|
AI
<br />(
<br />FIRE ALARM SPECIFICATIONS & GENERAL NOTES
<br />HVAC WIRING GENERAL NOTES
<br />1. DUCT DETECTOR RELAY WIRING SHALL BREAK 24VOLT
<br />ELECTRICAL MOUNTING BOX
<br />I. GENERAL SCOPE:
<br />COIL
<br />SECONDARY CONTROL SYSTEM POWER AT THE AIR
<br />FOR THE CEILING MOUNTED
<br />HANDLER UNIT.
<br />NOTIFICATION DEVICES.
<br />A. THIS PROJECT WILL REQUIRE THE INSTALLATION OF A NEW FIRE ALARM SYSTEM FOR A RETAIL OUTLET STORE. THE EXISTING SYSTEM WILL BE REMOVED. AS INDICATED ON THESE
<br />2. IF ADDRESSABLE DUCT DETECTORS ARE USED, THE
<br />PLANS, BEALLS/BURKES REQUIRES THE INSTALLATION OF A DIGITAL MONITORING PRODUCTS (DMP) XR150DNFC-R SYSTEM. THE PANEL/SYSTEM SPECIFIED IS REQUIRED BY THE OWNER
<br />RELAY WILL BE NORMALLY CLOSED DURING
<br />IN ORDER TO MAINTAIN CONSISTENCY THROUGHOUT THEIR STORES. DEVIATIONS WILL NOT BE ACCEPTED UNLESS APPROVED, IN WRITING, BY BEALLS/BURKES CONSTRUCTION MANAGER.
<br />NON -ALARM CONDITIONS AND OPEN UPON ALARM
<br />TO CAUSE A POWER LOSS D THE HVAC CONTROL
<br />/
<br />BLOWER RELAY
<br />CIRCUIT, RESULTING IN FAN AND COMPRESSOR
<br />PROVIDE BATTERIES AS REQUIRED BY THE FIRE ALARM BATTERY CALCULATIONS.
<br />SHUTDOWN.
<br />c
<br />PROVIDE BATTERIES AS REQUIRED BY THE POWER SUPPLY EXPANDER CALCULATIONS.
<br />0
<br />3. IF CONVENTIONAL RELAYS (NON -ADDRESSABLE) ARE
<br />c
<br />000
<br />THE RELAY SHALL BE NORMALLY OPEN
<br />o
<br />II. REQUIREMENTS:
<br />cu
<br />(SED,
<br />UNPOWERED) AND SHALL BE HELD CLOSED BY THE
<br />vt� FROM THERMOSTAT
<br />FIRE ALARM PANEL UNTIL THE DUCT SMOKE
<br />�o
<br />DETECTOR IS IN AN ALARM CONDITION.
<br />A. THE INSTALLATION SHALL CONFORM TO THE INTENT OF NFPA 72 (2010 ED.), THESE PLANS, AND APPLICABLE REFERENCED DOCUMENTS.
<br /><w
<br />FUSE z�
<br />4. IN SYSTEMS PROVIDED WITH A FAN SHUTDOWN DELAY
<br />B. SECONDARY POWER SHALL CONSIST OF RECHARGEABLE BATTERIES HAVING A CAPACITY TO POWER THE ALARM SYSTEM FOR A PERIOD OF 24 HOURS IN A STANDBY MODE AND OPERATE
<br />oQ
<br />CIRCUIT, A PROGRAMMABLE RELAY SHALL BE
<br />PROVIDED IN SERIES WITH THIS EQUIPMENT TO
<br />ALL NOTIFICATION APPLIANCES FOR 5 MINUTES AT THE END OF THE 24 HOUR PERIOD.
<br />raw
<br />BREAK THE CIRCUIT ON ADDRESSABLE SYSTEMS OR
<br />"CADDY" T-GRID BOX
<br />HANGER o
<br />W]L
<br />PROVIDED WITH A NORMALLY OPEN RELAY THAT IS
<br />SUPPORT, OR EQUAL.
