|
INSTALLATION DETAILS FOR FLANGE WINDOWS IN
<br />WINDZONES
<br />screw embedment oft" is maintained in the buckstrip. Window
<br />fasteners should be located a maximum of 4 from each corner
<br />A HEADER
<br />}�IgLL HEADER PLYWOOD
<br />B FLASHING SHEATHING
<br />OF 15OMPH OR LESS (DETAIL A)
<br />and maximum of 18" O.C. It is recommended that fasteners no
<br />1J
<br />1 u�kRl ip z?nlsst l e set in a dead at sealant. The exteriorjoint
<br />be installed through the sill of the window. The actual size of
<br />RESISTANT F . WINDOW
<br />FASTENER
<br />v •
<br />l 1 Cwiveh the buckstrip and masonry must also be sealed.
<br />the buckstrips should be no less than l2" X 2 a". Duckstrips
<br />BARRIER i
<br />•,
<br />» .«
<br />buckstrips shall run the entire length of the rough opening. A
<br />should be installed using minimum ilh X 24 masonry screws,
<br />EXTMOR , WOOD
<br />A INTERIOR
<br />tNTER1OR •
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps
<br />y,
<br />to maintain 14 embedment, and be i8' O.C.
<br />FACADE ; f := _; � _ , FRAME
<br />r HEADER.
<br />PRESSURE TREATED
<br />must be sealed. Buckstrips should be pressure treated yellow
<br />li i> Y
<br />• .
<br />INSTALLATION DETAILS FOR FIN WINDOWS IN
<br />BUCKSTRIP (MIN. 2}'
<br />pine, spruce or comparable lumber. In accordance with the
<br />DRYWALL
<br />- ° AS SHOWN)
<br />Florida Building Code, a taper, or bevel on the buck is
<br />WINDZONES OF 150MPH OR LESS (DETAIL B)
<br />RIGID FLASHING
<br />(OPT., BY OTHERS)
<br />M ii'r'�90
<br />a, �MI- thld if the wiiiJow frame is fully supported by the
<br />VOID WITH
<br />Installation fasteners for windows should be a
<br />-•
<br />• - -LER
<br />lluc%s#rip at both the interior and exterior.
<br />„A.
<br />minimum 1! nail or 14 wood Screws, With an embedmentof
<br />INtiERIOR FILL INTERIOR
<br />_,. MINIMAL EXPANDING FOAM
<br />-
<br />'a6lb
<br />s"
<br />at least I ". Fasteners should be located at a maximum of 4"
<br />-- IF PER CODE
<br />' ftL1_ lkltl; WITH
<br />tii!i> laL
<br />If usin' thick wood buckstrips:
<br />"—
<br />from each corner and 18" O.C. for screws and 9" O.C. for
<br />'' •
<br />ANDiNG FOAM
<br />4 - • - IF PER 'CODE
<br />Installation fasteners should be a minimum 1 ,'x 24' masonuy
<br />nails. It is recommended that all screws or nails be sealed to
<br />4'
<br />EXTERIOR
<br />screws, installed through the window and buckstrip, into the
<br />prevent infiltration of air and water. Product maybe shimmed
<br />IFtISE� SHIMS '
<br />JAMBS
<br />masonry. Window may be shimmed as necessary, provided a
<br />as necessary.
<br />•
<br />minimum screw embedment of 14" is maintained in the
<br />Flexible flashing should be installed in a
<br />_ C2 INSTALLING ® &
<br />r
<br />IIT-Ssomy, hasteners should be located a maximum of 4" from
<br />weatherboard fashion. The top layer should overlay any layer
<br />LEVEL
<br />F °o
<br />each corner and maximum of 18" O.C. It is recommended that
<br />beneath it. The weather resistant barrier should then cover the
<br />• FLEXIBLE
<br />RESISTANT �
<br />IF NECESSARY, `STET
<br />fasteners not be installed through the sill of the window. Tie
<br />flexible flashing at the header. The application of the weather
<br />BARRIER FINISHED
<br />USE SHIMS
<br />actual size of the buckstrips should be no less than 4" X 2gt"-
<br />resistant barrier will vary based on when it is installed. If it is
<br />pR ISLE WE, ER • SILL
<br />•
<br />installed after the window, it should be tucked under the sill
<br />FLASHING •
<br />INSTALLING To • _
<br />KEEP PLUMB & _ =
<br />If using lz " thick or greater wood buckstrips (not shown):
<br />Bashing and overlap the jambs and head flashing.
