|
Q
<br />1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12 1 13 1 14 1 15 1 16 1 17 1 18
<br />.w .
<br />t
<br />r
<br />19 1 20
<br />P
<br />0
<br />N
<br />M
<br />L
<br />K
<br />J
<br />H
<br />G
<br />F
<br />E
<br />u
<br />C
<br />B
<br />A
<br />PLUMBING PROJECT NOTES
<br />1. THE CONTRACTOR SHALL ARRANGE AND PAY FOR ALL PERMITS
<br />14. SANITARY PIPING SCHEDULES:
<br />AND INSPECTIONS REQUIRED IN THIS WORK.
<br />A) VENTS - SCHEDULE 40 PVC DWV.
<br />2. ALL WORK SHALL BE DONE IN ACCORDANCE WITH THESE PLANS,
<br />B) BUILDING DRAIN -SCHEDULE 40 PVC DWV.
<br />SPECIFICATIONS, LOCAL, STATE AND NATIONAL CODES. CERTIFICATES
<br />OF INSPECTION, WHERE REQUIRED, SHALL BE OBTAINED AND PAID
<br />15. DOMESTIC WATER PIPING SCHEDULES:
<br />FOR BY THIS CONTRACTOR AND FURNISHED TO THE TENANT.
<br />INTERIOR ABOVE GRADE - TYPE "L" HARD DRAWN COPPER
<br />TUBE.
<br />3. THE CONTRACTOR SHALL FURNISH ALL LABOR, MATERIALS,
<br />EXTERIOR BELOW GRADE - TYPE "K" HARD DRAWN COPPER
<br />EQUIPMENT AND TOOLS TO PERFORM MECHANICAL WORK AS SHOWN,
<br />TUBE WITH FLARED FITTINGS.
<br />NOTED OR SCHEDULED FOR A COMPLETE INSTALLATION.
<br />16, ALL VALVES AND SPECIALTY ITEMS MAY NOT BE SHOWN IN
<br />4. ALL MATERIALS AND EQUIPMENT SHALL BE NEW AND COMMERCIAL
<br />EVERY INSTANCE ON THE DRAWINGS, BUT ARE TO BE PROVIDED
<br />GRADE.
<br />WHETHER SHOWN OR NOT WHEN NECESSARY FOR PROPER
<br />OPERATION AND MAINTENANCE OF THE SYSTEM. UNLESS
<br />5. THE CONTRACT DRAWINGS INDICATE THE EXTENT AND GENERAL
<br />OTHERWISE NOTED, VALVES AND SPECIALTY ITEMS ARE TO BE
<br />ARRANGEMENTS OF EQUIPMENT AND SYSTEMS. IF ANY DEPARTURES
<br />RATED AT 125 PSIG. DEVICES AND VALVES 2 1/2" AND SMALLER ARE
<br />FROM THE CONTRACT DRAWINGS ARE DEEMED NECESSARY BY THE
<br />TO HAVE SOLDERED OR SCREWED CONNECTIONS.
<br />CONTRACTOR, DETAILS OF SUCH DEPARTURES AND REASONS
<br />THEREFORE SHALL BE SUBMITTED TO THE OWNER FOR APPROVAL.
<br />17. PIPING SYSTEM INSULATION:
<br />POTABLE COLD WATER PIPING - ALL PIPING ABOVE CEILING OR
<br />EXPOSED TO THE EXTERIOR WITH 1" THICK FIBERGLASS OR 1/2"
<br />6 IT IS THE INTENT OF THE PLANS AND SPECIFICATIONS TO PROVIDE
<br />FLEXIBLE UNICELLULAR.
<br />A COMPLETE AND OPERATING INSTALLATION INCLUDING ALL
<br />POTABLE HOT WATER. - ALL SUPPLY PIPING WITH 1" THICK
<br />OBVIOUSLY NECESSARY ITEMS EVEN THOUGH SOME ITEMS MAY NOT
<br />BE INDICATED ON THE DRAWING OR SPECIFICATIONS.
