|
r
<br />HVAC GENERAL NOTES
<br />NO EXCLUSIONS FROM OR LIMITATIONS IN THE LANGUAGE USED IN THE CONTRACT
<br />DOCUMENTS SHALL BE INTERPRETED AS MEANING THAT THE EQUIPMENT, APPURTENANCES,
<br />AND/OR ACCESSORIES NECESSARY FOR A COMPLETE AND OPERATIONAL SYSTEM ARE NOT
<br />TO BE PROVIDED AS REQUIRED. THE SEPARATE DIVISIONAL CONTRACT DOCUMENTS DO NOT
<br />RELIEVE THE CONTRACTOR FROM THE RESPONSIBILITY TO PROVIDE THE WORK WHICH IS
<br />INDICATED ON ANY OF THE DIVISIONAL CONTRACT DOCUMENTS. REVIEW AND COORDINATE
<br />THE SCOPE OF WORK WITH ALL DOCUMENTS AND TRADES TO ASSURE A COMPLETE AND
<br />FUNCTIONAL SYSTEM IS BID AND INSTALLED.
<br />THE CONTRACTOR SHALL OBTAIN AND PAY FOR ALL PERMITS, FEES, AND INSPECTIONS
<br />REQUIRED TO COMMENCE AND COMPLETE HVAC WORK.
<br />SUBMIT FULL SUBMITTALS OF ALL HVAC EQUIPMENT AND MATERIALS TO THE ENGINEER FOR
<br />REVIEW, WHETHER IT IS EXACTLY AS SPECIFIED OR NOT.
<br />THE CONTRACT DOCUMENTS AND SUBMITTALS OF ALL TRADES SHALL BE COORDINATED AND
<br />BE VIEWED IN CONNECTION AND CONJUNCTION WITH EACH OTHER TO INSURE THE PROPER
<br />LOCATION AND INSTALLATION OF ALL DEVICES AND EQUIPMENT. MAKE PARTICULAR NOTE
<br />OF LOCATIONS AND DIMENSIONS SHOWN ON THE ARCHITECTURAL FLOOR PLANS AND
<br />ELEVATIONS.
<br />HVAC DRAWINGS INDICATE THE SCHEMATIC LAYOUT AND LOCATION OF THE HVAC SYSTEM
<br />COMPONENTS. UNLESS SPECIFIC DIMENSIONS ARE NOTED, THE ACTUAL LOCATION OF THESE
<br />COMPONENTS SHALL BE DETERMINED IN THE FIELD BY THE CONTRACTOR IN COORDINATION
<br />WITH THE WORK OF OTHER TRADES, THE USE OF MANUFACTURER'S SUBMITTALS, AND
<br />SIMILAR CERTIFIED .DATA.
<br />ALL HVAC EQUIPMENT INSTALLED OUTDOORS SHALL BE SECURED TO ITS SUPPORT AS
<br />DETAILED BY THE STRUCTURAL ENGINEER FOR THE REQUIRED WIND LOAD DESIGN.
<br />ALL EXTERIOR EXPOSED MATERIALS SHALL BE CONSTRUCTED OF NON-FERROUS MATERIALS
<br />AND BE PAINTED WITH TWO COATS OF RUST INHIBITOR PAINT.
<br />INSTALL AND TEST ALL EQUIPMENT AND MATERIALS IN ACCORDANCE WITH THE
<br />MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS. MAINTAIN ADEQUATE SERVICE
<br />SPACE AS REQUIRED. SERVICE SPACE SHALL BE CLEAR OF DUCTS, PIPES, CONDUITS, WALL
<br />STUDS, CEILING HANGERS, AND ANY OTHER CONSTRUCTION APPURTENANCE.
<br />CONTRACTOR SHALL COORDINATE AND PROVIDE ALL CEILING/FLOOR/WALL ACCESS PANELS
<br />THAT MAY BE REQUIRED FOR THE INSTALLATION, INSPECTION, AND SERVICE OF HVAC
<br />EQUIPMENT WHETHER OR NOT IT IS SHOWN. ACCESS PANELS TO BE SELECTED BY THE
<br />ARCHITECT.
