|
sustainable 1,0,insulation
<br />Specification Sheet
<br />Metal Building Insulation 202-96
<br />CertainTeed
<br />SAINT-GOBAIN
<br />PRODUCT DESCRIPTION
<br />CertainTeed Metal Building
<br />Basic Use: CertainTeed Fiber Glass Metal Building ^`
<br />Product Name Insulation 202-96
<br />Insulation 202-96 is a flexible blanket insulation
<br />Manufacturer CertainTeed Corporation
<br />furnished in rolls and intended to be laminated on
<br />one side with a suitable vapor retarder. It is used as
<br />Address P.O. Box 860
<br />a thermal and acoustical insulation in the roofs and
<br />Valley Forge, PA 19482-0105
<br />sidewalls of pre-engineered metal buildings and
<br />Phone 610-341-7000 • 800-233-8990
<br />post frame construction.
<br />Fax 610-341-7571
<br />Benefits: Metal Building Insulation 202-96
<br />reduces transmission of exterior sound to the
<br />Website www.certainteed.com/insulation
<br />interior Of the building and absorbs reverberating
<br />sounds within the building.
<br />TECHNICAL DATA
<br />Composition and Materials: The product is composed of tan, uniformly textured, inorganic fibrous
<br />glass and formed with a formaldehyde -free binding agent.
<br />Applicable Standards
<br />Limitations: This product is designed for use in interior (weather protected) walls and roofs of
<br />• Model Building Codes:
<br />pre-engineered metal buildings. It should be laminated on a first -in, first -out basis and should be kept
<br />- ICC
<br />dry at all times during processing and end use. After lamination, packaging should not exceed a 5.5:1
<br />• Material Standards:
<br />compression ratio. For additional information, please refer to the appendix of the NAIMA 202-96 (Rev. - ASTM C991, Type I
<br />2000) standard.
<br />- NAIMA 202-96 (Rev. 2000)
<br />Sizes: Standard available sizes as noted in table below.
<br />Contact CertainTeed for
<br />non-standard sizes.
<br />Fire Resistance
<br />INSTALLATION
<br />Fire Hazard Classification:
<br />THERMAL PERFORMANCE
<br />The vapor retarder on Metal Building
<br />Nominal Thickness
<br />R-Value
<br />- UL 723, ASTM E84, NFPA 255
<br />Max. Flame Spread Index: 25
<br />Insulation 202 96 should be installed toward
<br />(Pre -Lamination)
<br />Max. Smoke Developed Index: 50
<br />the conditioned spaces in the building. The
<br />in. mm
<br />R RSI
<br />- CAN/ULC-S102-M88
<br />Insulation is normally applied over or between
<br />3N 86
<br />10 1.76
<br />the structural members of the building and
<br />31/a 95
<br />11 1.94
<br />Non-combustible:
<br />held in place by the covering sheets or
<br />4Y6 ill
<br />13 2.29
<br />- ASTM El 36 / Meets requirements
<br />insulation support system. When using high
<br />5Ya 133
<br />16 2.82
<br />Physical/Chemical Properties
<br />R-Value systems, it is recommended that the
<br />6% 162
<br />19 3.35
<br />cavity between the exterior metal sheet and
<br />6a/ 171
<br />21 3.70
<br />• Thermal Resistance:
<br />the faced fiber glass insulation should be
<br />8 203
<br />25 4.40
<br />- ASTM C518 and/or ASTM C177 at 75T (24°C)
<br />completely filled.
<br />9/ 235
<br />30 5.30
<br />mean temperature: see table at left
<br />• Acoustical Performance: see tables on other side
<br />• Water Vapor Sorption:
<br />AVAILABLE SIZES
<br />- ASTM C1104 / No greater than 5.0% by weight
<br />R-value Nominal Thickness
<br />Width
<br />I Leno
<br />• Corrosiveness:
<br />R in. rem in.
