|
'A
<br />�
<br />Doors into Rated Corridor, Electromagnetic Holdopen, Panic Bar on one side for
<br />impact resistance, Swing -Clear Hinges
<br />3 each Hinges BB 1262 X 4.5 X 26D (Swing Clear)
<br />I Exit Device W/Lever Out 99L-F X 994LX 06 X SN_B X SP28
<br />LAR
<br />I Closer 8301BF, 3301BF, or
<br />1461 X SNI3 X AL
<br />I Electromagnetic Holder
<br />997 X AL X 24 VOLT
<br />3.7.5 Group C-1
<br />Exit Door (Panic Bar), no Alarm, from Rated Enclosure which has no other traffic,
<br />W/Closer (occurs only in Remodels and New Stores which require an added rated
<br />Exit Corridor due to adjacent buildings)
<br />3 each Hinges
<br />BB 1279 X 4,5 X 4.5 NRP X USP
<br />I Exit Device
<br />99EO-F X SNB X SP28 LAR
<br />I Closer, W/Stop, W/O H.O.
<br />CLP8301BF, 332113F, or
<br />146 1 -CUSH X SNI3 X AL
<br />I Door Sweep
<br />57AV
<br />I Set Weather -Strip
<br />S88D
<br />3.7.6 Group C-2
<br />Exit Access Door (Panic Bar), with Alarm, into
<br />Rated Enclosure which has no other
<br />traffic, W/B-Label & Closer (Occurs only in Remodels and New Stores which
<br />require an added rated Exit Corridor due to adjacent buildings)
<br />3 each Hinges
<br />BB 1279 X 4.5 X 4.5 X 26D
<br />I Exit Device W/Lever Out
<br />99L-F X 994L X 06 X ALK-S2 X SNB
<br />X SP28 LAR
<br />I Cylinder for Alarm
<br />(Furnished & Installed by Publix)
<br />I Closer, W/O Stop, W/O H.O.
<br />8301BF, 33011317, or
<br />1461 X SNB; X AL
<br />I Door Stop
<br />407 1/2 B or 438B 26D as required
<br />3.7.7 Group D
<br />Lockset, can be disabled from inside� Offices, Bookkeeping Conference/Training
<br />Rooms, Storage Rooms:
<br />3 each Hinges
<br />BB 1279 X 4�5 X 4.5 X 26D
<br />I Entrance Lockset
<br />D53PD X Rhodes X 626
<br />1 Door Stop
<br />407 1/2 B or 438B 26D as required
<br />3.7.8 Group D-I
<br />Lockset, can be disabled from inside: Single toilets:
<br />3 each Hinges
<br />BB 1279 X 4.5 X 4.5 X 26D
<br />I Entrance Lockset
<br />D40PD X Rhodes X 626
<br />1 Door Stop
<br />407 1/2 B OR 438B 26D as required
<br />3.7.9 Group E
<br />Lockset, can be disabled from inside, with Closer: Doors from Sales Area to
<br />Customer Service and Office Area and Door(s) from Elec. Equip. Room to Interior,
<br />single toilet Restrooms
<br />3 each Hinges
<br />BB 1 279 X 4.5 X 4.5 X 26D
<br />I Entrance Lockset
<br />D53PD X Rhodes X 626
<br />1 Closer
<br />830 IBF, 3301 BF, or
<br />1461 X SN13 X AL
<br />I Door Stop
<br />407 1/2 B or 438B 26D as required
<br />17. 1 0 Group F- I
<br />Lockset, key -operated only� (Single) Equipment Closet Doors
<br />3 each Him�es
<br />�
<br />1279 X 4.5 X 4.5 26D
<br />I Storeroom Lockset
<br />D80PD X Rhodes X 626
<br />1 Door Stop
<br />407 1/2 or 438B 26D as required
<br />3.7.11 Group F-2
<br />Lockset, key -operated only: Pairs of Equipment
<br />Closet Doors
<br />6 each Hinges
<br />1279 X 4.5 X 4.5 X 26D
<br />I Storeroom Lockset
<br />D80PD X Rhodes X 626
<br />2 Door Stops
<br />407 1/2 B or 438B 26D as required
<br />I pair Flush Bolts
<br />458B 26D X 12"
<br />1 Dust Proof Strike
<br />489 X 487 B26D
<br />3.7.12 Group G
<br />Lockset, key -operated only, with Closer: Cash
<br />Room
<br />3 each Hinges
<br />BB 1279 X 4.5 X 4.5 X 26D
<br />I Storeroom Lockset
<br />D80PD X Rhodes X 626
<br />1 Closer
<br />830113F, 330113F, or 1461 X SNB X
<br />AL
<br />I Door Stop
<br />407 1/2 B or 438B 26D as required
<br />3.7.13 Group H
<br />Passage Set and Deadlocks: Dutch Door at Pharmacy
<br />4 each Hinges
<br />1279 X 4.5 X 4.5 26D
<br />I Passage Set
<br />D I OS X Rhodes X 626
<br />2 Deadlock (CYL X T/T)
<br />B16ON X 626
<br />1 Door Stop
<br />407 1/2 B or 438B 26D as required
<br />3.7.14 Group J
<br />Passage Set: Non -Locking Storage & Equipment, Passage Doors
<br />3 each Hinges
<br />1279 X 4.5 X 4.5 X 26D
<br />I Passage Set
<br />D I OS X Rhodes X 626
<br />1 Door Stop
<br />407 1/213 or 43 8B 26D as required
<br />1
<br />3.7.15 Group K
<br />Restrooms, Passage Door in Office Area
<br />3 each Hinges
<br />BBI 279 X 4.5 X 4�5 X 26D
<br />I Push Plate
<br />8200 X 8 X 16 X 32D
<br />I Door Pull
<br />8303-8 X 4 X 16 X 32D
<br />I Closer
<br />830113F, 330113F, or 1461 X SNB X
<br />AL
<br />I Kick Plate
<br />8 X 2" X LDW X 32D
<br />I Door Stop
<br />407 1/2 B or 438B 26D as required
<br />3.7.16 Group L I
<br />Vertical Lift Doors
<br />2 Padlocks (I Daylock, I Nightlock)
<br />45-1 01 X 606 (I ong shackle as req'd)
<br />3.7.17 Group L-2
<br />Roof Hatch, Equipment Cages, Trash Compactor
<br />I Padlock
<br />45-1 01 X 606 (long shackle as req'd)
<br />17.18 Group M
<br />Roof Top Equipment Rooms
<br />3 each Hinges
<br />1270 X 4.5 X 4.5 X USP X NRP
<br />I Deadlock
<br />B16ON X 626
<br />1 Doorpull
<br />8102-6S 32D
<br />I Stop& H.O.
<br />GJ90M X 26D
<br />3.7.19 Group N
<br />3.7.20 Group R - for South Florida Building Code
<br />Exit (Panic Bar, Exit Only), with Alarm Closer
<br />W/H.O.� Doors from Stock
<br />Rooms and Elec. Equip. Rooms to Exterior (Except labeled doors-, see B-1)
<br />3 each Hinges
<br />BB 1 279 X 4.5 X 4.5 X NRP X USP
<br />I Alarmed Exit Device
<br />99EO-FX ALK-S2 X SNB X SP28
<br />LAR
<br />I Cylinder for Alarm
<br />(Furnished and installed by Publix)
<br />I Closer W/Stop, H.O.
<br />CLP8301BFH, 3321BFT, or
<br />146 1 H-CUSH X SNI3 X AL
<br />I Set Weather -Strip
<br />S88D
<br />One -Way Viewer
<br />Ives #698 Wide Angle
<br />Threshold
<br />Durable Products -
<br />Model LT-206HV - 5 1/2" Wide
<br />Automatic Door Bottoms
<br />Pemko - 4301 CPKL
<br />(Surface Mounted)
<br />3.7.21 Front Doors, Exterior Cafe Doors (Storefront)
<br />Use standard mortise or rimset cylinders supplied with store front doors as
<br />construction temporaries. Permanent cylinders furnished & installed by Publix. All
<br />other hardware by door manufacturer.