<br />ALL WALL MOUNTED THERMOSTATS AND SIMILAR SENSORS SHALL BE INSTALLED AT A
<br />CENTER LINE ELEVATION OF 4'-0" ABOVE FINISHED FLOOR UNLESS OTHERWISE NOTED ON
<br />DRAWINGS. LOCATION OF THE SENSORS SHALL BE COORDINATED WITH THE OTHER TRADES
<br />FOR A NEAT APPEARANCE. FINAL LOCATION OF .THE SENSORS SHALL BE SUBJECT TO THE
<br />APPROVAL OF THE ENGINEER.
<br />PERFORM FINAL TESTING AND BALANCING OF ALL HVAC SYSTEMS IN ACCORDANCE WITH
<br />AABC OR NEBB STANDARDS. RECORD ALL DATA ON STANDARD "AABC" OR OTHER
<br />APPROVED FORMS, AND SUBMIT TO THE ENGINEER FOR REVIEW.
<br />AT PROJECT COMPLETION, THE CONTRACTOR SHALL PROVIDE A MINIMUM OF 2 HOURS OF
<br />TRAINING ON THE OPERATION AND MAINTENANCE OF THE HVAC EQUIPMENT.
<br />CONTRACTOR SHALL PROVIDE A ONE YEAR WARRANTY ON PARTS AND LABOR FROM THE
<br />DATE OF SUBSTANTIAL COMPLETION.
<br />EXHAUST AIR DUCTWORK SHALL BE GALVANIZED SHEET METAL. SEAL ALL DUCT JOINTS
<br />WITH HARDCAST.
<br />ALL DUCTWORK SHALL BE FABRICATED AND INSTALLED IN ACCORDANCE WITH THE LATEST
<br />EDITION rr OF SMACNA" DUCT CONSTRUCTION STANDARDS. FABRICATE DUCTWORK TO THE 2"
<br />W.G. PRESSURE CLASS AND SEAL TO SEAL CLASS C.
<br />DUCTWORKr r AIR DEVICES AND OTHER ITEMS OF THE AIR DISTRIBUTION SYSTEM SHALL BE
<br />SUPPORTED DIRECTLY FROM THE BUILDING STRUCTURE AND NOT FROM THE CEILING OR
<br />P
<br />CEILING SUSPENSION SYSTEM. AIR DEVICES SHALL BE SUPPORTED FROM THE BUILDING
<br />STRUCTURE FROM AT LEAST TWO POINTS. COORDINATE LOCATION OF AIR DEVICES WITH
<br />ALL OTHER TRADES.
<br />100
<br />X4X2
<br />i
<br />Aitor QC
<br />0 �S �.
<br />M
<br />EAD1
<br />100 O
<br />8X8
<br />DG1
<br />EAD1
<br />Q2 200
<br />8X8
<br />3 � E
<br />1
<br />I �
<br />3
<br />Mwo
<br />i1�
<br />24X2E
<br />3 ..
<br />_
<br />9 ...€
<br />�.,
<br />155 SF
<br />_F_..... ;... 6 S
<br />r'
<br />1
<br />.... .........<.,.... „.. «,,,, i �,,...
<br />V
<br />� � EAD1
<br />1200
<br />8X8
<br />._ ._ _._ .._.__._.... .. ......
<br />I � I
<br />Arbor Mafir� Entry Arbor
<br />I � i
<br />I
<br />g i E I O; I I}j `
<br />t ....._,I �.._._.
