|
LU
<br />z
<br />v
<br />0
<br />ry
<br />co
<br />C3
<br />1111
<br />co
<br />F_
<br />cn
<br />co
<br />9
<br />f.0
<br />14?
<br />C\11
<br />04
<br />c:)
<br />04
<br />04
<br />r-
<br />LU
<br />F_
<br />cf)
<br />w
<br />P4
<br />co
<br />cq
<br />'T
<br />X
<br />cn
<br />DEVICE MOUNTING HEIGHT REFERENCE (PER NFPA 72)
<br />A/C SUPPLY
<br />VISUAL APPLIANCE MOUNTING HEIGHT CONSIDERATIONS IN SLEEPING ROOMS
<br />OR RETURN
<br />1 MIN DISTANCE IN SLEEPING ROOMS IS 24" (610mm) FROM CEILING TO DIFFUSER THE 4" REQUIREMENT FOR SMOKE DETECTORS HAS
<br />TOP OF LENS FOR 11 OCD STROBES WITHIN 16' OF THE PILLOW BEEN REMOVED FROM THE 2010 EDITION OF NFPA 72
<br />2. 177CD STROBES, USED IN SLEEPING ROOMS, CAN BE WITHIN THE 24"
<br />4 NOTE: MEASUREMENTS
<br />(610mm) MINIMUM DISTANCE FROM THE CEILING. THE HIGHER
<br />3' (M IN) (102mm) SHOWN ARE TO THE
<br />INTENSITY IS TO COMPENSATE FOR A POSSIBLE SMOKE LAYER. (914mm MIN) CEILING CLOSEST EDGE OFTHE
<br />/vx DETECTOR.
<br />FOR CEILING HEIGHTS LESS THAN 86" (2180mm),
<br />THE VISUAL LENS MOUNTING HEIGHT SHALL BE
<br />WITHIN 6" (150mm) OF THE CEILING.
<br />C=
<br />f9FE—
<br />AUDIBLE/VISUAL
<br />& VISUAL ONLY
<br />APPLIANCES
<br />SYNCHRONIZE MORE THAN
<br />TWO APPLIANCES IN ANY
<br />FIELD OF VIEW.
<br />REF. 80" MIN (IBC)
<br />(2032mm MIN)
<br />REF. 96" MAX (IBC)
<br />(2440mm MAX)
<br />ABOVE FINISHED FLOOR
<br />80" MIN (ADA)
<br />80" MIN (NFPA)
<br />TO BOTTOM
<br />NOTE: REFER TO THE PROPER DEVICE
<br />INSTALLATION INSTRUCTIONS
<br />FOR BACKBOX MOUNTING HEIGHT.
<br />AUDIBLE ONLY
<br />96" MAX
<br />(NFPA, ADA)
<br />(2440mm
<br />MAX)
<br />ABOVE FINISHED FLOOR
<br />TO TOP OF LENS
<br />(2032mm
<br />MIN)
<br />(2032mm
<br />MIN)
<br />OF LENS
<br />FINISHED
<br />FLOOR
<br />NFPA 72 AUDIBLE APPLIANCE
<br />6" MIN (152.4mm MIN)
<br />BELOW FINISHED CEILING
<br />"
<br />CEILING MOUNTED
<br />SMOKE/HEAT 4
<br />(1 02mm) 12" (MAX)
<br />DETECTOR
<br />(305mm MAX)
<br />HEAT DETECTORS
<br />90
<br />MIN (2286mm MIN)
<br />ACCEPTED HERE NEVER HERE
<br />ABOVE FINISHED FLOOR
<br />(OTHER MOUNTING HEIGHTS SHALL BE
<br />PERMITTED BY THE AHJ PROVIDING IT
<br />MEETS THE SOUND LEVEL OUTPUT REQUIRED.)
<br />TO EXIT DOOR
<br />5' (MAX.)