<br />rem
<br />g in
<br />-ASTM C665 /Meets requirements for steel,
<br />10 3% 76.2 36, 48, 60, 72
<br />914, 1219, 1524,1829
<br />100 30.5
<br />copper and aluminum
<br />11 33A 88.9 36, 48, 60, 72
<br />914,1219,1524,1829
<br />100 30.5
<br />• Odor Emission:
<br />13 4% 101.6 36, 48, 60, 72
<br />914,1219,1524,1829
<br />75 22.9
<br />- ASTM C1304 / Pass
<br />16 5Y4 133.35 36, 48, 60, 72
<br />914,1219,1524,1829
<br />50 15.2
<br />• Fungi Resistance:
<br />19 6% 127 36, 48, 60, 72
<br />914,1219,1524,1829
<br />50 15.2
<br />- ASTM C1338 / Pass Test
<br />21' 63/4 152.4 36,48,60,72
<br />914, 1219,1524,1829
<br />45 13.7
<br />quality Assurance
<br />25' 8 203.2 36, 48, 60, 72
<br />914, 1219, 1524,1829
<br />30 9.1
<br />CertainTeed's commitment to quality and
<br />30' 9A 203.2 36, 48, 60, 72
<br />914,1219,1524,1829
<br />25 7.6
<br />environmental management has ensured the
<br />registration of the Athens. Chowchilla and Kansas
<br />Non-standard widths are available and subject to an upcharge on an individual basis determined by
<br />manufacturer's
<br />City plants to ISO 9001:2000 and ISO 14001:
<br />capability, quantity, lead times and packaging availability. 'R-21,
<br />R-25 and R-30 are made to order.
<br />2004 standards.
<br />EcoTouch° Insulation with PureFiber° Technology
<br />® for Certified R Metal Building
<br />INNOVATIONS FOR LIVING
<br />Product Data Sheet
<br />Typical Physical Properties
<br />Property Test Method _<
<br />Thermal Resistance ASTM 077/C318
<br />Surface Burning
<br />UL 723VASTM E84
<br />Result
<br />(see "Description")
<br />Flame spread index < 25
<br />Smoke developed index < 50
<br />Combustion Characteristics ASTM EI36 Non-combustible
<br />Water Vapor Sorption ASTM C1104 s 0.2% by volume
<br />Fungi Resistance ASTM C1338 Passes - no growth exhibited
<br />Corrosiveness ASTM C665 Passes
<br />Odor Emission ASTM C1304 Passes - no odor detected
<br />I.The surface burning characteristics of these products have been determined in accordance with UL 723. The
<br />❑ R- I 0 3.4' ❑ R- 19, 6.3"
<br />standard should be used to measure and describe the properties of materials, products or assemblies in response to
<br />heat and name under controlled laboratory conditions and should not be used to describe or appraise the fire hazard
<br />❑ R-11, 37' ❑ R-25, 8,0"
<br />or fire risk of materials, products or assemblies under actual fire conditions. However, results of this test may be used
<br />as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of
<br />❑ R- 13, 43' ❑ R-30, 9.25'
<br />the fire hazard of a particular end use. Values are reported
<br />to the nearest 5 rating.
<br />❑ R- 16, 5.3"
<br />• Uses a minimum of 65%
<br />Installation
<br />recycled content 41% being
<br />Several methods are used to
<br />Description
<br />post -consumer
<br />insulate metal buildings. The usual
<br />Owens Corning EcoTouchO
<br />• GREENGUARD Children &
<br />method is to apply the insulation
<br />Insulation with PureFiber®
<br />Schools Certified .
<br />Over the structural members
<br />Technologyfor Certified R
<br />• Easy to handle.
<br />(purlins and girts) and inside the
<br />exterior panels. This method
<br />Metal Building is a light density
<br />• Excellent recovery provides
<br />generally accommodates single
<br />fibrous glass blanket designed to
<br />outstanding thermal and
<br />layer installations. Methods are
<br />be laminated with a variety of
<br />acoustical performance.
<br />also available to apply insulation
<br />appropriate facings. Certified R
<br />Product Applications
<br />between purlins so as to
<br />is available in standard R-values
<br />of 10, 11, 13, 16, 19, 25 and 30.
<br />EcoTo® Insulation with
<br />accommodate greater insulation
<br />Standard roll widths are 36", 48",
<br />PureFi er
<br />PureFiber° Technology for
<br />thicknesses and better thermal
<br />performance.
<br />60" and 72". Selected Made -to-
<br />Certified R Metal Building is used
<br />Order widths are also available.