<br />FIBERGLASS OR 1/2" THICK FLEXIBLE UNICELLULAR, EXCEPT THE
<br />FIRST EIGHT LINEAL FEET OF HOT WATER SUPPLY PIPING SHALL BE
<br />7. ALL OBVIOUS ERRORS AND/OR OMISSIONS IN THE ABOVE MENTIONED
<br />MINIMUM OF 1" THICK INSULATION.
<br />DOCUMENTS SHALL BE CALLED TO THE ATTENTION OF THE ARCHITECT /
<br />SANITARY- ALL PIPING EXPOSED TO THE EXTERIOR WITH 2" THICK
<br />ENGINEER PRIOR TO CONSTRUCTION.
<br />FIBERGLASS OR 1" FLEXIBLE UNICELLULAR.
<br />18. FIXTURES:
<br />8. THIS CONTRACTOR SHALL INSPECT THE JOB SITE WHERE THE
<br />A) PLUMBING FIXTURES SHALL BE FURNISHED AND
<br />WORK IS TO BE PERFORMED AND SHALL AQUAINT THEMSELF WITH THE
<br />CONDITIONS UNDER WHICH IT SHALL BE EXECUTED.
<br />INSTALLED IN ACCORDANCE WITH THE SCHEDULE AS SHOWN ON
<br />THE PLANS. ALL FIXTURES SHALL BE COMPLETE WITH HANGERS,
<br />9. PROVIDE DIELECTRIC UNIONS OR FITTINGS WHENEVER FERROUS
<br />CARRIERS, TRIM, STOP VALVES AND OTHER ACCESSORIES AS
<br />AND NON-FERROUS PIPES ARE JOINED.
<br />REQUIRED TO OBTAIN A COMPLETE INSTALLATION.
<br />B) AMERICANS WITH DISABILITIES ACT (A.D.A.): ALL HANDICAP
<br />FIXTURES AND TRIM SHALL COMPLY WITH FEDERAL AND STATE
<br />10. PROVIDE ACCESS DOORS WHERE NECESSARY TO SERVICE SEALS,
<br />ACCESSIBILITY CODES. NOTE: WATER CLOSET FLUSH VALVE
<br />VALVES, TRAPS, CLEANOUTS, WATER HAMMER ARRESTORS, ETC.
<br />CONTROLS SHALL BE MOUNTED ON THE WIDE SIDE OF TOILET
<br />AREAS NO MORE THAN 44 INCHES ABOVE THE FLOOR.
<br />11. CONTRACTOR TO VERIFY SIZE AND LOCATIONS OF ALL
<br />EXISTING SERVICES PRIOR TO COMMENCING WITH NEW WORK.
<br />19. ALL PIPING INSTALLED ON THE PROJECT SHALL BE
<br />COORDINATE ALL CLEANOUTS WITH ARCHITECTURAL PRIOR TO
<br />HYDRAULICALLY TESTED, FLUSHED AND DISINFECTED.
<br />INSTALLATION.
<br />20. .ALL PARTS, MATERIAL, EQUIPMENT AND LABOR FURNISHED
<br />12. EVERY TRAP SHALL BE PROTECTED AGAINST SYPHONING AND
<br />SHALL BEAR A ONE (1) YEAR, NO COST TO B.O.S., WARRANTY FROM
<br />BACK PRESSURE. AIR CIRCULATION SHALL BE ASSURED BY MEANS
<br />DATE OF FINAL ACCEPTANCE. THE PLUMBING CONTRACTOR SHALL
<br />OF A SOIL OR WASTE STACK VENT, A CONTINUOUS SOIL OR WASTE
<br />PROVIDE ALL OF THE ABOVE WARRANTY REQUIREMENTS IN A
<br />VENT OR CIRCUIT VENT.
<br />WRITTEN STATEMENT ALONG WITH EQUIPMENT MANUFACTURER'S
<br />WARRANTIES.
