38023 Medical Center Ave - Laserfiche WebLink

Browse Search

NOTE5 P 1. ALL WORK SHALL BE IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND SHALL AL50 COMPLY WITH ALL APPLICABLE RULES AND R REGULATIONS OF LOCAL AND STATE LAWS AND ORDINANCES. 0 2. ALL CONDUGTOR5 SHALL BE STRANDED COPPER, CONDUCTOR J INSULATION SHALL BE TYPE THHN THERMOPLASTIC 600 VOLT OR EQUAL U.O.N. E 3. THE INTERIOR ELECTRICAL SYSTEMS SHALL BE COMPLETELY AND EFFECTIVELY GROUNDED AS REQUIRED BY THE NEC. ALL METALLIC, G RACEWAYS SHALL BE MECHANICALLY AND ELECTRICALLY SECURE AT ALL JOINTS AND AT ALL BOXES, CABINETS, FITTINGS AND EQUIPMENT. T METALLIC, RACEWAY5 SHALL BE CONNECTED TO A DIRECT GROUND AT THE POINT OF ELECTRICAL SERVICE ENTRANCE. 4. UPON COMPLETION OF WORK CORRECT ALL PANELBOARO CIRCUIT DIRECTORY CARDS TO REFLECT A5-BUILT CONDITIONS. A SET OF A5-BUILT DRAWIN655 SHALL AL50 BE PREPARED AND TURNED OVER TO THE ARCHITECT. 5. ALL RACEWAYS SHALL BE PROVIDED WITH EQUIPMENT GROUND CONDUCTOR. 6. CONTRACTOR SHALL FIELD VERIFY RECEPTACLE CONFIGURATION, VOLTAGE, PHASE AND AMPERAGE FOR ALL REQUIRED OUTLETS. PROVIDE DEDICATED CIRCUITS AS REQUIRED. ADV15E ENGINEER IF NECESSARY. -1. CONTRACTOR SHALL SUPPLY AND INSTALL ALL JUNCTION BOXES, TROU6HS, WIRE, CIRCUIT BREAKERS, WIRE, ETC., UNLESS OTHERWISE SPECIFIED. 8. CONDUIT RUNS ARE SHOWN SCHEMATICALLY. BUILDING CONDITIONS TO DETERMINE THE ACTUAL RUNS. 4. CONDUIT ELBOWS TO BE LARGE SWEEPS PER NEC, 346-10. 10. CONTRACTOR SHALL PROVIDE AND COIL A MINIMUM 10'-0 INCH OF SLACK CONDUCTOR FOR CONNECTION TO EQUIPMENT BY OTHERS. IDENTIFY BOTH ENDS OF WIRE. 11. CONTRACTOR SHALL OBTAIN A COPY OF THE BrainLAB INSTALLATION AND 51TINO DRAWING5 PRIOR TO START OF CONSTRUCTION AND COMPLY ACCORDINGLY. 12. ALL TELEPHONE/DATA JACKS AND COMMUNICATION CABLING TO BE PROVIDED AND INSTALLED BY OTHERS. ELECTRICAL CONTRACTOR TO PROVIDE AND INSTALL ALL ASSOCIATED OUTLET BOXES AND CONDUITS. 13. CONDUITS AND DUCT, ABOVE CEILING OR BELOW FINISHED FLOOR, MUST BE INSTALLED PER BrainLAB DRAWINGS TO REDUCE RUN LENGTH. 14. THESE DRAWINGS ARE DIAGRAMMATIC AND INTENDED ONLY TO SHOW THE SCOPE OF WORK TO BE DONE. THE ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE TO FIELD VERIFY THE SUITABILITY OF LOCATING ALL NEW CONDUIT SHOWN ON THE PLANS OR IDENTIFIED IN THE NOTES. CONTRACTOR NOTICE I. THESE ELECTRICAL DRAWINGS HAVE BEEN DESIGNED WITH AND SHALL BE BID IN CONJUNCTION WITH THE BratnLAB INSTALLATION AND SITING DRAWING SET. SUBMISSION OF AN ELECTRICAL BID WILL BE CONSIDERED AS EVIDENCE THAT THE BrainLAB DRAWINGS WERE REVIEWED AND THAT ALL INFORMATION SHOWN HAS BEEN INCLUDED IN THE BID. LATER CLAIMS FOR ADDITIONAL COMPENSATION FOR WORK DESCRIBED ON EITHER SET OF DRAWING-5 SHALL NOT BE ACCEPTED. CONTRACTOR SHALL REVIEW G.E. DRAWINGS FOR REQUIRED USE OF ALUMINUM CONDUIT IN SPECIFIC LOCATIONS. 