|
GENERAL DEMOLITION NOTES
<br />1. PRIOR TO SUBMITTING BID, VISIT SITE AND IDENTIFY EXISTING CONDITIONS AND
<br />DIFFICULTIES THAT WILL AFFECT WORK OF THIS SECTION. RENOVATION WORK WILL
<br />REQUIRE CAREFUL SITE EXAMINATION PRIOR TO BIDDING, NO COMPENSATION
<br />WILL BE GRANTED FOR ADDITIONAL WORK CAUSED BY UNFAMILIARITY WITH SITE
<br />CONDITIONS THAT ARE VISIBLE OR READILY CONSTRUED BY AN EXPERIENCED
<br />OBSERVER. FIELD VERIFY MEASUREMENTS AND CIRCUITING ARRANGEMENTS THAT
<br />ARE AS SHOWN ON DRAWINGS.
<br />2. FIELD VERIFY THAT ABANDONED WIRING AND EQUIPMENT SERVE ONLY
<br />ABANDONED FACILITIES.
<br />3. DEMOLITION DRAWINGS ARE BASED ON CASUAL FIELD OBSERVATION AND EXISTING
<br />RECORD DOCUMENTS. REPORT DISCREPANCIES TO ARCHITECT/ENGINEER BEFORE
<br />DISTURBING EXISTING INSTALLATIONS. THESE DRAWINGS HAVE BEEN COMPILED
<br />FROM THE BEST AVAILABLE INFORMATION AND ARE NOT INTENDED TO LIMIT THE
<br />SCOPE OF THE WORK. THE ELECTRICAL CONTRACTOR MAY ENCOUNTER HIDDEN OR
<br />COVERED CONDITIONS, NOT INDICATED IN THESE DOCUMENTS, REQUIRING THE
<br />ELECTRICAL CONTRACTOR TO PROVIDE ADDITIONAL WORK FOR THE COMPLETION
<br />OF HIS OR HER CONTRACT. IT WILL BE ASSUMED THAT THE CONTRACTOR HAS
<br />INSPECTED THE SITE PRIOR TO BIDDING AND VERIFIED THE INFORMATION SUPPLIED
<br />HEREIN AND ADDITIONAL WORK REQUIRED. BEGINNING OF DEMOLITION MEANS
<br />THE CONTRACTOR ACCEPTS EXISTING CONDITIONS. REFER TO ALL CONSTRUCTION
<br />DOCUMENTS TO GAIN A COMPLETE UNDERSTANDING OF THE DEMOLITION WORK
<br />REQUIRED.
<br />4. CUT, REMOVE AND LEGALLY DISPOSE OF SELECTED ELECTRICAL EQUIPMENT,
<br />COMPONENTS AND MATERIALS AS INDICATED, INCLUDING, BUT NOT LIMITED TO,
<br />REMOVAL OF ELECTRICAL ITEMS INDICATED TO BE REMOVED AND ITEMS MADE
<br />OBSOLETE BY THE WORK. DISCONNECT AND REMOVE ALL FIXTURES, WIRING
<br />DEVICES, CONDUIT AND FITTINGS, WIRING AND CABLE, FIRE ALARM
<br />DEVICES/COMPONENTS, HANGERS, SUPPORTS, WIREWAYS, AND ALL OTHER
<br />ELECTRICAL COMPONENTS MADE OBSOLETE BY THIS PROJECT. THE OWNER
<br />RESERVES THE OPTION OF SALVAGE RIGHTS TO DEMOLISHED MATERIAL AND
<br />REMOVED EQUIPMENT. THE CONTRACTOR SHALL COORDINATE WITH THE OWNER'S
<br />REPRESENTATIVE TO OBTAIN A LIST OF MATERIALS AND REMOVED EQUIPMENT TO
<br />BE TURNED OVER TO THE OWNER. ALL OTHER MATERIAL AND REMOVED
<br />EQUIPMENT NOT BEING SALVAGED BY THE OWNER SHALL BE DISPOSED OF BY THE
<br />CONTRACTOR. PLACE ALL DEMOLISHED ELECTRICAL MATERIALS EXCEPT
<br />HAZARDOUS MATERIALS (PCB LIGHTING BALLASTS, FLUORESCENT LAMPS, ETC.) AS
<br />DETERMINED BY THE AUTHORITY HAVING JURISDICTION IN GENERAL
<br />CONTRACTOR'S DUMPSTER. ALL HAZARDOUS ELECTRICAL MATERIALS SHALL BE
<br />LEGALLY DISPOSED OF BY THE ELECTRICAL SUBCONTRACTOR.
