLT 3 PHASE
<br />4 FIRE WITH GROL ND
<br />225A MLO
<br />NEMA I
<br />22,000AIC
<br />NOTES
<br />CKT_
<br />DESCRIPTION
<br />BREAKER
<br />A
<br />B
<br />C
<br />BREAKER
<br />DESCRIPTION
<br />CKT.
<br />NOTES
<br />NO.
<br />TRIP
<br />POLE
<br />VOLT
<br />VOLT
<br />POLE
<br />TRIP
<br />NO.
<br />2
<br />I
<br />PECEPTFILE EXA4 2
<br />20
<br />1
<br />120
<br />940
<br />6220
<br />208
<br />100
<br />PANIC LBE
<br />2
<br />3
<br />RECEPTACLES EXA, M =3. 4
<br />20
<br />1
<br />120
<br />900
<br />5860
<br />--------'"$)
<br />4
<br />2
<br />2
<br />5
<br />REC'EPTACLESEXAMi=1.2
<br />20
<br />1
<br />120
<br />900
<br />5200
<br />-------- 0*'
<br />6
<br />2
<br />2
<br />-
<br />RECEPTACLES EXAM 8
<br />20
<br />1
<br />120
<br />900 940
<br />120
<br />1
<br />20
<br />RECEPT. IFT ROOM
<br />81
<br />2
<br />2
<br />9
<br />RECEPTAC'LESENAM 6, i
<br />20
<br />1
<br />120
<br />900
<br />900
<br />120
<br />1
<br />20
<br />RECEPT. LAB STATIONS
<br />101
<br />2
<br />2
<br />11
<br />RECEPTACLES E tiANI =5, 6
<br />20
<br />1
<br />120
<br />900
<br />900
<br />120
<br />1
<br />20
<br />RECEPT. LAB STATIONS
<br />12
<br />2
<br />2
<br />13
<br />RECEPTACLES EZA\I #2
<br />�0
<br />1
<br />1.4
<br />900 900
<br />I-0
<br />1
<br />:0
<br />RECEPT. I.V. ROOM
<br />14
<br />,
<br />2
<br />15
<br />RECEPTACLES E�1M .=2
<br />20
<br />1
<br />124
<br />900
<br />1200
<br />120
<br />1
<br />20
<br />LIGHTING
<br />16
<br />1
<br />2
<br />1'
<br />RECEPTA CZES CASHIER
<br />20
<br />1
<br />120
<br />900
<br />1 1200
<br />120
<br />1
<br />20
<br />LIGHTING
<br />Is
<br />1
<br />2
<br />19l
<br />RECEPT_ NURSE STATION
<br />20
<br />1
<br />120
<br />900 1200
<br />120
<br />1
<br />30
<br />LIGHTING
<br />20
<br />1
<br />2
<br />1 211
<br />RECMEDSTOILETS
<br />24 20
<br />1
<br />1-0
<br />900
<br />1244
<br />120
<br />1
<br />20
<br />LIGHTLNG
<br />?2
<br />I
<br />2111
<br />REC NIEDS-LIGHTING
<br />20 20
<br />1
<br />120
<br />900
<br />1000
<br />208
<br />3
<br />24
<br />V H4
<br />241
<br />5
<br />c
<br />25
<br />HP-1
<br />3o
<br />2
<br />208
<br />2000 1000
<br />------ -
<br />261
<br />5
<br />5
<br />23
<br />------ -
<br />2000
<br />1000
<br />--------
<br />28
<br />5
<br />5
<br />29
<br />OTOSCOPE R-M 3 DEB.