2. ELECTRICAL DRA"IN65 INDICATE THE INSTALLATION CONCEPT FOR THE BratnLAB EQUIPMENT. HOWEVER, CONTRACTOR SHALL OBTAIN AND BID EQUIPMENT INSTALLATION WITH BrainLAB INSTALLATION AND 51TIN6 DRAWIN65 WHICH INDICATE ADDITIONAL REQUIREMENT5 NECESSARY FOR PROPER INSTALLATION. ALL DEVICES, EQUIPMENT, APPARATUS, ETC'. USED WITHIN THE ROOM MUST BE APPROVED BY THE BrainLAB PROJECT MANAGER PRIOR TO INSTALLATION. 3. CONTRACTOR SHALL REFER TO INTERIOR ARCHITECTURAL DRAWINGS FOR EXACT MOUNTING HEIGHTS AND/OR LOCATIONS OF ALL OUTLETS AND WIRING DEVICES. NOTE5 K O CONTROL ROOM POWER BOX, FURNISHED WITH BraInLAB EQUIPMENT, INSTALLED BELOW COUNTER BY ELECTRICAL CONTRACTOR. Y X-RAY TUBE FLOOR BOX, FURNISHED WITH BrafnLAB EQUIPMENT, INSTALLED BY GENERAL CONTRACTOR. �3 PROVIDE 2+00MPARTMENt 10 x3-1/2 HORIZONTAL SURFACE WALL DUCT AT 12" A.F.F. TO TOP. VERIFY REQUIRED LENGTH, PROVIDE ALL NECESSARY FITTIN65 AND SUPPORTS. PROVIDE 6ROMMETED OPENINC75 AS DIRECTED BY EQUIPMENT SUPPLIER/INSTALLER. �4 IN -ROOM POWER BOX, FURNISHED WITH BratnLAB EQUIPMENT, INSTALLED ABOVE CEILING BY ELECTRICAL CONTRACTOR. PROVIDE ALL NECESSARY SUPPORTS. (1) 4" CONDUIT FROM XRAY TUBE FLOOR BOX, RUN BELOW SLAB, AND TURNED UP BELOW HORIZONTAL WALL DUCT. U6 VERIFY FOR REQUIRED TRANSITION FROM CONDUIT TO WALL DUCT AND PROVIDE ACCORDINGLY. O PROVIDE I" CONDUIT ("IRE) FROM EXISTING WARNING LIGHT BACK TO COMPUTER CABINET. MAKE ALL REQUIRED TERMINATIONS. ® PROVIDE A 100 AMP, 3-POLE, NON -FUSED DISCONNECT SWITCH FOR CONNECTION TO X-RAY GENERATOR. MAKE ALL REQUIRED TERMINATIONS. ® (1) 3" CONDUIT (EMPTY W/PULLWIRE) FROM GENERATOR CABINET TO CONTROL ROOM. VERIFY TERMINATIONS AT EACH END PRIOR TO ROUGH -IN AND PROVIDE ACCORDINGLY. 10 (1) 2" CONDUIT (EMPTY W/PULLWIRE) FROM COMPUTER CABINET TO CONTROL ROOM POWER BOX. II GANTRY COUGH MOUNTED INTERFACE ELECTRONIC, (BY OTHERS). 12 (1) 2" CONDUIT (EMPTY W/PULLWIRE) FROM IN -ROOM POWER BOX TO CEILING WORKSPACE. VERIFY TERMINATIONS. 13 (1) 1" CONDUIT (EMPTY W/PULLWIRE) FROM IN -ROOM POWER BOX TO FLAT PANEL DETECTORS. VERIFY TERMINATIONS. 14 (1) 1" CONDUIT (EMPTY W/PULLWIRE) FROM IN -ROOM POWER BOX TO CAMERA SYSTEM. VERIFY TERMINATIONS. 15 (1) 3 CONDUIT (EMPTY W/PULLWIRE) FROM COMPUTER CABINET TO IN -ROOM POWER BOX. I6 PROVIDE A 30 AMP, I -POLE, NON -FUSED D15CONNEGT SWITCH FOR CONNECTION TO COMPUTER CABINET. MAKE ALL REQUIRED TERMINATIONS. 17 (1) 2 CONDUIT (EMPTY W/PULLWIRE) FROM COMPUTER CABINET TO GANTRY INTERFACE. 18 (1) 2" CONDUIT (EMPTY W/PULLWIRE) FROM COMPUTER CABINET TO CAMERA SYSTEM ABOVE CEILING. Iq (1) 3" CONDUIT (EMPTY W/PULLWIRE) FROM COMPUTER CABINET TO FLAT PANEL DETECTORS ABOVE CEILING. COORDINATE WITH EQUIPMENT SUPPLIEPANSTALLER FOR CONDUIT TERMINATION REQUIREMENTS AT THE COMPUTER CABINET AND COMPLY ACCORDINGLY. 21 EXISTING EMERGENCY -OFF PUSHBUTTON FOR ACCELERATOR. CONTRACTOR SHALL USE SAME DEVICE TO ACTIVATE THE SHUNT - TRIP FOR BrainLAB MAIN BREAKER IN PANEL 'A', FOR SIMULTANE SHUT DOWN OF EQUIPMENT. 