<br />"CADDY"
<br />C. ALL CIRCUITS SHALL BE "POWER LIMITED". THE CIRCUIT TYPES SHALL BE INSTALLED AS INDICATED BELOW:
<br />AHU STEP DOWN 00
<br />TRANSFORMER �ai
<br />HELD CLOSED DURING NORMALLY SYSTEM OPERATION
<br />ON CONVENTION SYSTEMS.
<br />REFERENCE NO. CEC 30-302( 3)
<br />INITIATION DEVICE CIRCUITS (IDC'S): CLASS "B"
<br />U
<br />ACOUSTICAL TILE CEILING
<br />NOTIFICATION ALARM CIRCUITS (NAC'S): CLASS "B"
<br />JQ
<br />GRID SUPPORT FRAMING.
<br />D. WALL -MOUNTED NOTIFICATION HORN/STROBES ARE TO BE MOUNTED SO THAT THE ENTIRE LENS OF THE DEVICE IS NO LESS THAT 80" AFF AND NO GREATER THAN 96" AFF.
<br />ff
<br />oW
<br />CEILING -MOUNTED NOTIFICATION DEVICES ARE TO BE MOUNTED AT A MAXIMUM HEIGHT OF 30 FT. (AS INDICATED ON THE PLANS)
<br />zL_
<br />E. ALL NEW PULL STATIONS SHALL BE INSTALLED AT 48 INCHES ABOVE THE FINISH FLOOR.
<br />F.NG CONNECTIONS ARE TO BE IN SINGLE, DOUBLE, TRIPLE OR 4 INCH ELECTRICAL BOXES, AS NEEDED. WIRING CONNECTIONS OUTSIDE OF ELECTRICAL BOXES WILL NOT BE
<br />A
<br />B
<br />ALLOWED.
<br />FIRE ALARM DUCT DETECTOR
<br />SHUTDOWN WIRING
<br />CEILING
<br />GRID ELECTRICAL BACK -BOX ATTACHMENT
<br />G. ALL WIRING ON THE INITIATION AND NOTIFICATION CIRCUITS ARE SUPERVISED POWER LIMITED.
<br />FA 1 0 1 .NOT TO SCALE
<br />FA 1 0 1 NOT TO SCALE
<br />H. SURGE SUPPRESSION DEVICES SHALL BE INSTALLED ON ALL CIRCUITS THAT ENTER OR EXIT THE BUILDING. TYPICAL DEVICES ARE LISTED BELOW:
<br />PANEL POWER: DITEK MODEL DTK-120SRD, (OR EQUAL)
<br />INITIATING CKTS: DITEK MODEL DTK-2MHLP-WB, (OR EQUAL)
<br />PHONE LINES: DITEK MODEL DTK-MRJ31 XSCPWP, (OR EQUAL)
<br />PANEL POWER SURGE SUPPRESSION MODULE TO BE CONNECTED TO FIRE ALARM CONTROL PANEL; SO THAT WHEN THE MODULE TRIPS, THE FIRE ALARM CONTROL PANEL SHALL REPORT
<br />A SUPERVISORY CONDITION.
<br />FIRE ALARM
<br />CIRCUIT TO
<br />JUNCTION BOX NEXT DEVICE
<br />I. STROBE CIRCUITS SHALL BE SYNCHRONIZED EITHER THROUGH THE MAIN FACP OR SEPARATE SYNCHRONIZATION MODULES (AS NECESSARY).
<br />(OR EQ)
<br />III. CONDUIT AND WIRE
<br />FIRE ALARM DEVICE MOUNTING
<br />GUIDE
<br />A. CONDUIT
<br />L
<br />I LDETECTOR
<br />CEIUNG MOUNTED
<br />SMOKE/HEAT
<br />�3' (MIN) NOT TO SCALE
<br />1. CONDUIT INSTALLATION SHALL BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (NEC), LOCAL AND STATE REQUIREMENTS.
<br />-1
<br />PER NFPA 72 CEILING 4"
<br />2. CONDUIT FILL WILL NOT EXCEED 40 PERCENT OF INTERIOR CROSS SECTIONAL AREA WHERE THREE OR MORE CABLES ARE CONTAINED WITHIN A SINGLE CONDUIT.