<br />20
<br />1
<br />120
<br />1200
<br />1200
<br />120
<br />1
<br />20
<br />AUTODOORS
<br />30
<br />5
<br />5
<br />+1
<br />B -2-2B 2-3. 32-Y
<br />30
<br />3
<br />208
<br />2000 1000
<br />120
<br />1
<br />20
<br />LOBBY LIGHTING
<br />32
<br />1
<br />5
<br />33
<br />-----
<br />20oo
<br />1000
<br />120
<br />1
<br />20
<br />EF 8, 9, 10
<br />34
<br />5
<br />5
<br />35
<br />2000
<br />1000
<br />120
<br />1
<br />20
<br />VAV Cc' .IETROL
<br />36
<br />5
<br />5
<br />37
<br />HEATER PNTERNA.I,-NIEDICI:NE
<br />50
<br />3
<br />20S
<br />3400 1000
<br />20S
<br />3
<br />20
<br />B-120
<br />38
<br />5
<br />5
<br />39
<br />---------
<br />3000
<br />1444
<br />--------
<br />40
<br />5
<br />5
<br />41
<br />---------
<br />_moo 1000
<br />---------
<br />42
<br />5
<br />CONNECTED
<br />S1-STEM
<br />PHA
<br />VA
<br />VOLTS
<br />SE A MPS
<br />22820
<br />22760
<br />21300
<br />I-s
<br />NOTES { )
<br />'. PROVIDE NEW BREAKER TO MATCH EXISTING
<br />"". RELOCATE EXISTIING CIRCUIT TO NEW PAINTEL LBB
<br />120.208V, 3 PHASE
<br />190
<br />190
<br />NOTES
<br />LOADTYPE
<br />CONNECTED
<br />NEC DEMAND
<br />DE_h1AN'DLOAD
<br />I
<br />LIGHTING
<br />5800
<br />1.25
<br />-250 VA
<br />20840 VA
<br />0 VA
<br />0 VA
<br />294o0 VA
<br />0 VA
<br />0 VA
<br />57490 VA
<br />2
<br />RECEPTACLES
<br />31680
<br />1
<br />3
<br />AIRCOINDITIOMNG
<br />0
<br />0
<br />4
<br />HEATING
<br />0
<br />0
<br />5
<br />MISC. NON -CONTINUOUS
<br />29400
<br />1
<br />6
<br />CONTINUOUS
<br />0
<br />1.25
<br />7
<br />KITCHEN
<br />0
<br />0.65
<br />TOTAL
<br />120`208V, 3 PHASE
<br />I
<br />160 AM PS
<br />0 EXISTING ELECTRICAL PANEL SCWEDULES
<br />SCALE: NOT TO SCALE
<br />ELECTRICAL SPECIFICATIONS:
<br />THE WORK UNDER THE REQUIREMENTS OF THESE SPECIFICATIONS SHALL BE
<br />OIN CONFORMANCE WITH THE LATEST EDITION OF THE NATIONAL ELECTRICAL
<br />CODE. THE INSTALLATION SHALL ALSO COMPLY WITH ALL APPLICABLE
<br />RULES AND REGULATION6 OF LOCAL AND STATE LAWS AND ORDINANCES.
<br />OALL ELECTRICAL EQUIPMENT SHALL HAVE UL LABEL AND SHALL BE OF
<br />SPECIFICATION GRADE:;-
<br />POWER DISTRIBUTION HOUSE PANEL50ARD: PROVIDE DEAD -FRONT,
<br />OSAFETY -TYPE POWER DI_t5TRI5UTI0N PANELBOARDS AS INDICATEDi WITH
<br />PANEL50ARD SWITCH140 AND PROTECTIVE DEVICES IN QUANTITIES, RATINGS,
<br />TYPES, AND WITH ARRANGEMENT SHOWNi WITH ANTI -TURN, SOLDERLESS
<br />PRESSURE TYPE MAIN LUG CONNECTORS APPROVED FOR USE WITH COPPER
<br />CONDUCTORS.
<br />®PANEL5OARDS EQUAL TO SQUARE D TYPE "QO". VOLTAGE SHALL BE AS
<br />INDICATED. ACCEPTABLE MFG.t G.E., SIEMENS AND CUTLER -HAMMER
<br />ALL PANELBOARDS SHALL BE CONNECTED, DISTRIBUTED PHASE WITH
<br />OCIRCUIT NUMBERING AS INDICATED ON THE DRAWINGS. F-ANEL50ARDS SHALL
<br />BE NUMBERED WITH ODD NUMBERS ON THE LEFT SIDE OF THE PANEL AND
<br />EVEN NUMBERS ON THE RIGHT SIDE OF THE PANEL.