<br />3.7.22 Group P
<br />Phannacy Rolling Grille
<br />Prepare for Schlage Mortise Cylinder, Cylinder
<br />furnished and installed by Publix.
<br />3.7.23 Group Q
<br />Return Air Chase Access Doors by Milcor or Nystrom
<br />Prepare for Schlage Mortise Cylinder, Cylinder
<br />furnished and installed by Publix.
<br />End of Section 08700
<br />Section 08800
<br />Glazing
<br />1. General
<br />1. 1. Related Documents
<br />1. 1. I Drawings and general provisions of the Contract, including General and
<br />Supplementary Conditions and Division I Specification Sections, apply to this
<br />Section.
<br />1.2. Summary
<br />1.2.1 This Section includes glazin g for the following products, including those specified
<br />in other Sections where glazing requirements are specified by reference to this
<br />Section-
<br />1.2.1.1 Entrances and other doors.
<br />1.2.1.2 Storefront construction.
<br />1.2,2 Related Sections: The following sections contain requirements that relate to this
<br />Section.
<br />1.2.2.1 Division 8 Section "Mirrored Glass" for mirrored glass and glazing
<br />requirements.
<br />1.3. Definitions
<br />1.3.1 Manufacturer is used in this Section to refer to a firm that produces primary glass or
<br />fabricated glass as defined in the referenced glazing standard.
<br />1.3.2 Deterioration of Coated Glass: Defects developed from normal use that are
<br />attributed to the manufacturing process and not to causes other than glass breakage
<br />and practices for maintaining and cleaning coated glass contrary to manufacturet's
<br />directions. Defects include peeling, cracking, and other indications of deterioration
<br />in metallic coating.
<br />1.4. System Performance Requirements
<br />1.4.1 General: Provide glazing systems that are produced, fabricated, and installed to
<br />withstand normal thermal movement, wind loading, and impact loading (where
<br />applicable), without failure including loss or glass breakage attributable to the
<br />following� defective manufacture, fabrication, and installation; failure of sealants or
<br />gaskets to remain watertight and airtight-, deterioration of glazing materials, and
<br />other defects in construction.
<br />1.4.2 Glass Design� Glass thicknesses indicated on Drawings are for detailing only.
<br />Confirm glass thicknesses by analyzing Project wind loads and in-service
<br />conditions. Provide glass lites for the various size openings in the thicknesses and
<br />strengths (annealed or heat -treated) to meet or exceed the following criteria:
<br />1.4.2.1 Minimum glass thickness, nominally, of lites in exterior walls is 1/4".
<br />1.4.2.2 Tinted and heat -absorbing glass thicknesses for each tint indicated are the
<br />same throughout Project.
<br />1.4.2.3 Air Infiltration: Completed storefront systems shall have 0.02 CFM
<br />maximum allowable infiltration when tested in accordance with ASTM E
<br />283 at differential static pressure of 6.24 psf (50 mph).
<br />1.4.2.4 Water Infiltration: No uncontrolled water other than condensation on
<br />indoor face of any component when tested in accordance with ASTM E
<br />331 at test pressure differential of I 0 psf. Water test to be performed
<br />immediately after design pressure test.
<br />1.4.2.5 Wind Loads: completed storefront system withstand wind pressure loads
<br />normal to exterior wall plane indicated
<br />1.4.2.5.1 Positive Pressure: 68 psf, or as required per region for
<br />building construction.
<br />1.4-2-5.2 Negative Pressure: 86 psf, or as required per region for
<br />building construction.
<br />1.4.3 Deflection: Maximum allowable deflection in any member when tested in
<br />accordance with ASTM E 330 with allowable stress in accordance with AA
<br />Specifications for Aluminum Structures.
<br />1.4.3.1 Deflection for load carrying members not to exceed L/180.
<br />1.4.4 Thermal Movement: Provide for thermal movement caused by 180 degrees F (82.2
<br />degrees C) surface temperature, without causing loads on fasteners, reduction of
<br />performance, or detrimental effects.
<br />1.5. Submittals
<br />1.5.1 Product data for each glass product and glazing material indicated.
<br />1.5.2 Samples for verification purposes of 12-inch (300 mm) square samples of each type
<br />- of glass indicated except for clear monolithic glass products, and 12-inch (300 mm)
<br />I
<br />long samples of each color required (except black) for each type of sealant or gasket
<br />exposed to view. Install sealant or gasket sample between two strips of material
<br />representative in color of the adjoining framing system.
<br />1.5.3 Product certificates signed by glazing materials manufacturers certifying that their
<br />products comply with specified requirements.
<br />1.5.3.1 Separate certifications are not required for glazing materials bearing
<br />manufacturer's permanent labels designating type and thickness of glass,
<br />provided labels represent a quality control program of a recognized
<br />certification agency or independent testing agency acceptable to
<br />authorities having jurisdiction.
<br />1.5.4 Compatibility and adhesion test reports from sealant manufacturer indicating that
<br />glazing materials were tested for compatibility and adhesion with glazing sealants.
<br />Include sealant manufacturer's interpretation of test results relative to sealant
<br />performance and recommendations for primers and substrate preparation needed for
<br />adhesion.
<br />1.5.5 Product test reports for each type of glazing sealant and gasket indicated, evidencing
<br />compliance with requirements specified.
<br />1.5.6 Maintenance data for glass and other glazing materials to include in Operating and
<br />Maintenance Manual specified in Division 1.
<br />1.6. Quality Assurance
<br />1.6.1 Glazing Publications: Comply with published recommendations of glass product
<br />t'
<br />manufacturers and organizations below, except where more stringent requirements
<br />are indicated. Refer to these publications for glazing terms not other -wise defined in
<br />this Section or in referenced standards.
<br />1.6.1.1 FGMA Publications � "FGMA Glazing Manual."
<br />1.6.1.2 LSGA Publications: "LSGA Design Guide."
<br />1.6.1.3 SIGMA Publications: TM-3000 "Vertical Glazing Guidelines".
<br />1.6.2 Safety Glass: Products complying with ANSI Z97.1 and testing requirements of
<br />16 CFR Part 1201 for Category 11 materials.
<br />1.6.2.1 Subject to compliance with requirements, provide safety glass
<br />permanently marked with certification label of Safety Glazing
<br />Certification Council (SGCC) or other certification agency acceptable to
<br />authorities having jurisdiction.
<br />1.6.3 Glazier Qualifications: Engage an experienced glazier who has completed glazing
<br />similar in material, design, and extent to that indicated for Project with a record of
<br />successful in-service performance,
<br />1.64 Single -Source Responsibility for Glass: Obtain glass from one source for each
<br />product indicated below:
<br />1.6.4.1 Primary glass of each (ASTM C 1036) type and class indicated.
<br />1.6.4.2 Heat -treated glass of each (ASTM C 1048) condition indicated.
<br />1.6.5 Single -Source Responsibility for Glazing Accessories: Obtain glazing accessories
<br />from one source for each product and installation method indicated.
<br />1.6.6 Preconstruction Compatibility and Adhesion Testing: Submit to sealant
<br />manufacturers, samples of each glass, gasket, glazing accessory, and glass -framing
<br />member that will contact or affect glazing sealants for compatibility and adhesion
<br />testing as indicated below:
<br />1.6.6.1 Use test methods standard with sealant manufacturer to determine if
<br />priming and other specific preparation techniques are required for rapid,
<br />optimum glazing sealants adhesion to glass and glazing channel
<br />substrates.
<br />1.7. Delivery, Storage, And Handling
<br />1.7.1 Protect glazing materials to comply with mamifacturer's directions and as needed to
<br />prevent damage to glass and glazing materials from condensation, temperature
<br />changes, direct exposure to sun, or other causes.
<br />1.7.1.1 Where insulating glass units will be exposed to substantial altitude
<br />changes, comply with insulating glass fabricator's recommendations for
<br />venting and sealing to avoid bennetic seal ruptures.
<br />1.8. Project Conditions
<br />I.S.1 Environmental Conditions: Do not proceed with glazing when ambient and
<br />substrate temperature conditions are outside the limits permitted by glazing
<br />materials manufacturer or when glazing channel substrates are wet from rain, frost,
<br />condensation, or other causes.