<br />24 MIN HANDICAP
<br />UNISTRUT SUPPORT
<br />BEDROOM STROBE
<br />A/C SUPPLY DIFFUSER ACCEPTABLE HER
<br />4"
<br />3. CABLE MUST BE SEPARATED FROM ANY OPEN CONDUCTORS OF POWER, OR CLASS 1 CIRCUITS, AND SHALL NOT BE PLACED IN ANY CONDUIT, JUNCTION BOX OR RACEWAY
<br />MEMBER OR DIRECT
<br />AUDIOVISUAL DO NOT INSTA
<br />..
<br />CONTAINING THESE CONDUCTORS.
<br />ATTACHMENT TO
<br />VISUAL -ONLY IN THIS AREA
<br />N
<br />STRUCTURAL STEEL.
<br />DEVICES CEILING MOUNTED NOTIFICA
<br />B. WIRE:
<br />MOU
<br />DEVICE (TO BE WHO :�j. WALL MOUNTED
<br />SEE PLAN FOR LOCATION. HEAT DETECTO
<br />1. ALL FIRE ALARM WIRING SHALL BE A MINIMUM OF 'FPLP' TYPE CABLE.
<br />CONDUIT DROP TO
<br />TO THE BOTTOM.
<br />NOTIFICATION DEVICE
<br />MINIMUM 3/8" A.T.R.
<br />WALL MOUNTED
<br />2. WIRING WILL BE IN ACCORDANCE WITH LOCAL, STATE AND NATIONAL CODESNEC ARTICLE 760). THE NUMBER AND SIZE OF CONDUCTORS SHALL BE AS INDICATED ON THESE
<br />(E.G.,( )
<br />DROP TO DEVICE
<br />BACKBOX
<br />__A
<br />5�_0 SMOKE DETECTOR
<br />TO THE TOP.
<br />PLANS, BUT SHALL NOT BE LESS THAN #18 AWG FOR INITIATING DEVICE CIRCUITS (INCLUDING SIGNALING LINE CIRCUITS) AND #14 AWG FOR NOTIFICATION DEVICE CIRCUITS.
<br />MORE THAN TWO APPLL4NCES
<br />IN THE SAME ROOM OR ADJACENT
<br />TYP MAX FROM
<br />EXIT DOOR
<br />SPACE WITHIN THE FIELD OF VIEW
<br />3. ALL FIELD WIRING OF INITIATION AND NOTIFICATION CIRCUITS ARE TO BE COMPLETELY SUPERVISED BY END OF LINE DEVICES, PER THE MANUFACTURER'S LITERATURE.
<br />SHALL FLASH IN SYNCHRONIZATION.
<br />MANUAL
<br />4. HORIZONTAL WIRE RUNS ABOVE CEILINGS: HORIZONTAL WIRE RUNS IN AREAS CONTAINING DROP CEILINGS MAY BE 'FREE -WIRED' IF SUPPORTED BY TO THE BUILDING STRUCTURE.
<br />srnULLL
<br />LAYING WIRE ON THE CEILING OR INADEQUATE SUPPORT OF WIRING FROM THE STRUCTURE WILL NOT BE ALLOWED.
<br />THIS DETAIL APPLIES TO
<br />REMOTE
<br />MOUNT AT HEIGHT
<br />HORN/STROBE DEVICES
<br />80" MIN
<br />96" MAX
<br />ANNUNCIATOR
<br />5. VERTICAL AND HORIZONTAL WIRE RUNS IN OPEN STRUCTURE AREAS: ALL WIRING IN "OPEN TO STRUCTURE AREAS" ON THIS PROJECT SHALL BE INSTALLED IN CONDUIT.
<br />INSTALLED IN THE SALES TO
<br />MATCH LIGHT FIXTURE ELEVATION
<br />NFPA 72
<br />�®
<br />AREA. DEVICES IN THE
<br />6. VERTICAL WIRE RUNS: VERTICAL WIRE RUNS TO DEVICES, PANELS, ANNUNCIATORS, ETC. SHALL BE INSTALLED IN CONDUIT PER THE NATIONAL ELECTRICAL CODE.