5Y5-rr=M &ROUND I NC NOTE5 THE PROPOSED BrainLAB SYSTEM REQUIRES CONNECTION TO GROUND AT A SINGLE POINT. TH15 POINT WILL BE ON THE WALL A5 A MAIN GROUND BUS BAR AND 15 THE POTENTIAL EQUALIZATION POINT. COORDINATE LOCATION OF POTENTIAL EQUALIZATION MAIN BUS BAR WITH EQUIPMENT SUPPLIER / INSTALLER. I. ALL METAL DEVICES, INCLUDING METAL SURFACES OF FIXED MEDICAL EQUIPMENT, WITHIN THE TREATMENT ROOM SHALL BE BONDED TO THE POTENTIAL EQUALIZATION GROUND BUS BAR AS INDICATED BELOW. ITEMS SHALL INCLUDE, BUT NOT LIMITED TO: a. X-RAY GENERATOR TO MAIN PEG BU5 BAR. b. BOTH FLOOR BOXES TO X-RAY GENERATOR PEG BUS BAR. c. BOTH FLAT PANEL -CEILING MOUNTS TO IN -ROOM DISTRIBUTION BOX PEG BUS BAR. d. CAMERA CEILING MOUNT TO IN -ROOM DISTRIBUTION BOX PEG BUS BAR. a. TOUGH 5GREEN CEILING FRAME TO IN -ROOM DISTRIBUTION BOX PEG BU5 BAR. F. IN -ROOM DISTRIBUTION BOX PEG BUS BAR TO MAIN PEG BU5 BAR. g. IN -ROOM DISTRIBUTION BOX PEG BUS BAR TO COMPUTER CABINET PEG BU5 BAR. h. COMPUTER CABINET PEG BUS BAR TO MAIN PEG BUS BAR. i. CONTROL ROOM DISTRIBUTION BOX TO COMPUTER CABINET PEG BUS BAR. BOTH FLOOR BOXES TO MAIN PEQ BU5 BAR. MAIN PEQ BUS BAR TO PATIENT COUGH, TABLE, LINAG FRAME. 2. VERIFY WITH EQUIPMENT SUPPLIER/I145TALLER FOR ALL REQUIRED GROUNDING LOCATIONS AND PROVIDE ACCORDINGLY. 3. DEDICATED EARTH CONDUCTOR (GROUND) SHALL BE SAME 51ZE AS POWER WIRE5 AT ALL TIMES FOR ALL ROUTINGS FROM GROUNDED NEUTRAL SOURCE TO BrainLAB EQUIPMENT. 4. CONTRACTOR SHALL REFER TO 'ELECTRICAL SAFETY / EQUIPOTENTIAL GROUNDING' SECTION 3.4 OF THE 51TE PREPARATION MANUAL FOR ALL REQUIRED TERMINATIONS AND PROVIDE ACCORDINGLY. PEQ = POTENTIAL EQUALIZATION BUS BAR. GENERAL NOTE: EQUIPMENT LAYOUT AND NOTES ARE BASED UPON GENERAL INFORMATION GIVEN TO THE ENGINEER AT TIME OF DESIGN. THE GENERAL CONTRACTOR SHALL COORDINATE ALL CONDUIT REQUIREMENTS, ALL CABLING LENGTHS AND EQUIPMENT LAYOUT OF ACTUAL EQUIPMENT FURNISHED WITH BrainLAB AUTHORIZED REPRESENTATIVE PRIOR TO CONSTRUCTION. ELECTRICAL CONTRACTOR SHALL COORDINATE CLOSELY WITH BrainLAB REPRESENTATIVE FOR CLARIFICATION OF GABLES AND EQUIPMENT TO BE: a) SUPPLIED/INSTALLED BY BrainLAB b) SUPPLIED/INSTALLED BY CONTRACTOR c) SUPPLIED BY BrainLAB / INSTALLED BY CONTRACTOR d) AVAILABLE THROUGH BrainLAB / INSTALLED BY CONTRACTOR CRITICAL NOTE CONTRACTOR MUST COORDINATE THESE ELECTRICAL DRAWINGS WITH BrainLAB INSTALLATION DRAWING-5 FOR REFERENCE TO ADDITIONAL ELECTRICAL DETAILS AND NOTES AND PROVIDE ACCORDINGLY. CHEHAYEB & ASSOCIATES, INC. CONSULTING PROFESSIONAL ENGINEERS cTs 3702 AZEELE ST. (813) 876-1415 ` TAMPA, FL 33609 (fax) 876-0913 LIC. #49521 SOUHEIL CHEHAYEB CERT. #7340 08-127 BrainLAB COMPUTER CABINET A -I ��POWER AND CONDUIT PLAN, SCALE: 1/4" = 1'-0" CONDUIT AND WIRE SYSTEMS WITHIN TH15 ROOM SHALL COMPLY WITH REQUIREMENTS FOR REDUNDANT GROUNDING PER N.E.G. ARTICLE 4i I REVISIONS I No. I Date Description MIN u N cq W N o o' 00 U 0O C*l zN z Q N M d00 H 00 Oro O • . u in p W a a Issued for: Dater ❑ PRELIMINARY ❑ PRICING ❑ BIDDING ■ PERMIT i0-oi-oa ❑ CONSTRUCTION R EIL PHAYEB, P.E. LIC NIP. 49521 55 i -- I Drawn by: P.M. Checked by: S.C. J