Laserfiche WebLink
d <br />COLUMN CON5TRUC' <br />STUCCO <br />(CEMENT PLASTER) <br />2 LAYER5 WRB --� <br />WEEP 5CREED <br />CONCRETE 5TOOP . o <br />1 COLUMN AT CONCRETE SLAB <br />SCALE: N.T.S. <br />BARRIER <br />FLA5NING <br />NAILING FI <br />NO 5EALA <br />MAKE SURE THE SHEATHING WRAP LAPS OVER THE TOP <br />FIN. LEAVE A I/4" GAP BETWEEN THE EXTERIOR FINISH <br />AND THE FLANGE, BUT DON'T CAULK THIS GAP. WATER <br />DRAINING FROM ABOVE MUST HAVE A PLACE TO EXIT. <br />SILL <br />6 FIN WINDOW HEAD DETAIL <br />SCALE: N.T.5. <br />CORNER BEAD FASTENED WITH <br />NAIL5, 5CREW5, OR 5TAPLE5 AT <br />5TUCCc <br />OUTSIDE CORNER <br />INSIDE CORNER <br />NOTE: <br />2 STUCCO DETAIL AT CORNERS <br />SCALE: N.T.5. <br />BEAD OF 51LICON <br />CAULK UNDER <br />WINDOW FLANGE <br />5EALANT <br />BITUMINOU5 <br />MEMBRANE OR FELT <br />STUCCO BAND <br />EXTERIOR FIN15H <br />DETAIL <br />7 FIN WINDOWS EXT. CASINGS <br />SCALE: N.T.5. <br />HEADER DETAIL <br />BACK CAULK 51LL DAM <br />AND 12" UP WALL EACH SIDE <br />STOP FLASHING HERE INTERIOR <br />PEEL-AND-5TICK <br />MEMBRANE <br />2 LAYERS <br />W.R.B. <br />SHEATHING <br />NOTES: <br />APPLY A NARROW DAM 5TRIP TO THE ROUGH 51LL BEFORE FLASHING WITH <br />5HEATHING WRAP OR A FLEXIBLE FLA5NING MEMBRANE <br />3 SILL FLASHING DETAILS <br />SCALE: N15. <br />EXTERIOR FIN15H <br />5TUCCO BAND <br />BITUMINOU5 <br />MEMBRANE OR FELT <br />STEP 1 <br />IN5TALL THE VENT ACCORDING TO THE <br />MANUFACTURER'5 RECOMMENDATION5. TRIM <br />THE HOU5E WRAP A CLOSE A5 POSSIBLE <br />AROUND THE PERIMETER OF THE VENT. <br />5ELF ADHE51VE <br />MEMBRANE FLA5NING <br />AT DOOR5 <br />BACK CAULK 51LL <br />AND 12" UP WALL <br />EACH SIDE <br />WOOD FRAME <br />4 FLASHING DOOR THRESHOLD <br />SCALE: N15. <br />STEP 2 <br />FLASH THE VENT U51NG THE SAME METHOD A5 WINDOW5. 5TARTING AT <br />THE BOTTOM FLANGE: CUT THE FLASHING 50 THAT IT EXTENDS PA5T <br />THE FLANGE5 BY I" ON BOTH 51DE5, NOW APPLY THE FLA5NING TO <br />THE 51DE5 OF THE VENT. REMEMBER TO EXTEND THE FLA5NING I" ON <br />BOTH TOP AND BOTTOM. MAKE SURE TO 5MOOTH OUT WRINKLE5 AND <br />AIR BUBBLE5. THE U5E OF A J-ROLLER 15 OPTIONAL. <br />PREFAB METAL EXTERIOR <br />DOOR THRE5HOLD DOOR <br />FORMED "SEAT" IN <br />CONCRETE SLAB ACT5 <br />A5 PAN FLA514ING — <br />- -mll <br />Z5LA5 ON GRADE USE <br />° °� PLASTIC <br />5HIM5 <br />CONCRETE SLAB UNDER <br />DooR <br />5 FLASHING DOOR THRESHOLD <br />SCALE: N.T.5. <br />NOTE: <br />THI5 TYPE OF IN5TALLATION 15 SUITABLE FOR 5EVERAL DIFFERENT PENETRATION5. ALWAY5 <br />USE THE 5HINGLING METHOD AND EN5URE A TIGHT 5EAL AROUND THE FLANGE/PENETRATION. <br />FRAME WALL FLASHING PENETRATIONS <br />SCALE: N.T.5. <br />STEP 3 <br />THE FINAL STEP 15 TO IN5TALL THE <br />FLA5NING ACROSS THE TOP. EXTEND THE <br />FLA5NING OUT AT LEAST I" ON BOTH 51DE5. <br />BEWS <br />DESIGN GROUP <br />150 STATE STREET EAST <br />OLDSMAR, FLORIDA 34677 <br />813. 925.1300 TEL <br />813.92,5.1800 FAX <br />W W W.DAVLSBEWS.COM <br />TAMPA • DENVER <br />� EST. 1994 � <br />O <br />Z O <br />N <br />0 <br />�-' O <br />> (n M O <br />O <br />fn <br />z C) -�-r <br />LL <br />c� <br />QU Q00 <br />z�� <br />w WO <br />J O <br />�O <br />d' <br />0z <br />�V) <br />�s <br />w� <br />zap <br />z� <br /><a <br />W< <br />'^ �z'u0 <br />-U <br />J <br />I--� = o W z <br />" o J i <br />�aO�n <br />a�aCo <br />U w N <br />W mow° <br />Q z z <br />}O <br />w <br />0 <br />o QQ <br />U o� <br />(Y o I.0 <br />�UJ <br />Q Q � W <br />z O 0 <br />Z <br />J z O <br />w z F— <br />O '—' <br />z a Lu <br />z _� <br />o a_ w �m <br />SCALE : AS NOTED <br />DATE : 10-19-2018 <br />VERSION NO. <br />imo <br />SHEET NO. <br />DT4 <br />DAVIS <br />