<br />SHIPPING/RECEIVING AREA
<br />CAN BE MOUNTED ON
<br />FIREAARM
<br />C. TERMINAL BOXES, JUNCTION BOXES AND CABINETS: ALL BOXES AND CABINETS SHALL BE UL LISTED FOR THEIR USE AND PURPOSE.
<br />BOTTOM OF STRUCTURE.
<br />HORNSTROBE SEE
<br />" (��G)
<br />80 ABOVE HIGHEST FLOOR
<br />PLAN)
<br />LEVEL OR 6" BELOW CEILING
<br />;
<br />D. THE FIRE ALARM CONTROL PANEL IS TO BE CONNECTED TO A SEPARATE DEDICATED BRANCH CIRCUIT, MAXIMUM 20 AMPERES. THIS CIRCUIT SHALL BE LABELED AT THE MAIN POWER
<br />TO THE BOTTOM OF THE
<br />x
<br />DISTRIBUTION PANEL AS FIRE ALARM. FIRE ALARM CONTROL PANEL PRIMARY POWER WIRING SHALL BE 12 AWG. THE CONTROL PANEL CABINET SHALL BE GROUNDED SECURELY TO EITHER
<br />STROBE. WHICHEVER IS LOWER.
<br />48" (ADA)
<br />0 "
<br />A COLD WATER PIPE OR GROUNDING ROD. A 120 VOLT SURGE SUPPRESSER SHALL BE INSTALLED ON THE AC POWER AND GROUNDED PRIOR TO ENTERING THE FIRE ALARM CONTROL
<br />TO THE WORKING MECHANISM
<br />48" ALSO MEETS THE
<br />a 0
<br />as
<br />PANEL. THE BREAKER FOR THE ALARM CIRCUIT SHALL BE RED IN COLOR, OR PAINTED RED, SHALL BE ACCESSIBLE ONLY TO AUTHORIZED PERSONNEL, AND SHALL BE IDENTIFIED WITH A
<br />REQUIREMENTS OF NFPA 72
<br />PERMANENTLABEL AS "FIRE ALARM CIRCUIT". THE LOCATION OF THE DISCONNECTING MEANS SHALL BE PERMANENTLY IDENTIFIED AT THE FIRE ALARM CONTROL UNIT VIA A LABEL INSIDE
<br />C
<br />FINISHED
<br />THE
<br />PENDENT NOTIFICATION
<br />DEVICE MOUNTING
<br />FLOOR
<br />IV. EXECUTION
<br />FA 101 NOT TO SCALE
<br />A. INSTALLATION:
<br />1. INSTALLATION SHALL BE IN ACCORDANCE WITH THE NEC, NFPA 72, LOCAL AND STATE CODES, AS SHOWN ON THE DRAWINGS, AND AS RECOMMENDED BY THE MAJOR EQUIPMENT
<br />MANUFACTURER.
<br />2. DURING CONSTRUCTION MEASURES SHALL BE TAKEN TO PROTECT SMOKE DETECTORS FROM CONTAMINATION AND PHYSICAL DAMAGE UNTIL CONSTRUCTION ACTIVITIES ARE COMPLETE.
<br />V. PROGRAMMING
<br />1. A BASELINE PROGRAMMING MATRIX HAS BEEN INCLUDED ON THESE PLANS.
<br />2. ALL SMOKE DETECTORS SHALL BE PROGRAMMED FOR ALARM VERIFICATION.
<br />VI. FINAL INSPECTION
<br />1. AT THE FINAL INSPECTION A FACTORY TRAINED REPRESENTATIVE OF THE INSTALLER SHALL DEMONSTRATE THAT THE SYSTEMS FUNCTION PROPERLY IN EVERY RESPECT. ALL TESTING
<br />REQUIRED BY THE AHJ SHALL BE COMPLETED IN THE PRESENCE OF THE LOCAL FIRE AUTHORITY, AS REQUIRED.
<br />2. DUCT SMOKE DETECTORS AND THEIR ASSOCIATED RELAY CONTROL INTERFACE WITH THE ASSOCIATED AIR HANDLER UNIT SHALL BE TESTED PRIOR TO THE FINAL INSPECTION WITH THE
<br />LOCAL AHJ. THE PURPOSE OF THE PRE -TEST IS TO ENSURE THE DETECTORS AND SHUTDOWN INTERFACE WITH THE ASSOCIATED AIR HANDLER UNITS ARE FUNCTIONING CORRECTLY
<br />PRIOR TO LOCAL JURISDICTION INSPECTION.