<br />-
<br />JAMBS - _
<br />Window installation fasteners should be a minimum #8 X i"
<br />woad screws, installed through the window into the buckstrip.
<br />LEVEL•
<br />n
<br />ROM "
<br />R�
<br />FA�r DNAAacanrsMRAL
<br />TERIOR
<br />ExACADE
<br />FACADE
<br />+ WINDOW�
<br />v
<br />• PRE -CAST "TAT, PoURM
<br />Window m .y be shimmed as necessary, provided a minimum
<br />�
<br />Z+ CONCRETE Sid ? 7� W'N1 M SILLThe
<br />-..—
<br />SILL
<br />L
<br />Window clepioted to this raMn-gis intended lor use on typical canstrucucm. It is a response ity of o em to termme tf d is app ica e. A rit as 'ng, vapor
<br />---
<br />barriers, Bin maybe spee[fied by the project arohiieet, Wind and design pressures vary within each state and county. All products manufa0tured by NuAir Inc. meet a
<br />• SEALANT BEAD
<br />• SEALANT BEAD SILL
<br />minimum of 1I0 mph (930 r?P) wind load requirements (per• AAMA 101); please check local building codes for exact requirements. Above details shown for Single Flung
<br />wndow.PorinstsIlalionofAwTing,I[orizontalRoller, orPiei;uei0esignerwindows use the samespecificationsasshownabove for the Single Hung, provided that all
<br />0SEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />unched frarne installation holes ase utilized and with the above mentioned screw s ze and in .
<br />IF NECESSARY.
<br />USE SHWS
<br />WHEN
<br />INSTALLING TO
<br />KEEP PLUMB &
<br />HEADER
<br />• INTERIOR
<br />PRESSURE TREATED
<br />BUCKSTRIIP (MIN. 2J"
<br />AS SHOWN)
<br />SHIM AS NEED@
<br />WINDOW
<br />ASTENER
<br />FILL INTERIOR VOID WITH
<br />MINIMAL EXPANDING FOAM
<br />- IF PER CODE
<br />NO
<br />FASTENERS
<br />THROUGH
<br />SILL
<br />LEVEL. • - -
<br />4
<br />PRE -CASTd
<br />d CONCRETE SILL
<br />• SEALANT BEAD SILL
<br />LrHUN
<br />TALLATION DETAILS FOR NON -IMPACT, FLANGE, SINGLE INSTALLATION
<br />IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall run the entire length of the rough opening. A
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps must
<br />be sealed- Buckstrips should be pressure treated yellow pine,
<br />spruce or comparable lumber. In accordance with the Florida
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />window frame is fully supported by the buckstrip at both the
<br />interior and exterior.
<br />If using 4" thick wood buckstrips:
<br />Installation fasteners should be a minimum J" X 24" masonry
<br />screws, installed through the window and buckstrip, into the
<br />masonry. Window may be shimmed as necessary, provided a
<br />minimum screw embedment of le is maintained in the masonry.
<br />Fasteners should be Iocated a maximum of 4" from each corner
<br />and maximum of 18" Q.C. It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size of the
<br />buckstrips should be no Iess than 4" X 2�'.
<br />If using 1 " thick or greater wood buckstrius (not shown):
<br />Window installation fasteners should be a minimum 410 X 11 "
<br />wood screws, installed through the window into the buckstrip.
<br />Window may be shimmed as necessary, provided a minimum
<br />screw embedment of 11" is maintained in the buckstrip. Window
<br />fasteners should be located a maximum of 4" from each comer and
<br />maximum of 18" O.C. It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size of the
<br />buckstrips should be no less than 1�' X 2J". Buckstrips should be
<br />installed using minimum 1 g' X 24" masonry screws, to maintain
<br />1�' embedment, and be 18" O.C-
<br />The window depicted in this drawing is intended for use on typical construction, It is the
<br />AMRMAN'
<br />IAIR ARCREnul`iu1RAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />A's o�w ; Nt`s' m be specified b the project architect Wind and d pressures vary h d
<br />Menses
<br />may gee y p J design pr ssuro ry within each state an
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FLO(800) 282-6627•www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />tNTERIOR
<br />4� •
<br />= �t
<br />fiXTERtOR
<br />JAMBS
<br />IF NECESSARY,
<br />USE SHIMS
<br />WHEN
<br />INSTALLING TO
<br />HEADER SERIES INSTALLATION DETAILS FOR NON -IMPACT, FLANGE, AWNING
<br />A02/3 ATW WINDOWS 1N WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />-4
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />=1 • between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall run the entire length of the rough opening, A
<br />EXTERIOR INTERIOR buckstrip is not necessary at the sill if it is pre -cast All gaps must
<br />• PRFSSURE TREATED
<br />be sealed. Buckstrips should be pressure treated yellow pine,
<br />Bumsrmp (MIN. 2Ij'
<br />spruce or comparable lumber. In accordance with the Florida
<br />As SHOWN)
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />frame is fully supported by the buckstrip at both the
<br />SHIM AS NEEDED
<br />interior
<br />interior and exterior.