<br />(1 524mm)
<br />DOOR
<br />WIDTH
<br />LESS 3"
<br />(76mm)
<br />5"
<br />(1 27mm)
<br />MANUAL
<br />PULL
<br />STATION
<br />FIRE
<br />PHONE MAGNETIC
<br />JACK ME DOOR
<br />HOLDER
<br />48" MAX (ADA)
<br />48" MAX (NFPA, ADA)
<br />42" MIN (NFPA)
<br />MEASUREMENTS
<br />TO TOP OF
<br />(1 219mm)
<br />(1219mm MAX)
<br />(1067mm MIN)
<br />SHOWN ARE
<br />PULL HANDLE
<br />WALL MOUNTED
<br />SMOKE/HEAT
<br />DETECTOR
<br />USE ONLY UL LISTED FIRE ALARM SIGNALING LINE (ADDRESSABLE) CIRCUITS SHIELDING EXAMPLE
<br />TWISTED SHIELDED PAIR CABLE UL LISTED FIRE PROTECTIVE SIGNALING CABLES MAY BE SELECTED FROM THE SIMPLEXGRINNELL WIRE & CABLE TABLE, #WIRE TABLE
<br />(TSP) FOR IDNETS, DATA COMM.
<br />LINES AUDIO, PHONE & SPEAKER
<br />IN
<br />MIRI�NG IN A FIRE ALARM SYSTEM.
<br />SIZE IS 18-2 AWG SOLID STP. PRODUCT INFORMATION
<br />---CUT EXAMPLE: WIRING TECHNIQUES FOR SHIELDED CABLE:
<br />#18-2 AWG SHIELDED - SHIELDS AND DRAINS MUST NEVER TOUCH GROUND.
<br />TWISTED -PAIR CABLE - MOST GROUNDS ARE DUE TO SHIELDING ISSUES.
<br />- MOST SHORTS ARE SHIELD TO CONDUCTOR.
<br />TRIM AWAY ONLY - BY CREATING A PROPER PROCEDURE FOR WIRE
<br />THE SHIELD AND HANDLING WITH ADDRESSABLE CIRCUITS
<br />KEEP THE DRAIN n MOST GROUNDS AND SHORTS CAN BE ELIMINATED.
<br />WIRE UNDAMAGED. - ALL UNSHIELDED WIRE MUST BE ENTIRELY IN GROUND CONDUIT.
<br />- CONDUIT SYSTEM MUST HAVE A GOOD REFERENCE TO EARTH GROUND
<br />SHIELD - PIGTAILS, (T-TAP) WIRING IS PERMITTED TO ADDRESSABLE DEVICES
<br />FOR CLASS B CIRCUIT WIRING.
<br />'_*`
<br />PREPARE THE CABLE BY DRAIN WIRE EXAMPLE FOR
<br />REMOVING 2" TO 4" OF WIRING LABELING
<br />JACKET AS NEEDED, 0)
<br />WIRE
<br />REUSE INSULATION—� DISCARD TAG
<br />GENERAL WIRING GUIDELINES SHIELD
<br />1. ALL WIRING IS TO BE COPPER CONDUCTOR. ALL EQUIPMENT MUST
<br />BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURERS
<br />RECOMMENDATIONS AND THE SPECIFICATIONS AND STANDARDS
<br />OF THE AUTHORITY HAVING JURISDICTION. THE INSTALLATION OF DRAIN WIRE TO PREVENT CONFUSION AND POSSIBLE
<br />__�_S'IEL
<br />JST REUSE
<br />DRAII
<br />ALL WIRING, CABLE AND EQUIPMENT MUST BE IN ACCORDANCE ERRORS, ALL WIRES MUST BE TAGGED.
<br />WITH NFPA 70, NATIONAL ELECTRICAL CODE NEC), AND SPECIFICALLY SEE WIRE LEGEND FOR TYPES.
<br />'ALLY
<br />WITH ARTICLE 760, FIRE ALARM PROTECTIVE SIGNALING SYSTEMS;
<br />ARTICLE 800, COMMUNICATION CIRCUITS, WHERE APPLICABLE.