<br />1.8.1.1 Install liquid sealants at ambient and substrate temperatures above
<br />40 deg IT (4 deg C).
<br />1.9. Warranty
<br />1.9.1 General: Warranties specified in this Article shall not deprive the Owner of other
<br />rights the Owner may have under other provisions of the Contract Documents and
<br />will be in addition to and run concurrent with other warranties made by the
<br />Contractor under requirements of the Contract Documents.
<br />1.9.2 Manufacturer's Warranty on Laminated Glass: Submit written warranty signed by
<br />insulating glass manufacturer agreeing to furnish replacements for those laminated
<br />glass units that deteriorate as defined in the "Definitions" article, f.o.b. point of
<br />manufacture, freight allowed Project site, within specified warranty period indicated
<br />below. Warranty covers only deterioration due to normal conditions of use and not
<br />to handling, installing, and cleaning practices contrary to glass manufacturer's
<br />published instructions.
<br />L9.2.1 WarrantyPeriod Manufacturer's standard but not less than 5 years after
<br />date of Substantial Completion.
<br />2. Products
<br />2.1. Manufacturers
<br />2.1.1 Available Products: Subject to compliance with requirements, products that may be
<br />incorporated in the Work include, but are not limited to, the products specified in
<br />Product Data Sheets at end of this Section.
<br />2.2. Elastomeric Glazing Sealants
<br />2.2.1 General: Provide products of type indicated, complying with the following
<br />requirements:
<br />2.2.1.1 Compatibility: Select glazing sealants and tapes of proven compatibility
<br />with other materials they will contact, including glass products, seals of
<br />insulating glass units, and glazing channel substrates, under conditions of
<br />installation and service, as demonstrated by testing and field experience.
<br />2.2.1.2 Suitability: Comply with sealant and glass manufacturer's
<br />recommendations for selecting glazing sealants and tapes that are suitable
<br />for applications indicated and conditions existing at time of installation.
<br />2.2.1.3 Colors� Provide color of exposed joint sealants to comply with the
<br />following:
<br />2.2.1.3.1 Provide selections made by Architect from manufacturer's
<br />full range of standard colors for products of type indicated.
<br />2.2.2 Elastomeric Glazing Sealant Standard: Provide manufacturer's standard chemically
<br />curing, elastomeric sealants of base polymer indicated that comply with ASTM
<br />C 920 requirements indicated on each Elastomeric Glazing Sealant Product Data
<br />Sheet at the end of this Section, including those referencing ASTM classifications
<br />for Type, Grade, Class and Uses.
<br />2.2.2.1 Additional Movement Capability: Where additional movement capability
<br />is specified in Elastomeric Glazing Sealant Product Data Sheet, provide
<br />products, when tested for adhesion and cohesion under maximum cyclic
<br />movement per ASTM C 719, with the capability to withstand the specified
<br />percentage change in the joint width existing at time of installation and
<br />remain in compliance with other requirements of ASTM C 920 for uses
<br />indicated.
<br />1
<br />23. Glazing Gaskets
<br />2.3.1 Lock -Strip Gaskets: Neoprene extrusions in size and shape indicated, fabricated
<br />into frames with molded comer units and zipper lock strips, complying with ASTM
<br />C 542, black.
<br />2.3.2 Dense Compression Gaskets: Molded or extruded gaskets of material indicated
<br />below, complying with standards referenced with name of elastomer indicated
<br />below, and of profile and hardness required to maintain watertight seal:
<br />Neoprene, ASTM C 864.
<br />EPDM, ASTM C 864.
<br />Silicone, ASTM C 11 15.
<br />Thermoplastic polyol efin rubber, ASTM C I 1 15.
<br />Any material indicated above.
<br />2.3.3 Soft Compression Gaskets: Extruded or molded closed -cell, integral -skinned
<br />gaskets of material indicated below, complying with ASTM C 509, Type 11, black,
<br />and of profile and hardness required to maintain watertight seal:
<br />Neoprene,
<br />EPDM.
<br />Silicone.
<br />Thermoplastic polyolefin rubber.
<br />Any material indicated above,
<br />2.3.4 Manufacturers: Subject to compliance with requirements, provide products by one
<br />of the following companies.
<br />2.341 Lock -Strip Gaskets:
<br />Stanlock Div., Griffith Rubber Mills.
<br />2.3.4.2 Preformed Gaskets:
<br />Advanced Elastomer Systems, L.P.
<br />Schnee -Morehead, Inc.
<br />Tremco, Inc.
<br />2.4. Miscellaneous Glazing Materials
<br />2.4.1 General: Provide products of material, size, and shape complying with referenced
<br />glazing standard, requirements of manufacturers of glass and other glazing materials
<br />involved for glazing application indicated, and with a proven record of compatibility
<br />with surfaces contacted in installation.
<br />2.4.2 Cleaners, Primers and Sealers: Type recommended by sealant or gasket
<br />manufacturer.
<br />2.4.3 Setting Blocks: Elastomeric material with a Shore A durometer hardness of 85 plus
<br />or minus 5.
<br />2.4.4 Spacers: Elastomeric blocks or continuous extrusions with a Shore A durometer
<br />hardness required by glass manufacturer to maintain glass lites in place for
<br />installation indicated.
<br />2.4.5 Edge Blocks: Elastomeric material of hardness needed to limit glass lateral
<br />movement (side- walking).
<br />C
<br />2.4.6 Plastic Foam Joint Fillers: Preformed, compressible, resilient, nonstaining,
<br />nonextruding, nonoutgassing, strips of closed -cell plastic foam of density, size, and
<br />shape to control sealant depth and otherwise contribute to produce optimum sealant
<br />performance.
<br />2.4.7 Perimeter Insulation for Fire -Resistive Glazing: Identical to product used in test
<br />assembly to obtain fire -resistive rating.
<br />2.5. Fabrication of Glass and Other Glazing Products
<br />2.5.1 Fabricate glass and other glazing products in sizes required to glaze openings
<br />indicated for Project, with edge and face clearances, edge and surface conditions,
<br />and bite complying with recommendations of product manufacturer and referenced
<br />glazing standard as required to comply with system performance requirements.
<br />2.5.2 Clean cut or flat grind vertical edges of butt -glazed monolithic lites in a manner that
<br />produces square edges with slight kerfs at junctions with indoor and outdoor faces.
<br />3. Execution
<br />3.1. Examination
<br />3.1.1 Examine glass framing, with glazier present, for compliance with the following�
<br />3.1.1.1 Manufacturing and installation tolerances, including those for size,
<br />squareness, offsets at corners,
<br />3.1.1.2 Presence and functioning of weep system.
<br />3.1.1.3 Minimum required face or edge clearances.
<br />3.1.1.4 Effective sealing between joints of glass -framing members.
<br />3.1.2 Do not proceed with glazing until unsatisfactory conditions have been corrected.
<br />3.2. Preparation
<br />3.2.1 Clean glazing channels and other framing members receiving glass immediately
<br />before glazing. Remove coatings that are not firmly bonded to substrates.
<br />3.3. Glazing, General
<br />3.3.1 Comply with combined recommendations of manufacturers of glass, sealants,
<br />gaskets, and other glazing materials, except where more stringent requirements are
<br />indicated, including those in referenced glazing publications.
<br />3.3.2 Glazing channel dimensions as indicated on Drawings provide necessary bite on
<br />glass, minimum edge and face clearances, and adequate sealant thicknesses, with
<br />reasonable tolerances. Adjust as required by Project conditions during installation.
<br />3.3.3 Protect glass from edge damage during handling and installation as follows:
<br />3.3.3.1 Use a rolling block in rotating glass units to prevent damage to glass
<br />comers. Do not impact glass with metal framing. Use suction cups to
<br />shift glass units within openings; do not raise or drift glass with a pry bar.
<br />Rotate glass lites with flares or bevels on bottom horizontal edges so
<br />edges are located at top of opening, unless other -wise indicated by
<br />manufacturer's label.
<br />3.3.3.2 Remove damaged glass from Project site and legally dispose of off site.