<br />UNLESS OTHERWISE INDICATED, PROTECTIVE DEVICES SHALL BE MOUNTED
<br />OWITH TOP OF CABINET OR ENCLOSURE 6'-6" ABOVE FINISHED FLOOR, SHALL
<br />BE PROPERLY ALIGNED, AND SHALL BE ADEQUATELY SUPPORTED
<br />INDEPENDENTLY OF THE CONNECTING RACEWAYS. ALL STEEL SHAPES, ETC.,
<br />NECESSARY FOR THE SUPPORT OF THE EQUIPMENT SHALL BE FURNISHED
<br />AND INSTALLED BY THE CONTRACTOR WHERE THE BUILDING STRUCTURE 15
<br />NOT SUITABLE FOR MOUNTING THE EQUIPMENT DIRECTLY THEREON, UNLESS
<br />OTHERWISE INDICATED, ALL BRANCH CIRCUIT PROTECTIVE DEVICES
<br />ENCLOSURES SHALL BE NEMA TYPE 1, GENERAL PURPOSE TYPE. CIRCUIT
<br />PROTECTIVE DEVICES INSTALLED OUTDOORS OR EXPOSED TO THE
<br />WEATHER SHALL HAVE WEATHERPROOF ENCLOSURES, NEMA TYPE "31R" OR
<br />TYPE "4
<br />ALL SAFETY SWITCHES SHALL BE GENERAL DUTY TYPE. SWITCH MECHANISM
<br />OSHALL BE QUICK -MAKE, QUICK -BREAK COVER SHALL BE INTERLOCKED WITH
<br />MECHANISM TO PREVENT OPENING UNLESS SWITCH IS IN THE "OFF" POSITION.
<br />ALL ENCLOSURES SHALL BE PRIMED AND FINISHED TO RESIST RUSTING AND
<br />CORROSION. SWITCHES SHALL BE ITE, GENERAL ELECTRIC, SQUARE-D, OR
<br />CUTLER -HAMMER
<br />OCIRCUIT BREAKERS FOR MOUNTING IN HOUSE PANELBOARD SHALL BE
<br />BOLT -ON OR PLUG IN TYPE, MOLDED PLASTIC CASE, AIR CIRCUIT BREAKER
<br />TYPE_ BREAKERS SHALL HAVE THERMAL MAGNETIC TRIP UNITS AND
<br />MULTI -POLE BREAKERS SHALL HAVE A COMMON TRIP BAR SO THAT THE
<br />TRIPPING OF ONE POLE WILL AUTOMATICALLY TRIP ALL POLES OF THE
<br />BREAKER BREAKERS SHALL BE TRIP FREE AND TRIP INDICATING AND
<br />SHALL HAVE QUICK -MAKE, QUICK -BREAK CONTACTS.
<br />OUPON COMPLETION OF WORK CORRECT ALL PANELBOARD CIRCUIT
<br />DIRECTORY CARDS TO REFLECT 45-5UILT CONDITIONS. PANELBOARD
<br />DIRECTORIES SHALL BE UPDATED WITH TYPEWRITTEN ACCURATE AND
<br />CURRENT INFORMATION BY THE CONTRACTOR AT THE END OF CONSTRUCTION.
<br />DIRECTORIES SHALL REFLECT RECORD CONDITIONS AND INCLUDE CIRCUIT
<br />NUMBER, TYPE AND LOCATION OF LOAD. A SET OF AS -BUILT DRAWINGS
<br />SHALL ALSO BE PREPARED AND TURNED OVER TO THE OWNER
<br />ALL CONDUCTORS SHALL BE THHN/THWN COPPER 012 MIN. AND INSTALLED IN
<br />10 A COMPLETELY ENCLOSED RACEWAY SYSTEM. FEEDERS MAY BE ALUMINUM
<br />WHEN LARGER THAN % AWG
<br />UNLESS SPECIFICALLY NOTED ON DRAWINGS, RACEWAYS SHALL COMPLY
<br />11 WITH THE FOLLOWING:
<br />RACEWAYS EXPOSED TO THE WEATHER OR IN DAMP LOCATIONS
<br />12 SHALL BE SCHEDULE 40 PVC OR GALVANIZED RIGID STEEL WITH
<br />THREADED CONNECTIONS WHEN EXPOSED TO DAMAGE.