<br />2. IF SHIELDED WIRE IS USED, THE FOLLOWING MUST BE OBSERVED: DRAIN WIRE
<br />A. METALLIC CONTINUITY OF THE SHIELD MUST BE MAINTAINED AND
<br />INSULATED THROUGHOUT THE ENTIRE LENGTH OF THE CABLE. STRIP OFF APPROX. RED
<br />B. SHIELDS SHALL ONLY BE CONNECTED AT THE CONTROL UNIT. 1-2 INCHES OF PUSH REUSED INSULATION
<br />SHIELD MUST NOT BE CONNECTED TO, OR TOUCH CONDUIT, ELECTRICAL BLACK INSULATION TO CAREFULLY DOWN INTO
<br />BOXES, OR ASSOCIATED HARDWARE AT ANY POINT. SLIDE ONTO DRAIN WIRE. JACKET. SECURE WITH
<br />C. THE ENTIRE LENGTH OF THE CABLE MUST HAVE A RESISTANCE GREATER ELECTRICAL TAPE.
<br />THAN 1 MEGOHM TO EARTH.
<br />D. ALL CONDUCTORS ARE TO BE FREE OF SHORTS AND GROUNDS.
<br />3. UNDERGROUND WIRING MUST BE LISTED FOR APPLICATION AND FREE OF ALL WATER. B�CK
<br />4. WIRING OTHER THAN THAT CONNECTED TO ELEVATOR CABS MUST NOT BE RUN
<br />IN ELEVATOR SHAFTS (REF.NFPA 70, ARTICLE 620). REDUCE EXPOSED WIRES TO
<br />5. WIRING IN DUCTS PLENUMS AND OTHER AIR HANDLING SPACES MUST BE LISTED ABOUT 5/16" TO 3/8" FOR
<br />FOR PLENUM US� AND INSTALLED IN ACCORDANCE WITH NFPA 70, ARTICLE 300. INSERTION INTO BOX -TYPE
<br />6. SPLICING IS PERMITTED IN ACCORDANCE WITH NFPA 70. ALL JUNCTIONS MUST OR SCREW -CLAMP TERMINALS.
<br />BE INSULATED AS SOUNDLY AS THE ORIGINAL JACKET. CONTINUITY OF ANY SHIELD
<br />(WHERE USED) MUST BE MAINTAINED.
<br />7. ONLY SYSTEM WIRING CAN BE RUN IN THE SAME CONDUIT.
<br />8. THE COMMUNICATION CIRCUIT MEETS THE OPERATIONAL CHARACTERISTICS DEFINED FOR A STYLE 4
<br />AND STYLE 6 SIGNALING LINE CIRCUIT. MAXIMUM WIRE RUN NOT TO EXCEED 2500 FT.
<br />9. ALL CIRCUITS ARE SUPERVISED AND POWER -LIMITED UNLESS OTHERWISE INDICATED. SHIELD WIRES ARE NOT SUPERVISED.
<br />10. OPERATING POWER, FOR IDNet DEVICES, MUST ORIGINATE FROM A POWER -LIMITED POWER SUPPLY LISTED FOR FIRE
<br />PROTECTIVE SIGNALING USE OR, FROM THE F.A. CONTROL PANEL POWER SUPPLIES INDICATED IN THE APPROPRIATE
<br />DIAGRAM. MAXIMUM WIRE NOT TO EXCEED 1KM (3270 FT).
<br />11. WHEN COMMUNICATION WIRING OR OPERATING WIRING LEAVES THE BUILDING, OVERVOLTAGE PROTECTORS ARE
<br />REQUIRED; USE 2081-9044, INSTALL ONE WHERE IT LEAVES THE BUILDING AND ONE WHERE IT ENTERS THE NEXT BUILDING.
<br />12. TO PREVENT CONFUSION AND POSSIBLE ERRORS, TAG ALL CONDUCTORS, CODE AT INSTALLATION, TO IDENTIFY
<br />CIRCUIT ASSIGNMENT, POLARITY AND IN OR OUT DIRECTION OF THE WIRING. LOG ON AS-BUILTS.
<br />13. LEAVE ADEQUATE SLACK IN THE WIRING TO ALLOW FOR TROUBLE SHOOTING,
<br />SIMPLEXGRINNELL IS NOT RESPONSIBLE FOR ELECTRICAL CONTRACTOR'S WIRE CONDITIONS.