<br />as part of the insulation system in
<br />the roofs and side walls of metal
<br />Technical Information
<br />Key Features
<br />buildings. It is designed to be
<br />Owens Corning EcOTouch8
<br />laminated with a variety of facings
<br />Insulation with PureFiber
<br />• EcOTouchO insulation is the
<br />to provide attractive interior
<br />Technology for Certified R Metal
<br />only fiberglass insulation
<br />finishes, abuse resistance, and
<br />Building is regularly tested to
<br />product listed in the USDA
<br />assistance in control of moisture.
<br />ensure compliance to the NAIMA
<br />BioPreferredsM Catalog.
<br />202-96 (Rev. 2000) Standard.
<br />• Formaldehyde-free2.
<br />Owens Corning reFib c®®
<br />Insulation with PureFiber
<br />Sampling and testing is performed
<br />• Made with 99% natural'
<br />Technology for Certified R Metal
<br />b the National Association of
<br />Home Builders Research Center
<br />HomeB- fide
<br />materials —not acrylic.
<br />Building are fabricated and
<br />is
<br />The product e
<br />(NAHlabeled
<br />• Made in the U.S.A.'
<br />distributed in a nation wide
<br />network of independent
<br />on the top surface of
<br />laminators assuring prompt service
<br />each roll with the nominal R-value
<br />"NAIMA
<br />and delivery, Contact your Owens
<br />and the 202-96" (Rev.
<br />I. Meets requirements orthe Buy American Act.
<br />Corning Sales Representative for
<br />2000) to indicate compliance.
<br />2. Applies to the insulation component only.
<br />3. Unfaced insulation made with a minimum of 99%by
<br />the names of insulation laminators
<br />The NAIMA 202-96 (Rev. 2000)
<br />weight natural materials consisting of minerals and
<br />servicing your area.
<br />standard specifies thermal
<br />plant -based compounds.
<br />AVAILABILITY AND COST
<br />SOUND ABSORPTION - UNFACED
<br />Manufactured and sold throughout the United States
<br />R-Value Nom. Thickness
<br />Absorption Coefficients @ Octave Band Frequencies (Hz)
<br />and Canada. For availability and cost, contact your
<br />R in. mm
<br />125 250 500 1000
<br />2000
<br />4000
<br />NRC
<br />local distributor or call CertainTeed Sales Support
<br />Group in Valley forge, PA at 800-233-8990.
<br />10 3% 86
<br />0.29 0.82 1.02 0.94
<br />0.96
<br />0.98
<br />0.95
<br />11 34: 95
<br />0.39 0.91 1.01 0.92
<br />0.93
<br />0.98
<br />0.95
<br />WARRANTY
<br />13 4-% ill
<br />0.53 0.97 1.04 0.90
<br />0.95
<br />0.98
<br />0.95
<br />In as much as CertainTeed has no control over
<br />16 5'/a 133
<br />0.67 1.05 1.02 0.92
<br />0.98
<br />0.99
<br />1.00
<br />installation design, installation workmanship,
<br />19 646 162
<br />0.89 1,22 1.02 0.98
<br />1.01
<br />1,00
<br />1.05
<br />accessory materials or conditions of application,
<br />CertainTeed does not warrant the performance or
<br />Sound absorption tested in accordance with ASTM C423 using Type A mounting per ASTM E795.
<br />results of any installation containing its products.
<br />SOUND TRANSMISSION
<br />MAINTENANCE
<br />_
<br />Transmission Loss in dB at the Octave Frequencies
<br />STC
<br />An inspection and preventative maintenance
<br />Construction Type
<br />Rating
<br />program for the insulation and vapor retarder
<br />125 250 500 1000
<br />2000
<br />40DO
<br />system is recommended to ensure optimum
<br />ROOFS
<br />performance.
<br />No Insulation
<br />12 13 19 24
<br />30
<br />32
<br />24
<br />TECHNICAL SERVICES
<br />R-10 Faced 202-96 Insulation Over
<br />me Pudins
<br />12 16 26 37
<br />45
<br />49
<br />29
<br />Technical assistance can be obtained either from
<br />R-19 Faced 202-96Insulation Over
<br />13 20 30 41
<br />49
<br />51
<br />32
<br />the local CertainTeed sales representative, or by
<br />the Pudins
<br />calling CertainTeed Sales Support Group in Valley
<br />202-96Insulation Over & Between
<br />Forge, PA at 800-233-8990.
