|
EQUIPMENT WIRING SCHEDULE
<br />AMPACITY
<br />WIRE AND CONDUIT SIZE
<br />15,20
<br />1
<br />2#12 + 1#12 GROUND IN 3/4" CONDUIT
<br />15,20
<br />3
<br />3#12 + 1#12 GROUND IN 3/4" CONDUIT
<br />25,30
<br />1
<br />2#10 + 1#10 GROUND IN 3/4" CONDUIT
<br />25,30
<br />3
<br />3#10 + 1#10 GROUND IN 3/4" CONDUIT
<br />35,40
<br />1
<br />2#8 + 1#10 GROUND IN 3/4" CONDUIT
<br />35,40
<br />3
<br />3#8+ 1#10 GROUND IN 3/4" CONDUIT
<br />45,50,55
<br />1
<br />2#6 + 1#10 GROUND IN 3/4" CONDUIT
<br />45,50,55
<br />3
<br />3#6 + 1#10 GROUND IN 3/4" CONDUIT
<br />60
<br />1
<br />2#4 + 1#10 GROUND IN 1" CONDUIT
<br />60
<br />3
<br />3#4 + 1#10 GROUND IN 1" CONDUIT
<br />70
<br />3
<br />3#4 + 1#8 GROUND IN 1" CONDUIT
<br />80
<br />3
<br />3#3 + 1#8 GROUND IN 1-1/4" CONDUIT
<br />90
<br />3
<br />3#2 + 1#8 GROUND IN 1-1/4" CONDUIT
<br />100,110
<br />3
<br />3#1 + 1#6 GROUND IN 1-1/4" CONDUIT
<br />125,150
<br />3
<br />3#1/0 + 1#6 GROUND IN 1-1/2" CONDUIT
<br />175
<br />3
<br />3#2/0 + 1#6 GROUND IN 2" CONDUIT
<br />200
<br />3
<br />3#3/0 + 1#4 GROUND IN 2" CONDUIT
<br />NOTE:
<br />1. THE AMPERAGE AND PHASE OF THE WIRING ON THIS SCHEDULE
<br />CORRESPONDS TO THE CIRCUIT BREAKER SIZE IN THE ELECTRICAL
<br />CONNECTION SCHEDULE FOR MECHANICAL EQUIPMENT.
<br />PROVIDE WIRING AS INDICATED UNLESS OTHERWISE SPECIFIED.
<br />2, WIRE SIZE IS BASED ON THE USE OF COPPER CONDUCTORS.
<br />FIRE STOPPING NOTES
<br />LIGHT FIXTURE SCHEDULE
<br />TYPE
<br />FIXTURE DESCRIPTION
<br />MANUFACTURER
<br />CATALOG NO.
<br />MOUNTING
<br />LAMPING
<br />VOLTAGE
<br />DESCRIPTION/REMARKS
<br />TYPE
<br />WATTAGE
<br />A
<br />6" DOWNLIGHT
<br />(TO BE SELECTED)
<br />-
<br />RECESSED
<br />LED
<br />-
<br />120
<br />6" RECESSED LED DOWNLIGHT
<br />B
<br />6" PENDANT
<br />(TO BE SELECTED)
<br />-
<br />PENDANT
<br />LED
<br />-
<br />120
<br />6" DECORATIVE PENDANT LIGHT
<br />C
<br />8' LED STRIP
<br />(TO BE SELECTED)
<br />-
<br />RECESSED
<br />LED
<br />-
<br />120
<br />8' LED STRIP LIGHT
<br />D
<br />2'x4' LIGHT FIXTURE
<br />(TO BE SELECTED)
<br />-
<br />RECESSED
<br />LED
<br />-
<br />120
<br />2'x4' RECESSED LED LIGHT
<br />E
<br />ACCENT LIGHT
<br />(TO BE SELECTED)
<br />-
<br />WALL
<br />LED
<br />-
<br />120
<br />3ECORATIVE WALL MOUNTED PENDANT ACCENT LIGHT
<br />F
<br />PENDANT FIXTURE
<br />(TO BE SELECTED)
<br />-
<br />PENDANT
<br />LED
<br />-
<br />120
<br />LARGE DECORATIVE PENDANT LIGHT
<br />G
<br />DIRECTIONAL DOWNLIGHT
<br />(TO BE SELECTED)
<br />-
<br />RECESSED
<br />LED
<br />-
<br />120
<br />6" RECESSED LED DIRECTIONAL DOWNLIGHT
<br />NOTES:
<br />1. PROVIDE ACCESSORIES AND MOUNTING HARDWARE AS REQUIRED FOR ALL LIGHT FIXTURES.