<br />14. IDNet COMMUNICATION LINE SPECS.:
<br />MAX. 36 VDC @ .5A 15. IDNET MAXIMUM NUMBER OF DEVICES:
<br />3333 BAUD NON -CODED 250
<br />33Q MAX. LINE RESISTANCE CODED PIEZO BASES 43 MAX.
<br />217 ADDRESSES STILL AVAILABLE FOR OTHER DEVICES.
<br />INSTRUCTIONS
<br />1. REMOVE ELECTRONIC CARD CAGE (IF PRESENT)
<br />AND STORE IT IN A SAFE DRY AREA.
<br />2. NO KNOCKOUTS PROVIDED. CUT CONDUIT/SERVICE ENTRANCE
<br />OPENINGS. REFER TO FIG.1 FOR PROPER LOCATIONS.
<br />CONDUIT PROTRUSION INTO BOX 1/2" MAX.
<br />3. MOUNT BOX TO WALL: BOX MUST BE LEVEL AND PLUMB.
<br />FOR SURFACE MOUNT USE TEAR DROP AND CLEARANCE HOLES
<br />ON BACK SURFACE.
<br />FOR SEMI -FLUSH MOUNT: USE WALL STUD GUIDES FOR MAXIMUM
<br />ALLOWABLE BOX DEPTH TO PROVIDE OPEN DOOR CLEARANCE.
<br />USE KNOCKOUTS ON SIDE WALL, SCREW OR NAIL BOX TO WALL STUDS.
<br />4. MINIMUM DISTANCE BETWEEN ANY TWO BOXES IS 3 1/4" (6" MAXIMUM).
<br />5. IF PRESENT, USE WIRE MANAGEMENT BRACKETS ON BOX SIDES
<br />TO SECURE WIRE RUNS.
<br />6. NEMA RATING: NEMA 1 - GENERAL PURPOSE.
<br />7. DO NOT LOCATE POWER -LIMITED WIRING IN THE SHADED AREAS
<br />OF THE BACKBOX, THIS AREA IS RESERVED FOR NON -POWER
<br />LIMITED CIRCUITRY SUCH AS AC POWER, BATTERIES AND CITY
<br />CONNECTION.
<br />8. REFER TO SIMPLEX BACKBOX INSTALLATION DOCUMENT
<br />579-117 FOR DETAILED INSTRUCTIONS.
<br />--DRAIN WIRE
<br />FRICAL TAPE.
<br />4100ES BACKBOX INSTALLATION
<br />—11 11/16"
<br />— 6 29/32" —
<br />1 7/16" — —
<br />4 3/4
<br />KNOCKOUT
<br />—1
<br />SCREW/NAIL--]Fl
<br />HOLES FOR
<br />SEMI -FLUSH
<br />MOUNT
<br />(SEE NOTE 3.)
<br />WALL STUD GUIDES
<br />(SEE NOTE 3.)
<br />NOTE: ADA REQUIREMENTS LIMIT THE ALLOWABLE PROTRUSION OF OBJECTS
<br />MOUNTED IN PUBLIC ACCESSIBLE WALKS, HALLS, CORRIDORS,
<br />PASSAGEWAYS OR AISLES. THE 4 INCH (100mm) RESTRICTION
<br />APPLIES TO ANY ITEM IN WHICH THE MEASUREMENT FROM THE
<br />FLOOR TO THE BOTTOM OF THE UNIT IS MORE THAN 27 INCHES.
<br />IYPICAL CONDUII LUCAIION I -OR
<br />PWR. LIMITED FIELD WIRING
<br />- - -
<br />Fo—c'D
<br />FIG
<br />PKG. SIZE
<br />PID NUMBER
<br />BOX HEIGHT
<br />1 BAY
<br />2975-9407
<br />22"
<br />2 BAY
<br />2975-9408
<br />40"
<br />3 BAY
<br />2975-9409
<br />56"
<br />I BAY
<br />2975-9410
<br />22"
<br />2 BAY
<br />2975-9411
<br />40"
<br />3 BAY
<br />2975-9412
<br />56"
<br />1 BAY
<br />2975-9438
<br />22
<br />2 BAY
<br />2975-9439
<br />40"
<br />3 BAY
<br />2975-9440
<br />56"
<br />66"
<br />(TYPICAL, FOR
<br />5 FOOT HEIGHT
<br />TO LCD DISPLAY
<br />CENTERLINE)
<br />CHART
<br />5 17/32"
<br />WALL
<br />FLOOR
<br />FINISHED
<br />WALL
<br />SIDE WALL
<br />CLASS 'A'
<br />+ +
<br />CLASS 'B'
<br />+ + - -
<br />WIRES MUST BE CONNECTED
<br />SEPARATELY UNDER TERMINALS.