<br />VII. SYSTEM MONITORING
<br />1. ALARM, SUPERVISORY, AND TROUBLE SHALL BE MONITORED VIA A REMOTE SUPERVISING STATION, AS INDICATED ON THESE PLANS.
<br />VIII. GENERAL
<br />1. THE VOLTAGE DROP CALCULATIONS SHOWN ON THE PLANS ARE BASED ON THE CIRCUIT ROUTING SHOWN. MAJOR CHANGES TO THE CIRCUIT ROUTING SHOWN MAY NEED TO BE
<br />JUSTIFIED BY THE FIRE ALARM CONTRACTOR WITH ADDITIONAL CALCULATIONS.
<br />2. THE ALARM CONTRACTOR WILL BE REQUIRED TO SUBMIT A "RECORD OF COMPLETION", PER NFPA 72, TO THE OWNER PRIOR TO FINAL PAYMENT.
<br />3. THE FIRE ALARM CONTRACTOR IS REQUIRED TO MAINTAIN A COMPLETE AND ACCURATE AS -BUILT DRAWING SET. UPON FINAL COMPLETION OF THE PROJECT, THE FIRE ALARM
<br />CONTRACTOR SHALL SUPPLY THE OWNER & HATCHER ENGINEERING WITH AN AS -BUILT SET PRIOR TO FINAL PAYMENT. AS-BUILTS SHALL INDICATE ALL CHANGES TO THE ORIGINAL
<br />LAYOUT INCLUDING, BUT NOT NECESSARY LIMITED TO, AS -BUILT DEVICE LOCATIONS, PANEL LOCATIONS, CIRCUIT ROUTING, CONDUIT ROUTING, JUNCTION BOX LOCATIONS, PANEL
<br />CIRCUIT BREAKER LOCATIONS, ETC.
<br />4. ALL CONDUIT AND WIRING PENETRATIONS THROUGH FIRE RATED BARRIERS (INCLUDING WALLS AND FLOORS), AND SMOKE BARRIERS THAT EXTEND FROM FLOOR TO CEILING, SHALL BE
<br />SEALED WITH A UL LISTED FIRESTOPPING PENETRATION SYSTEM. THE MINIMUM PENETRATION RATING FOR FIRE RATED BARRIERS SHALL MATCH THE RATING OF THE WALL \ FLOOR \
<br />BARRIER. SMOKE BARRIERS SIMPLY NEED TO BE SEALED TO PREVENT THE PASSAGE OF SMOKE THROUGH THE ASSEMBLY.
<br />BEALLS
<br />BURKES OUTLET FIRE ALARM SYSTEM INSTALLATION OVERVIEW
<br />SCARSDALE SECURITY SYSTEMS
<br />INC.
<br />OWNER & FIRE ALARM INSTALLER'S RESPONSIBILITIES:
<br />STEP TWO:
<br />OVERVIEW
<br />PROGRAM THE PANEL WITH THE CORRECT LAN SETTINGS (FOR MONITORING BY SCARSDALE
<br />SCARSDALE SECURITY SYSTEMS IS THE MONITORING COMPANY FOR ALL BEALL'S &
<br />SECURITY):
<br />OWNER WILL PURCHASE AND DELIVER (TO THE JOBSITE) THE FIRE ALARM EQUIPMENT FOR
<br />BURKES STORES. THE FIRE ALARM SYSTEM MUST BE PROGRAMMED TO REPORT TO
<br />EACH PROJECT. SCARSDALE SECURITY WILL BE THE FIRE ALARM EQUIPMENT DEALER. THE
<br />THE SCARSDALE CENTRAL STATION AND ALL SIGNALS MUST BE TESTED BEFORE THE
<br />THE FOLLOWING IS THE BASIC SETUP
<br />INFORMATION REQUIRED PROGRAMMED INTO THE
<br />FOLLOWING IS A BASIC RESPONSIBILITY LIST:
<br />SYSTEM CAN BE PUT ON LINE. THE
<br />PREFERRED TRANSFER PROTOCOL IS CONTACT ID. COMMUNICATOR:
<br />OWNER WILL SUPPLY (VIA SCARESDALE SECURITY) THE FOLLOWING:
<br />IP COMMUNICATOR LOCAL ADDRESS:
<br />ACQUIRE FROM PROJECT MANAGER
<br />REQUIRED STEPS:
<br />SUBNET MASK:
<br />255.255.255.0
<br />• L
<br />GATEWAY:
<br />ACQUIRE FROM PROJECT MANAGER
<br />• DMP/ALTRONICS 6.5 AMP POWER SUPPLY
<br />1. PROVIDE THE CENTRAL STATION WITH ZONE LIST WITH PANEL MAKE & MODEL.