<br />2. FIXTURE/ACCESSORY COLORS NOT INDICATED ON THE DRAWINGS SHALL BE SELECTED BY ARCHITECT.
<br />3. PROVIDE LAMPING FOR ALL FIXTURES UNLESS LAMPING IS INCLUDED WITH FIXTURE.
<br />4. PROVIDE TYPICAL MOCK-UP FOR LIGHT FIXTURE HANGING HEIGHTS AND EXPOSED ELECTRICAL CONDUIT LAYOUT TO BE REVIEWED BY ARCHITECT.
<br />5. ALL LIGHT FIXTURES WITH INCANDESCENT OR FLOURESCENT LAMPING SHALL BE PROVIDED WITH A COMPATIBLE LED LAMP.
<br />6. COLOR AND FIN ISH OF ALL LIGHT FIXTURES SHALL BE APPROVED BY OWNER/ARCHITECT PRIOR TO THE SUBMITTAL OF SHOP DRAWINGS.
<br />1. GENERAL: FIRE STOPPING SHALL BE PROVIDED BY THIS CONTRACTOR FOR ALL
<br />FLOOR, CEILING AND FIRE RATED WALL PENETRATIONS FOR CONDUIT, SLEEVES
<br />AND/OR CABLING AS REQUIRED BY JOB CONDITIONS.
<br />2. THE CONTRACTOR SHALL PROVIDE A FIRE STOP SYSTEM IN ACCORDANCE WITH THE
<br />FOLLOWING:
<br />2.1. THE SYSTEM SHALL CONSIST OF A WATER BASED SEALANT AND SUITABLE
<br />DAMMING MATERIALS (WHERE REQUIRED) AND BE INSTALLED PER
<br />MANUFACTURER'S REQUIREMENTS.
<br />2.2. THE SEALANT SUPPLIED SHALL BE A TWO STAGED INTUMESCENT AND CAPABLE
<br />OF EXPANDING UP TO 8 TIMES ITS ORIGINAL VOLUME.
<br />2.3. THE SEALANT SUPPLIED SHALL CONTAIN NO ASBESTOS, NO FIBERGLASS, AND
<br />NO SOLVENTS NOT CORROSIVE MINERAL SALTS OF ANY KIND.
<br />2.4. THE SEALANT SHALL FORM A SURFACE CAPABLE OF BEING SANDED AND
<br />PAINTED TO MATCH SURROUNDING SURFACES AND SHALL BE IMPERVIOUS TO
<br />WATER WHEN DRY.
<br />2.5. THE FIRE STOP SYSTEM SHALL BE TESTED TO THE TIME/TEMPERATURE
<br />REQUIREMENTS OF ASTM E119 AND SHALL BE UL1479 (ASTM E814) AND
<br />CLASSIFIED FOR UP TO 3 HOURS.
<br />2.6. THE FIRE STOP SEALANT SHALL BE SPECSEAL SEALANT AS MANUFACTURED BY
<br />SPECIFIED TECHNOLOGIES, INC. OR APPROVED EQUAL.
<br />2.7. SPECIAL CARE SHALL BE TAKEN WITH ELECTRICAL SYSTEMS NOT TO
<br />COMPROMISE ANY OF THE BUILDING FIRE PARTITIONS, FLOORS, WALLS OR
<br />MEMBRANES. PROVIDE ALL FIRESTOPPING REQUIRED TO COMPLY WITH THE
<br />BUILDING CODE, THE ELECTRICAL CODE AND THE UL LISTING OF EACH
<br />ASSEMBLY. COORDINATE LOCATIONS AND TYPES OF MEMBRANES WITH
<br />ARCHITECT.
