4766 Gall Blvd (2) - Laserfiche WebLink

Browse Search

MANUAL PULL STA' CEILING MOUNTED SMOKE DETECTOR DUCT TYPE SMOKE DETECTOR CEILING MOUNTED COMBINATION HORN/STROBE WALL MOUNTED COMBINATION HORN/STROBE TAMPER SWITCH F FLOW SWITCH SD TS F CEILING TYPE STROBE -CEILING MOUNTED SMOKE DETECTOR LOCATED ABOVE THE FACP E FOR NOTE: ONITORING FIRE ALARM SYSTEM SHALL COMPLY WITH FLORIDA BUILDING CODE (201 7) k-8 AND NFPA 72, 2013 EDITION BLE FIRE ALARM CONTROL PANEL WITH BUILT-IN INTERNAL SURGE PROTECTION DEVICES TO PROTECT BOTH POWER AND DATA LINES TO ISOLATE THE FIRE ALARM CONTROL PANEL. FIRE ALARM RISER DIAGRAM Scale: NTS SYMBOL FIRE ALARM SYSTEM SYMBOL SCHEDULE DESCRIPTION FWALL MOUNTED FIRE ALARM PULL STATION A CEILING MOUNTED FIRE ALARM STROBE A\ CEILING MOUNTED COMBINATION FIRE ALARM HORN AND STROBE C F WALL MOUNTED COMBINATION FIRE ALARM HORN AND STROBE W <FF O/WP WALL MOUNTED AND WEATHER-PROOF COMBINATION FIRE ALARM W HORN AND STROBE s DUCT MOUNTED SMOKE DETECTOR (MOUNT IN RETURN AIR DUCT) OCEILING MOUNTED SMOKE DETECTOR TS WP WEATHER-PROOF FIRE RISER TAMPER SWITCH WF WP WEATHER-PROOF FIRE RISER WATER FLOW SWITCH NOTES: 1. FIRE ALARM SYSTEM SHALL PROVIDE A GENERAL EVACUTATION SIGNAL FOR THE ENTIRE BUILDING. 2. PROVIDE WIRING PER NFPA 72. 3. ABOVE GROUND AND UNDERGROUND WIRING SHALL COMPLY WITH CHAPTER 12 IN NFPA 72. 4. TRANSIENT PROTECTION SHALL COMPLY WITH CHAPTER 12 IN NFPA 72. 5. ALL DUCT DETECTORS SHALL BE WIRED TO ACTIVATE ALARM SYSTEM AND SHUT DOWN FAN. 6. FIRE ALARM CONTRACTOR TO VERIFY THAT THE CANDELA INTENSITY OF THE STROBE LIGHTS SHOWN COMPLYS WITH TABLES 7.5.4.3.1(a) AND 7.5.4.3.1 (b) IN NFPA 72. AUDIO LEVEL SHALL COMPLY WITH NOTIFICATION IN CHAPTER 18, NFPA 72. ALL AUDIO AND VISUAL RATINGS SHALL MEET OR EXCEED NFPA REQUIREMENTS. 7. PROVIDE REMOTE POWER SUPPLIES AS REQUIRED FOR NOTIFICATION APPLIANCE CIRCUITS, NOT TO EXCEED 80% OF CAPACITY. 8. PROVIDE SMOKE DETECTOR ABOVE EACH REMOTE POWER SUPPLY PANEL. 9. IF REQUIRED, SMOKE DETECTOR LAYOUT SHALL COMPLY WITH SECTIONS 17.5 AND 17.7 IN NFPA 72. ADDITIONAL SMOKE DETECTORS SHALL BE PROVIDED TO REMOVE SMOKE STRATIFICATION. 10. PROVIDE BATTERY, CURRENT LOAD AND VOLTAGE DROP CALCULATIONS PER NFPA. 11. SEAL AROUND ALL PIPES & CONDUITS IN MASONRY AND DRYWALL WALLS. 12. EXTERIOR DEVICES SHALL BE SUBJECT TO ENVIROMENTAL FACTORS INCLUDING BUT NOT LIMITED TO: HUMIDITY, TEMPERATURE AND CORROSIVE ATMOSPHERES (INCLUDING COASTAL SALT AIR). 