Laserfiche WebLink
SECTION A <br />SECTION B <br />SECTION- PHARMACY (ROOM 100 <br />1 "= 1'-0" <br />Is <br />O <br />N <br />M <br />N <br />N <br />O <br />N <br />ti <br />6) <br />SECTION C <br />ELEVATION - PHARMACY (ROOM 100 <br />1 /2" = 1'-0" <br />ALTERNATE NO. 1 <br />PROVIDE PLASTIC LAMINATE <br />COUNTERTOPS IN LIEU OF <br />SOLID SURFACE - COLOR TO <br />BE DETERMINED. <br />0 <br />N <br />i <br />SECTION A <br />SECTION B <br />SECTION- PHARMACY- (ROOM 100' <br />ill <br />= 1'-011 <br />-GENERAL NOTES - <br />X XX-X REFER TO SHEET A104 FOR FINISHES. <br />1. PROVIDE BLOCKING IN WALL TO SUPPORT ALL WALL MOUNTED <br />FIXTURES. <br />2. ALL DIMENSIONS TO BE FIELD VERIFIED BY CONTRACTOR PRIOR TO <br />FABRICATION AND INSTALLATION OF MILLWORK. <br />3. THE CONTRACTOR SHALL COORDINATE AND INSURE THAT THE WORK <br />OF OTHER TRADES INSTALLED IN THE MILLWORK IS PERFORMED AS <br />FULLY AND CORRECTLY AS SET FORTH AND DESCRIBED IN THE <br />DRAWINGS AND SPECIFICATIONS. <br />4. ALL EXPOSED SURFACES IN MILLWORK SHALL BE COVERED W/ <br />PLASTIC LAMINATE PER FIN. SCHEDULE. <br />5. ALL CABINETRY PLANS AND DETAILS ARE INTENDED TO EXPRESS THE <br />DESIGN INTENT ONLY. THE CONTRACTOR SHALL SUBMIT DETAILED <br />PLANS FROM THE CABINET MAKER TO THE ARCHITECT FOR APPROVAL <br />PRIOR TO FABRICATION. <br />MILLWORK KEYNOTE <br />Cl:) 3/4" PLYWD. W/ PLASTIC LAMINATE SURFACE. <br />O 3/4" BACKSPLASH SAME FINISH AS ADJOINING COUNTERTOP. <br />0 4" O.C. SATIN ALUMINUM FINISH WIRE PULL. <br />® PLASTIC LAMINATE FINISHED CABINET. <br />05 WHITE MELAMINE FINISH. <br />© ADJUSTABLE SHELVES, PROVIDE SHELF SUPPORT CLIPS. <br />07 1X WOOD BLOCKING AS REQUIRED. <br />® 2X WOOD BLOCKING AS REQUIRED. <br />09 PLUMBING FIXTURE, REFER TO PLUMBING PLANS. <br />10 POWER OUTLET (REFER ALSO TO ELEC. DWGS.). <br />C11D SOLID SURFACE COUNTER/ BACKSPLASH TO MATCH EXISTING. <br />12 BASE (REFER TO FINISH SCHEDULE). <br />13 PLASTIC LAMINATE BACK W/ SLATS. PROVIDE METAL SHELF <br />SUPPORTS. <br />14 3/4" PLYWD. W/ PLASTIC LAMINATE SURFACE ALL SIDES OF <br />SUPPORT BRACKET EXPOSED TO VIEW. <br />15 SLIDE OUT DRAWERS W/ SOFT CLOSE KIT. <br />16 PROVIDE BEVELED OPENING W/ RACK SUPPORT AT REAR OF <br />DOOR - REFER TO MILLWORK SECTIONS. <br />17 PROVIDE SLOT FOR DISPENSER OF GLOVES/ PAPER TOWELS. <br />18 SOAP DISPENSER EQUAL TO PROVON ADX HYGIENE SERIES. <br />19 EQUIPMENT BY OWNER - G.C. TO COORDINATE W/ ELECTRICAL <br />PLUMBING DRAWINGS. <br />20 RED PLEXIGLASS MATERIAL. <br />21 BLUE PLEXIGLASS MATERIAL. <br />22 BD RECYKLEEN CABINET, BY OWNER. <br />23 PROVIDE 6" DIAM OPENING W/ BOBRICK B-529 FOR THRU-COUNTER <br />TRASH HOLE. PROVIDE 4" DIAM AT DENTAL LAB RM. 118. <br />24 ROLL -OUT BASE CABINET ON CASTERS W/ LOCKS. <br />25 CABINET MOUNTED MICROWAVE, BY OWNER. <br />26 3/4" PLYWD. VALENCE LAMINATE W/ CONCEALED LIGHT FIXTURE. <br />27 PROVIDE HARDWARE SET NO. 11 W/ (2) HINGES - SEE SHEET A850. <br />28 AIR SUPPLY LINE - REFER TO PLUMBING DWGS. <br />29 WATER SUPPLY LINE - REFER TO PLUMBING DWGS. <br />30 CLEAR GLASS SLIDING DOORS -1/4" THICK (TEMPERED) W/ LOCK <br />c <br />C� <br />r <br />T <br />ELEVATION - PHARMACY (ROOM 100 <br />1 /2" = 1'-0" <br />THIS DRAWING AND THE DESIGN SHOWN ARE THE PROPERTY OF <br />SPRING ENGINEERING, INC. AND ARE NOT TO BE REPRODUCED, <br />COPIED, PUBLISHED, OR USED IN WHOLE OR PART WITHOUT <br />WRITTEN CONSENT. THEY ARE TO BE USED ONLY FOR THE SITE ANC <br />PROJECT IDENTIFIED AND SHALL BE RETURNED UPON REQUEST. <br />JOB NO. <br />2022-16 <br />SHEET NO. <br />A701 <br />Oft so <br />