<br />SEISMIC RESTRAINT NOTES
<br />1, GENERAL: IT IS THE INTENT OF THIS SEISMIC SPECIFICATION TO KEEP ALL ELECTRICAL
<br />BUILDING SYSTEM COMPONENTS IN PLACE DURING A SEISMIC EVENT. ALL
<br />ELECTRICAL SYSTEMS MUST BE INSTALLED IN STRICT ACCORDANCE WITH SEISMIC
<br />CODES, COMPONENT MANUFACTURER'S AND BUILDING CONSTRUCTION
<br />STANDARDS. WHENEVER A CONFLICT OCCURS BETWEEN THE MANUFACTURER'S OR
<br />CONSTRUCTION STANDARDS, THE MOST STRINGENT SHALL APPLY.
<br />2. THIS CONTRACTOR SHALL ENGAGE A PROFESSIONAL STRUCTURAL ENGINEER
<br />REGISTERED IN THE JURISDICTION OF THIS PROJECT TO REVIEW THE ENTIRE
<br />INSTALLATION TO DETERMINE ALL SEISMIC RESTRAINT REQUIREMENTS AND
<br />METHODS. CONTRACTOR SHALL SUBMIT A REPORT OUTLINING THE STRUCTURAL
<br />ENGINEER'S REVIEW AS WELL AS SEISMIC RESTRAINT SHOP DRAWINGS AND
<br />SUPPORTING CALCULATIONS PREPARED BY THE PROFESSIONAL STRUCTURAL
<br />ENGINEER FOR REVIEW BY THE ARCHITECT.
<br />3. SEISMIC RESTRAINTS SHALL BE DESIGNED IN ACCORDANCE WITH SEISMIC FORCE
<br />LEVELS AS DETAILED IN THE APPLICABLE BUILDING CODE.
<br />3.1. ALL EQUIPMENT, CONDUITAND PULL BOXES SHALL BE ADEQUATELY
<br />RESTRAINED TO RESIST SEISMIC FORCES. RESTRAINT DEVICES SHALL BE
<br />DESIGNED AND SELECTED TO MEET SEISMIC REQUIREMENTS AS DEFINED IN
<br />THE LATEST ISSUE OF THE BOCA NATIONAL BUILDING CODE IN ACCORDANCE
<br />WITH THE APPLICABLE SEISMIC ZONE.
<br />3.2. ANCHOR BOLT CALCULATORS, SIGNED AND STAMPED BY A REGISTERED
<br />PROFESSIONAL ENGINEER, SHALL BE SUBMITTED SHOWING ADEQUACY OF THE
<br />BOLT SIZING AND TYPE, STAMPED CALCULATIONS SHALL ALSO BE FURNISHED
<br />FOR ANCHORS ON RESTRAINT DEVICES, CABLES, ISOLATORS AND RIGIDLY
<br />MOUNTED EQUIPMENT.
<br />INSTALLED EVERY 25 DEVICES
<br />PANELBOARD: LP1
<br />AI C : 100, 000
<br />BUS RATING: 1225A I
<br />225 A, 208Y1120 V, 3 PH, 4 W, 60 HZ
<br />MAIN LUG ONLY
<br />MAIN CIRCUIT BREAKER X
<br />FLUSH MOUNTEDB
<br />SURFACE MOUNTED X
<br />NOTES:
<br />LC =
<br />VIA LIGHTING CONTROL PANEL
<br />G =
<br />GFCI - 5mA TRIP
<br />P =
<br />GFPE - 30 mA TRIP
<br />S =
<br />SHUNT TRIP
<br />L =
<br />PROVIDE LOCK ON CB
<br />SHUNT TRIP MAIN
<br />200% RATED NEUTRAL
<br />ISOLATED GROUND
<br />FEED THRU LUGS
<br />100% RATED MAIN BREAKER
<br />GROUND FAULT MAIN C.B.