<br />13. ALL VENT PIPES PASSING THROUGH THE ROOF SHALL BE
<br />FLASHED AS REQUIRED BY GENERAL CONTRACTOR.
<br />20. VERIFY EXISTING LOCATIONS AND INVERTS OF PIPING.
<br />VB O
<br />O 3/4" COLD WATER SUPPLY
<br />BALL VALVE (TYP)
<br />AMTROL EXPANSION
<br />6
<br />ABSORBER #AST-5
<br />3/4"
<br />12
<br />O
<br />13
<br />3/4" 3/4"
<br />3/4" 3d 110 DEGREE F HOT WATER SUPPLY
<br />7
<br />O REFER PLUMBING SCHEDULE (WH-1).
<br />14 O 11
<br />32"
<br />O2 PROVIDE HEAT TRAP (MIN. 12" OFFSET).
<br />O 3/4"
<br />-I I O T & P RELIEF VALVE.
<br />7
<br />3/4"
<br />PRESSURE TYPE VACUUM BREAKER.
<br />O O®
<br />7
<br />6 (D BALL & CHECK VALVE
<br />©WATER HEATER WALL MOUNT PLATFORM
<br />WITH INTEGRAL DRAIN PAN.
<br />OHOLDRITE MODEL 40-SWHP-W.
<br />9
<br />10 FACTORY ENGINEERED MOUNTING
<br />7 HARWARE INCLUDED WITH ASSEMBLY.
<br />O
<br />G.C. SHALL PROVIDE BLOCKING AND STUDS
<br />FOR SUPPORT AS REQUIRED BY MFR.
<br />1"
<br />(DDIELECTRIC UNION
<br />MOUNT AS
<br />O ROUTE AND OFFSET DRAIN LINE FULL SIZE
<br />HIGH AS
<br />AND AIR GAP 2" ABOVE MOP SINK BOTTOM.
<br />POSSIBLE
<br />10 ROUTE AND OFFSET T&P LINE FULL SIZE
<br />NI AND AIR GAP 4" ABOVE MOP SINK BOTTOM.
<br />11 MIXING VALVE - 80°F THRU 120°F
<br />12 THERMOMETER. TRERICE #AO0507 W/
<br />#138-0015.2 WELL
<br />MOP SINK 13 BALL VALVE
<br />FINISH FLOOR 14 ELECTRICAL BY ELECTRICAL CONTRACTOR.
<br />., a ,
<br />ELECTRICAL WATER HEATER DETAIL
<br />NO SCALE
<br />FINISHED FLOOR FLOOR DRAIN
<br />FLASHING
<br />r ,
<br />s L .
<br />• a.
<br />• IIIII
<br />e
<br />s." L
<br />' e
<br />• s
<br />s a L s
<br />TRAP PRIMER PIPING
<br />UNION
<br />TRAP PRIMER CONNECTION DETAIL
<br />NOT TO SCALE
<br />ENSURE NO OFFSETS
<br />L:
<br />OR SLOPE MORE
<br />THAN 2%.
<br />Twh
<br />L '.
<br />TAILPIECE
<br />OD TUBING
<br />SLIP JOINT
<br />CHROME
<br />WALLCOVEF
<br />AND SCREN,
<br />"WCO"
<br />WALL CLEANOUT DETAIL
<br />NOT TO SCALE
<br />"P"TRAP DETAIL
<br />NOT TO SCALE
<br />PLUMBING FIXTURE UNIT SCHEDULE
<br />QUANTITY
<br />DESCRIPTION
<br />WATER
<br />DEMAND
<br />SANITARY
<br />FIXTURE UNIT (F.U.) (EACH)
<br />FIXTURE
<br />UNITS (TOTAL)
<br />FIXTURE UNIT (F.U.)
<br />COLD
<br />HOT
<br />COMB.
<br />COLD
<br />HOT
<br />COMB.