<br />S. DISCONNECT ELECTRICAL SYSTEMS IN WALLS, FLOORS, AND CEILINGS SCHEDULED
<br />FOR REMOVAL.
<br />6. MAINTAIN ACCESS TO EXISTING ELECTRICAL INSTALLATIONS WHICH REMAIN
<br />ACTIVE. MODIFY INSTALLATION OR PROVIDE ACCESS PANELS AS APPROPRIATE.
<br />TEMPORARY WALL OPENINGS AND/OR MODIFICATIONS REQUIRED FOR
<br />REMOVAL/INSTALLATION OF EQUIPMENT SHALL BE PROVIDED AS NEEDED AND
<br />COORDINATED WITH THE GENERAL CONTRACTOR. ALL HVAC, PLUMBING AND FIRE
<br />PROTECTION EQUIPMENT SCHEDULED TO BE REMOVED OR RELOCATED SHALL BE
<br />DONE SO BY THE HVAC AND PLUMBING CONTRACTOR RESPECTIVELY. THE
<br />ELECTRICAL CONTRACTOR SHALL REMOVE STARTERS, DISCONNECT SWITCHES,
<br />WIRING, AND CONDUIT FOR SAID EQUIPMENT. REFER TO HVAC AND PLUMBING
<br />DRAWINGS FOR SCOPE OF WORK.
<br />7. PROVIDE TEMPORARY WIRING AND CONNECTIONS TO MAINTAIN EXISTING
<br />SYSTEMS IN SERVICE DURING CONSTRUCTION. WHEN WORK MUST BE PERFORMED
<br />ON ENERGIZED EQUIPMENT OR CIRCUITS USE PERSONNEL EXPERIENCED IN SUCH
<br />OPERATIONS.
<br />8. EXISTING FIRE ALARM SYSTEM: MAINTAIN THE EXISTING SYSTEM IN SERVICE UNTIL
<br />THE MODIFIED/EXPANDED SYSTEM IS TESTED AND ACCEPTED BY THE FIRE
<br />DEPARTMENT. DISABLE SYSTEM ONLY TO MAKE SWITCHOVERS AND CONNECTIONS.
<br />NOTIFY OWNER, ARCHITECT/ENGINEER AND LOCAL FIRE DEPARTMENT AT LEAST
<br />TEN DAYS BEFORE PARTIALLY OR COMPLETELY DISABLING SYSTEM. MINIMIZE
<br />OUTAGE DURATION. MAKE TEMPORARY CONNECTIONS TO MAINTAIN SERVICE IN
<br />AREAS ADJACENT TO WORK AREA AS REQUIRED OR PROVIDE A "FIRE -WATCH"
<br />SYSTEM COORDINATED WITH THE LOCAL FIRE DEPARTMENT.
<br />9. EXTEND EXISTING ELECTRICAL INSTALLATIONS AS CALLED FOR ON THE DRAWINGS.
<br />10. REMOVE, RELOCATE, AND EXTEND EXISTING INSTALLATIONS TO ACCOMMODATE
<br />NEW CONSTRUCTION.
<br />11. REMOVE ABANDONED WIRING TO SOURCE OF SUPPLY.
<br />12. REMOVE EXPOSED ABANDONED CONDUIT, INCLUDING ABANDONED CONDUIT
<br />ABOVE ACCESSIBLE CEILING FINISHES. CUT CONDUIT FLUSH WITH WALLS AND
<br />FLOORS, AND PATCH SURFACES.
<br />13. DISCONNECT ABANDONED OUTLETS AND REMOVE DEVICES. REMOVE ABANDONED
<br />OUTLETS IF CONDUIT SERVICING THEM IS ABANDONED AND REMOVED. PROVIDE
<br />BLANK COVER FOR ABANDONED OUTLETS WHICH ARE NOT REMOVED.