<br />A CONTINUOUS WIRE LOOP
<br />IS NOT ALLOWED.
<br />ONLY CLASS B IDNET, MAPNET OR
<br />DATA COMM. CABLE MAY BE
<br />T-TAPPED. IT MUST BE DONE
<br />IN A JUNCTION BOX WITH
<br />CABLE STRAIN RELIEF I.E..
<br />CORD CLAMP/BUSHING AND
<br />TAPE WRAPPED AS SH�WN HERE
<br />STRIP THE INSULATED WIRES
<br />ABOUT 5/16" TO 3/8" FOR
<br />INSERTION INTO BOX -TYPE OR
<br />SCREW -CLAMP TERMINALS ON
<br />THE ADDRIESSABLE DEVICE.
<br />_---THE SHIELD/DRAIN IS NEVER
<br />CONNECTED TO THE DEVICE.
<br />lb
<br />TRIM THE BARE DRAIN
<br />TO ABOUT 1-1/2". JOIN
<br />THEM WITH AN ELECTRICAL
<br />CONNECTOR LISTED AND
<br />APPROVED FOR WIRE SPLICING.
<br />REFER TO FIGA FOR TYP.
<br />CONDUIT PENETRATION LOCATIONS
<br />3 1/4" MIN.
<br />24" 10" MAX.
<br />F
<br />16
<br />FOR SURFACE MOUNT
<br />USE 4 HOLES TO SECURE
<br />BACKBOX TO WALL
<br />BATTERY AREA
<br />(IF APPLICABLE)
<br />NO CONDUIT ENTRY OR
<br />WIRING IN THIS AREA
<br />EXAMPLE OF
<br />ADDITIONAL CABINET
<br />MOUNTING LOCATION
<br />CONDUIT FOR INTERNAL
<br />PANEL HARNESSES OR
<br />NPL WIRING.
<br />SECURE THE
<br />DRAIN WIRES INTO
<br />THE CONNECTOR
<br />APPROVED FOR
<br />THE PURPOSE.
<br />WIRES MUST BE
<br />TIGHT ENOUGH
<br />TO HOLD SECURELY
<br />AND NOT SLIP OUT
<br />OF THE CONNECTION.
<br />ENSURE BARE DRAINS
<br />ARE SECURED AND
<br />UNABLE TO MAKE
<br />EXTERNAL CONTACT.
<br />SEE NOTE 2
<br />PID NUMBER
<br />BOX HEIGHT
<br />BOX LENGTH
<br />BOX DEPTH
<br />2081-9280
<br />12"
<br />26 1/2-
<br />12"
<br />4081-9306
<br />13 1/2"
<br />27 7/8"
<br />14 5/8"
<br />4081-9308
<br />13 1/2"
<br />27 7/8"
<br />14 5/8"
<br />DETECTOR LOCATION REQUIREMENTS FOR WALL SECTIONS
<br />NFPA 72
<br />DEPTH OF WALL
<br />SECTION ABOVE
<br />DOOR FRAME MOUNTED
<br />CEILING MOUNTED
<br />DOOR
<br />SMOKE DETECTOR LISTED FOR FRAME
<br />d
<br />MOUNTING OR AS PART OF CLOSER
<br />SMOKE DETECTOR CEILING MOUNTED
<br />ASSEMBLY
<br />A
<br />B 100-300 mm
<br />0 610 mm (0
<br />t
<br />d 610mm
<br />or
<br />- 24 in.)
<br />24 in,)
<br />�i�
<br />d
<br />max. 1.52 m (5 ft)
<br />ON BOTH SIDES
<br />d min. but not less
<br />OF DOORWAY
<br />DETECTOR OR DETECTOR CLOSER
<br />than 305 mm (12 in.)