<br />WINDOW
<br />FA5tENER
<br />If usin " thick wood buckstrips:
<br />_ _ _ g
<br />Installation fasteners should be a minimum 16" X 21," masonry
<br />screws, installed through the window and buckstrip, into the
<br />FILL INTERIOR VOID WITH
<br />MINIMAL EXPANDING FOAM
<br />masonry. Window may be shimmed as necessary, provided a
<br />- IF PER CODE
<br />minimum screw embedment of 11' is maintained in the masonry.
<br />Fasteners should be located a maximum of 4" from each comer
<br />No
<br />and maximum of 18" O.C. It is recommended that fasteners not be
<br />FTrtr>
<br />installed through the sill of the window. The actual size of the
<br />S
<br />buckstrips should be no less than 4'X 28".
<br />If using l "thick or greater woad buckstrips (not shown thick or�eater wood buckstrips (not shown):
<br />FINISHED
<br />•
<br />Window installation fasteners should be a minimum #10 X I- "
<br />KEEP PLUMB ar • wood screws, installed through the window into the buckstrip.
<br />l�l - -
<br />• • _ _ Window may be shimmed as necessary, provided a minimum
<br />--. • screw embedment of 14" is maintained in the buckstrip. Window
<br />f v cr q fasteners should be located a maximum of 4" from each corner and
<br />• PM -CAST- • ''EAT. POUR£t)
<br />CONCRETE sat G CONCRETE Salt maximum of 19" O.C. It is recommended that fasteners not be
<br />i SEALANT BEAD installed through the sill of the window- The actual size of the
<br />buckstrips should be no less than 1z" X 21,". Buckstrips should be
<br />installed using minimum �" X 21" masonry screws, to maintain
<br />l4" embedment, and be IS" O.C.
<br />e in this drawing
<br />The window depicted ra 1TIg is intended for use on typical construction. It is the
<br />11A PAUCAN
<br />ARCS i S n1aAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, Bic.
<br />A SOCI oTUN may be specified by the project architect Wind and design pressures vary within each state and
<br />TIR MEMBER county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FLs(800) 282-6627o www.NuAir com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />FLID013 £
<br />FLASHING
<br />WEATHER
<br />ESiSTANT-
<br />BARRiER
<br />RIGID FLASHING
<br />(on., BY OTHERS)
<br />HEADER sH�rG Di
<br />SERIES
<br />INSTALLATION DETAILS FOR NON -IMPACT, FIN, HORIZ, ROL-
<br />OH2/3 HR
<br />LER WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />WINDOW
<br />�. -FASTENER
<br />Window installation:
<br />'
<br />wowInstallation
<br />fasteners for windows should
<br />•
<br />- ' - :: ';
<br />: :':
<br />FRAME
<br />be a minimum 12", 4d nail or 6 x l" drywall screw,
<br />•
<br />^'s
<br />HEADER
<br />with an embedment of at least 12". Fasteners
<br />DRYWALL
<br />should be located at a maximum of 4" from each
<br />comer and 18" O.C. for screws and 9" O.C. for
<br />nails.
<br />FILL INTERIOR VOID WITH
<br />MINIMAL 'EXPANDING FOAM
<br />It is recommended that all screws or
<br />- IF PER CODE
<br />nails be sealed to prevent infiltration of air and
<br />water. Product may be shimmed as necessary,
<br />uSE SHIMS
<br />Weathe[proofing_
<br />_proofing
<br />1
<br />WHEN
<br />KEEP P uM °&
<br />Flexible flashing should be installed in a
<br />ANT
<br />LEVEL
<br />weatherboard fashion. The top layer should overlay
<br />R FLEXIBLE
<br />any layer beneath it. The weather resistant barrier
<br />FLASHING
<br />FINISHED
<br />should then cover the flexible flashing at the
<br />WEATHER •
<br />SILL
<br />header.