<br />RACEWAYS SHALL BE SIZED FOR THE CONDUCTORS INSTALLED,
<br />MINIMUM 1/2%FULL SIZE MC CABLE IS ACCEPTABLE IN DRY LOCATIONS_
<br />13 HOME RUNS TO PANELS TO BE IN CONDUIT.
<br />14 RACEWAYS RUN BELOW GRADE SHALL BE SCHEDULE 40 PVC
<br />ALL METALLIC RACEWAYS SHALL BE MECHANICALLY AND ELECTRICALLY
<br />15 SECURE AT ALL JOINTS AND AT ALL BOXES, CABINETS, FITTINGS, AND
<br />EQUIPMENT.
<br />16 ALL RACEWAYS SHALL BE SECURELY SUPPORTED FROM THE BUILDING
<br />STRUCTURE.
<br />17 ALL RACEWAYS SHALL BE PROVIDED WITH EQUIPMENT GROUND CONDUCTOR.
<br />ALL BOXES SHALL BE RIGIDLY MOUNTED AND SHALL BE EQUIPPED WITH
<br />18 SUITABLE SCREW FASTENED COVERS. OPEN KNOCK -OUTS OR HOLES IN
<br />BOXES SHALL BE PLUGGED WITH A SUITABLE BLANKING DEVICES.
<br />OUTLET BOXES FOR EXPOSED WALL MOUNTING AND OUTDOOR INSTALLATION
<br />1g SHALL BE CAST METAL TYPE "FS" OR "FD" BOXES WITH SUITABLE
<br />GALVANIZED SHEET STEEL COVERS, OR CAST METAL WEATHERPROOF OR
<br />VAPOR TIGHT COVERS WHEN NOTED ON THE DRAWINGS.
<br />UNLESS OTHERWISE INDICATED, ALL CONDUCTORS SHALL BE COPPER NO. 12
<br />20 AWG_ MINIMUM. OR SIZE AS SHOWN ON DRAWINGS. CONDUCTORS SHALL HAVE
<br />TYPE ' 'THHN/THWN' INSULATION.
<br />SPLICES, TAPS AND ATTACHMENT FITTINGS AND LUGS SHALL BE
<br />21 ELECTRICALLY AND MECHANICALLY SECURE AND SOLDERLESS FOR
<br />CONDUCTORS SIZES NO, 8 AWG AND LARGER. THERE SHALL BE PLENTY OF
<br />SLACK CABLE IN BOXES, OUTLETS AND CABINETS TO INSURE THAT THERE IS
<br />NO BINDING AT THE BUSHINGS. ALL LUGS SHALL BE OF THE CORRECT 51ZES
<br />FOR THE CONDUCTORS JOINED AND IN NO CASE SHALL STRANDS BE CUT
<br />FROM A CONDUCTOR IN ORDER. TO FIT THE CONDUCTOR INTO A LUG. TAPING
<br />OF JOINTS SHALL BE WITH VINYL PLASTIC ELECTRICAL TAPE TO SECURE
<br />INSULATION STRENGTH EQUAL TO THAT OF THE CONDUCTORS JOINED.
<br />22 THE INTERIOR ELECTRICAL SYSTEMS SHALL BE COMPLETELY AND
<br />EFFECTIVELY GROUNDED AS REQUIRED BY THE NEC AND AS SPECIFIED
<br />HEREINAFTER.
<br />23 CONTRACTOR SHALL OBTAIN ALL NECE55ARY PERMITS.
<br />THE CONTRACTOR SHALL VERIFY ALL LOCATIONS WITH THE OWNER PRIOR TO
<br />INSTALLATION. THEY SHALL NOT BE CHARGED FOR MINOR LOCATION
<br />®CHANGES PRIOR TO INSTALLATIONS. LOCATIONS ARE APPROXIMATE. (DO
<br />NOT SCALE DRAWINGS).
