Laserfiche WebLink
Pentair 1 hbw <br />Pael and Spa, <br />Inteliff-i E5g <br />Underwater Pool <br />Color -Changing LED Light <br />Installation and User's Guide <br />IMPORTANT SAFETY INSTRUCTIONS <br />READ AND FOLLOW ALL INSTRUCTIONS <br />SAVE THESE INSTRUCTIONS <br />Pool Light Specifications 1 of 3 <br />Obtained from manufacturer - Pentair <br />a <br />1. Feed cord through conduit to Junction Box, leaving at least tour (4) <br />feet of cord at the tight fixture to coil around the light; see Figure 1, on <br />page 7. The four (4) feet of cord around the light allows the light to be <br />serviced after the pool is filled with water. <br />2. Cut the cord at the Junction Box, leaving at least six (6) inches of <br />cord to make connections. <br />3. Strip back six (6) inches of the outer cord jacket to expose the three <br />insulated wires (be careful not to damage the insulation on the three <br />(3) innerwires). <br />4. Connect all three (3) wires to the corresponding circuit wires in the <br />Junction Box and secure the Junction Box cover in place, <br />WENIf the light is not submerged in water and powered on for <br />more than 10 minutes, the light will switch off for a cooling down period of <br />10 minutes then power back on. This circuitry protects the light from being <br />potential damage. <br />6. Install the IntelliBrite light assembly into the niche <br />and tighten the special bronze pilot screw (see <br />Figure 1, on page 7. <br />Use only the special pilot screw <br />provided with this underwater light. This screw mounts <br />and electrically grounds the housing securely to the <br />mounting ring and wet niche. Failure to use the screw <br />provided could create an electrical hazard which could <br />result in death or serious injury to pool users, installers or <br />others due to electrical shock, <br />6. Fill the pool until the underwater light is completely submerged in <br />water before operating the light for more than ten (10) seconds. <br />7. Final check for proper light operation: To check for proper <br />operation, switch on the main switch or circuit breaker, and the switch <br />that operates the InteiliBrite underwater light itself. The light should <br />illuminate when power is applied. If not recheck the installation steps <br />starting with Step 1. <br />IntelliBrite' 5g PKKA LED Ligltt tn4lallation and user's Guide <br />Pool Light Specifications 2 of 3 <br />Obtained from manufacturer - Pentair <br />Pool Bonding Plan <br />Scale: Not to scale <br />To GFCI, C]IMW <br />Blre411V anti — <br />Power 8wrce. <br />Figure t. <br />RW --- <br />Ctlit <br />4' min. <br />#8 AWG Ground <br />Connecter bonding <br />is located at rear <br />of niche. <br />8" min. Junction Box or Low <br />Voltage Transformer, to the <br />max, water level of the pool, <br />min. to top of Lens. <br />Concrete must be cut <br />back around niche to <br />allow for a compacted <br />plaster seal. <br />l.._......_11.50' <br />1 <br />Call 4 ft d light <br />tale around fbdura <br />Pool Light Specifications 3 of 3 <br />Obtained from manufacturer - Pentair <br />v <br />#8 <br />WIF <br />NOTE: ALL METAL LOCATED WITHIN <br />5 FEET OF POOL WATER SHALL BE <br />BONDED. <br />NOTE: JUNCTION BOXES TO BE LOCATED ALONG <br />THE EDGE OF DECK AND 12" ABOVE COPING <br />WEDGE <br />ANCHOR <br />HANDICAPPED LIFT W/ GROUNDING <br />CC'RFw <br />/S LADDER <br />,ND/OR HANDRAIL <br />Pool Bonding Detail <br />Scale: Not to scale <br />BONDING NOTES <br />THE BONDING GRID MUST COMPLY WITH EITHER (A) OR (B) AND BE ATTACHED TO THE <br />CONDUCTIVE POOL REINFORCING STEEL AT A MINIMUM OF FOUR POINTS UNIFORMLY SPACED <br />AROUND THE PERIMETER OF THE ALLS OF A POOL, OUTDOOR SPA OR OUTDOOR HOT TUB. <br />ALTERNATE MEANS <br />WHERE STRUCTURAL REINFORCING STEEL IS NOT AVAILABLE OR IS ENCAPSULATED IN A <br />NONCONDUCTIVE COMPOUNT, A COPPER CONDUCTOR(S) SHALL BE UTILIZED WHERE THE <br />FOLLOWING REQUIREMENTS ARE MET. <br />• AT LEAST ONE MINIMUM 8 AWG BARE SOLID COPPER CONDUCTOR SHALL BE PROVIDED. <br />• THE CONDUCTORS SHALL FOLLOW THE CONTOUR OF THE PERIMETER SURFACE. <br />• ONLY LISTED SPLICES SHALL BE PERMITTED (SPLIT -BOLTS) <br />• THE REQUIRED CONDUCTOR SHALL BE 450-600 MM (IT-24") FROM THE INSIDE WALLS OF THE <br />POOL. <br />• THE REQUIRED CONDUCTOR SHALL BE SECURED WITHIN OR UNDER THE PERIMETER SURFACE <br />100 MM TO 150 MM (4" TO 6") BELOW THE SUBGRADE. CONNECT THIS SINGLE 8 AWG <br />COPPER WIRED WITH SPLIT BOLTS ON THE COPPER "WHIPS' LOCATED AT FOUR EQUAL POINTS <br />OF THE POOL. <br />0 <br />0 <br />0 <br />J <br />P4 <br />44 <br />J <br />Pq <br />0 <br />J <br />0. <br />L <br />0 <br />LL <br />Q, <br />CV <br />Z� <br />Q <br />L L1 <br />~ <br />� <br />-,0 <br />­q- <br />(y) <br />Q. <br />-.,1- <br />00 <br />0=0 <br />< <br />N <br />Z <br />0 <br />J <br />H <br />@) <br />cn <br />f <br />0 <br />= <br />I- <br />Q <br />0 <br />0 <br />l_l_l <br />Q <br />U <br />011 <br />r— <br />w <br />Q <br />Z <br />� <br />W <br />J <br />Q <br />C) <br />� <br />0 <br />m <br />():� <br />Q <br />= <br />C <br />Q <br />0 <br />0 <br />I <br />-Q <br />LL <br />CD <br />(y) <br />i= <br />W <br />R <br />U <br />J <br />0 <br />0 <br />0� <br />0 <br />Z <br />Cn <br />a <br />Z <br />Ld <br />0 <br />X <br />w <br />N <br />Z <br />a <br />Z <br />O <br />Z <br />0 <br />M <br />J <br />0 <br />0 <br />0. <br />REV. I DESCRIPTION I DATE <br />PERMIT SET 1 12-10-2021 <br />DRAWN CHECKED <br />ZJO RMT <br />DATE SCALE <br />1 2-1 7-2021 <br />SHEET 12 OF 12 <br />PE- 1 2 <br />