<br />F.U. (EACH)
<br />F.U. (TOTAL)
<br />1
<br />DRINKING FOUNTAIN
<br />0.25
<br />0
<br />0.25
<br />0.25
<br />0.00
<br />0.25
<br />1.50
<br />1.50
<br />2
<br />FLOOR DRAINS
<br />0
<br />0
<br />0
<br />0.00
<br />0.00
<br />0.00
<br />2.00
<br />4.00
<br />2
<br />LAVATORY (PUBLIC)
<br />1.50
<br />1.50
<br />2.00
<br />3.00
<br />3.00
<br />4.00
<br />2.00
<br />4.00
<br />1
<br />SERVICE SINK
<br />2.25
<br />2.25
<br />3.00
<br />2.25
<br />2.25
<br />3.00
<br />2.00
<br />2.00
<br />2
<br />WATER CLOSET, PUBLIC FLUSH TANK
<br />5
<br />0
<br />5
<br />10.00
<br />0.00
<br />10.00
<br />4.00
<br />8.00
<br />1
<br />KITCHEN SINK
<br />1.00
<br />1.00
<br />1.40
<br />1.00
<br />1.00
<br />1.40
<br />2.00
<br />2.00
<br />0
<br />URINAL
<br />5.00
<br />0
<br />5.00
<br />0.00
<br />0.00
<br />0.00
<br />2.00
<br />0.00
<br />9
<br />TOTAL:
<br />1&50
<br />6.2,'i
<br />1&65
<br />-
<br />21.50
<br />NOTES:
<br />1) SYSTEM WILL REQUIRE 1" WATER MAIN. 1" EXISTING.
<br />2) SYSTEM WILL REQUIRE A MINIMUM 3" BUILDING DRAIN (1/8" SLOPE). 4" INSTALLED..
<br />B.O.S. PLUMBING FIXTURE SCHEDULE
<br />MARK
<br />DESCRIPTION
<br />FIXTURE MFG.
<br />CATALOG NO.
<br />TRIM MFG.
<br />CATALOG NO.
<br />REMARKS
<br />NOTE
<br />CONNECTION
<br />SIZES
<br />W
<br />V
<br />C
<br />H
<br />WC-1 HL
<br />WATER CLOSET-ADA-LEFT SIDE FLUSH VALVE
<br />AMER. STD.
<br />3043.001
<br />SLOAN
<br />111-YBYC-YO
<br />OLSONITE SEAT #95-SS, 3/8" BRASS BOLTS
<br />3
<br />3"
<br />2"
<br />1"
<br />- -
<br />WCA HR
<br />WATER CLOSET-ADA-RIGHT SIDE FLUSH VALVE
<br />AMER. STD.
<br />3043.001
<br />SLOAN
<br />111-YBYC-YO
<br />OLSONITE SEAT #95-SS, 3/8" BRASS BOLTS
<br />3
<br />3"
<br />2"
<br />1"
<br />- -
<br />L-1 H
<br />LAVATORY - WHITE - WALL HUNG - HANDICAP
<br />AMER. STD.
<br />0355.012
<br />SYMMONS
<br />S-20-2-G-FR-VP
<br />Z-1231-79 CARRIER
<br />1-2-3-5
<br />2"
<br />2"
<br />1/2"
<br />1/2"
<br />EWC-H
<br />ELECTRIC WATER COOLER - HANDICAP
<br />ELKAY
<br />EZSTL-8-C
<br />ELKAY
<br />LKAPR-EZL
<br />ADA APRON
<br />1-2-3
<br />2"
<br />2"
<br />1/2"
<br />-
<br />MS
<br />FLOOR MOP SINK 24"X24"X10"
<br />MUSTEE
<br />63M
<br />MUSTEE
<br />63.600A
<br />63CM KIT -SINK, FAUCET, HOSE, MOP HANGAR, STRAINER, PIPE SEAL
<br />1-2-6
<br />3"
<br />2"
<br />1/2"
<br />1/2"
<br />CS
<br />COUNTER SINK, 5 1/2" DEEP MOUNT IN COUNTER SURFACE
<br />ELKAY
<br />LRAD1918553
<br />AMER. STND.