<br />Esi
<br />BARRIER
<br />•
<br />The application of the weather resistant
<br />A
<br />all
<br />-
<br />barrier will vary based on when it is installed. If it
<br />IMIOR
<br />FACADE
<br />is installed after the window, it should be tucked
<br />wlNDow
<br />under the sill flashing and overlap the jambs and
<br />FASTENER
<br />head flashing.
<br />SILL
<br />• SEALANT BEAD
<br />OSEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />depicted this drawl is • lded for c
<br />T � The window dap 1 drawing inter use on typical construction. It is fire
<br />AMh1tiCAN
<br />ARCH
<br />ITECrURAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />MANUFACTURES
<br />AssCC(AUON may be specified by the project architect. Wind and design pressures vary within each slate and
<br />MrMBeu county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-66270www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />WEATHER
<br />ESISTANT
<br />BARRIER
<br />RIGID FLASHING
<br />(OPT. BY OTHERS)
<br />HEADER ADER PLYWoOD
<br />SERIES 900
<br />INSTALLATION DETAILS FOR NON -IMPACT, FIN, SINGLE
<br />HONG WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />SHEATHING
<br />& 950 SH
<br />WINDOW
<br />FA''fENER
<br />Window Installation:
<br />- - —
<br />�WDRYWALL
<br />Installation fasteners for windows should
<br />• •_..
<br />-.;: d
<br />�Ebe
<br />a minimum 1a", 4d nail or 6 x 1z" drywall screw,
<br />HEADfTt
<br />with an embedment of at least 12". Fasteners
<br />should be located at a maximum of 4" from each
<br />comer and IS" O.C; for screws and 9" O.C. for
<br />FILL INTERIOR VO4D WITH
<br />nails.
<br />MINiMALE PA G
<br />It is recommended that all screws or
<br />DE
<br />nails be sealed to prevent infiltration of air and
<br />water. Product may be shimmed as necessary -
<br />IF NECESSARY.
<br />USE SHIMS
<br />WHEN
<br />INSTALLING TO
<br />Weatherproofing:
<br />KEEP PLUMB &
<br />LEVEL
<br />Flexible flashing should be installed in a
<br />FLUweatherboard
<br />fashion. The top layer should overlay
<br />FLASHINNG
<br />any layer beneath it. The weather resistant barrier
<br />SILLISFiID
<br />should then cover the flexible flashing at the
<br />MR R • •
<br />rANr
<br />header.
<br />RIi R
<br />_ -
<br />_-
<br />The application of the weather resistant
<br />IOR
<br />r
<br />barrier will vary based on when it is installed. If it
<br />WE
<br />is installed after the window, it should be tucked
<br />WINDOW ER
<br />under the sill flashing and overlap the jambs and
<br />SILL
<br />head flashing,
<br />• SEALANT BEAD
<br />QSFAi.ANT BEAD IF FLASHING IS NOT ADHESIVE
<br />d d 'cted 'n
<br />th' dra i i intended far use on typical construction It is the
<br />The win ow Bpi L [s w ng s
<br />IRMAMMUCANI
<br />barriers, etc.
<br />vapor bawl
<br />flashing, ,
<br />e determine if it is applicable. Additional as
<br />of oth rs to deie,
<br />��,/I� ARCaPrtSCTURAL responsibility1T g 1�
<br />a1ANUFACrf1RFc
<br />fate an
<br />AssoLTano>< may be specified by the project architect. Wind and design pressures vary
<br />within each s
<br />"EMBER county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL 0(800) 282 8627•Wwwt-NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />BARRIER
<br />RIGID FLASHING
<br />(OPT.. BY OTHERS) —
<br />INTERIOR
<br />WFATHET
<br />R�slsral
<br />t • BARRIER
<br />•
<br />1�I'SII'�//�
<br />FLUBLE
<br />FLASHING
<br />YliNDow
<br />FILL INTERIOR VOID WITH
<br />MINIMAL EXPANDING FOAM
<br />IF PER CODE
<br />IF NECESSARY,
<br />USE SHIMS
<br />WHE
<br />INSTALLING TO
<br />KEEP PLUMB do
<br />LEVEL.