<br />MOUNTED ON EITHER SIDE
<br />ONE DETECTOR MOUNTED ON EITHER SIDE
<br />C
<br />D 100-300 mm
<br />OVER 610 mm
<br />d2> 610mm
<br />c1l < 610mm (2 4 1 in.)
<br />d I < 61 Omm
<br />d2> 610 mm (2 4 i n.)
<br />(24 in.)
<br />(24 In.)
<br />(24 in.)
<br />ON ONE SIDE
<br />4 --1 F_[��
<br />_11
<br />ONLY
<br />DETECTOR OR DETECTOR CLOSER
<br />1.52 m (5 ft) max.
<br />MOUNTED ON HIGHER SIDE
<br />ONE DETECTOR MOUNTED
<br />ON HIGHER SIDE min. = d 2
<br />E
<br />F
<br />o r o r
<br />OVER 610 mm
<br />d > 610mm
<br />(24 in.)
<br />(24 in.)
<br />d 100-300 mm
<br />ON BOTH SIDES
<br />1.52 m (5 ft) max. 1.52 m (5 ft) max.
<br />DETECTOR OR DETECTOR CLOSER
<br />min. = d I -min. d
<br />MOUNTED ON EITHER SIDE
<br />TWO DETECTORS REQUIRED
<br />OVER 1524 mm G
<br />MIGHT REQUIRE ADDITIONAL DETECTORS
<br />(60 in.)
<br />END —OF —LINE RESISTOR CODES
<br />NOTE: REFER TO PANEL/MODULE AND DEVICE INSTALLATION
<br />INSTRUCTIONS FOR PROPER TERMINATIONS.
<br />* USE WITH RETROFIT OR HIGH CURRENT MODULE
<br />MODEL
<br />REFERENCE
<br />NUMBER
<br />OHMS
<br />1ST BAND
<br />2ND BAND
<br />3RD BAND
<br />4TH BAND
<br />5TH BAND
<br />WATTS
<br />CIRCUIT TYPE
<br />FIRE ALARM PANEL/MODULE
<br />4081-9001
<br />733-892
<br />2.2 K
<br />RED
<br />RED
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />ANNUNCIATOR (4300)
<br />4004, 4010 (TROUBLE)
<br />4081 -9002
<br />733-893
<br />3.3K
<br />ORANGE
<br />ORANGE
<br />RED
<br />GOLD
<br />N/A
<br />1
<br />N.O, INITIATING
<br />PULL, SMOKE, HEAT,
<br />WATERFLOW, TAMPER, ETC.
<br />—
<br />4004*, 4004R, 4005*, 4006,
<br />4100, 4120, 4100U, ZAM'S
<br />24 PT. 1/0 SWITCH SUPV.
<br />4605-7401, 4100 SERIES
<br />4081-9003
<br />733-896
<br />4.7 K
<br />YELLOW
<br />VIOLET
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />CURRENT LIMITED N.C. INITIATING
<br />4090-9001 IDNET IAM (EOLR)
<br />NOTIFICATION (DACT)
<br />2080-9024
<br />4081-9004
<br />733-886
<br />6.8K
<br />BLUE
<br />GREY
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />N.O. INITIATING
<br />PULL, SMOKE, HEAT,
<br />WATERFLOW, TAMPER, ETC.