<br />CKT
<br />No.
<br />LOAD
<br />Note
<br />WIRE
<br />SIZE
<br />CIRCUIT BREAKERS
<br />CKT
<br />No.
<br />LOAD
<br />Note
<br />WIRE
<br />SIZE
<br />CIRCUIT BREAKERS
<br />o
<br />N
<br />Q
<br />m
<br />m
<br />U
<br />U
<br />o
<br />p
<br />w
<br />W
<br />U-(9
<br />U-
<br />(�
<br />o
<br />N
<br />m
<br />m
<br />m
<br />U
<br />v
<br />0
<br />p
<br />p
<br />p
<br />w
<br />w
<br />w
<br />U-
<br />LL
<br />u—
<br />C9
<br />(�
<br />1
<br />LIGHTING
<br />1
<br />2
<br />LIGHTING
<br />1
<br />3
<br />LIGHTING
<br />1
<br />4
<br />LIGHTING
<br />1
<br />5
<br />LIGHTING
<br />1
<br />6
<br />LIGHTING
<br />1
<br />7
<br />LIGHTING
<br />1
<br />8
<br />LIGHTING
<br />1
<br />9
<br />LIGHTING
<br />1
<br />10
<br />RECEPTACLES
<br />1
<br />11
<br />RECEPTACLES
<br />1
<br />12
<br />ARCADE
<br />1
<br />13
<br />ARCADE
<br />1
<br />14
<br />ARCADE
<br />1
<br />15
<br />ARCADE
<br />1
<br />16
<br />ARCADE
<br />1
<br />17
<br />ARCADE
<br />1
<br />18
<br />DESK
<br />1
<br />19
<br />RECEPTACLES
<br />1
<br />20
<br />SPARE
<br />21
<br />SPARE
<br />22
<br />SPARE
<br />23
<br />SPARE
<br />24
<br />SPARE
<br />25
<br />SPARE
<br />26
<br />SPARE
<br />27
<br />SPARE
<br />28
<br />SPARE
<br />29
<br />SPARE
<br />30
<br />SPARE
<br />31
<br />SPARE
<br />32
<br />SPARE
<br />33
<br />SPARE
<br />34
<br />SPARE
<br />35
<br />SPARE
<br />36
<br />SPARE
<br />37
<br />SPARE
<br />38
<br />SPARE
<br />F39
<br />SPARE
<br />40
<br />SPARE
<br />41
<br />SPARE
<br />42
<br />SPARE
<br />Im
<br />F �T L kSD CM CM SD D Sp D
<br />kSD kSD RTS RTS ( — _
<br />24V WIRING I 2 � TO ADDITIONAL
<br />�? DEVICES
<br />IM CM IM I F F F F �B
<br />EXISTING 177cd 177cd 75cd 75cd
<br />— ( 1 FIRE ALARM
<br />POWER
<br />SUPPLY ( 1
<br />EXISTING I �' AP7S] (TYP.)
<br />ADDRESSABLE —
<br />MAI N L 20AJ1 P
<br />FIRE ALARM � �120V
<br />CONTROL PANEL. I � � 3
<br />CAC �► iti
<br />20A/1P _
<br />120-V/
<br />i
<br />O1 ALL STROBES SHALL BE SYNCHRONIZED. EXACT METHOD FOR SYNCHRONIZATION SHALL BE
<br />SPECIFIC TO EACH FIRE ALARM MANUFACTURER. PROVIDE EVIDENCE OF SYNCHRONIZATION IN
<br />FIRE ALARM SUBMITTAL.
<br />20 PROVIDE ISOLATION MODULES AT EITHER SIDE OF FIRE ALARM MODULES FOR BOOSTER PANELS
<br />AND MASTER BOX, TYPICAL,
<br />OPARTIAL FIRE ALARM RISER DIAGRAM
<br />SCALE: N.T.S.
<br />FIRE ALARM SYSTEM GENERAL NOTES:
<br />1. ALL WIRING SHALL BE PER MANUFACTURER'S SPECIFICATIONS.