<br />JAMBS BARRIO • - -
<br />EXTERIOR
<br />FACADE
<br />WINDOW
<br />FASTENER
<br />SILL
<br />• SEALANT BF-AD
<br />OSEALANT BD IF FLASHING IS NOT ADHESIVE
<br />INSTALLATION DETAILS FOR NON -IMPACT, FIN, AWNING
<br />WINDOWS IN WINDZONES OF ISOMPH OR LESS (per FBC 2001)
<br />Window Installation:
<br />Installation fasteners for windows should
<br />be a minimum 1�', 4d nail or 6 x lJ" drywall screw,
<br />with an embedment of at least 1�'. Fasteners
<br />should be located at a maximum of 4" from each
<br />collier and 18" O.C. for screws and 9" O.C. for
<br />nabs,
<br />It is recommended that all screws or
<br />nails be sealed -to prevent infiltration of air and
<br />water. Product may be shimmed as necessary.
<br />Weatherproofing:
<br />Flexible flashing should be installed in a
<br />weatherboard fashion. The top layer should overlay
<br />any layer beneath it. The weather resistant barrier
<br />should then cover the flexible flashing at the
<br />header.
<br />The application of the weather resistant
<br />barrier will vary based on when it is installed. If it
<br />is installed after the window, it should be tucked
<br />under the sill flashing and overlap the jambs and
<br />head flashing.
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />AME9nCAN
<br />AN
<br />ARMTECn1RAL responsibility of others to determinc if it is applicable- Additional flashing, vapor barriers, etc.
<br />�A� u may be specified by the project architect. Wind and design pressures vary within each state and
<br />MW"M county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-6627owwwAtiAimom load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />FLEXIBLE
<br />FLASHING
<br />WEATHER
<br />RIGID FLASHING
<br />(OPT, BY OTHERS)
<br />PLYWOOD
<br />SERIES 900'
<br />HEADER NG
<br />PW & DPW
<br />WINDOW
<br />f
<br />i ^FASTENER
<br />WOOD
<br />�f
<br />HEADER
<br />•
<br />•
<br />,
<br />,
<br />I
<br />INTERIOR VOID WiTH
<br />4AL. EXPANDING FOAM
<br />- IF PER CODE IF NECESSARY,
<br />USE
<br />WHEN
<br />INSTALLING
<br />KEEP PLUMB
<br />LEVEL
<br />EMBLE
<br />4SHING
<br />* •
<br />•
<br />DRYWALL
<br />SHIMS
<br />TO
<br />&
<br />FlNiSHID
<br />SILL
<br />WINDOW
<br />FASTENER
<br />SILL
<br />• SEALANT BEAR
<br />INSTALLATION DETAILS FOR NON4MPACT, FIN, FIXED
<br />WINDOWS IN WINDZONES OF 150MPH OR LESS (per FBC 2001)
<br />Window Installation:
<br />Installation fasteners for windows should
<br />be a minimum *', 4d nail or 6 x li" drywall screw,
<br />with an embedment of at least *. Fasteners
<br />should be located at a maximum of 4" from each
<br />corner and 18" O.C. for screws and 9" O.C. for
<br />nails.
<br />It is recommended that all screws or
<br />nails be sealed to prevent infiltration of air and
<br />water. Product may be shimmed as necessary.
<br />Weatherproofing:
<br />Flexible flashing should be installed in a
<br />weatherboard fashion. The top layer should overlay
<br />any layer beneath it. The weather resistant barrier
<br />should then cover the flexible flashing at the
<br />header.
<br />The application of the weather resistant
<br />harrier will vary based on when it is installed. If it
<br />is installed after the window, it should be tucked
<br />under the sill flashing and overlap the jambs and
<br />head flashing.
<br />OSEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />AMMLGAN
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />C
<br />or
<br />ARCFlrI8C1'URAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />MANOVAA&VXMC IVIIA#&AR
<br />TURtS
<br />ASSUCGATION may be specified by the project architect. Wind and design pressures vary within each state and
<br />MEMBER county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (1130 DP) wind
<br />Tampa, FL•(800) 282.6627•www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />HEADER SERIES
<br />INSTALLATION DETAILS FOR NON -IMPACT, FLANGE, HORIZ. ROm-
<br />OH2/3 HR
<br />LER WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />.4
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />`° •
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall run the entire length of the rough opening. A
<br />@XTMOR iFTTERIOR
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps must
<br />•
<br />INlt ifOR pRESSURE TREATED
<br />be sealed, Buckstrips should be pressure treated yellow pine,
<br />• BUCKSTRiP (MIN. 2r
<br />spruce or comparable lumber. In accordance with the Florida
<br />srrowN)
<br />n�
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />flame is fully supported by the buckstrip at both the
<br />�• SHIM AS NEEDEDwindow
<br />interior and exterior.