<br />THESE DRAWINGS ARE DIAGRAMMATIC AND SHOW GENERAL ELECTRICAL
<br />25 LAYOUTS FOR BIDDING PURPOSES ONLY. IT IS THE RESPONSIBILITY OF THE
<br />CONTRACTOR TO PREPARE DETAILED SHOP DRAWINGS AND CONFIRM
<br />SPACE ALLOCATIONS.
<br />THE ELECTRICAL CONTRACTOR SHALL COORDINATE WITH ALL DISCIPLINES
<br />26 FOR ELECTRICAL CONDUIT ROUTING AND EQUIPMENT PLACEMENT. AVOID
<br />INTERFERENCE WITH ARCHITECTURAL AND STRUCTURAL FEATURES SUCH AS:
<br />BEAMS, FOOTINGS, WINDOWS, ETC_ NOTIFY ARCHITECT IMMEDIATELY OF ANY
<br />CONFLICTS,
<br />THE ELECTRICAL CONTRACTOR THE HVAC FOREMAN AND GENERAL
<br />27 CONTRACTOR PROJECT MANAGER SHALL INSPECT 4 REVIEW THE
<br />CONDITIONS, AND SHALL COORDINATE THEIR WORK SO AS TO PROVIDE
<br />ADEQUATE SPACE ALLOWANCE ABOVE CEILING FOR ALL TRADES.
<br />THE PLANS SHOW THE LOCATION OF ALL FIXTURES AND EQUIPMENT AND ARE
<br />28 INTENDED TO DEPICT THE GENERAL INTENT OF THE WORK IN SCOPE, LAYOUT
<br />AND QUALITY OF WORKMANSHIP. THEY ARE NOT INTENDED TO SHOW IN MINUTE
<br />DETAIL EVERY AND ALL ACCESSORIES INTENDED FOR THE PURPOSE OF
<br />EXECUTION OF THE WORK, BUT SHALL BE UNDERSTOOD THAT SUCH DETAILS
<br />WILL BE PART OF THIS WORK.
<br />THE ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL A COMPLETE
<br />29 AND FUNCTIONAL SYSTEM: CONTROLS, AND CONNECTIONS TO NEW SERVICES,
<br />SUPPORTS, AND HARDWARE REQUIRED FOR THE SATISFACTORY OPERATION
<br />OF THE SYSTEM, WHETHER SPECIFICALLY SHOWN OR NOT ON THE DRAWINGS.
<br />WHERE DRAWINGS AND SPECIFICATIONS CONFLICT, IT SHALL BE THE
<br />30 RESPONSIBILITY OF THIS CONTRACTOR TO BRING SUCH CONFLICT TO THE
<br />ATTENTION OF THE ENGINEER FOR CLARIFICATION.
<br />ELECTfRICAL S"'1„150L LEC;END
<br />SYHBOL
<br />DESCRIPTION
<br />, HOUNTING
<br />1 X 4 FLUORESCENT FIXTURE
<br />SEE FIXTURE
<br />LETTER INDICATES TYPE
<br />SCHEDULE
<br />2 X 4 FLUORESCENT FIXTURE
<br />SEE FIXTURE
<br />LETTER INDICATES TYPE
<br />SCHEDULE
<br />SHADING DENOTES FIXTURE WITH EM BATTERY PACK_
<br />SEE FIXTURE
<br />NL' DENOTES FIXTURE UNSWITCHED FOR NIGHT LIGHT
<br />SCHEDULE
<br />FLUORESCENT STRIP FIXTURE
<br />SEE FIXTURE
<br />LETTER INDICATES TYPE
<br />SCHEDULE
<br />FLUORESCENT WALL BRACKET FIXTURE
<br />SEE FIXTURE
<br />LETTER INDICATES TYPE
<br />SCHEDULE
<br />O
<br />PL FLUORESCENT DOWNLIGHT
<br />SEE FIXTURE
<br />LETTER INDICATES TYPE
<br />SCHEDULE
<br />18 EX