<br />s
<br />f
<br />a
<br />HVAC SYMBOL _LEGEND
<br />SYMBOL
<br />DESCRIPTION
<br />2
<br />ROUND DUCTWORK SIZE, WHERE THE DIMENSION IS THE INSIDE
<br />PLAN VIEW DUCTWORK DIMENSION
<br />z
<br />EXHAUST AIR CEILING AIR DEVICE
<br />—DG->
<br />DOOR GRILLE AIR DEVICE FOR TRANSFER OF AIR, ARROW
<br />INDICATES AIRFLOW DIRECTION
<br />TAG
<br />SUPPLY, RETURN, TRANSFER, OUTSIDE, AND EXHAUST AIR DEVICE
<br />SAW AIRFLOW
<br />IDENTIFICATION
<br />150 --- CFM
<br />80
<br />SAD=SUPPLY AIR DEVICE, RAD=RETURN AIR DEVICE,
<br />TAD=TRANSFER AIR DEVICE, EAD=EXHAUST AIR DEVICE,
<br />f
<br />OAD=OUTSIDE AIR DEVICE
<br />NECK SIZE
<br />TAG
<br />1
<br />DG1 AIRFLOW
<br />150 --- CFM
<br />DOOR GRILLE AIR DEVICE IDENTIFICATION
<br />202
<br />DOOR GRILLE SIZE,
<br />(LENGTHXHEIGHT)
<br />❑T
<br />TEMPERATURE SENSOR
<br />OS
<br />SWITCH
<br />FAN SCHEDULE
<br />I
<br />FAN TAG
<br />-
<br />EF-T
<br />EF-2
<br />EF-3 EF-4
<br />SERVICE TYPE
<br />-
<br />EXHAUST AIR
<br />EXHAUST AIR
<br />EXHAUST AIR EXHAUST AIR
<br />AIR FLOW
<br />CFM:
<br />1OG
<br />200
<br />200 100
<br />EXTERNAL STATIC PRESSURE
<br />IN WG
<br />0.5
<br />0.5
<br />0.5, 0.5
<br />FAN TYPE
<br />-
<br />CEILING
<br />CEILING
<br />CEILING CEILING-
<br />DRIVE TYPE
<br />-
<br />DIRECT
<br />DIRECT
<br />DIRECT DIRECT
<br />MOTOR
<br />HP/BHP
<br />66.9 WATTS
<br />66.9 WATTS
<br />66.9 WATTS 66.9 WATTS
<br />SPEED
<br />RPM
<br />1014,
<br />1014
<br />1014 1014
<br />SOUND
<br />SONES
<br />2,5
<br />2,5
<br />2.5 2.5
<br />VOLTAGE
<br />VIPHIHZ
<br />12011160
<br />12011160
<br />12011/60' 120/1160
<br />WEIGHT
<br />LBS
<br />16
<br />16
<br />16 16
<br />MANUFACTURER
<br />-
<br />COOK
<br />COOK
<br />COOK COOK
<br />MODEL
<br />GC488
<br />GC-188
<br />GC-18NOTES
<br />-
<br />1,2,5,6,7
<br />1,2,4,6,7�EG,C-188
<br />2,4,6,7 1,2,3,6,7
<br />NOTES .._..
<br />1. PROVIDE DISGONNECT. ....................... ... ..... ...... .• ...... ,..... .. _ _.. .
<br />2. PROVIDE SOLID STATE SPEED CONTROLLER. ...... ........ ..
<br />3. WALL SWITCH PRUVIDED By ELECTRICAL CONTRACTOR_
<br />4 INTERLOC WITH LIGHTS AND EN MINUTE DELAYS SWITCH PROVIDED ED BY
<br />ELECTRICAL CONTRACTOR. I
<br />5. PROVIDE LINE VOLTAGE THERMOSTAT.
<br />6 ITEE O PRVIDW A U U
<br />.. _-: _.._::. �._ L MANM GRILLE
<br />.. _ _ .............. ...M..... ..
<br />F. PROVIDE' BACKDRAFT DAMPER.
<br />100 ,
<br />24X24F,
<br />Eqs.'
<br />CyEE—
<br />i
<br />EAD1
<br />O100
<br />8X8
<br />HVAC FLOOR PLAN
<br />SCALE: 3/16"40"
<br />HVAC. CODE CRITERIA
<br />THE FOLLOWING IS A LIST OF ALL CODES ADOPTED DECEMBER 31, 2017 BY THE STATE FIRE
<br />MARSHALL'S RULE 69A3.012 F.A.C.:
<br />* FLORIDA BUILDING CODE 6TH EDITION (2017) - ALL SECTIONS
<br />* FLORIDA ENERGY EFFICIENCY CODE (FBC 2017), FLORIDA ENERGY CODE SOFTWARE:
<br />ENERGYGAUGE USA VERSION 6.00
<br />* FLORIDA FIRE PREVENTION CODE 6TH EDITION (2017)
<br />69A-3.012 STANDARDS OF THE NATIONAL FIRE PROTECTION ASSOCIATION ADOPTED.