<br />Damaged glass is glass with edge damage or other imperfections that,
<br />when installed, weaken glass and impair performance and appearance.
<br />3.3.4 Apply primers to joint surfaces where required for adhesion of sealants, as
<br />determined by preconstruction seat ant -sub strate testing.
<br />3.3.5 Install elastomeric setting blocks in sill rabbets, sized and located to comply with
<br />referenced glazing standard, unless otherwise required by glass manufacturer. Set
<br />blocks in thin course of compatible sealant suitable for heel bead.
<br />3.3.6 Do not exceed edge pressures stipulated by glass manufacturers for installing glass
<br />lites.
<br />3.3.7 Provide spacers for glass sizes larger than 50 united inches (I 250 mm) (length plus
<br />height) as follows:
<br />3.3.7.1 Locate spacers inside, outside, and directly opposite each other. Install
<br />correct size and spacing to preserve required face clearances, except
<br />where gaskets and glazing tapes are used that have demonstrated ability to
<br />maintain required face clearances and comply with system performance
<br />requirements.
<br />3.3.7.2 Provide 1/8-inch (3 mm) minimum bite of spacers on glass and use
<br />thickness equal to sealant width. With glazing tape, use thickness slightly
<br />less than final compressed thickness of tape.
<br />3.3.8 Provide edge blocking to comply with requirements of referenced glazing
<br />publications, unless otherwise required by glass manufacturer.
<br />3.3.9 Set glass lites in each series with uniform pattern, draw, bow, and similar
<br />characteristics.
<br />3.3.10 Where wedge-shaped gaskets are driven into one side of channel to pressurize
<br />sealant or gasket on opposite side, provide adequate anchorage so gasket cannot
<br />walk out when installation is subjected to movement.
<br />3.3.11 Square cut wedge-shaped gaskets at comers and install gaskets in manner
<br />recommended by gasket manufacturer to prevent comers from pulling away� seal
<br />comerjoints and butt joints with sealant recommended by gasket manufacturer.
<br />3.4. Tape Glazing
<br />3.4.1 Position tapes on fixed stops so that when compressed by glass their exposed edges
<br />are flush with or protrude slightly above sightline of stops.
<br />3.4.2 Install tapes continuously but not in one continuous length. Do not stretch tapes to
<br />make them fit opening.
<br />3.4.3 Where framing joints are vertical, cover thesejoints by applying tapes to heads and
<br />sills first and then tojambs. Where framing joints are horizontal, cover these joints
<br />by applying tapes to jambs and then to heads and sills.
<br />3.4.4 Placejoints in tapes at comers of opening with adjoining lengths butted together,
<br />not lapped. Seal joints in tapes with compatible sealant approved by tape
<br />manufacturer.
<br />3.4.5 Do not remove release paper from tape until just before each lite is installed.
<br />3.4.6 Apply heel bead of elastomeric sealant.
<br />3.4.7 Center glass lites in openings on setting blocks and press firmly against tape by
<br />inserting dense compression gaskets formed and installed to lock in place against
<br />faces of removable stops. Start gasket applications at corners and work toward
<br />centers of openings.
<br />3.4�8 Apply cap bead of elastomeric sealant overexposed edge of tape.
<br />3.5. Gasket Glazing (Dry)
<br />3.5.1 Fabricate compression gaskets in lengths recommended by gasket manufacturer to
<br />fit openings exactly, with stretch allowance during installation.
<br />3.5.2 Secure compression gaskets in place with joints located at corners to compress
<br />gaskets producing a weathertight seal without developing bending stresses in glass.
<br />Seal gasket joints with sealant recommended by gasket manufacturer.
<br />3.5.3 Install gaskets so they protrude past face of glazing stops.
<br />3.6. Sealant Glazing (Wet)
<br />3.6.1 Install continuous spacers between glass lites and glazing stops to maintain glass
<br />face clearances and to prevent sealant from extruding into glass channel weep
<br />systems until sealants cure. Secure spacers in place and in position to control depth
<br />of installed sealant relative to edge clearance for optimum sealant performance.
<br />3.6.2 Force sealants into glazing channels to eliminate voids and to ensure complete
<br />wetting or bond of sealant to glass and channel surfaces.
<br />3.6.3 Tool exposed surfaces of sealants to provide a substantial wash away from glass.
<br />Install pressurized gaskets to protrude slightly out of channel to eliminate dirt and
<br />moisture pockets-
<br />3�7. Lock -strip Gasket Glazing
<br />3.7.1 Comply with ASTM C 716 and gasket manufacturer's printed recommendations.
<br />Provide supplementary wet seal and weep system unless otherwise indicated.
<br />3.8. Protection and Cleaning
<br />3.8.1 Protect exterior glass from breakage immediately after installation by attaching
<br />crossed streamers to framing held away from glass. Do not apply markers to glass
<br />surface. Remove nonpermanent labels, and clean surfaces.
<br />3.8.2 Protect glass from contact with contaminating substances resulting from
<br />construction operations including weld splatter. If, despite such protection,
<br />contaminating substances do come into contact with glass, remove them
<br />immediately as recommended by glass manufacturer.
<br />3.8.3 Examine glass surfaces adjacent to or below exterior concrete and other masonry
<br />surfaces at frequent intervals during construction, but not less than once a month, for
<br />build-up of dirt, scum, alkali deposits, or stains, and remove as recommended by
<br />glass manufacturer.
<br />3.8.4 Remove and replace glass that is broken, chipped, cracked, abraded, or damaged in
<br />any way, including natural causes, accidents and vandalism, during construction
<br />period.
<br />3.8.5 Wash glass on both faces in each area of Project not more than 4 days prior to date
<br />scheduled for inspections that establish date of Substantial Completion. Wash glass
<br />as recommended by glass manufacturer.
<br />4. Product Data Sheet I - Scaled Insulated Panels
<br />4. 1 � Insulating Panel Designation:
<br />4.2. Kind of Insulating Panel per ASTM C 1172: Kind LT (lites of fully tempered Type I
<br />glass).
<br />4.2.1 Tinted Outer Lite: Class 2 (Low "E" Coating) float glass with a tint color to be
<br />chosen by the Owner from the manufacturer's standard color samples.
<br />4.3, Approved Product:
<br />PPG "Herculite"
<br />End of Section 08800
<br />1. General
<br />(Not Used)
<br />Section 09250
<br />Gypsum Board
<br />2. Products
<br />2.1. Manufacturer. All materials shall be products of one manufacturer.
<br />2.2. Materials:
<br />2.2.1 Drywall.
<br />2.2.1.1 General use drywall: ASTM C36.
<br />2.2.1.2 Fire Retardant Drywall: ASTM C36, Type X
<br />2.2.1.3 Manufacturers:
<br />Domtar Gypsum
<br />Georgia-Pacific Corp.
<br />National Gypsum Co.
<br />Temple-Inland Forest Products Corp.
<br />United States Gypsum Co.
<br />2.2.2 Tile Backer Board (Use instead of MR wallboard): Georgia Pacific Dens -Shield Tile
<br />Backer.
<br />2.2.3 Exterior Insulation System Backer Board: USG 5/8" thick water resistant exterior
<br />gypsum sheathing board. Install Dens -Deck at canopy roofs and awning roofs.
<br />2.2.4 Accessories:
<br />2.14.1 Joint Reinforcing Tape shall be perforated or sparked. Joint compound
<br />shall be ready mixed.
<br />2.2.4.2 Corner Beads, Casing Beads and Trim shall be galvanized steel.
<br />2.2.5 Drywall Ceiling Suspension System� 650 Drywall Furring System as manufactured
<br />by Chicago Metallic or equal as approved by the Architect.
<br />2.2.5.1 Furring Runners and Tees shall be 1 1/2" high double web 0.020 electro-
<br />galvanized steel with 1 3/8" flange face. Runners shall be 12' long with
<br />reversible coupling ends for continuous splicing.
<br />2.2.5.2 Wall Track shall be 451 1 0 track made of 0. 020 electro-galvanized steel.