<br />• DMP NOTIFICATION MODULE
<br />2. TEST ALL SIGNALS INTO THE CENTRAL STATION AND CALL TO CONFIRM PROPER
<br />STEP THREE:
<br />• DMP REMOTE ANNUNCIATOR
<br />RECEPTION.
<br />• FIRE ALARM DEVICES (PULL STATIONS, SMOKE DETECTORS, DUCT SMOKE DETECTORS,
<br />3. MAKE THE SYSTEM ACTIVE WITH THE CENTRAL STATION.
<br />TRIP ALL ZONES INTO THE CENTRAL STATION INCLUDING LOW BATTERY AC FAIL. CALL THE
<br />NOTIFICATION DEVICES, MODULES, ETC.)
<br />CENTRAL STATION AT 914-722-2222,
<br />MAKE THE SYSTEM ACTIVE WITH THE CENTRAL STATION AND
<br />• OWNER WILL PREPARE A DEVICE TAKE -OFF LIST FROM THE SHOP DRAWINGS ON EACH
<br />TO IDENTIFY THE CORRECT SYSTEM TO THE CENTRAL STATION YOU MUST PROVIDE
<br />TELL THEM TO PUT THE FIRE SYSTEM
<br />ON LINE. TEST THE CENTRAL STATION REPORTING FOR
<br />SYSTEM AND ORDER/DELIEVER DEVICES SPECIFIC TO THIS PROJECT TO THE JOBSITE.
<br />THEM WITH THE FOLLOWING INFORMATION:
<br />BOTH THE PHONE LINE CONNECTION AND THE ETHERNET CONNECTION.
<br />THE FIRE ALARM CONTRACTOR WILL BE RESPONSIBLE FOR THE FOLLOWING:
<br />- STORE NAME & NUMBER, CITY &
<br />STATE
<br />FIRE INSPECTIONS:
<br />• PROVIDE ALL LABOR, WIRING, ELECTRICAL BOXES, CONDUIT, WIRE HANGAR SUPPORTS,
<br />AND MISCELLANEOUS ELECTRICAL MATERIAL, IN ORDER TO COMPLETE THE INSTALL OF
<br />STEP ONE:
<br />SPECIAL INSTRUCTIONS FOR SUCCESSFULLY
<br />PASSING A FIRE INSPECTION WITH THE FIRE MARSHAL.
<br />THE DMP SYSTEM EQUIPMENT PROVIDED BY BEALLS/BURKES.
<br />• INSTALLATION PERMIT FROM THE LOCAL MUNICIPALITY.
<br />PROVIDE THE CENTRAL STATION WITH
<br />A ZONE LIST. IF IT IS SMALL IT CAN BE CALLED
<br />THE SYSTEM MUST BE ACTIVE WITH
<br />THE CENTRAL STATION THIS MEANS YOU MUST HAVE SENT
<br />• PROVIDE FULL SYSTEM INSTALLATION &TESTING IN ACCORDANCE WITH NFPA 72 AND
<br />INTO THE CS AT 914-722-2222. IF
<br />IT IS LARGE, FAX IT TO 914-722-2299. BE
<br />THE CENTRAL STATION A
<br />THE LOCAL AHJ.
<br />SURE THE ACCOUNT NUMBER IS WRITTEN ON THE FAX. EXAMPLE: 51-5555.
<br />ZONE LIST AND TESTED SIGNALS.