<br />(1) EXCEPT AS SPECIFICALLY MODIFIED BY STATUTE OR BY THE STATE FIRE MARSHAL'S
<br />RULES, THE "FLORIDA FIRE PREVENTION CODE, 6TH EDITION (2017)," WHICH IS COMPRISED
<br />OF THE FLORIDA SPECIFIC EDITION OF NFPA 101, THE LIFE SAFETY CODE (2015 EDITION)
<br />AND THE FLORIDA SPECIFIC EDITION OF NFPA 1, THE FIRE CODE (2015 EDITION), ARE
<br />HEREBY ADOPTED AND INCORPORATED BY REFERENCE AND ARE APPLICABLE TO THOSE
<br />BUILDINGS AND STRUCTURES SPECIFIED IN PARAGRAPHS (A) AND (B) OF SUBSECTION (1)
<br />OF SECTION 633.206, F.S. IN ADDITION, THE FOLLOWING STANDARDS, EXCEPT AS
<br />SPECIFICALLY MODIFIED IN THE RULE CHAPTERS IN RULE TITLE 69A, ARE HEREBY ADOPTED
<br />AND INCORPORATED BY REFERENCE AND SHALL TAKE EFFECT ON THE EFFECTIVE DATE OF
<br />THIS RULE, AS A PART OF THE UNIFORM FIRE SAFETY STANDARDS ADOPTED BY RULE BY
<br />THE STATE FIRE MARSHAL AND ARE APPLICABLE TO THOSE BUILDINGS AND STRUCTURES
<br />SPECIFIED IN PARAGRAPHS (A) AND (B) OF SUBSECTION (1) OF SECTION 633.206, F.S.:
<br />* NFPA 70, 2014 EDITION, NATIONAL ELECTRIC CODE
<br />* NFPA 90A, 2015 EDITION, STANDARD FOR THE INSTALLATION OF AIR-CONDITIONING
<br />AND VENTILATING SYSTEMS
<br />• NFPA 90B, 2015 EDITION, STANDARD FOR THE INSTALLATION OF WARM AIR HEATING
<br />AND AIR-CONDITONING SYSTEMS
<br />AMERICAN SOCIETY OF HEATING, REFRIGERATION AND AIR CONDITIONING ENGINEERS, INC.
<br />(ASHRAE) (INCLUDING ALL APPROVED ADDENDUM):
<br />ASHRAE FUNDAMENTALS 2017
<br />ASHRAE GUIDELINE 4-2008, PREPARATION OF OPERATING AND MAINTENANCE
<br />DOCUMENTATION FOR BUILDING SYSTEMS
<br />* ASHRAE STANDARD 111-2008, MEASUREMENT, TESTING, ADJUSTING AND BALANCING OF
<br />BUILDING HEATING, VENTILATION AND AIR-CONDITIONING SYSTEMS
<br />SHEET METAL AND AIR CONDITIONING' CONTRACTORS' NATIONAL ASSOCIATION (SMACNA)
<br />(INCLUDING ALL APPROVED ADDENDUM):
<br />HVAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE, 3RD EDITION, 2005
<br />HVAC SYSTEM DUCT DESIGN, 4TH EDITION, 2006
<br />OTHER:
<br />* LOCAL CODES AND ORDINANCES
<br />NOTE: TO THE BEST OF THE ENGINEER'S KNOWLEDGE, THESE HVAC DESIGN DRAWINGS
<br />COMPLY WITH THE ABOVE CODE CRITERIA. WHEN TWO OR MORE CODES OR
<br />STANDARDS ARE IN CONFLICT, THE MORE STRINGENT SHALL APPLY.
<br />EMERALD
<br />ENGINEERING INC.
<br />9942 CURRIE DAVIS DR. STE H., TAMPA, FL 33619
<br />TEL (813) 995-0300 FLORIDA E8# 0027845
<br />WWW.EMERALDMEP.COM EEI PROJECT# 180822
<br />Right Wing
<br />Pavilion .