13. ALL FIRE ALARM WIRING SHALL BE MINIMUM # 14 AWG AND IN CONDUIT MIN 3/4" IN EXPOSED CEILING AREAS, PLENUM RATED CABLE IS ACCEPTABLE ABOVE LAY -IN CEILINGS IN J-HOOKS. 14. FIRE ALARM CONTRACTOR SHALL BE RESPONSIBLE FOR ALL CHARGES INVOLVED IN OBTAINING APPROVAL AND CERTIFICATION FROM STATE ELECTRICAL INSPECTOR FOR A COMPLETE SYSTEM. CERTIFIED CONTRACTOR TO PAY ALL FEES REQUIRED. 1 5. THE RISER DIAGRAM IS FOR REFERENCE PURPOSES. EXACT QUANTITIES OF DEVICES AND LOCATIONS SHALL COMPLY WITH NFPA GUIDELINES AND MEET APPROVAL OF THE STATE ELECTRICAL INSPECTOR. FIRE ALARM CONTRACTOR SHALL HAVE SHOP DRAWINGS APPROVED BY THE STATE ELECTRICAL INSPECTOR PRIOR TO COMMENCEMENT OF WORK. 16. SYSTEM TESTING SHALL COMPLY WITH NFPA 72. 17. SYSTEM OPERATION AND MAINTENANCE PROCEDURES, MANUALS, SYSTEM DOCUMENTATION AND INSTRUCTION OF OWNER'S OPERATING PERSONAL SHALL BE PROVIDED PER NFPA 72. 18. CONTRACTOR SHALL COORDINATE LOCATION OF FIRE ALARM DEVICES WITH THE LATEST DOLLAR GENERAL FIXTURE PLAN. 19. THE NEW FIRE ALARM SYSTEM SHALL BE INSPECTED AND TESTED IN ACCORDANCE WITH THEREQUIREMENTS OF NFPA 72, CHAPTER 14, "INSPECTION TESTING AND MAINTENANCE." [72:14.4.1 .1 ]. VERIFICATION OF COMPLIANT INSTALLATIONSHALL BE PERFORMED ACCORDING TO TESTING REQUIREMENTS AND PROCEDURES SPECIFIED IN 72:14.4.1 "INITIAL ACCEPTANCE TESTING." A RECORD OF ALL INSPECTIONS, TESTING AND MAINTENANCESHALL BE PROVIDED THAT INCLUDES THE FOLLOWING INFORMATION (72:14.6.2.4 (1) THROUGH (19)) REGARDING TESTSAND ALL APPLICABLE INFORMATION REQUESTED IN 72:F.14.6.2.4. [72:14.6.2.4*]. ALL INTEGRATED SYSTEMS SHALL BE TESTED, [4:1.1 .1 *]. 20. AFTER SUCCESSFUL COMPLETION OF ACCEPTANCE TESTS APPROVED BY THE AHJ, THE REQUIREMENTS OF 72:14.6.1.1 THROUGH 72:14.6.1.3 SHALL COMPLY. [72:14.6.1 J. A) A SET OF REPRODUCIBLE AS -BUILT INSTALLATION DRAWINGS, OPERATION AND MAINTENANCE MANUALS AND A WRITTEN SEQUENCE OF OPERATION SHALL BE PROVIDED TO THE BUILDING OWNER OR THEIR DESIGNATED REPRESENTATIVE. [72:14.6.1.1 ]. B) FOR SOFTWARE BASED SYSTEMS, A COPY OF THE SITE -SPECIFIC SOFTWARE SHALL BE PROVIDED TO THESYSTEM OWNER OR OWNER'S DESIGNATED REPRESENTATIVE. [72:14.6.1.2.11. C) THE COPY OF THE SITE -SPECIFIC SOFTWARE SHALL BE STORED ON SITE IN A NON-VOLATILE, NON-ERASEABLE AND NON-REWRITABLE MEMORY. [72:14.6.1 .2.2]. D) THE SYSTEM OWNER SHALL BE RESPONSIBLE FOR MAINTAINING THESE RECORDS FOR THE LIFE OF THE SYSTEM FOR EXAMINATION BY ANY AHJ. PAPER OR ELECTRONIC MEDIA SHALL BE PERMITTED. [72:14.6.1 .31. 