<br />• WINDOW
<br />F4 ER
<br />If using " thick wood buckstrips:
<br />=�
<br />Installation fasteners should be a minimum" X 24" masonry
<br />v - FILL INTERIOR VOID WITH
<br />,: • MINIMAL EXPANDING FOAM
<br />screws, installed through the window and buckstrip, into the
<br />IF PER CODE
<br />masonry. Window may be shimmed as necessary, provided a
<br />JAMBS
<br />minimum screw embedment of l4" is maintained in the masonry.
<br />Fasteners should be located a maximum of 4" from each comer
<br />and maximum of 18" O,C, It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size o£the
<br />NO
<br />FASTENERS
<br />buckstrips should be no less than 4" X 2g".
<br />IFSHIMS ' THROUGH
<br />SILL
<br />If using 4 " thick or meter wood buckstrips (not shown):
<br />Window installation fasteners should be a minimum #10 X 1 J "
<br />IN
<br />•
<br />INSTALLING 70
<br />KEEP PLUMB & •
<br />wood screws, installed through the window into the buckstrip.
<br />_
<br />LEVEL
<br />• • . - - =
<br />Window may be shimmed as necessary, provided a minimum
<br />•
<br />screw embedment of 14" is maintained in the buckstrip. Window
<br />a
<br />cT�
<br />fasteners should be located a maximum of 4" from each corner and
<br />A CAN PRE -CAST SILL d CONCRETE SILL
<br />ETEinstalled
<br />maximum of 18" O.C. It is recommended that fasteners not be
<br />through the sill of the window. The actual size of the
<br />• SEALANT BEAD SILL
<br />buckstrips should be no less than 1�' X 2p". Buckstrips should be
<br />installed using minimum l6" X 24" masonry screws, t0 maintain
<br />14" embedment, and be 18" O.C.
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />AMFttiCAN
<br />ARCHITECTURAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />MANMMRR8
<br />AssopATroN may be specified by the project architect. Wind and design pressures vary within each state and
<br />tT
<br />AWRMMywm county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />L*(800) 282.6627owww,NuAir-corn load requirements (per AAMA 101); please cheek local building axles for exact requirements.
<br />HEADER SERIES 90€I
<br />IPW
<br />INSTALLATION IIETAILS FOR NON -IMPACT, FLANGE, FIXED
<br />I)I'
<br />WINDOWS IN WINDZONES OF ISOMPH OR LESS (per FBC 2001)
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />•
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall run the entire length of the rough opening. A
<br />EXTERIOR INTERIOR
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps must
<br />•
<br />INTERIOR PRESSURE TREATED
<br />be sealed. Buckstrips should be pressure treated yellow pine,
<br />• BUMM41P (MIN. 21"
<br />spruce or comparable lumbar. In accordance with the Florida
<br />. a As SHOWN)
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />Q
<br />v•
<br />window frame is fully supported by the buckstrip at both the
<br />SHIM AS 1
<br />interior and exterior.
<br />WINDOW
<br />ER
<br />If using+" thick wood buckstrips:
<br />:Q FILL INTERIOR VOID WITH
<br />lik"
<br />Installation fasteners should be a minimum 16 X 2s4 masonry
<br />MINIMAL EXPANDING FOAM
<br />a • - IF PER CODE
<br />screws, installed through the window and buckstrip, into the
<br />�;
<br />TtIOR
<br />masonry. Window may be shimmed as necessary, provided a
<br />JAMBS
<br />minimum screw embedment of 1�' is maintained in the masonry,
<br />Fasteners should be located a maximum of 4" from each corner
<br />and maximum of 18" O.C. The actual size of the buckstrips should
<br />NO
<br />FASTF'NIJRS
<br />be no less than +" X Zs'.
<br />THROUGH
<br />SILL
<br />If using 11i " thick or greater wood buckstrips (not ShoIF wn
<br />NECESSARY.1
<br />USE
<br />Window installation fasteners should be a minimum #10 X &
<br />WHEN
<br />WEE" •
<br />wood screws, installed through the window into the buckstrip.
