3197 Moulden Hollow Dr - Laserfiche WebLink

Browse Search

VENTED SOFFIT 46 SQ. FT. Egg, VENTED SOFFIT 28 SQ. FT. VENTED SOFFIT 28 SQ. FT. VENTED SOFFIT 31 SQ. FT. ATTIC VENTILATION CALCULATIONS - Al ATTIC VENTILATION REQUIRED UPPER VENTILATION PROVIDED 1/150 Rule (No Upper Ventilators 1/300 Rule Ridge Vent Amt Off -Ridge Req.) (Must Provide Upper Ventilators) (Ft.) Amt. Total Ventilation ATTIC Provided SPACE SQ. FT. Total SQ. SQ. FT, SQ. IN. of by Upper SQ. IN. of of vented IN. of of ventilation to SQIN. of SQ. IN. of Ventilators ventilation required ventilation vented be provided by . Ventilation Ventilation (See Elev ) eSoffiterie needed required soffit upper needed ventilators Main 4.000000 2.000000 Floor 1080 1037 148 518 37 259 336.0 60.0 276.0 (Zone 1) Main 0.0 0.000000 Floor 16 15 2 8 1 4 0.0 0.0 (Zone 2) 0.0 Upper 16.000000 0.000000 Floor 1166 1119 160 560 40 280 240.0 (Zone 3) 240.0 0.0 "NOTE — GENERAL CONTRACTOR MUST ENSURE THAT PROPER VENTILATION IS PROVIDED AT EAVES/SOFFITS AS REQUIRED BY FBC 5th ED. RESIDENTIAL. VENTED SOFFIT LEGEND 771 IF SOFFIT IS LABELED AS "NON -VENTING" FIRE PROTECTION WILL BE INSTALLED AS REQUIRED BY SECTION R302 OF THE FBC 5th EDITION (2014) RESIDENTIAL. IF LABELED AS "VENTED", NO FIRE PROTECTION WILL BE REQUIRED. ------- ;.7M VENTED SOFFIT VENTED SOFFIT 28 SQ. FT. ZONE-2 ATTIC SPACE 16 SQ. FT. VENTED SOFFIT 14 SQ. FT. ROOF PLAN SCALE: Y4'=V-0" General Notes ROOF CRITERIA: • 12" OVERHANG U.N.O. • PLUMB CUT FASCIA ROOF • PITCH PER ELEVATION **G.C. VERIFY ROOF PITCH** ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE CONTRACTORS RESPONSIBILITY TO VERIFY ROOF SLOPE REQUIREMENTS WITH TRUSS MANUFACTURER. **ELECTRICAL SPECIFICATION NOTES** ELECTRICAL CONTRACTOR MUST VERIFY WITH THE SPECIFICATIONS FOR THE TYPE OF FIXTURE TO BE USED. LIGHT FIXTURES SHOWN ARE FOR LOCATION PURPOSES. Exterior Covering R703.6 Exterior plaster. Installation of these materials shall be in compliance with ASTM C 926 and ASTM C 1063. R703.6.1 Lath. All Lath and lath attachments shall be of corrosion -resistant materials. Attached per ASTM C 1063. R703.6.2 Plaster. Plastering w/ portland cement plaster shall be not less than three coats when applied over metal lath or wire lath and shall be not less than two coats when applied over masonry, concrete. R703.6.3 Water-Resisitive Barriers. Water-resisitive barriers shall be installed where cement plaster (stucco) is to be applied over wood -based sheathing, shall include a water -resistive vapor -permeable barrier. The individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing intended to drain to the water -resistive barrier is directed between the layers. The barriers shall consist of one of the following. 1. Two layers of an approved water resistant barrier material in accordance with R703.2. 2. One layer of an approved water -resistive barrier (paperbacked stucco lath) over an approved synthetic house wrap. R703.8 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into the wall cavity or penetration of water to the building structural framing components. Flashing shall be installed at the following locations. • Exterior window/door openings. • Intersection of chimneys or other masonry contructions with frame walls. • Under and at the ends of masonry, wood or metal copings and sills. • Continuously above all projecting wood trim. • Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction. • At wall and roof intersections • At Built-in gutters. Attic Ventilation Attic Ventilation to be in compliance with the Florida Building Code 5th Edition (2014) Residential R806. The Minimum net free ventilating area shall be 1/150 of the area of the vented space. The ventilating area may be reduced to 1/300 provided that at least 40% but no more than 50% of the required ventilation is provided in the upper portion of the space to be ventilated.Upper ventilators shall be located no more than 3 feet (measured vertically) below the ridge or highest point of the space, with the balance of the required ventilation provided by eave or cornice vents. -CALCULATIONS BASED ON THE FOLLOWING VALUES, SEE ROOF PLAN - (Values to be verified with Manufacturer Specifications) • RIDGE VENTS 15 SQ. IN. OF NET FREE AREA / LINEAR FT. • OFF -RIDGE VENTS 138 SO. IN. OF NET FREE AREA / UNIT • SOFFIT VENTS 7 SO. IN. OF NET FREE AREA / SQ. FT. • O'HAGIN WEATHERMASTER (Shingle Roof) - 72 SQ. IN. OF NET FREE AREA/ FT. " (Sq. Ft. Soffit Needed) x 7 = (Sq. In. Needed) / 72 = Amount of O'Hagin Vents Needed • LOMANCO DECK -AIR (Shingle Roof) - 9 SQ. IN. OF NET FREE AREA / FT. "Formula: (Sq. Ft. Soffit Needed) x 7 = (Sq. In. Needed) / 9 = Linear R. of Deck -Air Needed) • O'HAGIN (Tile Roof) - 86.25 SO. IN. OF NET FREE AREA / VENT "Formula: (Sq. Ft. Soffit Needed) x 7 = (Sq. In. Needed) 186.25 = Amount of CPHagin Vents Needed 8 U!P Z co —0 Z Co Q J Z cn i--J w � o U — w O C ~ o o U 0 04 W E -8 Cl) M c N Cl) f`O.ON Ooo _ °' W U U_00 0YP �Y Q 0 u7 O� Q 0 A I ".C. i N UA c_N1• W .0 r3No . • W� LL O 1'9ES$\ Q Z IL1 i�ta Com W V)) o To the best of the Engineer's knowledge, information, and belief, the structural plans and specifications contained within these drawings comply with the Florida Building Code Sth Edition (2014) Residential. Engineer's signature and seal is only for the structural engineering portions of the drawing pages bearing Engineer's signature and seal. O O Z N 0 (D N i>-+HMO M Q Uo) M Ln a cn •� �- z 0 f... LL CL .•. C(-� j a -4 a E00 z� M WJ C:) d' Z W� �a Lu<X �180 z� $xw rn v' 0�QEi3 00 F-U® L 2Z N_ �3 L 0 LU 0„- ,- LL PRE QOwQ Z a E � W J Lei —4 1 LJ.I .. W IN .0 Z u ~ i° Q z y� � F In Z L 591 rz < 0 =1 0 m O ^ g = aW rn T-4 a (n SCALE : AS NOTED DATE : 2/24/2014 TECH: MJAMES VERSIONNO' 10 SHEET NO. 5.0