<br />£ U
<br />81 `u,
<br />0 CODED NOTES
<br />1) REFER TO DETAIL ON THIS SHEET FOR CEILING MOUNTED
<br />EXHAUST FAN.
<br />2) MOUNT EXHAUST GRILLE IN ROOF OVERHANG SOFFIT.
<br />CEILING
<br />EXHAUST FAN
<br />ATTACH TO
<br />BUILDING STRUCTURE.
<br />PROVIDE A
<br />MINIMUM OF FOUR
<br />ANGLES OR
<br />FACTORY
<br />7r
<br />MOUNTING
<br />BRACKET(S) FOR
<br />HANGING ROD
<br />1/4" THREADED ROD. ATTA(WMFMT
<br />VERIFY WITH FAN
<br />MANUFACTURER
<br />FOR FAN WEIGHT.
<br />FOR FANS UNDER
<br />160 LBS.
<br />PROVIDE ISOLATOR
<br />BUSHINGS AT
<br />ROD/FAN
<br />INTERFACE.
<br />PROVIDE DUCT
<br />TRANSITION AS
<br />REQUIRED.
<br />EXHAUST
<br />DUCT.
<br />REFER TO
<br />HVAC FLOOR
<br />PLANS FOR
<br />SIZE. i
<br />AIRFLOW
<br />EXHAUST
<br />FAN
<br />FACTORY
<br />CEILING
<br />GRILLE.
<br />/<\ I
<br />CEILING
<br />NOTE:
<br />AIRFLOW FAN TO BE DIRECTLY SUPPORTED
<br />FROM BUILDING STRUCTURE ABOVE
<br />AND NOT FROM CEILING.
<br />AIR DEVICE TAG
<br />EADi
<br />DG1
<br />SERVICE TYPE
<br />EXHAUST AIR
<br />TRANSFER AIR
<br />DESCRIPTION
<br />LOUVERED GRILLE
<br />(MINUS FILTER)
<br />LOUVERED
<br />DOOR GRILLE
<br />NECK
<br />RECTANGULAR
<br />RECTANGULAR
<br />AIR FLOW PATTERN
<br />1-WAY
<br />1-WAY'
<br />BLADESIVANES
<br />FIXED
<br />FIXED
<br />MATERIAL
<br />ALUMINUM
<br />ALUMINUM
<br />FINISH
<br />WHITE
<br />WHITE
<br />DAMPER
<br />OPPOSED BLADE
<br />NONE
<br />MANUFACTURER'
<br />PRICE
<br />PRICE
<br />MODEL
<br />63OFF
<br />ATGH
<br />NOTES
<br />1,2,3;4
<br />1,34
<br />NOTES
<br />1; PROVIDE FRAMES/FLANGES AS RE 01k _..._
<br />Q ED FO R
<br />CONSTRUCTION AND AS SELECTED BY ARCHITECT.
<br />2. FACE OF AIR DEVICE TO BE HINGED AND CAPABLE TO FLIP
<br />DOWN FOR INT RN E AL CLEANING. N.
<br />3 COLOR TO BE SELECTED BY HI ARCTECT,
<br />4. PROVIDE REMOVABLE INSECT SCREEN.
<br />0 8 436 ®s
<br />0
<br />� •® E tip m° �C!
<br />MICHAEL A CO`STELLO, PE
<br />FL. REG. NO. PE81436
<br />U)
<br />Z
<br />O
<br />U^)
<br />Lu
<br />cc
<br />0
<br />■
<br />m
<br />cc
<br />N
<br />Cz
<br />Cl)
<br />0-
<br />a�
<br />Mid
<br />C/)
<br />CIO
<br />>
<br />MIMI
<br />0
<br />-0
<br />CZ
<br />-0
<br />Lm
<br />o
<br />J
<br />4)
<br />Q
<br />Q
<br />N
<br />N
<br />N
<br />BSB
<br />iN
<br />www.bsbdesign.com
<br />100 Main St. Suite 209
<br />Safety Harbor, Florida 34695
<br />8132654808
<br />JOB NO: AM180320.00 PROJ MGR: MC
<br />DRAWN: CQ CHECKED: MC
<br />HVAC FLOOR PLAN
<br />
|