<br />the Pudins to Fill the cavity (R-25
<br />14 24 34 44
<br />53
<br />56
<br />36
<br />Combined)
<br />FILING SYSTEMS
<br />WALLS
<br />• CertainTeed Pub. No. 30-25-056.
<br />No Insulation
<br />12 14 19 19
<br />20
<br />27
<br />21
<br />• Additional product information available
<br />� 0IFa� 202-96Insulation Over
<br />13 16 25 32
<br />37
<br />46
<br />28
<br />upon request.
<br />R-13 Faced 202-961nsulatbn Over
<br />13 17 26 33
<br />38
<br />47
<br />29
<br />the Girls
<br />R-13 Faced 202-96 Insulation Over
<br />the Girls 3-5/8" Steel Studs on 24"
<br />26 40 51 60
<br />64
<br />65
<br />50
<br />Centers with 1/2" Gyp. Board on
<br />Interior
<br />R-13 Faced 202-96 Insulation Over
<br />the Girls 3-5/8" Steel Studs on 24"
<br />31 43 55 68
<br />73
<br />75
<br />54
<br />Centers with R-11 Batts & 1/2" Gyp.
<br />Board on Interior
<br />Sound Transmission Class (STC) in accordance with ASTM E90.
<br />- Roof constnlction is 24ga. standing seam roof with 8" Z pudins on 5' centers.
<br />- Wall construction is 26ga. wall panels screwed to 8" Z girls plated on T centers.
<br />- Interior metal furring wall studs were 3-5/8" by 25ga. on 24' centers.
<br />Seal and "900152000•
<br />�fW consulate +' •1f I _ NArrs
<br />tE ' REENGUARD ,� �'.� ... ...-.
<br />ENERGY STAR NAIMA
<br />-- Indoor Ai,Qual"r Ceruno�� sr[aEo
<br />ASK ABOUT OUR OTHER CERTAINTEED PRODUCTS AND SYSTEMS:
<br />EXTERIOR: ROOFING • SIDING • WINDOWS • FENCE • RAILING • TRIM • DECKING • FOUNDATIONS • PIPE
<br />INTERIOR: INSULATION • GYPSUM • CEILINGS
<br />CertainTeed Corporation Professional: 800-233-8990
<br />P.O. Box 860 Consumer: 800-782-8777
<br />Valley Forge, PA 19482 www.certainteed.com/insulation
<br />Code No. 30-27-016, ® 10/10 CertainTeed Corporation
<br />CertainTeed
<br />SAINT-GOBAIN
<br />EcoTouch° Insulation with PureFiber Technology
<br />for Certified R Metal Building
<br />INNOVATIONS FOR LNING'
<br />Product Data Sheet
<br />performance which provides the Standards, Codes Environmental and
<br />capability of obtaining nominal Compliance Sustainability
<br />thermal resistance (R-values) . ASTM C991-08, Flexible Owens Corning is a worldwide
<br />after laminating. The actual Fibrous Glass Insulation for leader in building material systems,
<br />thermal performance obtained Metal Buildings; Type I. insulation and composite solutions,
<br />from the laminated product delivering a broad range of high -
<br />will depend primarily on the • NAIMA 202-96 (Rev, 2000) quality products and services.
<br />recovered thickness, Note that Standard for Flexible Fiber Glass Owens Corning is committed to
<br />these nominal R-values are for Insulation to be Laminated for driving sustainability by delivering
<br />the insulation only and do not Use in Metal Buildings. solutions, transforming markets
<br />include the effects of facings, air Certifications and Sustainable and enhancing lives, More
<br />films, compression of insulation at Features of EcoTouchE information can be found at http:H
<br />framing members, conductance Insulation with PureFiber° sustainability.owenscorning.com.
<br />through fasteners, or other heat Technology for Certified R
<br />transfer paths particular to an Metal Building
<br />installation.
