4766 Gall Blvd (2) - Laserfiche WebLink

Browse Search

F 6 5 4 3 2 Motion Detector Installation and Wiring Ceiling mount motion detectors are used to detect motion in the store after business hours. Stock lights will be energized when motion is detected. (2) Detectors are supplied with the CPC equipment... one for the front of the store and one for the stock room. NORTH GENERAL NOTES A. REFER TO E1 FOR GENERAL CONTRACTOR' RESPONSIBILITIES, E.C. MAY USE CABLE TRAY FOR LOW VOLTAGE CABLES, SEE 2/E2. B. RUN CONDUIT FROM SENSORS TO BOTTOM OF STRUCTURE. C. REFRIGERATION UNITS TO BE CONNECTED TO EMS PANEL BY DOLLAR GENERAL REFRIGERATION CONTRACTOR. SENSOR PLAN KEYED NOTES ALWAYS INSTALL THERMOSTATS 8'-0" A.F.F. THE EXACT MOUNTING LOCATION OF THE THERMOSTAT "TS" MAY VARY DEPENDING ON THE STORE LAYOUT AND DUCT CONFIGURATION. REFER TO SITE SPECIFIC MECHANICAL DRAWINGS FOR HVAC ZONED THERMOSTAT MOUNTING LOCATIONS. IF THERMOSTATS ARE MOUNTED ON EXTERIOR WALLS DUE TO DUCT CONFIGURATION, THEY ARE THEN TO BE INSULATED TO PREVENT AIR INFILTRATION. IF ADDITIONAL HVAC UNITS ARE USED, ADD ADDITIONAL THERMOSTATS "TS". PHONE LINE #1 - TWO RJ-11 PORTS. ONE (1) LOCATED IN OFFICE W/RJ-45 DATA JACK COMBO AND ONE (1) AT REGISTER. 24 GA. CAT 5, 4-PAIR TWISTED WIRE ONLY. USE BLUE AND BLUE & WHITE [2] WIRES. HOOK TO LINE #1 TERMINAL IN RJ-11 JACK EACH PHONE JACK TO HAVE DEDICATED, SEPARATE HOME RUN TO DMARC. LABEL AS "PHONE" AT THE DESTINATION AND AT DMARC. PHONE COMPANY PROVIDES FINAL HOOK UP TO DMARC ONLY.PHONE LINE #2 - RJ-11 PHONE JACK SUPPLIED AND WIRED BY CONTRACTOR, EMS/LOW VOLTAGE - FLOOR PLAN LABEL ANNUNCIATOR "ROOFTOP UNIT DUCT SMOKE DETECTOR" 'HORNtR LARM TATUS L------� REMOTE AUDIO/ VISUAL ALARM ANNUNCIATOR LOCATED IN RECEIVING AREA. Scale: 1/8" = 1'-0" DUCT SMOKE DETECTOR LOCATED AT ROOFTOP AIR HANDLING UNIT F— — — — — — — — — — -- (9ROOFTOP UNIT I SHUTDOWN WIRED BY MECH. CONTR. I ALARM SIGNAL (+) I� COMMON(-) AUX POWER (+) I I TROUBLE L — — — — — — — — — J DUCT DETECTOR ALARM WIRING Scale: NTS • Motion detectors require a four conductor cable: o (2) wires for 24AC Power — (Red to Red and Black to Black) o (1) for Control Signal Normally Open Contact (Yellow to Green) o (1) for Control Common (Orange to White) ***Do not use the green wire from Motion Detector*** • Pull a 4 conductor cable from the motion detectors to the CPC panel and terminate at the terminal strip according to the wiring legend. The Yellow and Orange wires for each sensor shall be pulled to the CPC input board to the points labeled Motion Sensor Front and Motion Sensor Rear. Polarity does not matter since the motion detector simply feeds the control board a "dry set of contacts (an Open or Closed signal). For simplicity, we recommend connecting the Yellow motion detector wire to the Green of the four conductor home run back to the panel ... and the Orange to the White of the four conductor. The Red and Black wires shall be pulled to the terminal strip located just above the breaker. This terminal strip provides 24VAC for the sensors. Example of location for "Front Entrance" Motion Detector ***Set Dip Switches (2) and (3) in the UP or "ON" Position. This sets the motion detector for a 20 minute lights activation period anytime motion is detected*** To