7866 Gall Blvd (7) - Laserfiche WebLink

Browse Search

Mandatory Requirements (as applicable) Requirements compiled by US Department of Energy and Pacific Northwest National Laboratory. Adopted for FBC with permission. Not all may be applicable Topic Section Component Description Yes N/A Exempt 1. To be checked by Designer or Engineer Insulation 5.8.1.2 Envelope Below -grade wall insulation installed per manufacturer's instructions. Insulation 5.8.1.2 Envelope Slab edge insulation installed per manufacturer's instructions. Insulation 5.5.3.5 Envelope Slab edge insulation depthAength. 11IJ ❑ Insulation 6.4.4.1.5 Envelope Bottom surface of floor structures incorporating 0IJ radiant heating insulated to >=R-3.5. SYSTEM —SPECIFIC 6.5.1, 6.5.1.1, Mechanical Air economizers provided where required (and not ❑ 19 6.5.1.3, 6.5.1.4 exempted), meet the requirements for design capacity, control signal, ventilation controls, high -limit shut-off, integrated economizer control, and provide a means to relieve excess outside air during operation. SYSTEM —SPECIFIC 6.5.1, 6.5.1.2, Mechanical Water economizers provided where required, �-�{ IR 6.5.1.2.1, 6.5.1.3 meet the requirements for design capacity, maximum pressure drop and integrated economizer control. Capable if providing 100% of the expected system cooling load when outdoor SYSTEM —SPECIFIC 6.5.1.5 Mechanical air — 50F. Economizer operation will not increase heating ❑ energy use during normal operation. SYSTEM —SPECIFIC 6.5.2.2.1 Mechanical Three -pipe hydronic systems using a common 13 return for hot and chilled water are not used. SYSTEM —SPECIFIC 6.5.2.2.3 Mechanical Hydronic heat pump systems connected to a common water loop meet heat rejection and heat addition requirements. SYSTEM —SPECIFIC 6.5.1.6 Mechanical Water economizer specified on hydronic cooling and humidification systems designed to maintain inside humidity at >35 OF dewpoint if an economizer is required. SYSTEM —SPECIFIC 6.5.3.1.1 Mechanical HVAC fan systems at design conditions do not 10 exceed allowable fan system motor nameplate hp or fan system bhp. SYSTEM —SPECIFIC 6.5.3.1.2 Mechanical HVAC fan motors not larger than the first available 10 motor size greater than the bhp. HVAC 6.5.6.1 Mechanical Exhaust air energy recovery on systems meeting 1110 ❑ Tables 6.5.6.1-1, and 6.5.6.1-2. SYSTEM —SPECIFIC 7.4.2 Mechanical Service water heating equipment meets efficiency 10 requirements. SYSTEM —SPECIFIC 7.5.2 Mechanical Service water heating equipment used for space Gd heating complies with the service water heating equipment requirements. Insulation 5.8.1.2 Envelope Above -grade wall insulation installed per R1 manufacturer's instructions. Insulation 5.8.1.2 Envelope Floor insulation installed per manufacturer's 13 10 instructions. Controls 10.4.3 Mechanical Elevators are designed with the proper lighting, 10 ventilation power, and standby mode. SYSTEM —SPECIFIC 6.4.1.1, 6.8.1-7a Mechanical Heat Rejection Equipment: Minimum Efficiency Requirement >=40.2 gpm/hp . SYSTEM —SPECIFIC 6.4.1.1, 6.8.1-7b Mechanical Heat Rejection Equipment: Minimum Efficiency 61 13 Requirement >=20.0 gpm/hp. SYSTEM —SPECIFIC 6.4.1.1, 6.8.1-7c Mechanical Heat Rejection Equipment: Minimum Efficiency 10 Requirement > 16.1 gpm/hp. EnergyGauge Summit® Fla/Com-2020. Effective Date: Dec 31, 2020 Florida Building Code, Seventh Edition (2020) - Energy Conservation C402.1.1: ASHRAE Energy Cost Budget Option 5/19/2022 Page 8 of 24