<br />6409.170.002
<br />PROVIDE DRAIN STRAINER, RECESS MOUNT, 3-HOLE 4" O.C.
<br />1-2
<br />2"
<br />2"
<br />1/2"
<br />1/2"
<br />RW
<br />REFRIGERATOR WATER CONNECTION -HAMMER VALVE
<br />OATEY
<br />39152 (1 ONLY)
<br />MAKE CONNECTION TO OWNER PROVIDED REFRIGERATOR
<br />- -
<br />- -
<br />1/2"
<br />- -
<br />BV
<br />BALL VALVE
<br />APOLLO
<br />70-200
<br />AS REQUIRED BY PLAN.
<br />- -
<br />-
<br />- -
<br />- -
<br />WCO
<br />WALL CLEANOUT
<br />ZURN
<br />Z1446
<br />PVC PLUG WITH BRONZE INSERT W/THREADS TO MATCH COVER
<br />- -
<br />- -
<br />- -
<br />- -
<br />FD
<br />FLOOR DRAIN
<br />ZURN
<br />ZS415NL-VP-P
<br />INSTALL FLUSH WITH FINISHED FLOOR. CONNECT TO TRAP PRIMER (TP)
<br />3"
<br />- -
<br />TP
<br />TRAP PRIMER
<br />PPP
<br />P-1
<br />--
<br />-
<br />1/2"
<br />--
<br />VB
<br />VACUUM BREAKER - PRESSURE TYPE
<br />WATTS
<br />N36
<br />LOCATE & SIZE AS PER MFG. INSTRUCTIONS
<br />WHA
<br />WATER HEATER - ELECTRIC - 20 GAL. - 2KW NON-SIM.
<br />RHEEM
<br />EGSP20
<br />SEE DETAIL. (208V)
<br />- -
<br />- -
<br />- -
<br />PLUMBING NOTES: GENERAL NOTES:
<br />(1) MCGUIRE CAST BRASS P-TRAP WITH TUBULAR WALL BEND (SIZE AS REQUIRED). P-TRAPS IN CONCEALED (A) ALL PLUMBING FIXTURES SHALL BE WHITE.
<br />SPACES MAY BE PVC. (B) PROVIDE ONLY PRIOR APPROVED MANUFACTURERS.
<br />(2) MC GUIRE LAWSINK SUPPLY STOP #H2165CCLK WITH CHROME RISER TUBE. (C) SEE ARCHITECTURAL DRAWINGS FOR TOILET ACCESSORIES (SOAP DISPENSERS, DRYERS, ETC. AND ELEVATIONS.
<br />(3) SET AT HANDICAP HEIGHT. (D) VERIFY PIPE SIZES FOR "BV", "FD", "ECO", "WCO" OR OTHER COMPONENTS.
<br />(4) REQUIRED IN MEN'S AND WOMEN'S TOILET ROOM UNDER LAVATORY. (E) KOHLER MAY BESUBSTITUTED FOR AMERICAN STANDARD PLUMBING FIXTURES.
<br />(F) BENEKE MAY BE SUBSTITUTED FOR OLSONITE SEATS.
<br />(5) TRUEBRO LAV GUARD: MODEL NO. 102W FOR P-TRAP AND ANGLE STOPS WITH SUPPLY ASSEMBLIES. (G) BRASSCRAFT MAY BE SUBSTITUTED FOR MCGUIRE.
<br />MODEL NO. 102W WITH 105 ACCESSORY FOR OFFSET DRAIN.
<br />(6) PROVIDE THE MUSTE 63CM KIT THAT PROVIDES THE MOP SINK(63M), FAUCET / FAUCET HANGER(63.600A), HOSE AND
<br />HOSE HOLDER BRACKET(65.700), DRAIN SEAL(65.309), STRAINER(INCL.W/ SINK), AND MOP HOLDER BRACKET(65.600).