<br />• EcoTouch° insulation is the
<br />The recovered thickness achieved only fiberglass insulation
<br />will depend on a number of product listed in the USDA
<br />variables determined in the BioPreferredsM Catalog,
<br />laminating process and hence • Certified by Scientific
<br />are outside of Owens Corning's Certification Systems to contain
<br />control. To address these issues, a a minimum of 65% recycled
<br />number of leading metal building glass content
<br />insulation laminators produce
<br />products which meet the • Certified to meet indoor air
<br />National Insulation Association's quality standards underthe
<br />"Certified Faced Insulation stringent GREENGUARD
<br />Standard" (NIA 404). Samples of Indoor Air Quality Certification
<br />faced products are periodically Programsm, and the
<br />tested by a nationally recognized GREENGUARD Children & laboratory and determined to Schools Certification ProgramsM
<br />meet the NIA standard.
<br />USDA
<br />CERTIFIED
<br />BIOBASED
<br />PRODUCT
<br />PRODUCT 57",
<br />rp�na® N A H B
<br />RESEARCH
<br />smaadcormn C E N TER/i ctdd,E" a s,"om,
<br />Technical information
<br />ationq REENGUARD GUARD"'
<br />Technical information contained herein is furnished G R E E N
<br />without charge or obligation and is given and accepted at «...,• APPROVED QIndoor Air Quality Certified ndoor Air Quality Certified
<br />recipient's sole risk. Because conditions of use may vary
<br />and are beyond our control, Owens Corning makes no
<br />representation about, and is not responsible or liable for
<br />the accuracy or reliability ofdata associated with particular OWENS CORNING INSULATING SYSTEMS, LLC
<br />uses of any product described herein. ® ONE OWENS CORNINGPARKWAY
<br />Scient�cCertificationSystems (SCS)provides independent • TOLEDO, OHIO, USA43659
<br />verification of recycled content in building materials and • P 1-800-GET-PINK'
<br />verifies recycled content claims made by manufacturers. INNOVATIONS FOR LIVING' www.owenscorningcommercial.com
<br />For more information, visit www. scscertified.com.
<br />Pub. No.15086-R. Printed in U.S.A. September 2012, THE PINK PANTHER"
<br />The GREENGUARD INDOORAIRQUALITY CERTIFIED &@1964-2012 Metro -Goldwyn -Mayer Studios Inc. All Rights Reserved -The
<br />Mark is a registered certification mark used under license colorPINKisaregistered trademarkof0wensCorning.02012Owens Corning.
<br />through the GREENGUARD Environmental Institute. All Rights Reserved.
<br />Product Data Sheet
<br />All-purpose foam panel
<br />insulation for masonry and
<br />other applications.
<br />Owens Corning FOAMULAR 150 extruded
<br />polystyrene insulation is ideal for wall
<br />furring, perimeter/foundation, cavity
<br />wall, crawispace, pre -cast concrete, under
<br />slab, sheathing and other applications.
<br />Owens Corning's patented Hydrovac"
<br />process technology makes the unique
<br />closed -cell structure of FOAMULAR
<br />insulation highly resistant to moisture,
<br />retaining its initial R-value* year after
<br />year - even following prolonged exposure
<br />to water leakage, humidity, condensation.
<br />ground water and freeze/thaw cycling.
<br />FOAMULAR 150 Performance Benefits
<br />• High R-value (R-5 per inch of product
<br />thickness)!
<br />• Compressive strength of 15 psi.
<br />• Effective resistance against moisture,
<br />mildew, corrosion and rot.
<br />• Ease of handling and installation
<br />(lightweight, tough, rigid foam panels).
<br />• Easy to saw, cut and score.
<br />• Wide selection of sizes and thicknesses.
<br />• Availability in straight, tongue and
<br />groove, or scored square edges.
<br />• Compliance with building codes and
<br />standards.
<br />FOAMULAR 150
<br />Superior Insulation Performance for a
<br />Wide Variety of Building Requirements
<br />Product Applications
<br />High-performance FOAMULAR 150
<br />works to:
<br />• Retard the transmission of water vapor
<br />and moisture in masonry walls, helping
<br />prevent structural damage.
<br />• Provide insulation in a metal or wood
<br />furring system used for masonry or
<br />concrete walls.