<br />4004, 4005,
<br />4090-9001 IDNET AM
<br />2190-9173 MAPNETII 2 PT 1/0
<br />4-20MA ZAM (TROUBLE)
<br />4081 -9005
<br />733-984
<br />1.8K
<br />BROWN
<br />GREY
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />CURRENT LIMITED N.C. INITIATING
<br />(IN LINE)
<br />4090-9001 IDNET IAM
<br />4081 -9006
<br />733-890
<br />560 n
<br />GREEN
<br />BLUE
<br />BROWN
<br />GOLD
<br />N/A
<br />1
<br />N.C. INITIATING (EOLR)
<br />4005*, 4090-9001 IDNET IAM
<br />4100, 41 OOU
<br />4081-9007
<br />733-891
<br />1.2K
<br />BROWN
<br />RED
<br />RED
<br />GOLD
<br />N/A
<br />1
<br />N.C. INITIATING (EOLR)
<br />4005
<br />4081-9008
<br />733-894
<br />10K
<br />BROWN
<br />BLACK
<br />ORANGE
<br />GOLD
<br />N/A
<br />1/2
<br />NOTIFICATION
<br />4004, 4005, 4006, 4008,
<br />4009, 4010, 4100, 410OU
<br />4081 -9009
<br />733-912
<br />20n
<br />RED
<br />BLACK
<br />BLACK
<br />GOLD
<br />N/A
<br />1
<br />TO MR-101 RELAY COIL
<br />4005 8 POINT 1/0
<br />4081-9010
<br />733-973
<br />1K
<br />BROWN
<br />BLACK
<br />RED
<br />GOLD
<br />N/A
<br />1
<br />N. C. INITIATING (ACROSS CONTACTS)
<br />4005*, 4090-9001 IDNET IAM
<br />24 PT. 1/0 (ACROSS CONTACTS)
<br />4605-7401, 4100 SERIES
<br />CURRENT LIMITED N.C. INITIATING
<br />(IN SERIES WITH CONTACT)
<br />4090-9001 IDNET IAM
<br />4081-9011
<br />733-974
<br />100n
<br />BROWN
<br />BLACK
<br />BROWN
<br />GOLD
<br />N/A
<br />112
<br />ANNUNCIATOR (N2)
<br />4006, 4008, 4010
<br />4081-9012
<br />733-985
<br />22K
<br />RED
<br />RED
<br />ORANGE
<br />GOLD
<br />N/A
<br />1/2
<br />SPEAKER CIRCUIT
<br />4003
<br />4081-9013
<br />734-086
<br />4.99K
<br />YELLOW
<br />WHITE
<br />WH ITE
<br />BROWN
<br />BROWN
<br />1/2
<br />4081-9014
<br />734-092
<br />2.4K
<br />RED
<br />YELLOW
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />N.C. INITIATING
<br />(SECURITY MONITORING EOLR)
<br />4090-9001 IDNET IAM
<br />4081-9015
<br />734-093
<br />1.5K
<br />BROWN
<br />GREEN
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />CURRENT LIMITED N.C. INITIATING
<br />(SECURITY MONITORING EOILR)
<br />4090-9001 IDNET IAM
<br />4081-9016
<br />734-149
<br />150K
<br />BROWN
<br />GREEN
<br />YELLOW
<br />GOLD
<br />N/A
<br />1/2
<br />4081-9017
<br />734-171
<br />3.9 K
<br />ORANGE
<br />WHITE
<br />RED
<br />GOLD
<br />N/A
<br />1
<br />4081-9018
<br />734-168
<br />10K
<br />BROWN
<br />BLACK
<br />ORANGE
<br />GOLD
<br />N/A
<br />1
<br />70VRMS CONSTANT SUPV. NACS
<br />4100-1260
<br />378-090
<br />8.2K
<br />G RAY
<br />RED
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />SECURITY MONITORING (EOLR)
<br />4100, 41 OOU
<br />378-046
<br />5.6K
<br />GREEN
<br />BLUE
<br />RED
<br />GOLD
<br />N/A
<br />1/2
<br />N.O, SECURITY MON. (SERIES)
<br />4100, 41 OOU
<br />378-069
<br />12K
<br />BROWN
<br />RED
<br />ORANGE
<br />GOLD
<br />N/A
<br />1/2
<br />N.C. SECURITY MON, (SHUNT)
<br />4100, 410OU
<br />4009 NAC PANEL, TYPICAL WIRING DETAIL
<br />IF OPTIONAL SHIELDS ARE USED FOR IDNet WIRING,
<br />FOLLOW THESE PRECAUTIONS. 4-M FROM PREV10US IDNet DEVICES
<br />1. IF IDNet WIRING CONTINUES ON TO ANOTHER DEVICE, UK Ne A
<br />TAPE SHIELDS TOGETHER. DO NOT TERMINATE SHIELD AT
<br />4009 IDNet. �M TO ADDITIONAL IDNet DEVICES
<br />2. IF IDNet WIRING TERMINATES AT THE 4009, TAPE SHIELD. UK RETURN TO HOST IDNet CONTROL PANEL
<br />DO NOT TERMINATE SHIELD AT 4009 IDNet.