<br />INSTALLING TO
<br />KEEP PLUMB & • • - - - _
<br />-
<br />Window may be shimmed as necessary, provided a minimum
<br />tEvEi.. _ _- •
<br />• V �l
<br />screw embedment of A' is maintained in the buckstrip. Window
<br />e
<br />a
<br />fasteners should be located a maximum of 4" from each corner and
<br />PRE -CAST
<br />' Z CONCRETE SILL $CONCRETE SILL
<br />maximum of 18" O.C. The actual size of the buckstrips should be
<br />p
<br />no less than 1�' X3 281". Buckstrips should be installed using
<br />BEAD SILL
<br />minimum ,6' X 24" masonry screws, to maintain
<br />• SEALANT
<br />la' embedment, and be 18" O.C.
<br />CAN The window depicted in this drawing is intended for use on typical construction. It is the
<br />AARRCCH,`M-MRAL responsibility of others to determine if it is applicable, Additional flash'
<br />MANUt'AC'NRES p �' pP mg, vapor barriers, etc.
<br />11MAIR
<br />ASS(.GA•,�UN may be specified by the project architect Wind and design pressures v within each state and
<br />MEMBER P gn p sty
<br />J�
<br />county. All products manufactured by NuAir Inc. meet a minimum of 1 ] 0 mph (R30 DP) wind
<br />Tampa, FLs(800) 282-6627•www.NuAir-coin load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />SERIES 201)
<br />INSTALLATION DETAILS FOR NON -IMPACT, SLIDING GLASS
<br />HEADER & 500 SGD
<br />DOORS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall run the entire length of the rough opening,
<br />EXTERKSR • INTERIOR
<br />except door sill. All gaps must be sealed, Buckstrips should be
<br />INFERIOR PRESSURE
<br />pressure treated yellow pine, spruce or comparable lumber. In
<br />BUCTED
<br />KSTTRIP
<br />accordance with the Florida Building Code, a taper, or bevel
<br />•
<br />on the buck is acceptable if the door frame is fully supported
<br />n= AIM
<br />by the buckstrip at both the interior and exterior,
<br />NEEO>rD
<br />DOOR
<br />,, ,
<br />If using " thick wood buckstrips:
<br />�'
<br />Installation fasteners should be a minimum 16" X 24" masonry
<br />screws, installed through the door frame and buekstrip, into the
<br />'
<br />masonry. Door may be shimmed as necessary, provided a
<br />minimum screw embedment of A' is maintained in the
<br />y MINIMUM
<br />masonry, Fasteners should be located a maximum of 4" from
<br />'
<br />each corner and maximum DNS" O.C. The width of the
<br />REM-
<br />MENDED
<br />buckstrips should be no less than the frame frame of the door.
<br />0 • AFTER
<br />INSTALLATION,
<br />SEALBETWEE
<br />JAMBS HORIZON•rAL JOINT
<br />Ifusing 11 " thick or ater wood buckstjps not shown):" thick or ater wood buckstjps not shown):
<br />��
<br />T PA
<br />installation fasteners should be a minimum #10 X W
<br />AND JAMBDoor
<br />F1
<br />wood screws, installed through the window into the buckstrip.
<br />I�crERwR
<br />Door may be shimmed as necessary, provided a minimum
<br />•
<br />screw embedment of Ik" is maintained in the buckstrip. Door
<br />FILL INTERIOR VOID WrM A
<br />MINIMAL EXPANDING FOAM Q : NECESSARY,
<br />WRj•Yit'.N
<br />fasteners should be located a maximum of 4" from each comer
<br />a USE
<br />- IF PER CODE INSTALLING TO
<br />and maximum of 18" O.C. The width of the buckstrips should
<br />xCEP PLUMB de LEVEL
<br />be no less than the frame frame of the door. Buckstrips should
<br />• SFALA�Cr $� 1 RACK
<br />be installed using minimum J" X 24 ` masonry screws, to
<br />maintain li" embedment, and be 18" O-C.
<br />The door depicted in this drawing is intended for use on typical construction. It is the
<br />Aar criTectvRAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />T AMF:RTEC
<br />MANnFAC7URr:S
<br />ASSOMUON Ina be specified
<br />+, fled b the project architect. Wind and design v within
<br />r �MentBEa Y P Y P J gn sty each state and
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL •(BOO) 282-6627•www.NaAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />SERIES 200
<br />INSTALLATION DETAILS FOR NON -IMPACT, SLIDING GLASS
<br />& 500 SGD
<br />DOORS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />HEADER
<br />Sliding Glass Door Installation;
<br />Installation fasteners for jambs and
<br />INTERIOR • • INTERIOR
<br />header should be a minimum #10 x ley" screw.