<br />2.2.6 Steel Studs:
<br />2.2.6.1 Galvanized screwable channel type studs of specified size, complying
<br />with ASTM C645, minimum 20 ga at all interior locations. Refer to
<br />structural design drawings for exterior locations.
<br />2.2.6.2 Manufacturer:
<br />Milcor Division of Inryco, Inc.
<br />U.S. Gypsum Co.
<br />Dale/Incor
<br />Unimast (Usg)
<br />2.2.6.3 Form from steel ASTM A446, Grade A, with a minimum yield of 33,000
<br />psi.
<br />2.2.7 Drywall Screws: ASTM C645.
<br />2.3. Backing for drywall at outside curve applications: A-C INT-APA with exterior glue, 1/8"
<br />thickness.
<br />3. Execution
<br />3.1. Ceiling
<br />3.1.1 Install wall track level at specified ceiling height around entire perimeter.
<br />3.1.2 Furring runners shall be directly suspended and leveled on 48" centers by not less
<br />than 12 gauge galvanized steel wire spaced not more than 48" on center along the
<br />I'D
<br />main runner. (for special module sizes follow same procedures with on center
<br />spacing of runners adjusted to tee width.)
<br />3.1.3 Furring tees shall be spaced 16" on center along the main runners.
<br />3.1.4 Fit furring runner and tee ends into the wall track at all perimeters.
<br />3,1.5 Drywall panels shall be screw attached at 8" intervals to all furring runners, tees,
<br />and wall track with the long dimension paralleling the furring runners in all possible
<br />instances. Deflection of components not to exceed 1/360 of the span.
<br />3.1.6 In areas where fixtures or other accessories are placed in or on the grid components,
<br />12 gauge hanger wires are to be suspended at each comer of the fixture or accessory
<br />to distribute the load evenly.
<br />3.2. Walls
<br />'
<br />3.2.1 Steel Studs: 16" on center.
<br />3.2.2 Panels shall be screwed to steel studs with bugle head dry wall screws of length as
<br />recommended by manufacturer.
<br />3.2.3 Insulate walls around Meat Cutting, Packaging Room, Employee Lounge,
<br />Manager's Office, Rest Rooms and as indicated on Drawings with 3 1-2" batt
<br />insulation.
<br />3.2.4 Axially loaded studs shall be installed in a manner which will assure that ends of the
<br />studs are positioned against the inside track web, prior to stud and track attachment.
<br />3.2.5 Studs shall be plumbed, aligned and securely attached to the flanges orwebs ofboth
<br />upper and lower tracks.
<br />3.2.6 Jack studs or cripples shall be installed above window and door heads, at free
<br />standing stair rails, and elsewhere to furnish support, and shall be securely attached
<br />to supporting members.
<br />3.2.7 Wall stud bridging shall be attached in a manner to prevent stud rotation. Bridging
<br />rows shall be spaced according to the following schedule: walls up to 10' 0" height:
<br />one row at mid -height; walls exceeding I 0'-O": bridging rows spaced not to exceed
<br />5'-O" on -center.
<br />3.2.8 Provide 7/8" 20 gauge galvanized steel drywall furring channels vertically at 16"
<br />o.c. for all paneled walls on masonry and others as required.
<br />3.3. Walls and Ceilings
<br />3.3.1 Steel stud framing components may be pre -assembled into panels prior to erecting.
<br />Prefabricated panels shall be square with components attached in a manner as to
<br />prevent racking.
<br />3.3.2 All framing components shall be set squarely for attachment to perpendicular
<br />members, or as required for an angular fit against abutting members. Members shall
<br />be held positively in place until properly fastened.
<br />3.3.3 A uniformly thin layer ofjoint compound shall be applied overjoints approximately
<br />4" wide. The tape centered overjoint and imbedded into compound leaving
<br />sufficient joint compound under tape to provide proper bond. Ceiling and wall
<br />angles and inside comer angles shall be reinforced with tape folded to conform to
<br />the angle and imbedded in the compound.
<br />3.3.4 Sand between coats.
<br />3.3.5 After compound is thoroughly dry, the tape shall be covered with another coat of
<br />joint compound spread over the tape and 3" each side of tape, and feathered out at
<br />edge, After thoroughly dry, apply another coat with slight, uniform crown over the
<br />joint. this coat shall be smooth with edges feathered approximately 3" beyond
<br />preceding coat.
<br />3.3.6 Coat corners, and nail or screw heads additionally as per manufacturers
<br />specifications.
<br />3.3.7 Install J-mold at ceiling and wall juncture where required.
<br />3.3.8 Entire areas shall be installed neatly and ready to receive finish as scheduled. All
<br />studs shall have drywall to the top of the plate for fire and rodent protection.
<br />'
<br />.3.3.9 Control Joints� In ceiling, install expandable control joints as recommended by
<br />manufacturer, at maximum 40' on center.
<br />3.4. Tile Backer Board
<br />3.4.1 Use at all locations where wall finish is tile.
<br />3.4.2 Use behind all refrigerated cases to a height of 4'-O 1/2". start at 1/2" above finished
<br />floor.
<br />3.4.3 Install adjacent to all walk-in coolers and freezers. Height: above the top of the unit.
<br />3.5. Curved Suspended Walls:
<br />3.5.1 Outside curves 10'-O" radius or less: Form curve with metal studs 8" oc be -inning
<br />C
<br />2'-O" into straight portion of wall, Thoroughly soak and apply two layers 1/8"
<br />plywood to metal studs allowing first layer to dry before application of second.
<br />Apply 1/4" drywall to plywood substrate with drywall adhesive, long dimension
<br />horizontal, Wet drywall as necessary to obtain smooth curve with no flats.
<br />3.5.2 Outside curves radius greater than I 0'-O": Form curve with metal studs 8" oc
<br />beginning 2'-O" into straight portion of wall. Apply 5/8" drywall to metal studs with
<br />drywall adhesive, long dimension horizontal. Wet drywall as necessary to obtain
<br />smooth curve with no flats.
<br />3.5.3 Inside curves radius greater than 10'-O": Form curve with metal studs I'-O" oc
<br />beginning 2'-O" into straight portion of wall. Apply 5/8" drywall to metal studs with
<br />drywall adhesive, long dimension horizontal. Wet drywall as necessary to obtain
<br />smooth curve with no flats.
<br />End of Section 09250
<br />Section 09300
<br />Hard Tile
<br />1. General
<br />1. 1. Extra Stock: Upon completion of the work of this Section, deliver to Publix additional tile
<br />and trim shapes of each type, color, pattern, and size used in the work, for Publix' use in
<br />replacement and maintenance, at the rate of three percent of the amount used in the work,
<br />packaged securely to prevent damage, and clearly labeled with identification of project,
<br />type of tile, etc.
<br />1.2. Warranties: All tile work shall be guaranteed for workmanship for a period of two (2) years.
<br />Any work found to be defective during that time shall be replaced at no cost to the Owner.
<br />2. Products
<br />2.1. Quarry Tile Floor and Base:
<br />2.1.1 Manufacturer, series, finish, color, and size as indicated on floor finish plan. Provide
<br />matching base tile type Q3566, with type QB3566 inside comers and type QC3566
<br />outside corners, where base is flush with ceramic tile wall. Provide matching base
<br />tile type Q3565, with type QB3565 inside corners and type QC3565 outside corners,
<br />where base adjoins other wall finishes.
<br />2.1.2 Expansion Joint Sealer: Polyurethane sealant with primer.
<br />Tremco Trembond Primer with HPL sealant
<br />2.2. Ceramic Tile Walls and Wainscots: Manufacturer, series, finish, color, and size as indicated
<br />on room finish schedule.
<br />2.3. Epoxy Setting and Grouting Compounds:
<br />2.3.1 Setting/Grouting Materials:
<br />Master Builders (I -800-226-0700) "Chemset" setting compound for
<br />setting, "Chemset 1880" for grouting.
<br />Termar "Terraset" for setting, "Terragrout" for grouting.
<br />Summitville S400
<br />Laticrete "Latapoxy 300" for setting, "Latapoxy SP-100" for grouting.