test the sensors once installed, cover the sensors with duct tape (or something similar). Go to the E2 controller. The status of the motion detectors can be viewed on the "Home" screen. If you are not sure if you are on the "Home" screen, simply press the button with the house on it. The bottom center of the screen has a section called Sensor Control ... the motion detectors are defined as Motion Front and Motion Rear. With the motion sensor coved in tape the E2 should read "OFF' for the appropriate sensor. This indicates that no motion is detected. By removing the tape, the detector should sense motion and the E2 should read "ON". For quickness in testing the sensors, I recommend setting dip switches 1, 2, and 3 in the up or "ON" position. This sets the motion detector for a 30 second delay. This means that the sensor will wait 30 seconds before it sends the E2 a change of state between motion and no motion. (Be patient). Power to the motion detector must then be reset (this allows the motion detector to accept the new dip switch settings.) ***Important***When you are complete with the test you must set the dip switches in the correct position for normal operation ... (2, and 3 in the up or "ON" position for a 20 minute delay). Power to the motion detector must then be reset (this allows the motion detector to accept the new dip switch settings. Failure to move dip switches to correct position will cause the Stock Lights to short cycle. DEVICE SCHEDULE SYMB DESCRIPTION CABLE TYPE SUPPLIER INSTALLER NOTES OT OUTDOOR AIR TEMP (501-1122) BELDEN 8761 OR EQUIVALENT EMS SUPPLIER GENERAL (1) PER RECEIVING ENTRY (22AWG, 2C, STRANDED, SHIELDED) CONTRACTOR MOUNTED 8'-0" A.F.F. ST SUPPLY TEMP (201-0041) BELDEN 8761 OR EQUIVALENT EMS SUPPLIER GENERAL (1) PER HVAC UNIT IN SUPPLY DUCT (22AWG, 2C, STRANDED, SHIELDED) CONTRACTOR TS TOUCHSCREEN THERMOSTAT (810-1600) 8C T-STAT CABLE EMS SUPPLIER GENERAL (1) PER HVAC UNIT ZONE CONTRACTOR 8'-0" A.F.F. O RJ-11/RJ-45 DATA JACK CAT-5 DATA CABLE GENERAL GENERAL (1) AT OFFICE COMPUTER CART PHONE COMBO (24AWG, 4 TWISTED PAIR) CONTRACTOR CONTRACTOR m MOTION SENSOR SWITCH LEVITON EZ-FIND ODS-10-IDW GENERAL GENERAL (1) PER RESTROOM CONTRACTOR CONTRACTOR CONSULTANT. - SEAL SEAN PATRICK PIC-KELL, PE 83946 THIS DRAWING SHALL NOT BE USED FOR CONSTRUCTION PURPOSES UNTIL THE SEAL AND SIGNATURE OF THE RESPONSIBLE REGISTRANT APPEARS ON THE DRAWING, AND PROPER PERMIT FORMS AND RELATED FEES ARE TRANSMITTED BY THE OWNER, OWNER'S AGENT OR CONTRACTOR TO THE AUTHORITY HAVING JURISDICTION. DATE ISSUED FOR REV 03/29/2021 PEMB COORDINATION 05/20/2021 CIVIL SUBMISSION 05/20/2021 DUKE COORDINATION 06/07/2021 PEMB COORDINATION 02 08/09/2021 CIVIL RESUBMISSION 1 08/25/2021 OWNER REVIEW 1 1 /08/2021 REVISED ELEVATIONS 1 1 /29/2021 PERMIT SUBMITTAL Project Manager Drawn L. LONG N. NG UYEN Project Leader Checked L. LONG M. GOOD Date Dept Mgr Approval 02/23/2021 M. GOOD Client PALMETTO ZEPHYRHILLS - GALL BLVD., LLC P.O. Box 1615, Thomasville, GA 31 799 Office: (229) 226-1 177 Contact: Daniel Tubb Project DOLLAR GENERAL Corner of Gall Boulevard and C Avenue, Zephyrhills, FL 33542 (City of Zephyrhills) Store #: 23227 Drawing Title EMS/LOW VOLTAGE PLAN DO NOT SCALE DRAWING Project No. Drawing No. JCDT.20.0451 EMS1