<br />2. THIS SCHEMATIC IS TYPICAL. WIRE TO ALL DEVICES ON ALL LOOPS AND CIRCUITS. SEE PLAN VIEWS FOR TYPES AND QUANTITIES
<br />OF DEVICES.
<br />3. ALL FIRE ALARM WIRING SHALL BE RUN CONTINUOUS FROM DEVICE TO DEVICE. (SEE RIUFC).
<br />4. OUTGOING AND RETURN CONDUCTORS MUST BE RUN IN SEPARATE RACEWAYS. PROVIDE MINIMUM SEPARATION OF 1 FOOT
<br />WHERE THE CABLE IS RUN VERTICALLY AND A 4 FEET SEPARATION WHERE THE CABLE IS RUN HORIZONTALLY. (SEE RIUFC AND NFPA).
<br />5. PROVIDE ANY ADDITIONAL REMOTE POWER SUPPLIES AS NECESSARY, PROVIDE ADDITIONAL SMOKE DETECTORS AS NECESSARY
<br />PER NFPA.
<br />6. PROVIDE INTERMEDIATE RELAYS AS NEEDED.
<br />7. SYNCHRONIZE ALL STROBE LIGHTS.
<br />8. VERIFY WIRING TYPE FOR INITIATING LOOP.
<br />9. VERIFY ADDITIONAL WIRING (e.g. 24V POWER FOR MODULES) WITH SPECIFIED MANUFACTURER.
<br />10. PROVIDE NEW FIRE ALARM POWER SUPPLIES, DEVICES, WIRING, ETC, AS REQUIRED TO SERVE NEW FIRE ALARM NOTIFICATION
<br />DEVICES SHOWN ON THE DRAWINGS.
<br />11. PROVIDE ISOLATION MODULES AS REQUIRED IN ACCORDANCE WITH THE RHODE ISLAND FIRE SAFETY CODE. PROVIDE
<br />AN ISOLATION MODULE FOR EVERY 25 INITIATING DEVICES.
<br />12. PROVIDE 25% SPARE CAPACITY ON INITIATIONS AND NOTIFICATIONS LOOPS.
<br />13. ALL FIRE ALARM EQUIPMENT INCLUDING AND NOT LIMITED TO FIRE ALARM PANELS, CABINETS, ANNUNCIATOR, PULL STATIONS,
<br />ETC. SHALL BE LOCKABLE TYPE. PROVIDE KEY ALIKE LOCKABLE EQUIPMENT AS REQUIRED.
<br />PROJECT:
<br />PINCHASERS EAST PASCO
<br />ANTHONY PERRONE
<br />6816 GALL BOULEVARD
<br />ZEPHYRHILLS, FL 33542
<br />PROJECT NUMBER: 21 161
<br />Ln 0
<br />M O
<br />O
<br />cv U
<br />_.J o U
<br />WQLU
<br />�Q
<br />_J 06
<br />ck� D
<br />Lu m 3:
<br />O10
<br />x0 �
<br />O d
<br />u 10M 10
<br />w L.
<br />F- �
<br />v = �C)
<br />r /J � �0;
<br />0
<br />■� ,n
<br />��
<br />z w.
<br />(v) me
<br />�
<br />N
<br />z
<br />er
<br />Z N
<br />w
<br />U CO
<br />Q o
<br />C'4 L0
<br />co
<br />rL.
<br />a�
<br />c�
<br />N
<br />OMO 4 i
<br />O
<br />• F* M
<br />M
<br />U p 00 00
<br />N
<br />O
<br />oo
<br />�VM
<br />STAMP:
<br />x,v.
<br />y L i
<br />�c
<br />r�
<br />rro4,�.
<br />ISSUE:
<br />DATE:
<br />ISSUED FOR PERMIT
<br />01 /25/2023
<br />DRAWING SCALE: NOTED
<br />DRAWN BY: SB
<br />CHECKED BY: MD
<br />DRAWING TITLE:
<br />ELECTRICAL - SCHEDULES
<br />DRAWING NUMBER:
<br />E260
<br />
|