<br />American Olean A06000
<br />2.3.2 Grout color as indicated on floor finish plan; if no color is indicated, color as
<br />selected by Publix' Architect, from manufacturers stand and color samples.
<br />2.4. Sanded Latex Portland Cement Grout
<br />2.4.1 Provide a commercially prepared mixture of portland cement, sand, and other
<br />ingredients producing a water-resistant, dense, uniformly colored material, mixed
<br />with an acrylic latex additive by the same manufacturer.
<br />2.4.2 Color as indicated on floor finish plan or interior finish elevations, if no color is
<br />indicated, color as selected by Publix' Architect.
<br />2.5. Thin Set Mortar� Laticrete 44237 thin -set bonding mortar additive with Laticrete #211
<br />Crete filler powder
<br />2.6. Organic Adhesive
<br />2.6.1 Provide a prepared organic material, ready to use with no further addition of liquid
<br />or powder, which cures or sets by evaporation.
<br />2.6.2 Comply with ANSI A136.1, using type I (for exposure to prolonged water
<br />presence).
<br />2.7. Sealants: One or two part urethane. Use type designed for application intended, color as
<br />selected by Architect.
<br />3. Execution
<br />3.1. General: All applicators and field personnel shall be fully trained and familiar with
<br />manufacturers' application procedures.
<br />3.2. Quarry Tile Sub -Setting Bed: Areas to receive quarry tile shall receive a sub -setting bed,
<br />which shall consist of 24 shovels of sand per one bag of portland cement, shall be free of
<br />foreign matter, and shall be dried before file is applied to maximum of 16% moisture
<br />content.
<br />3.3. Quarry Tile and Base, and exterior quary tile decoration trim.
<br />33.1 Set and grout all quarry tile floors and base with epoxy, Set and grout in two
<br />separate operations, and in accordance with manufacturer's specification and
<br />recommendations.
<br />3.3.2 Lay tile in a straightjoint pattern, each direction, with a 1/4" joint. Align floor and
<br />basejoints.
<br />3.3.3 Grout shall be level with the surface of the tile, with no sharp edges of the tile
<br />showing.
<br />3.3.4 Cut quarry tile as required to provide a 1/4" control joint directly above slab
<br />construction joints. Prime sides of joint width. Seal control joint with polyurethane
<br />sealant to 1/4" depth, backed with closed -cell foam.
<br />3.3.5 Slope all tile to drains, as shown on Drawings. Set all tile flush with tops of floor
<br />drains and adjacent finished floors.
<br />3.3,6 All walls adjoining floor shall receive matching quarry tile base, regardless of type
<br />finish on walls. Align all basejoints with floorjoints.
<br />3.3.7 Ensure that base has a solid bed of epoxy where it makes contact with the wall, and
<br />that there are no void areas behind tile and at transition with floor.
<br />3.4. Marble or Granite Sills
<br />3.4.1 Set by experienced granite craftsmen who have a minimum of three (3) years
<br />experience in the trade, and in accordance with the Marble Institute of America
<br />(M.I.A.) Installation Procedures Manual.
<br />3.4.2 Seal Joints with appropriate sealant.
<br />3.4.3 Coordinate and cooperate with store front sash installer.
<br />3.5. Ceramic Wall Tile on Masonry Substrate
<br />3.5A Thin -set with mortar and grout with sanded latex portland cement grout, both in
<br />accordance with manufacturer's specifications and recommendations.
<br />3.5.2 Set flush with adjacent base, lay in a straightjoint pattern each direction, with a
<br />joint width of 1/4" or as established by manufacturer's sheet.
<br />3.5.3 Grout shall be level with the surface of the tile, with no sharp edges of the tile
<br />showing,
<br />3.6. Ceramic Tile on Backer Board
<br />3.6.1 Set on moisture -resistant backer board with organic adhesive, grout with sanded
<br />latex portland cement grout, both in accordance with manufacturer's specifications
<br />and recommendations.
<br />3.6.2 Set flush with adjacent base; lay in a straight joint pattern each direction, with a
<br />joint width of 1/4" or as established by manufacturer's tile sheet.
<br />3.6.3 Grout shall be level with the surface of the tile, with no sharp edges of the tile
<br />showing.
<br />3.7. Exterior Ceramic Tile� If this project is to receive exterior tile set on a vertical surface, see
<br />Contract Documents, The tile, setting method, pattern and grout shall be approved in
<br />writing by Publix' Architect.
<br />End Of Section 09300
<br />Section 09410
<br />Portland Cement Terrazzo
<br />1. General
<br />1. 1. Applicators: Applicator shall be approved by Publix Architect. Before the bid, proof of
<br />experience in work of similar scope will be required.
<br />1.2. Job Conditions:
<br />1.2.1 Do not begin application until roofing operations have been completed.
<br />1.2.2 Substrate: Applicator shall verify slab meets standards of slab quality as specified; if
<br />it does not then he shall notify Publix Architect before work is started.
<br />1.2.3 Application of terrazzo shall constitute evidence of acceptance of slab.
<br />1.2.4 Protection of installed work shall begin immediately upon completion of each part.
<br />Do not allow materials which can mar or stain to come into contact with floor -
<br />Protect floor from wheeled traffic and other activities which might cause permanent
<br />damage.
<br />1.2.5 CLEAN FLOOR DAILY.
<br />1.3. Warranty: All terrazzo work shall be guaranteed against defects in material and
<br />workmanship for a period of two years. Work found to be defective during that time will be
<br />replaced at no cost to the Owner. A written warranty shall be provided.
<br />2. Products
<br />2.1. Materials
<br />2.1.1 Portland Cement, Type 1, white.
<br />2.1.2 Divider Strips� 5/8" x 1/8" zinc heavy top "T".
<br />2.1.3 Expansion Stripi 1/8" wide white neoprene plastic filler, in a 5/8" high zinc "T"
<br />strip located as shown on Drawings.
<br />2.1.4 Marble Chip colors and percentages are shown on drawings. All chips are to be 50%
<br />91 and 50% 42 sizing.
<br />2.1.5 Sealer: As directed by Publix' Representative. Apply two (2) coats, minimum four
<br />(4) hours between coats� dry and clean.
<br />3. Execution
<br />3.1. Installation
<br />3.1.1 All Terrazzo shall be mixed at a ratio of two bags of marble chips (200 lbs.) to one
<br />94 lb. bag of white cement,
<br />3.1.2 Strips� Set with laticrete #4237.
<br />3.1.3 Prime sub -floor with pure white neat cement and pour topping over wet primer.
<br />3.1.4 Pour terrazzo topping to a minimum 5/8" coating insuring all mix is above the
<br />terrazzo strip level.
<br />3.1.5 Compact wet topping with terrazzo rollers per NTMA specifications.
<br />3.1.6 Seed surface with 42 chips only of same color and percentages as in base coat, (Use
<br />of white chips and base coat with coloring achieved in finished coat will not be
<br />accepted.)
<br />3.1.7 Rough grind floor with 24 grit terrazzo grinding stones. Use 80 grit stones for polish
<br />phases followed by 120 grit for final polish. .
<br />3.1.8 Seal floor with 2 coats of terrazzo sealer. Clean floor before applying sealer,
<br />otherwise the floor shall be stripped, cleaned and re -sealed. Machine buff each coat
<br />after installation.
<br />3.1.9 Terrazzo finish shall show a minimum of 70% marble aggregate finish, and be
<br />consistent with marble chip throughout the entire surface area, even under cases and
<br />against walls.
<br />End of Section 09410
<br />Section 09500
<br />Ceiling Systems
<br />1. General
<br />1. 1. Custom Colors � Where custom colors of ceiling panels are specified, it is assumed that the
<br />quantity required for use will exceed the amount of material needed for a stock run by panel
<br />manufacturer. If this condition is not met, and there is an up -charge for custom colors,
<br />notify Publix Architect.
<br />1.2. Extra Stock: Provide Publix an extra stock of one percent of each type of ceiling panel
<br />installed, maximum ten panels, minimum three panels, each type packaged to prevent
<br />damage and clearly identified.
