Laserfiche WebLink
L� .,i ,.I Ik i� � I .t..,,„i..... ,. `- - a. -� d.. � i. <br />c <br />a <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />T.O.M. <br />12 <br />5� <br />--------- <br />,_ohh <br />15'-0" RIDGE VENT <br />12 <br />OFFRIDGE VENT <br />EXTENDED <br />OVERHANG TO <br />BE CENTERED <br />ON DOOR <br />12 <br />::Z�_5 <br />6-0' T-1 <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />REAR ELEVATION - Al <br />14'-0" RIDGE VENT <br />SCALE: 1 /4"= V-0" <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />(TYP. ) <br />12 <br />�5 <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />"G.C. VERIFY ROOF PITCH" <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />"ELECTRICAL SPECIFICATION NOTES" <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />T.O.M. <br />HDR HGT. <br />--------------------------------------------------------------------------------------------------------------- - -- ------ <br />10 <br />TEXTURED TEXTURED 01 <br />CEMENTICIOUS CEMENTICIOUS <br />FINISH ON C.M.U. FINISH ON C.M.U. 3'-0" <br />(TYP.) (TYP.) <br />Zm <br />F.FL. <br />RIGHT ELEVATION - Al <br />E: 1 /4"=V-0" <br />ISO" <br />O <br />0 <br />1/fry <br />O�'I <br />S' <br />r. <br />_ J <br />QIk <br />s • <br />•'' <br />CO <br />\ <br />�. F L <br />WflROFESS�O\� <br />� rffiflll11N1� <br />To the best of the Engineers knowledge, iMonnation and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineers signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />M <br />h <br />$ <br />o E <br />a <br />LL <br />Lo <br />ym J <br />Qai <br />r, rZ P - W at <br />LL v M Y <br />"" a <br />is <br />0 <br />0 <br />W <br />�C m O <br />C) a <br />IL L <br />a <br />N MZ CN O <br />U U � <br />Z <br />O y <br />❑❑❑ <br />W <br />z N <br />z � <br />z <br />d N <br />N <br />- N <br />C7 <br />Z!�fu <br />V <br />U <br />w <br />� <br />0 <br />l/'I <br />LU s <br />cNd. <br />® <br />U � <br />LLh J <br />U <br />fat <br />¢ � w <br />. <br />O <br />M <br />p <br />W <br />z <br />J <br />03 <br />i <br />,n <br />�O <br />ZO <br />o <br />Ico <br />E <br />N <br />wi <br />z� <br />ip <br />oa <br />�0 <br />H <br />� g <br />9 <br />C <br />O <br />� <br />�o <br />OZ <br />Z <br />d 3 <br />GW <br />$ <br />irk <br />ZZ <br />ao <br />W <br />wLL <br />�W <br />w <br />Mill <br />O <br />O <br />2 <br />Lo <br />C9 <br />L <br />� <br />r <br />t0 J <br />11• <br />�1 <br />.� <br />n/ <br />LC <br />d <br />N <br />C:) <br />O <br />v <br />(.0 <br />%%"i <br />W <br />r <br />r <br />o Nr <br />00 N <br />r <br />r <br />E <br />c CV <br />CM <br />N <br />Z <br />Z <br />42) <br />w <br />a <br />U <br />¢ p <br />JOB <br />NO: <br />21-1075 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.2 <br />