<br />• Perform below grade in perimeter and
<br />foundation applications, or on -grade
<br />directly beneath the concrete slab to
<br />complement the insulating sheathing
<br />envelope around the building framing.
<br />Resistant to common soils and decay,
<br />Owens Corning FOAMULAR retains its
<br />insulating performance characteristics even
<br />after prolonged exposure to moisture.
<br />Standards and Codes Compliance
<br />• Recognized by code authorities under
<br />Research Reports BOCA 91-54;
<br />ICBO 3628; SBCCI PST & ESI 9727
<br />• Meets HUD/FHA Use of Materials
<br />Bulletin No. 71 and ASTM C 578-92
<br />Type X
<br />• Underwriters Laboratories, Inc.,
<br />Classification Certificate U-197
<br />• Thermal resistance: 5.0 at 75 °F,
<br />5.4 at 40 *F mean temperature and
<br />1" thickness (hr x ft' x °FBtu)
<br />FOAMULAR 150
<br />Rigid Foam Insulation
<br />Technical Information
<br />• FOAMULAR insulation is ideal for all
<br />buildings under normal temperature
<br />conditions, but should not be used in
<br />contact with chimneys, heater vents,
<br />steam pipes or other surfaces where
<br />temperatures exceed 150-F. It is not
<br />recommended for applications where
<br />sustained temperatures exceed 165'F.
<br />• All construction should be evaluated for
<br />the necessity to provide vapor retarders.
<br />See current ASHRAE Handbook of
<br />Fundamentals.
<br />• FOAMULAR insulation in a non-
<br />structural material and must be installed
<br />on framings which are independently
<br />structurally adequate to meet required
<br />construction and service loading
<br />conditions.
<br />*The higher the R-value, the greater the insulating power. Ask your seller for the fact sheet on R-values.
<br />J► ALPHA
<br />high pertormonce fabrics & composites
<br />ALPHA ASSOCIATES. INC. • 145 LEHIGH AVE. • LAKEWOOD, NJ 08701
<br />T: 732.634.5700 • 800.831,6399 • F: 732.634.1430
<br />VR-R PLUS
<br />DESCRIPTION
<br />Reinforced Polypropylene Film - Metalized Polyester Film Laminate
<br />APPLICATIONS
<br />Metal Building Insulation Facing
<br />CERTIFICATIONS
<br />Meets all criteria for ASTM C1136 Types II, IV UL 723/ASTM E84, ULC-S102M fire testing
<br />COMPOSITION
<br />VALUES*
<br />COMPONENT
<br />DESCRIPTION
<br />English
<br />Metric
<br />White Film
<br />Polypropylene
<br />0.0011 inch
<br />28.0 micron
<br />Adhesive
<br />Flame Resistant
<br />Reinforcement
<br />Tri-directional Fiberglass
<br />4/inch (MD)
<br />20/100 mm (MD)
<br />4/inch (CD)
<br />8/100 mm (MD)
<br />Film
<br />Polyester
<br />0.0005 inch
<br />12.7 micron
<br />TYPICAL PHYSICAL PROPERTIES
<br />VALUES*
<br />CHARACTERISTIC
<br />METHOD
<br />ENGLISH
<br />METRIC
<br />BASIS WEIGHT
<br />Scale
<br />13.2 Ibs/1000 SF
<br />64.1 g/SM
<br />THICKNESS
<br />ASTM-D-1777
<br />0.007"
<br />178 microns
<br />PERMEABILITY (WVTR)
<br />ASTM-E-96
<br />0.02 Perms
<br />1.15 ng/N's
<br />BURST STRENGTH
<br />ASTM-D-774
<br />100 psi
<br />7.0 kg/cm2
<br />PUNCTURE RESISTANCE ASTM-C-1136
<br />300 units (79 in-Ibs)
<br />9.0 Joules
<br />TENSILE STRENGTH
<br />ASTM-C-1136
<br />30 Ibs/inch MD
<br />5.25 kN/m
<br />30 Ibs/inch CD
<br />5.25 kN/m
<br />ACCELERATED AGING
<br />30 days @
<br />No Corrosion
<br />No Corrosion
<br />95% RH, 120 °F (49°C)
<br />No Delamination
<br />No Delamination
<br />TEMPERATURE RESISTANCE
<br />-40 °F to 220 °F
<br />-40 °C to 104 °C
<br />WATER IMMERSION
<br />24 hours @ 73°F (23°C)
<br />No Delamination
<br />No Delamination
<br />MOLD RESISTANCE
<br />ASTM-C-665
<br />No Growth
<br />No Growth
<br />LIGHT REFLECTIVITY
<br />ASTM-C-523
<br />85%
<br />85%
<br />Physical properties are based upon nominal values.