21. THE FIRE ALARM CONTRACTOR SHALL VERIFY THAT THE RADIO STRENGTH DETERMINED BY THE FIRE MARSHAL IS ADEQUATE FOR FIRE GROUND / DEPARTMENT COMMUNICATIONS. If THE SIGNAL STRENGTH IS NOT ACCEPTABLE AN ENHANCEMENT SYSTEM SHALL BE INSTALLED. 2. FIKt ALARM Ut5)KjNtK QUALIFIC,A I IUN5: NICt I LtVtL III UK IV (3 UK 4) CLK I IFILU FIKL ALARM TECHNICIAN OR REGISTERED FIRE PROTECTION ENGINEER, EMPLOYED BY THE FIRE ALARM CONTROL PANELMANUFACTURER, CONTRACTOR, OR INSTALLER, WITH EXPERIENCE DESIGNING FIRE ALARM SYSTMS IN THE JURISDICTIONAL AREA OF THE AUTHORITIES HAVING JURISDICTION. FIRE ALARM SEQUENCE OF OPERATION THE ACTIVATION OF ANY FIRE ALARM AUTOMATIC DETECTOR CIRCUIT SHALL AUTOMATICALLY PERFORM THE FOLLOWING FUNCTIONS: 1. SEND A SIGNAL TO THE FIRE ALARM COMPANY WHICH CALLS THE FIRE DEPARTMENT AND THE CUSTOMER PROVIDED CALL LIST. 2. LIGHT THE FIRE ALARM CONTROL PANEL'S RED LED AND AUDIBLE SONALERT AND DISPLAY A DESCRIPTION OF THE DEVICE CAUSING THE ALARM. 3. ALL AUDIBLE ALARM SIGNALS SHALL SOUND UNTIL SILENCED BY THE ALARM SILENCE BUTTON. IF ALARM SIGNALS ARE SILENCED FOR ANY REASON THEY SHALL AUTOMATICALLY RESOUND IF ANOTHER ZONE ACTIVATES. 4. ALL SIGNALS SHALL FLASH UNTIL STOPPED BY THE SILENCE BUTTON. IF VISUAL SIGNALS ARE STOPPED FOR ANY REASON THEY SHALL AUTOMATICALLY RESOUND IF ANOTHER ZONE ACTIVATES. 5. POWER FAILURE, OPEN CIRCUIT OR OTHER ABNORMAL CONDITIONS IN THE FIRE ALARM CIRCUITS SHALL CAUSE THE TROUBLE SIGNAL TO SOUND AND TH AMBER ZONE TROUBLE LIGHT TO GLOW ON THE FIRE ALARM CONTROL PANEL, INDICATING WHICH CIRCUIT IS IN A DIS ARRANGED CONDITION. THE SILENCE BUTTON MAY BE SELECTED TO SILENCE THE AUDIBLE SIGNAL BUT THE TROUBLE LAMP SHALL NOT BE EXTINGUISHED UNTIL THE ABNORMAL CONDITION IS RECTIFIED. 6. IN THE EVENT OF A COMMERCIAL POWER INTERRUPTION THE SYSTEM SHALL AUTOMATICALLY TRANSFER TO AN EMERBENCY STANDBY BATTERY SOURCE. 7. DUCT SMOKE DETECTORS SHALL AUTOMATICALLY STOP THEIR RESPECTIVE FANS(S) ON DETECTING THE PRESENCE OF SMOKE. 8. SPRINKLER SYSTEM FLOW SWITCH AND TAMPER SWITCHES SHALL INDICATE AS A COMMON SUPERVISORY CONDITION AND SHALL TRANSMIT A SUPERVISORY SIGNAL TO THE FIRE ALARM PANEL. FIRE ALARM INSTALLATION REQUIREMENTS: POWER LIMITED FIRE ALARM CIRCUITS SHALL BE INSTALLED IN ACCORDANCE WITH NEC ARTICLE 760. CONDUCTORS SHALL BE EITHER SOLID OR STRANDED COPPER MINIMUM OF #14 AWG. FIRE ALARM CIRCUITS INSTALLED IN CORROSIVE, DAMP OR WET LOCATIONS MUST BE IDENTIFIED FOR USE IN THE