<br />14. DISCONNECT AND REMOVE ELECTRICAL DEVICES AND EQUIPMENT SERVING
<br />UTILIZATION EQUIPMENT THAT HAS BEEN REMOVED.
<br />15. DISCONNECT AND REMOVE ABANDONED LIGHTING FIXTURES. REMOVE BRACKETS,
<br />STEMS, HANGERS, AND OTHER ACCESSORIES.
<br />16. DISCONNECT AND REMOVE OTHER SYSTEMS AND EQUIPMENT WITHIN THE WORK
<br />AREA MADE OBSOLETE BY THIS WORK.
<br />17. PROTECT ALL EXISTING WALLS, FLOORS, CEILINGS, LIGHT FIXTURES, ETC, WHICH ARE
<br />TO REMAIN AND TO PREVENT DAMAGE DURING ALL CONSTRUCTION PHASES.
<br />REPAIR ADJACENT CONSTRUCTION AND FINISHES DAMAGED DURING DEMOLITION
<br />AND EXTENSION WORK. PROVIDE AND MAINTAIN TEMPORARY PARTITIONS OR
<br />DUST BARRIERS ADEQUATE TO PREVENT THE SPREAD OF DUST AND DIRT TO
<br />ADJACENTAREAS. PROTECTTHE STRUCTURE, FURNISHINGS, FINISHES, AND
<br />ADJACENT MATERIALS NOT INDICATED OR SCHEDULED TO BE REMOVED. PROTECT
<br />THE ELECTRICAL WORK AND THE WORK OF OTHERS IN A MANNER BEST SUITED TO
<br />THE PARTICULAR CASE. CORRECT ANY DAMAGE DONE TO ANY WORK AT NO
<br />ADDITIONAL COST.
<br />18. EXTEND EXISTING INSTALLATIONS USING MATERIALS AND METHODS COMPATIBLE
<br />WITH EXISTING ELECTRICAL INSTALLATIONS, OR AS SPECIFIED.
<br />19. CLEAN AND REPAIR EXISTING MATERIALS AND EQUIPMENT WHICH REMAIN OR ARE
<br />TO BE REUSED.
<br />20, PANELBOARDS: CLEAN EXPOSED SURFACES AND CHECK TIGHTNESS OF ELECTRICAL
<br />CONNECTIONS. REPLACE DAMAGED CIRCUIT BREAKERS AND PROVIDE CLOSURE
<br />PLATES FOR VACANT POSITIONS. PROVIDE TYPED CIRCUIT DIRECTORY SHOWING
<br />REVISED CIRCUITING ARRANGEMENT.
<br />21. LIGHTING FIXTURES: EXISTING LIGHTING FIXTURES SCHEDULED FOR REUSE SHALL BE
<br />REMOVED FOR CLEANING. USE MILD DETERGENT TO CLEAN ALL EXTERIOR AND
<br />INTERIOR SURFACES; RINSE WITH CLEAN WATER AND WIPE DRY. REPLACE LAMPS,
<br />BALLASTS AND BROKEN ELECTRICAL PARTS.
<br />22. EXISTING ELECTRICAL EQUIPMENT AND WIRING NOT SHOWN ON DOCUMENTS OR
<br />ADDRESSED BY NOTES ABOVE SHALL BE CONSIDERED EXISTING TO REMAIN.
<br />EXISTING ELECTRICAL EQUIPMENT LEGEND
<br />ALL ITEMS SHOWN ARE NOT NECESSARILY USED ON THIS PROJECT
<br />�F 0
<br />EXISTING ELECTRICAL EQUIPMENT WITHOUTA DESIGNATION IS TO REMAIN.
<br />XE XE XE XE
<br />"XE" INDICATES EXISTING ELECTRICAL EQUIPMENT WHICH IS TO BE REMOVED.
<br />LFJ 2 0 P
<br />PULL BACK WIRING AND CONDUIT BACK TO NEXT ACTIVE OUTLET OR POWER
<br />SOURCE.
<br />XR XR XR
<br />"XR" INDICATES EXISTING ELECTRICAL EQUIPMENT TO BE REMOVED AND
<br />M 2 XR I1TI
<br />RELOCATED. EXISTING CIRCUIT SHALL BE EXTENDED TO NEW LOCATION OF
<br />tY
<br />RELOCATED EXISTING ELECTRICAL EQUIPMENT.