<br />Installation fasteners for the track should be a
<br />Q • DOOR AIM
<br />FASTENER
<br />minimutn lj' masonry screw. All fasteners should
<br />have an embedment of at least 11". Fasteners
<br />should be located at a maximum of 4" from each
<br />corner and 1.8" O.C. for screws.
<br />It is recommended that all screws be
<br />sealed to prevent infiltration of air and water,
<br />Product may be shimmed up to 4' if necessary.
<br />MINIMUM
<br />JAMBS MENi�
<br />Weatherproofing:
<br />• INSTAILLATTo, SEAL,
<br />Flexible flashing should be installed in a
<br />HORIZONTAL JOINT
<br />EXTERIOR BETWEEN TRACK
<br />weatherboard fashion. The top layer should overlay
<br />AND ,�B
<br />L
<br />any layer beneath it. The weather resistant barrier
<br />should then cover the flexible flashing at the
<br />header.
<br />FILL INTERIOR VOID WITH
<br />INTERIORVOID
<br />The application of the weather resistant
<br />MINIMAL FOAM a IF EcessARY,
<br />- d USES, SHIMS WHEN
<br />barrier will vary based on when it is installed. If it
<br />- IF PER CODE
<br />is installed after the door, it should be tucked under
<br />KEEP PLUMB &
<br />the sill flashing and overlap the jambs and head
<br />• SEALANT' BEAD TRACK
<br />flashing.
<br />The door depicted in this drawing is intended for use on typical construction, It is the
<br />AMEYt1CAN
<br />AACTITTEC7URA 71MRL responsibility of others to determine if it is applicable. Additional flashing, vapor homers, etc.
<br />MANUFACTURE'S
<br />ASSUCLATTON may be specified b t
<br />y pee y he project architect. Wind and design pressures vary within each state and
<br />� Reg
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-S627•www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />0
<br />6"
<br />6#
<br />l�l
<br />THERMA-TRU INSTALLATION
<br />KEY DIFFERENCES CHECK LIST
<br />Rou h openings are 1/4" smaller on each side and 1/4" smatter on the
<br />hewer than standard Therma-Tru rough opening dimensions,
<br />Use only a maximum of 1/4" thick shims,
<br />Predrill the jambs and headers using 1/8" drill bit. Predrilling
<br />increases structural performance.
<br />Use only 2--1/2' wood screws (#8 and #10) when securing the pre
<br />hung frame to the rough opening buck, Drywall scf-ews, deck screws,
<br />and nails are insufficient anchors, and should , not bey substituted for
<br />wood screws,
<br />Be certain of the number and placement of all screws securing the frame
<br />to the rou h opening buck. Consult the architect or engineer of record
<br />concerning Yastening the buck to the rest of the building structure,
<br />CONTRACTOR TO PROVIDE A I x P,T, BUCK STRIP CUNT, AT
<br />OPENING SIDES AND HEADER,
<br />1 x BUCK STRIPS WILL BE ACCEPTABLE PROVIDED THE
<br />8/16" DIA FLATHEAD TAPCONS ARE PROVIDED SPACED AS
<br />SHOWN, THE TAPCONS ARE TO BE CONTINUOUS THRU THE
<br />OFO1 1/4" NBEDMENT DINTO THEIMASONRYAJAMBS,MINIMUM
<br />6" 6
<br />SPA(
<br />EVEI
<br />6" 6"
<br />SINGLE DOOR
<br />u
<br />SINGLE DOOR W SIDELITE SINGLE DOOR W/ SIDELITES
<br />"6"
<br />u
<br />r
<br />lit
<br />I
<br />EI i
<br />it I
<br />1 II
<br />fl
<br />IIi
<br />111
<br />"
<br />�-
<br />6
<br />"
<br />DOUBLE DOOR W/ SIDELITES
<br />" 6
<br />'PACE
<br />:VENT_.
<br />vi E
<br />I 1
<br />I
<br />"
<br />u
<br />ZL CREATED 01-02-02
<br />120 MPH
<br />3 SEC. GUST
<br />DOUBLE DOOR
<br />"
<br />iPACE
<br />_VENLY
<br />
|