<br />2. Products
<br />2.1. Suspension Systems:
<br />2.1.1 Where ceiling panels are used: 15/16" exposed double -web tee conforming to
<br />ASTM C635 Intermediate -Duty classification standards. Cross -tees shall also
<br />comply with Intermediate -Duty (12 lb/If) standards, and shall have stab -type
<br />stepped (i.e. overriding) ends.
<br />-
<br />2.1.2 Wall molding shall be angle with 7/8" legs. System color shall be flat white for sales
<br />area and U.S. G. color silvertone 052 in the Bakery Sales and Produce Sales areas.
<br />2.13 Acceptable Systems:
<br />Armstrong Prelude MIL 15/16" exposed tee system, aluminum caps and
<br />stepped end cross tees.
<br />USG Interiors, Inc. Donn DXLA aluminum caps and stepped end cross
<br />tees for sales and office areas.
<br />USG Interiors, Inc. Donn DXLA aluminum caps and stepped end cross
<br />tees - U.S.G. color silvertone 052 in the Bakery Sales and Produce Sales
<br />areas.
<br />2.2. Utility Grid System:
<br />2.2-1 Main Runners Boston Retail Products "Power Track," spaced as shown on the
<br />Drawings. Factory paint all surfaces custom color as selected by Publix Architect.
<br />2.12 Grid: As above, but punched T-O" oc only. paint all surfaces custom color as
<br />selected by Publix Architect.
<br />2.2.3 Edge Trim: 5/8" high x 9/16" legs, with connectors for grid system capable of
<br />receiving intersecting tees at any angle, and splice plates to form flush butt joints
<br />where edge trim ends meet. Splice plates shall provide tight fliction fit or be secured
<br />with set screws. Factory paint all surfaces custom color as selected by Publix
<br />Architect. Acceptable systems:
<br />USG Interiors "Compasso" System
<br />Chicago Metallic Suspended Perimeter Trim System
<br />Gordon Architectural Aluminum Specialties, Inc. "Contura"
<br />2.3. Space Frame Grid System
<br />2.3.1 Main Beams: 12" triangular three-dimensional truss beams fabricated from I" dia.
<br />18 ga. steel tubing with. 1 87" steel wire webbing forming 12" (nom.) panels.
<br />2.3.2 Components: Vertex down style X's and Tees, with true 90 deg. corners.
<br />2.3.3 Beam End Pieces: Tubular ends at free ends, where ends are attached to walls,
<br />provide appropriate brackets and fasteners.
<br />2.3.4 Adjustable Brackets:
<br />2.3.4.1 Fabricate from tubular steel with telescoping anns, sized appropriately for
<br />span required
<br />2.3.4.2 Secure with thumb -turn set screws. Provide nuts for set screws welded to
<br />outer tube.
<br />2.3.4.3 End Hooks: Non scratching with adjustable angle connection to bracket.
<br />2.3.5 Connectors: Cast aluminum twist connectors.
<br />2.3.6 Accessories: Hangers, steel supports, threaded rods, cable, u-bolts, etc. as required.
<br />2.3.7 Acceptable Product:
<br />Boston Retail Products, Boston Beam Decorative Space Frame.
<br />2.3.8 Utilities: Coordinate with electrical and plumbing service requirements.
<br />2.4. Acoustical Tile
<br />2.4.1 CS-2A Acoustical Tile shall be one of the following:
<br />Armstrong Fine Fissured RH90, 24" x 48" x 5/8" square -cut edge,
<br />Fireguard (UL Label), color: white. Model 1830.
<br />Celotex Hytone Vantage 10, 24" x 48" x 5/8", square -cut edge,
<br />Protectone (UL Label)� color: white. Model PVN- 197.
<br />U.S.G.Interiors, Inc. Radar Climaplus, 24" x 48" x 5/8", square -cut edge,
<br />Firecode� color: white. Model 92410.
<br />2.4.2 CS-213 Acoustical Tile shall be one of the following,
<br />Armstrontg Fine Fissured RH90, 24" x 24" x 5/8" square cut -edge,
<br />Fireguard (UL Label), Color- White. Model 183 1.
<br />Celotex Hytone Vantage 10, 24" x 24" x 5/8" square cut edge, Protectone
<br />(UL Label): White. Model PVN-157.
<br />U.S.G. Interiors, Inc. Radar Climaplus, 24" x 24" x 5/8", square -cut edge,
<br />Class A; Color: White. Model 42210,
<br />2.4.3 CS-3A Acoustical Tile shall be one of the following�
<br />Armstrong Fine Fissured RH90, 24" x 48" x 5/8", reveal edge, Fireguard
<br />(UL Label), color� white. Model 1834.
<br />Celotex Hytone Vantage 10, 24" x 48" x 5/8", reveal edge, Protectone
<br />PVN-154 (contractor to provide 2' x 2' grid in base bid as 2' x 4' tile not
<br />available).
<br />U.S.G.Interiors, Inc. Radar Climaplus, 24" x 48" x 5/8", reveal edge,
<br />Class A, color: white. Model 42420.
<br />2.4.4 CS-313 Acoustical Tile shall be one of the following:
<br />Armstrong Fine Fissured RH90, 24" x 24" x 5/8" reveal edge, fireguard
<br />(LTL Label), Color: White. Model 1732.
<br />U.S.G. Interiors, Inc. Radar Climaplus, 24" x 24" x 5/8", reveal edge,
<br />Class A, Color: White. Model 7�2220.
<br />2.4.5 CS-5 Vinyt-Faced Gypsum Panels 24" x 48" x 1/2" with 2-mil stipple -pattern
<br />embossed white vinyl laminated to one side, surface burning characteristics - non-
<br />combustible, class A, as follows:
<br />Ann strong Duracl ad
<br />Capaul Corp. Vinylrock 'x' Gypsum Ceiling Panels
<br />Celotex Vinyltone Gypsum Protectone
<br />Gold Bond Building Products Gridstone
<br />U. S.G. Interiors, Inc. Gypsum Ceiling Panels
<br />2.4.6 CS-6 Acoustical Tile shall be one of the following:
<br />U.S.G. Interiors, Inc. Auratone, Omni Face Cuts, Radar Illusion, thirty
<br />two/6, 24" x 48" x 3/4", reveal edge, Class A, color - Silvertone 052.
<br />Model #2862.
<br />Celotex Baroque Customline Designer Series, thirty two/6", 24" x 48" x
<br />3/4", revel edge, Protectone; color - Platinum I Model BQCL-326.
<br />2.5. Thermal Insulation: Shall be insultated with R-19 or R-12 faced glass fiber insulation
<br />(locations to be as indicated in RoomFinish Schedule). (Insulation to be roll batt installed
<br />perpendicular to long dimension of tile.)
<br />2.6. Acoustic Insulation The 6" fiber insulation locations to be as indicated in room finish
<br />schedule. (Insulation to be roll batt installed perpendicular to long dimension of tile.)
<br />2.7. Openwork Systems, Utility Grid, and Space Frame Grid System Shop Fabrication and
<br />Finishin&
<br />2.7.1 Shop Fabrication, General:
<br />2.7.1.1 Perform shop fabrication to the greatest extent possible.
<br />2.7.1.2 Design of systems shall allow all welding operations to be completed in
<br />the fabrication shop.
<br />2.7.1.3 Design of systems shall allow installation of utility runs in a manner
<br />which provides a neat, finished appearance.
<br />2.7.2 Space Frame Grid System
<br />2.7.2.1 Fabricate beams to longest lengths possible. Minimize field connections
<br />except where system components are used to join beams.
<br />2.7.2.2 Weld all joints where possible. Exposed fasteners are not permitted except
<br />where needed for field connections.
<br />2.7.2.3 Design connections to be installed without exposed fasteners to the
<br />greatest extent possible.
<br />2.7.3 Edge Trim Shop Forming:
<br />2.73.1 Form edge trim to lines and radii shown on the Drawings.
<br />2.7.3.2 Lay out formed pieces so that splices occur at points of inflection of
<br />Curved lines where possible, with as few splices as possible on outside
<br />curves.
<br />2.7.3.3 On outside curves, cut legs so splices are butt joined flush at the face of
<br />the Trim.