<br />IDNet CONTROLLER ADDRESS:
<br />TO NAC#:Vl DEVICES 0� V
<br />@
<br />MIN
<br />0%
<br />0
<br />tjtj11++
<br />0 0 ==
<br />+_+_ E IDNET
<br />NAC 1 NAC 2 NAC 3 NAC 4
<br />FSW2
<br />11 1 a. 10
<br />Ll H 1111 1,04"
<br />AAUX POWER
<br />POS IN Doo "P.,
<br />PO Uff WRDMRE
<br />To INPUT 0
<br />RE IN 0
<br />R 0
<br />PEr OUT MSIBE
<br />OS IN � 0 . 00co a
<br />POS OUT WRDNIRE
<br />RET IN INPUT 2
<br />REr OUT AUDIBLE BATTERY
<br />4009-9201 IDNet NAC EXTENDER 0
<br />ADDIRM-RE NAC SYSTW 0
<br />@
<br />BATTERY
<br />BATTERY
<br />CONNECT A 12 AWG COPPER GROUND WIRE FROM SAFETY
<br />GROUND IN THE ELECTRICAL DISTRIBUTION PANEL TO
<br />THE 4009 SAFETY GROUND STUD.
<br />GROUND
<br />NEUTRAL CONNECT TO 120VAC 60HZ INPUT 3A MAX.
<br />r HOT 120V 4
<br />_[TIIH.I�NAL
<br />PART OF
<br />r(
<br />-991
<br />733
<br />0071
<br />Go 00
<br />;� P_
<br />C?
<br />CID T::
<br />CN
<br />C9 9"
<br />M co
<br />w co
<br />U,
<br />[-- L�j
<br />CN
<br />%
<br />%
<br />z
<br />1.- 0
<br />7%
<br />cn
<br />Uj
<br />LU oo
<br />3
<br />c:, R,
<br />C4
<br />CO zi; 19
<br />=
<br />C4
<br />wmm
<br />LUco-
<br />�: co
<br />—1
<br />z U- 6i
<br />=);�tg
<br />4�_
<br />c) >
<br />12
<br />C3
<br />LU
<br />co
<br />Mn
<br />0
<br />U)
<br />>
<br />0
<br />LU >.
<br />Of
<br />0
<br />Uj
<br />F.
<br />0
<br /><
<br />06
<br />U-)
<br />27. cy)
<br />0 U) C) <
<br />0
<br />_j
<br />0
<br />LJJ _j
<br />--1 Lj_
<br />< F- -n -
<br />cp 0 CD
<br />0 0 ca _j
<br />= _j _j
<br />X —
<br />Uj of <
<br /><
<br />cq >-
<br />0 FE M
<br />LO
<br />M 0 0-
<br />i C) LU
<br />Uj LL_ r-_ P�_j
<br />0
<br />0
<br />0
<br />cn
<br />LU
<br />M
<br />0
<br />—
<br />Uj
<br />0
<br />LU
<br />M
<br />co
<br />Ln_j F_
<br />DRAWN BY: B. KNICKLE
<br />CHECKED BY: F. REINHART
<br />ISSUE DATE: 7/19/16
<br />CURTIS ENGINEERING SERVICE, LLC - CA#31561 JOB #: 292415807
<br />JAMES M. CURTIS, P.E. - PE#37912
<br />29775 BAYHEAD ROAD PROJECT#: 1292:993523001
<br />DADE CITY, FLORIDA 33523
<br />SIMPLEXGRINNELL @ 2016
<br />DEL EGA TED ENGINEER OF RECORD SYSTEM:
<br />Digitally signed C& Z/
<br />0�
<br />N 14F.-sargoo-'k
<br />is ! Z S 'r . %,
<br />by James Curt -%'- -S , -
<br />No.
<br />Date:
<br />OF
<br />2016.0722
<br />NA%.
<br />'09:32:29 -04 00
<br />11111%%
<br />LARM SYSTEM
<br />SHEET:
<br />WIRING TYPICALS
<br />FA-701
<br />
|