<br />• PROVIDE ALL PROGRAMMING AND CLOSE OUT DOCUMENTATION.
<br />• TEST AND VERIFY FINAL CONNECTION TO THE REMOTE MONITORING STATION
<br />YOU MUST ALSO TELL THE CENTRAL
<br />STATION THE MANUFACTURER & MODEL NUMBER
<br />CALL THE CENTRAL STATION BEFORE
<br />THE FIRE INSPECTIONS START AND TELL THEM YOU ARE
<br />(SCARSDALE SECURITY).
<br />OF THE FIRE ALARM CONTROL PANEL. EXAMPLE: DMP-XR10ONFC
<br />TESTING THE SYSTEM WITH
<br />THE FIRE MARSHAL TODAY AND CONFIRM
<br />THE SYSTEM IS ACTIVE.
<br />RECORD YOUR CELL PHONE NUMBER
<br />AND COMPANY NAME ON THE ZONE LIST SO THE
<br />CS CAN CONTACT YOU IF THEY HAVE
<br />A QUESTION ABOUT THE ZONE LIST.
<br />MAKE SURE THE CS HAS THE PROPER
<br />FIRE DEPARTMENT DISPATCH NUMBER
<br />PROPOSED FIRE ALARM
<br />I
<br />z
<br />Z
<br />CONTROL MATRIX
<br />Z
<br />W
<br />�
<br />>
<br />u'
<br />I-
<br />H
<br />Vl
<br />�
<br />� �+
<br />W
<br />1-
<br />J
<br />''^^
<br />z
<br />c.�
<br />H
<br />a
<br />Z iZ
<br />w o �
<br />f-
<br />a
<br />�
<br />vi
<br />O
<br />H
<br />Z
<br />Z
<br />!-
<br />r¢-(
<br />�
<br />N
<br />Z
<br />E Q ' Q
<br />¢
<br />U
<br />LeJ
<br />�
<br />Q
<br />2
<br />Z
<br />� V~1 W
<br />Val
<br />z
<br />""e
<br />Z
<br />Z
<br />O
<br />'O
<br />Q
<br />J
<br />z
<br />>-
<br />o
<br />a
<br />=
<br />O l7
<br />~� �w
<br />z'
<br />I
<br />I¢
<br />INPUTS O
<br />�
<br />¢
<br />W�
<br />y
<br />�
<br />(-+
<br />a
<br />Z W
<br />�N �=
<br />H
<br />N
<br />A
<br />i
<br />BI
<br />SMOKE DETECTOR
<br />C
<br />X
<br />X
<br />DUCT SMOKE DETECTOR
<br />D
<br />X
<br />X
<br />X
<br />E
<br />X
<br />X
<br />_..._.........----._.
<br />F..._._
<br />X
<br />i X_
<br />MANUAL PULL STATION
<br />G
<br />X
<br />X
<br />'X
<br />H
<br />SYSTEM TROUBLE CONDITION
<br />I
<br />I
<br />J
<br />PANEL POWER SURGE SUPPRESSION MODULE TRIP
<br />K
<br />1 2 3 4 5 6 7' 8
<br />PROJECT SPECIFIC NOTES: I
<br />1. ALL SMOKE DETECTORS ARE TO BE PROGRAMMED WITH ALARM VERIFICATION.
<br />2. THIS CHART IS TO BE USED AS A BASIC PROGRAMMING GUIDE ONLY. ALL OTHER PANEL
<br />PROGRAMMING FEATURES SHALL COMPLY WITH NFPA 72 AND THE MANUFACTURERS
<br />INSTRUCTIONS.
<br />FIRE ALARM DEVICE LEGEND
<br />SYMBOL
<br />DEVICE TYPE
<br />DEVICE MODEL
<br />ADDITIONAL NOTES
<br />SYMBOL
<br />DEVICE TYPE
<br />DEVICE MODEL
<br />ADDITIONAL NOTES
<br />®
<br />FIRE ALARM CONTROL PANEL
<br />DMP XR150NFC-R
<br />©
<br />MAN1',�.I_ PULL STATION
<br />DMP 850S WITH 711 ADDRESSABLE
<br />MODULE
<br />INSTALL AT48^AFF
<br />®
<br />REMOTE ANNUNCIATOR PANEL
<br />DMP 630E-R
<br />INSTALL AT 60" AFF
<br />�
<br />SYSTEM SENSOR D4120 WITH 711
<br />COORDINATE WITH HVAC CONTRACTOR.