<br />2.7.4 Shop Painting: 1
<br />2.7.4.1 Apply manufacturer's standard baked -on enamel to all surfaces, custom
<br />color as selected by Publix Architect.
<br />2.7.4.2 Coat all accessories such as splice plates, etc. to match edge trim color.
<br />2.7.4.3 Wrap or pack all painted items to protect them from scratching or other
<br />damage during shipment. Provide temporary protection for painted
<br />surfaces (i.e. peel -off film) to be removed only after all work adjacent to
<br />trim is in place.
<br />3. Execution
<br />3.1. Suspension System
<br />3.1.1 The exposed grid system shall be installed in accordance with ASTM C636.
<br />Deflection of any component shall not exceed 1/360 of the span. Suspension
<br />systems shall be installed level and square by methods according to manufacturer's
<br />specification and firmly braced to hold position and to carry weight of fixtures.
<br />Refer to Drawings.
<br />3.1.2 Perimeter angle molding shall be installed at the specified ceiling height at the
<br />intersection of the suspended ceiling and all vertical surfaces.
<br />3.1.3 Cooperate with other trades as required for fixture installation to see that proper
<br />support and spacing is obtained.
<br />3.1.4 Provide two #10 safety wires per each new and noncompliant existing metal halide
<br />and fluorescent fixture, attached to joists at proper location as coordinated with
<br />electrical contractor. (Electrical Contractor shall attach to fixture.).
<br />3.2. Lay -In Panels
<br />3.2.1 Acoustical tile shall be installed under temperature and humidity conditions closely
<br />approximating those which will exist when the building is occupied.
<br />3.2.2 Application shall not begin until all roofing work has been completed and building
<br />completely enclosed.
<br />3.2.3 All windows and doors shall be in place and glazed- Plastering and concrete work
<br />shall be completed and allowed to dry before the installation of acoustical tile.
<br />3.2.4 Board shall be carefully fitted around diffusers and other ceiling outlets and fixtures.
<br />cooperate with sprinkler, mechanical and electrical contractors to Coordinate work.
<br />'
<br />3.3. Field Painting
<br />3.3.1 Above the Openwork Grid, where color of panels is other than white, spray paint
<br />grid to match panel color before panels are installed. Use line of edge trim of the
<br />Openwork System to determine limits of painting.
<br />3.3.2 In the area where white panels straddle the line of the Openwork System, paint area
<br />of panel inside the Openwork System to match factory -colored panels.
<br />End of Section 09500
<br />Section 09650
<br />Resilient Tile Flooring
<br />1. General:
<br />1. 1. Submittals: Submit Letter Of Intent to comply with specified requirements.
<br />2. Products:
<br />2.1. Vinyl Composition Tile (VCT): Manufacturer, series, and color as indicated on Drawings.
<br />2.2. Rubber Stair Treads and Accessories (RST): Manufacturer, series and color as indicated on
<br />drawings.
<br />2.3. Vinyl Base,
<br />2.3.1 Provide 4" x 1/8" gauge vinyl coved wall base, light gray, with all outside corners
<br />pre -formed.
<br />2.3.2 Adhesive: manufacturer's wall base adhesive.
<br />2.3.3 Acceptable Manufacturers
<br />Armstrong
<br />Burke Flooring Products
<br />Flexco
<br />Johnsonite
<br />Macklanburg-Duncan
<br />Mannington
<br />Other manufacturer as approved by the Architect.
<br />2.4. Reducer strips: 4" vinyl straight base, color to match primary color of adjacent VCT.
<br />2.5. Epoxy Adhesive� Armstrong S-230 two-part epoxy or equal as recommended by tile
<br />manufacturer and approved by Publix.
<br />2.6. All other applications� Mapei G19 Low VOC Urethane or equal as recommended by tile
<br />manufacturer and approved by Publix.
<br />2.7. Accessories and miscellaneous items: Provide all accessory items required for a complete
<br />installation.
<br />3. Execution:
<br />3.1. Pre-lnstallation�
<br />3.1.1 Inspect substrate to determine satisfactory conditions. A satisfactory substrate
<br />surface is defined as one that is smooth and free from cracks, holes, ridges, coatings
<br />preventing adhesive bond, and other defects impairing performance or appearance.
<br />3.1.2 Do not proceed with resilient flooring work until substrate surfaces are satisfactory,
<br />3.2. Vinyl Composition Tilei Set with epoxy adhesive in restrooms (and where occurs in
<br />remodels, within 4'-O" of all refrigerated cases and coolers). Elsewhere use non -epoxy
<br />adhesive as specified. Alternate tile pattern direction.
<br />1
<br />3.3. Vinyl Base: Vinyl base in sales area is required only on exposed walls, i.e. on walls which
<br />do not have cases in front of them. Extend base one foot behind cases. Wall shelving
<br />requires base behind for full length. Use manufacturer's recommended adhesive.
<br />End of Section 09650
<br />Section 09680
<br />Carpet
<br />1. General
<br />1. 1. Extra Stock:
<br />1. 1. I Provide each type, color, pattern, and size used in the work, for Publix' use in
<br />replacement and maintenance, packaged securely to prevent damage, and clearly
<br />raverdrup
<br />S VERDR UP FACILITIES, INC
<br />FLORIDA CORPORATE LICENSE #AA COO 1291
<br />5750 Major Boulevard, Suite 500, Orlando, FL 32819
<br />(407)903-5001 Fax (407)903-5150
<br />ARCHITECT OF RECORD
<br />NAME., FLOYD WILSON McCOLLUM, JR., AIA
<br />REGISTRATION: FLORIDA REG. #AR0016162
<br />DA TE., 02128101
<br />Revision:
<br />Dote: By: Description:
<br />0
<br />V . L<
<br />,
<br />,
<br />-
<br />-0
<br />I
<br />Z)
<br />C 0-
<br />0 � M
<br />Ob,
<br />V)
<br />MAMO#
<br />a)
<br />%�
<br />a
<br />E
<br />%�
<br />(D
<br />4=
<br />r__
<br />M
<br />0=
<br />I,*
<br />.rL
<br />D
<br />IRT
<br />LO
<br />W
<br />c1q
<br />CD
<br />co
<br />co
<br />M
<br />M
<br />-
<br />l.-Moo
<br />a_ 00
<br />0
<br />W
<br /><
<br />0
<br />-
<br />X
<br />-Lli--J,V-
<br />.V--
<br />C/) r-_J LL ,
<br />LU - _00
<br />UJ
<br />W
<br /><
<br />>
<br />W
<br />0
<br />0�
<br />r .)_000
<br />�=f -, -7, C-0
<br />LL 0:��
<br /><
<br />=)
<br />LU
<br />_J
<br />_I
<br />LL
<br />�
<br />T_
<br />LL -
<br />C/) _J 1ZZr
<br />OLULUM
<br />cy
<br />U)
<br />=3
<br />0
<br />-
<br />U)
<br />D
<br />LU C) ��
<br />C)
<br />3::
<br />M
<br />_J
<br />< W
<br />F_ co -J,-E:
<br /><
<br />0*)
<br />M
<br />ft
<br />LU
<br />_J
<br />_J
<br />_J
<br />X:
<br />yj [,_�b
<br />5
<br /><
<br />W
<br />D0�
<br />bF--cD=
<br />,:I- 0-
<br />0-
<br />LU
<br />ce
<br />Z
<br />0
<br />>_
<br />X:
<br />-:]
<br />01-1 3 X W
<br />0
<br />3:
<br />CD
<br />C-4
<br />M
<br />a=
<br />_J
<br />0<0W
<br />1--
<br />0
<br />m
<br />LU
<br />C) LL 10 �--
<br />U)
<br />�-
<br />P
<br />N
<br />Key Plan:
<br />Scales:
<br />Sverdrup Project No.: 22196390
<br />Drawing Title:
<br />SPECIFICATIONS
<br />Date: 03/12/99
<br />Designed By: RBJ
<br />Drawn BT RM
<br />Checked BY: FWNI
<br />Drawing No.:
<br />PM7
<br />I
<br />I
<br />x_ $I ..
<br />
|