<br />XNXNXNXN XN
<br />2 7 [P
<br />"XN" INDICATES NEW LOCATION OF RELOCATED EXISTING ELECTRICAL
<br />EQUIPMENT.
<br />"ETR" INDICATES EXISTING EQUIPMENT/DEVICE TO REMAIN. EXISTING CIRCUIT/
<br />ETR ETR ETR ETR
<br />WIRING SHALL BE REMOVED. PULL BACK WIRING AND CONDUIT BACK TO NEXT
<br />I F 27 IP
<br />ACTIVE OUTLET OR POWER SOURCE. ALL HVAC/PLUMBING INTERLOCKING
<br />WIRING SHALL REMAIN, REFER TO RENOVATION PLANS FOR NEW CIRCUIT
<br />INFORMATION.
<br />�XW, XW XW XW
<br />"XW" INDICATES EXISTING EQUIPMENT/DEVICE TO BE REMOVED. EXISTING
<br />M 2 01P
<br />CIRCUIT/WIRING AND BACK BOX SHALL REMAIN. NEW DEVICE SHALL BE
<br />XW XW XW XW
<br />LOCATED IN PLACE. EXTEND CIRCUIT/WIRING TO NEW ELECTRICAL
<br />nQ 0 qp
<br />EQUIPMENT/DEVICE.
<br />GENERAL NOTES:
<br />1. DOTTED SYMBOLS
<br />INDICATE EXISTING ELECTRICAL EQUIPMENT.
<br />2. REFER TO
<br />SPECIFICATIONS FOR ADDITIONAL INFORMATION.
<br />3. ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR ENSURING THE CONTINUITY OF ALL
<br />EXISTING CIRCUITS WHICH ARE REMAINING.
<br />CLG
<br />ETR
<br />fr 1
<br />r TIfT -1-
<br />f- T►fr 1
<br />r -nfr 1
<br />U_J
<br />-1
<br />L1JLLJ - R/F
<br />-nrr
<br />L1JU-J
<br />1fr
<br />L_LILJ
<br />fr
<br />r 1
<br />r 1
<br />f--nfr 1
<br />LL J
<br />L _UU_ J
<br />L _UH J
<br />L 1JLL J
<br />CIRCUIT TRACING NOTE
<br />ELECTRICAL CONTRACTOR SHALL UPDATE ALL EXISTING PANELBOARD DIRECTORIES TO
<br />REFLECT ALL CIRCUITS MADE SPARE FROM DEMOLITION. ALL EXISTING CIRCUIT BREAKERS IN
<br />ALL EXISTING PANELBOARDS SHOWN ON THE DRAWINGS SHALL BE TRACED OUT AND LABELED
<br />IN PANELBOARD OF ORIGIN. ALL CIRCUITS THAT ARE NO LONGER IN USE SHALL BE PULLED
<br />BACK TO PANEL OF ORIGIN. ALL CIRCUIT BREAKERS NOT BEING UTILIZED SHALL BE LABELED AS
<br />SPARE AND PUT IN THE OPEN (OFF) POSITION.
<br />KEYED NOTES
<br />r1 DISCONNECT AND THEN RECONNECT EXISTING CEILING MOUNTED RECEPTACLES TO
<br />�� ACCOMMODATE NEW CEILING.