<br />KIT AVAILABLE AT GRAINGER, GRAINGER #11 U264.
<br />1 ' 2 3 ' 4 1 5
<br />6
<br />7
<br />8
<br />9
<br />10
<br />MAY EXTEND AS A
<br />WASTE OR VENT
<br />WALL
<br />PLUGGED TEE
<br />WITH CLEANOUT
<br />FLOOR LINE
<br />1/8" C.I. BEND
<br />_ BALANCE OF PIPING SAME
<br />AS CLEANOUT OT GRADE
<br />IE
<br />F
<br />TREADS
<br />CONNECT TO TEES
<br />AS REQUIRED
<br />12
<br />2 V /Ole
<br />^\
<br />/// 1 \ 2"V
<br />\ REUSE EXISTING
<br />r 1 \� ROOF PENETRATION
<br />i \ 3" VTR
<br />\ \ 3 V
<br />I I I \\
<br />I I \ I
<br />CONNECT TO EXISTING SITE I 2"V 1 \
<br />SANITARY. FIELD VERIFY I I \\ 1
<br />EXACT LOCATION, INVERT I 4 I 12"V \ v \ I \ \
<br />AND FLOW DIRECTION. 1 \ 3"V
<br />I 1 \ 1 100, \\
<br />z"v 1 i I \\\ le� 001 \
<br />I
<br />I
<br />EWC-H 2„
<br />MS1
<br />2"
<br />3"
<br />13
<br />14
<br />15
<br />IR
<br />WCO
<br />16
<br />D
<br />3"
<br />SANITARY RISER
<br />NOT TO SCALE
<br />ME3
<br />CONSULTING ENGINEERS, LLC
<br />5300 Paylor Lane
<br />Sarasota, FL 34240
<br />Tel:941-748-1319 Fax:941-361-1221
<br />www.me3-engr.com sidney@me3-engr.com
<br />Designed: BAK ME3 Job No: B17-1166
<br />Checked: BAK Date: 09/29/2017
<br />Drawn: KCC C.O.A.27552
<br />Copyright 2017 ME3 All rights reserved
<br />P
<br />IN
<br />N
<br />M
<br />L
<br />K
<br />J
<br />H
<br />G
<br />F
<br />REV. DESCRIPTION DATE
<br />BID & PERMIT SET E
<br />09.29.17
<br />CURRENT ISSUE STATUS:
<br />"To the best of the Architect's or
<br />Engineer's knowledge, the plans
<br />and specifications comply with the
<br />applicable minimum building codes
<br />and applicable fire safety standards
<br />as determined by local authority in
<br />accordance with Chapter 553 and
<br />663 of Florida Statutes."
<br />(17
<br />Kay C. Clem
<br />Florida License # 53270
<br />WBRCIENI.
<br />ARCHITECTS ENGINEERS
<br />8130 Lakewood Main Street Phone: 941-556-0757
<br />Suite 210 Fax: 941-556-0759
<br />Lakewood Ranch, FL 34202 www.wbrcae.com
<br />Firm Lic. # AA26001395 & 27389 Douglas W.Whitney AIA
<br />BEALLS OUTLET #542
<br />ZEPHYRHILLS
<br />PROJECT: 6030 Gall Blvd, Zephyrhills, FL 33542 B
<br />SHEET TITLE:
<br />WBRC CAD FILE:
<br />PROJECT No. 3542XX GRAPHIC SCALE:
<br />0„
<br />SCALE: As Indicated I I A
<br />PLUMBING PLAN PROJECT MANAGER
<br />SHEET No.
<br />1 /4" _ 1 i_Off N DRAWN BY: P 101
<br />CHECKED BY:
<br />17 18 19 20
<br />PLUMBING PLAN
<br />
|