OPERATING ENVIRONMENT, MUST BE OF MATERIALS SUITABLE FOR THE ENVIRONMENT IN WHICH THEY ARE INSTALLED, AND MUST BE OF A TYPE SUITABLE FOR THE APPLICATION. COVERS OF BOXES AND CABINETS SHALL BE PAINTED RED AND PERMANENTLY IDENTIFIED AS TO THEIR USE. EXPOSED CABLES SHALL BE SUPPORTED BY THE STRUCTURAL COMPONENTS OF THE BUILDING SO THAT THE CABLE WILL NOT BE DAMAGED BY NORMAL BUILDING USE. EXPOSED CABLES MUST BE SECURED BY STRAPS, STAPLES, CABLE TIES, HANGERS, OR SIMILAR FITTINGS DESIGNED AND INSTALLED TO NOT DAMAGE THE CABLE. POWER LIMITED FIRE ALARM CABLES SHALL NOT BE STRAPPED TO THE EXTERIOR OF ANY RACEWAY AS A MEANS OF SUPPORT. FIRE ALARM CIRCUITS MUST BE IDENTIFIED AT ALL TERMINAL AND JUNCTION BOX LOCATIONS. FIRE ALARM CABLE SPLICES OR TERMINATIONS SHALL BE MADE IN LISTED FITTINGS, BOXES OR ENCLOSURES FIRE ALARM DEVICES OR UTILIZATION EQUIPMENT. FIRE ALARM CIRCUITS LOCATED IN NON -ACCEPTABLE LOCATIONS OR BELOW 8 FEET MUST BE INSTALLED IN METALLIC CONDUIT. THIS INCLUDES AREAS BEHIND HARD CEILINGS AND DRYWALL. All DIRECT BURIAL FIRE ALARM CABLE NOT PROTECTED IN CONDUIT MUST BE INSTALLED AT A MINIMUM DEPTH OF 24" BELOW GRADE WITH EITHER SCHEDULE 80 NORTH PVC OR RIGID CONDUIT UP TO THE DEVICE. DIRECT BURIAL CABLE INSTALLED IN i FIRE ALARM PLAN PLASTICCONDUIT 80 UIT MUST BE INSTALLED AT A MINIMUM OF 1 8" BELOW GRADE IN SCHEDULE 1 Scale. 1/8 - 1-0 CONSULTANT: SEAL: SEAN PATRICK PIC-KELL, PE 83946 ` G. s F / 0 ; No.83948 STATE OF F A THIS DRAWING SHALL NOT BE USED FOR CONSTRUCTION PURPOSES 'UNTIL THE SEAL AND SIGNATURE OF THE RESPONSIBLE REGISTRANT APPEARS ON THE DRAWING, AND PROPER PERMIT FORMS AND RELATED FEES ARE TRANSMITTED BY THE OWNER, OWNER'S AGENT OR CONTRACTOR TO THE AUTHORITY HAVING JURISDICTION. DATE ISSUED FOR REV 03/29/2021 PEMB COORDINATION 05/20/2021 CIVIL SUBMISSION 05/20/2021 DUKE COORDINATION 06/07/2021 PEMB COORDINATION 02 08/09/2021 CIVIL RESUBMISSION 1 08/25/2021 OWNER REVIEW 1 1 /08/2021 REVISED ELEVATIONS 1 1 /29/2021 PERMIT SUBMITTAL Project Manager Drawn L. LONG N. NGUYEN Project Leader Checked L. LONG S. PIC-KELL Date Dept Mgr Approval 02/23/2021 M. GOOD Client PALMETTO ZEPHYRHILLS - GALL BLVD., LLC P.O. Box 1615, Thomasville, GA 31 799 Office: (229) 226-1 177 Contact: Daniel Tubb Project DOLLAR GENERAL Corner of Gall Boulevard and C Avenue, Zephyrhills, FL 33542 (City of Zephyrhills) Store #: 23227 Drawing Title FIRE ALARM PLAN DO NOT SCALE DRAWING Project No. Drawing No. JCDT.20.0451 E6