<br />Weight / Thickness +/- 10%
<br />FIRE TESTING
<br />UL723/ASTM E84/CAN ULC-S102M
<br />Composite
<br />FLAME SPREAD
<br />25
<br />SMOKE DEVELOPED
<br />50
<br />DATA SHEET q 13662 REV. I DATE: 12/10/14 *All values are nominal unless otherwise specified.
<br />Note: Alpha's metal building insulation facings are produced with plastic films containing ultraviolet (UV) inhibitors, however,
<br />intense exposure to UV sources such as direct or indirect sunlight and/or high -output UV lighting is not recommended as
<br />these will degrade the plastic film facing.
<br />FOAMULAR 150 Rigid Foam Insulation
<br />FOAMULAR Physical Properties"'
<br />Product Data
<br />Caution
<br />Product /Values
<br />Foamular Insulation Product- 150 (15psi)"'
<br />This product will ignite if exposed to fire of
<br />ASTM FOAMULARMaterial
<br />"' Property Method 1500PYst
<br />Extruded polystyrene closed -cell
<br />Y
<br />sufficient heat and intensity. This product
<br />foam panel with continuous skins
<br />should be installed only with a gypsum
<br />Thermal conductivity - "k"'
<br />on face and back surfaces
<br />board on the interior side of the wall.
<br />[Btu x in/ft' x hr x IF max]
<br />@ 75°F mean temperature C518 0.20
<br />Width x
<br />During shipping, storage, installation and
<br />@ 40°F mean temperature 0.18
<br />Thkknesses"' (In) Lengthl"(In) Edges
<br />use, this product should not be exposed
<br />Compressive strength,
<br />1, 1Y4 2, 2X, 3 16 x 96 Square
<br />to open flame or other ignition sources.
<br />Minimum (specification) D1621 15.0
<br />1, 1%, 2, 14, 3, 3Ye 24 x 96 Square
<br />value (lb/in')"'
<br />1, 1%, 2, 2 4, 3 48 x 96 Square
<br />Note
<br />Flexural strength
<br />(lb/in' min)", C203 60
<br />1 48 x 108 Square
<br />All products described here may not be
<br />Water absorption
<br />Scored
<br />available in all geographic markets.
<br />(% by volume max)", C272 0.10
<br />1, 1% 2, 2%, 3 48 x 96 Square
<br />Consult your local sales office
<br />Water vapor permeance
<br />1, 1%, 2 24 x 96 T&G"'
<br />representative for more information.
<br />(perm max)'" E96 0.80
<br />1, 1%, 2 48 x 96 T&G'•'
<br />Water affinity - hydrophobic
<br />1 48x108 T&GGD
<br />Technical Information:
<br />Water capillarity - none
<br />Weight Approximately 120-1301b1
<br />(800) 828-7155
<br />Dimensional stability
<br />1,000 ft'' for 1" thickness
<br />(% linear change max)'"' D2126 2.0
<br />Export Sales Office:
<br />Linear coefficient of thermal
<br />Packaging Shipped in units with two stretch-
<br />(330) 633-1105
<br />expansion (in/ieF max) - 2.7xlW
<br />wrap bands per bundle, with an
<br />Flame spread"M1" E84 5
<br />additional exterior wrap
<br />FOAMULAR insulation is produced by
<br />Smoke developed""'°"I" E84 45-175
<br />FOAMULAR Insulation Product - CW-15
<br />Owens Corning's patented HYDROVAC•
<br />Oxygen index min"' D2863 24
<br />I 1':- 2 16 x 96 Square
<br />process technology.
<br />(1) Properties shown are representative values for
<br />I" thick material based upon most recent product
<br />( I ) "R" per inch: 5.0 (at 75°F mean temperature).