<br />EXIT -SHADING DENOTES FACEPLATE LOCATION. LETTER
<br />SEE FIXTURE
<br />--
<br />INDICATES TYPE. PROVIDE ARROWS AS REQUIRED,
<br />SCHEDULE
<br />SINGLE POLE SWITCH (20A-120/217)
<br />48" AFF OR AS
<br />S S3 SO
<br />'3' DENOTES 3-WAY 'O' DENOTES OCCUPANCY SENSOR
<br />NOTED
<br />)=
<br />DUPLEX RECEPTACLE, 125V, 204
<br />18" AFF OR AS
<br />'IG' DENOTES ISOLATED GROUND
<br />NOTED
<br />�
<br />DUPLEX RECEPTACLE, 125V, 20A
<br />16" AFF OR AS
<br />NOTED
<br />W
<br />DUPLEX RECEPTACLE, 125V, 20A
<br />48" AFF OR AS
<br />NOTED
<br />0
<br />QUADRAPLEX RECEPTACLE, 125V, 204
<br />16" AFF OR AS
<br />NOTED
<br />Q
<br />COMBINATION VOICE/DATA OUTLET
<br />15" AFF OR AS
<br />NOTED
<br />TV
<br />T.V_ OUTLET
<br />18" AFF OR AS
<br />NOTED
<br />PANEL50ARD 120/240V
<br />SEE PANEL
<br />SCHEDULE
<br />RACEWAY CONCEALED IN WALL OR ABOVE CEILING
<br />SEE SPECIFICATIONS
<br />HOMERUN TO PANEL. LETTERS INDICATE PANEL,
<br />SEE SPECIFICATIONS
<br />NUMBERS INDICATE CIRCUIT. NOTE: HASH MARKS
<br />INDICATES THE NUMBER OF WIRES EXCLUDING
<br />THE REQUIRED EQUIPMENT GROUND_
<br />/
<br />MOTOR, NUMERAL INDICATES HORSEPOWER
<br />AS NOTED
<br />s
<br />MOTOR RATED SWITCH WITH OVERLOAD
<br />MOUNTED ADJACENT
<br />RELAYS IF REQUIRED.
<br />TO EQUIPMENT
<br />E=h
<br />NON -FUSIBLE SAFETY SWITCH -SIZE AS NOTED
<br />SEE SPECIFICATIONS
<br />FUSIBLE SAFETY SWITCH -SIZE AS NOTED
<br />SEE SPECIFICATIONS
<br />FIRE ALARM DUCT DETECTOR C'R4'DENOTES
<br />MOUNTED IN
<br />OR
<br />S
<br />RETURN AIR 'SA' DENOTES SUPPLY AIR)
<br />HVAC DUCTWORK
<br />®
<br />FAN OR AIR HANDLER SHUTDOWN RELAY
<br />MOUNTED ENT
<br />TO EQUIPMENT
<br />FIRE ALARM VISUAL SIGNAL
<br />00" AFF OR
<br />AS NOTED
<br />Q
<br />FIRE ALARM MANUAL PULLSTATION
<br />45" AFF OR
<br />AS NOTED
<br />FIRE ALARM AUDIBLE/VISUAL SIGNAL. ADA
<br />SO" AFF OR
<br />°
<br />COMPATIBLE
<br />AS NOTED
<br />O
<br />FIRE ALARM SMOKE DETECTOR
<br />ON CEILING OR
<br />AS NOTED
<br />FACP
<br />FIRE ALARM PANEL C'FACP' DENOTES FIRE ALARM
<br />60" AFF OR
<br />FAA
<br />CONTROL PANEL, 'FAA' DENOTES ANNUNCIATOR)
<br />AS NOTED
<br />EX
<br />DENOTES EXISTING DEVICE OR CIRCUIT TO REMAIN
<br />R
<br />DENOTE NEW LOCATION FOR RELOCATED DEVICE
<br />3O O
<br />REFER TO LIKE NUMBERED NOTES
<br />NOTE -ALL MOUNTING HEIGHTS SHOWN ARE TO THE TOP OF THE
<br />DEVICE UNLESS NOTED OTHERWISE.
<br />NOT ALL SYMBOLS APPEAR ON PLANS.