<br />INSTALL DETECTOR IN
<br />®
<br />SURGE SUPPRESSION MODULE
<br />`' D
<br />DUCT SMOKE DETECTOR
<br />ADDRESSABLE MODULE
<br />SUPPLY SIDE DUCT
<br />(DOWNSTREAM OF HVAC FAN UNIT)
<br />®
<br />FIRE ALARM POWER SUPPLY
<br />DMP AX-AL602ULADA (ALTRONICS)
<br />�
<br />PHOTOELECTRIC SMOKE DETECTOR
<br />DMP 521 B
<br />CEILING MOUNTED DEVICES TO BE WHITE
<br />FLOW SWITCH
<br />HORN /STROBE (CEILING MOUNTED)
<br />SYSTEM SENSOR BK-PC2W
<br />DEVICE TO BE 'WHITE'
<br />Q3xp
<br />STROBE (CEILING MOUNTED)
<br />SYSTEM SENSOR BK-SCW
<br />DevlcE To BE'wHIrE�
<br />TAMPER SWITCH
<br />�/1N�
<br />END -OF -LINE RESISTOR (EOL)
<br />VENDOR INSTALLED
<br />AT END OF CIRCUIT
<br />WEATHERPROOF
<br />HORN STROBE WALL MOUNTED
<br />SYSTEM SENSOR BK-P2RK
<br />DEVICE TO BE'RED'
<br />a
<br />REMOTE TEST/RESET SWITCH
<br />SYSTEM SENSOR BK-RTS151 KEY
<br />MOUNT ON CEILING BELOW DUCT
<br />DETECTOR. LABEL PER RTU #.
<br />1 `J LU
<br />NATHANIEL J. HATCHER, P.E.
<br />2108 W. RISK STREET
<br />PLANT CITY, FLORIDA
<br />FAX: (813) 752 6901�
<br />Via° 'y�i
<br />® N0 59350
<br />, e a
<br />STATE Ovx\\�
<br />®S®® as �
<br />�1f 611 I �e�
<br />10\08\1 7
<br />NATHANIEL J. HATCHER. FL PE #59350
<br />IN
<br />I
<br />IL
<br />Iv
<br />I
<br />I
<br />I
<br />IF
<br />REV. DESCRIPTION DATE ll
<br />............. .......... E
<br />BID & PERMIT SET
<br />09.29.17
<br />CURRENT ISSUE STATUS:
<br />PROJECT NORTH
<br />ID
<br />®®
<br />WBRCM ■C
<br />ARCHITECTS ENGINEERS
<br />8130 Lakewood Main Street Phone: 941-556-0757
<br />Suite 210 Fax: 941-556-0759
<br />Lakewood Ranch, FL 34202 www.wbrcae.com
<br />_.._........_Firm Lic_AA26001395 & 27389 __Oou�s W.Whitney _1IA__...
<br />BEALLS OUTLET #542
<br />ZE P HYRH I LLS
<br />PROJECT: 6030 Gall Blvd, Zephyrhills, FL 33542 B
<br />FIRE ALARM NOTES &
<br />SPECIFICATIONS
<br />SHEET TITLE:
<br />........._._.......-- ------ ..............._-.................... _......._...... - ---- -- .............---............
<br />WBRCCAD FILE : T:\03Projets-Florida\3501-3600\3542M5BeallsOutletZephyrhillsFL\2Deslgn\Dwgs\Bldg\3542M5
<br />BEALLS OUTLET ZEPHYRHILLS It
<br />PROJECT No 3542XX� GRAPHIC SCALE:
<br />-t{.._.._._.- ........ _ pl'
<br />PROJECT MANAGER: Approver I SHEET No.
<br />__....--- .......................__------
<br />DRAWN BY: AJC FA 101
<br />CHECKED BY: NJH
<br />' a n
<br />
|