<br />For more information on the
<br />quality audit data. (2) Modified as required to meet
<br />(2) Other sizes available on request. Consult your
<br />Owens Corning family of home building
<br />ASTM C578-92. (3) Thermal resistance (R) -
<br />(hr. x ft.' x *FBtu) -of a 1" thickness at 5.0
<br />local Owens Corning representative for availability.
<br />(3) Compressive strength, minimumP
<br />P S (specification)
<br />roducts, contact our Owens Coming
<br />Y g
<br />(at 75•F mean temperature), 5.4 (at 40°F). (4) Value
<br />value (lb/in'). (4) Tongue -and -groove edge reduces
<br />dealer, call 1 - 8 0 0 - G E T - P I N K
<br />at yield. (5) Value at yield or 5%, whichever occurs
<br />air infiltration.
<br />or access our Web site:
<br />first. (6) Data ranges from 0.00 to value shown due to
<br />Note: All products described here may not be
<br />the level of precision of the test method. (7) Actual
<br />available in all geographic markets. Consult your
<br />w w w. o w e n s c o r n i n g. c o m
<br />water vapor permeance data decreases as thickness
<br />local Owens Corning sales office or representative
<br />increases. (8) Data ranges from 0.0 to value shown.
<br />for information.
<br />(9) These laboratory tests are not intended to describe
<br />the hazard presented by this material under actual fire
<br />conditions. (10) Data from Underwriters Laboratories,
<br />Inc! classified. See Classification Certificate U-197.
<br />(11) ASTM E84 is thickness -dependent, therefore a
<br />range of values is given.
<br />�® SYSTEM THINKING
<br />• :blokes the Differeurv'"
<br />OWENS CORNING WORLD HEADQUARTERS
<br />ONE OWENS CORNING PARKWAY
<br />TOLEDO, OHIO 43659
<br />System Thinking- and System Thinking Makes the Difference" are trademarks of Owens Corning.
<br />The color PINK is a registered trademark of Owens Corning.
<br />0 & r'" designate names and products which are trademarks of Owens Corning.
<br />Pub. No. 5-FO-23513-A Printed in U.S.A., October 2001 Copyright @ 2001 Owens Corning
<br />Zabik Turner Engineering, PLLC
<br />Jennifer Zabik, P.E., S.E.
<br />1024 N Fullers Cross Road
<br />Winter Garden, FL 34787
<br />j zabik@ztengineering.com
<br />P-1294
<br />SEALS
<br />.� ENS'°
<br />No. M
<br />5
<br />ST ty
<br />' 10,VC /
<br />� R10
<br />NAt-
<br />RAPID
<br />BUILDING SOLUTION'S,
<br />3 5 0 E Crown Point Rd
<br />Suite 1080
<br />Winter Garden, FL 34787
<br />Phone: (40 7) 34 7-9614
<br />Info@
<br />rapidbuildingsolutions. com
<br />JOB NAME:
<br />Zephyrhills Commons
<br />38001 Pretty Pond Road
<br />Zephyrhills, FL
<br />JOB NUMBER:
<br />268-19-ZEP-FL
<br />REV
<br />DATE
<br />DESCRIPTION
<br />APP
<br />1
<br />11-28-19
<br />Layout Review
<br />JL
<br />0
<br />12-16-19
<br />Review
<br />RG
<br />1
<br />12-19-19
<br />RBS RL
<br />RG
<br />2
<br />12-20-19
<br />ZTE RL
<br />RG
<br />3
<br />01
<br />—21 —20
<br />CUST. REDLINES
<br />RG
<br />4
<br />01
<br />—22-20
<br />REVIEW
<br />RG
<br />5
<br />01
<br />—24-20
<br />HECTOR RL
<br />AC
<br />6
<br />03-08-20
<br />Review 1
<br />RC
<br />ISSUE DATE: Novermber 28,2019
<br />DESIGNED BY: RBS DRAWN BY: JL
<br />CHECKED BY: RBS SUBMITTED BY: CSD
<br />8ft 4ft Oft 8ft 1 6ft
<br />1 /8"=1 '—O"
<br />DETAILS: NOT TO SCALE
<br />APPROVED FOR PRODUCTION
<br />INITIALS OF GC/OWNER
<br />RBS-IN. I
<br />
|