<br />ABBREVIATIONS:
<br />AFF
<br />- ABOVE FINISHED FLOOR
<br />AHU
<br />- AIR HANDLING UNIT
<br />BFG
<br />- BELOW FINISHED GRADE
<br />C
<br />- CONDUIT
<br />CW
<br />- COOL WHITE
<br />DACP
<br />- DOOR ALARM CONTROL PANEL
<br />DN
<br />- DOWN
<br />EF
<br />- EXHAUST FAN
<br />EG
<br />- EQUIPMENT GROUND
<br />ENCL
<br />- ENCLOSURE
<br />EWC
<br />- ELECTRIC WATER COOLER
<br />EWH
<br />- ELECTRIC WATER HEATER
<br />EX
<br />- EXISTING
<br />FCU
<br />- FAN COIL UNIT
<br />FHP
<br />- FRACTIONAL HORSE POWER
<br />FLA
<br />- FULL LOAD AMPERES
<br />G
<br />- GROUND
<br />GFI
<br />- GROUND FAULT INTERRUPTER
<br />HID
<br />- HIGH INTENSISTY DISCHARGE
<br />HORIZ
<br />- HORIZONTAL
<br />IG
<br />- ISOLATED GROUND
<br />LW
<br />- LIGHT WHITE
<br />HP -
<br />HORSEPOWER, HEAT PUMP
<br />HVAC
<br />- HEATING, BENTILATING, AIR CONDITIONING
<br />JB -
<br />JUNCTION BOX
<br />LRA -
<br />LOCKED ROTOR AMPERES
<br />MCB -
<br />MAIN CIRCUIT BREAKER
<br />MLO -
<br />MAIN LUGS ONLY
<br />N -
<br />NEW
<br />NL -
<br />NIGHT LIGHT
<br />OB -
<br />OUTLET BOX
<br />PB -
<br />PULL SOX, PUSH-BUTTON
<br />R -
<br />RELOCATED
<br />RECEPT -
<br />RECEPTACLE
<br />SF -
<br />SUPPLY FAN
<br />SPEC -
<br />SPECIFICATIONS
<br />SWECS -
<br />SMOKE WARNING EMERGENCY CALL SYSTEM
<br />TL -
<br />TWISTLOCK
<br />TTB -
<br />TELEPHONE TERMINAL BOARD
<br />TVTB -
<br />TELEVISION TERMINAL BOARD
<br />UNO -
<br />UNLESS NOTED OTHERWISE
<br />VERT -
<br />VERTICAL
<br />WM -
<br />WATT MISER
<br />WP -
<br />WEATHERPROOF
<br />WW -
<br />WARM WHITE
<br />XFMR -
<br />TRANSFORMER
<br />ELECTRICAL LEGEND ,AND SPECIFICATIONS
<br />SCALE: NOT TO SCALE
<br />REVISIONS
<br />BY
<br />J �
<br />I �
<br />I • v
<br />'U
<br />I— 0
<br />°� o
<br />� x N �
<br />tz Fti U
<br />N a L'" U
<br />• o
<br />ti C'N
<br />it
<br />¢ E `*
<br />¢ - 3
<br />w
<br />0
<br />N a
<br />x
<br />1
<br />��,j •err � �, ` �Q� � �
<br />..
<br />I I PZ s
<br />STATE G1(F Znf/a
<br />ma
<br />uU)
<br />W Z In i k
<br />J
<br />L
<br />o U
<br />Z It
<br />W O LO
<br />V Z M
<br />o J o m cn v
<br />-v
<br />O Q
<br />W
<br />•0
<br />(D Cl) i
<br />cl�0 i LL_
<br />w
<br />O 'M Z •� (�
<br />•aLi
<br />_
<br />mLO
<br />W
<br />M i
<br />00 -C
<br />ZCL
<br />° O — M a�
<br />i J IV
<br />v L`
<br />CL
<br />Date: 08. 13. 13
<br />Scale: AS NOTED
<br />Project Mgr: AAY
<br />Drawn: IIT
<br />Job: 13-46
<br />Sheet
<br />E 1
<br />
|