<br />ETR
<br />_,I -nrr 1
<br />rir�r —Ji
<br />L 1JLL J
<br />CLG
<br />ETR , y;
<br />r� —1
<br />Uk
<br />r-11T 1
<br />TR
<br />r -nrr -
<br />r -nrr —1
<br />L SJLL J
<br />r-nfT1
<br />L JL -i >
<br />rTfT1-._: R/F
<br />L _LILL. J
<br />rilfr1
<br />L11LL.J
<br />LIILLJ
<br />L1IlLJ
<br /><�� �>
<br /><�� �J,>
<br /><�� �J,>
<br />CLG CLG
<br />ETR .._') ETR
<br />uR
<br />F-"f11T-1
<br />TR
<br />r- -nff-4 ,
<br />F -nfT-1
<br />L11LL.J
<br />r -1fr 1
<br />L HLL. jal
<br />r -nfr - R/F
<br />LJLLJ
<br />r ilfr-1
<br />LIJLLJ
<br />L_ULJ
<br />L HU_J
<br />ET
<br />r ilff -1
<br />� -nrr -1
<br />L _LI L J
<br />L I IU_ J
<br />i -11
<br />i- i
<br />P
<br />�a
<br />U
<br />U
<br />I
<br />r-n(T1
<br />r�1fr-1ETR
<br />rT1fT1
<br />rTI
<br />L 1JLL J
<br />L 1JL J
<br />L 1JLL J
<br />L 11
<br />r Tif -1
<br />r -nfr 1_ ___ R/F
<br />r TIIT 1
<br />r it
<br />L _LILI_n
<br />n_ULI_n
<br />n_UULn
<br />/L_LI ETR
<br />ETR CLG
<br />CLG
<br />CLG
<br />CLG CLG
<br />CLG
<br />ETR ETR ,
<br />ETR l,:
<br />ETR _
<br />0 ETR ETR .:
<br />ETR ,
<br />ETR
<br />ETR
<br />ETR
<br />ETR
<br />ETR
<br />CLG
<br />ETR ETR
<br />ETR'
<br />EXISTING MAIN ELECTRIC ROOM EQUIPMENT
<br />IS EXISTING TO REMAIN.
<br />ETR
<br />ETR
<br />ETR
<br />ETR
<br />ETR
<br />ETR
<br />R/F
<br />ETR
<br />;ETR ETR ETR ETR
<br />f, - - - - - ------ - - - ---------
<br />-_ --_- ______ -- - - - - - - - -
<br />�I
<br />XE XE
<br />j XE I 1
<br />------------------------
<br />El°R� L---------------------------.li I IU
<br />ETR
<br />R/F i
<br />ETR -
<br />I � T
<br />-------`i �-------= —
<br />�;.__� ETR - - - -I r
<br />i r
<br />II
<br />I
<br />ETR I I XE XE IL - - - - - - - - -
<br />- - - - - - - - - ETR
<br />I II
<br />R/F R
<br />I
<br />I XEI ETR
<br />-JETR XE._ L_--------J ETR E
<br />------
<br />ETR - R/F - ETR - R/F
<br />ETR ETR ETR ETR" - -- R/F
<br />T
<br />` �i
<br />ELECTRICAL DEMOLITION
<br />SCALE:1/8" =1'-0"
<br />0 8' 0' 16'-0" 24'-0"
<br />ETR
<br />ETR
<br />ETR
<br />'R/F
<br />ETR
<br />ETR
<br />ETR
<br />ETR
<br />ETR
<br />ETR_`
<br />ETR-
<br />ETR'
<br />ETR
<br />PROJECT:
<br />PINCHASERS EAST PASCO
<br />ANTHONY PERRONE
<br />6816 GALL BOULEVARD
<br />ZEPHYRHILLS, FL 33542
<br />PROJECT NUMBER: 21161
<br />(jr)
<br />00
<br />NU
<br />.
<br />o LU
<br />WqU
<br />LU
<br />U��
<br />� <t
<br />J O U
<br />ce o
<br />W°�
<br />O�'
<br />w
<br />I _ o
<br />(y) `o
<br />ov
<br />w in
<br />I— u0
<br />r
<br />�/ V) v
<br />V)"T
<br />0
<br />F_ Lo
<br />w u-
<br />w U w
<br />N
<br />N N
<br />Z qN
<br />y w r
<br />I.
<br />LJ_J Z N
<br />w
<br />U 00
<br />Q o
<br />N L7
<br />cy)
<br />F
<br />V _s4 o
<br />0
<br />^, H M M
<br />M
<br />V/
<br />40,
<br />a C) ccn
<br />Q 0 00 00 O
<br />U
<br />1� 4�
<br />N
<br />O 0PLO
<br />m 00
<br />STAMP:
<br />.-
<br />ISSUE:
<br />DATE:
<br />ISSUED FOR PERMIT
<br />01 /25/2023
<br />DRAWING SCALE: NOTED
<br />DRAWN BY: SB
<br />CHECKED BY: MD
<br />DRAWING TITLE:
<br />ELECTRICAL - DEMOLITION
<br />DRAWING NUMBER:
<br />ED 1,90
<br />
|