Laserfiche WebLink
<br />CONDUIT OFFSET ASSEMBLY <br /> <br />The Conduit Offset Assembly is used to change direction of the <br />wire rope on detection, mechanical gas valve, and remote pull sta- <br />tion lines. The conduit offset assembly can only be used in the <br />area where the conduit attaches to the regulated release assem- <br />bly. When using the conduit offset assembly, the maximum num- <br />ber of pulley elbows is still allowed. The Conduit Offset Shipping <br />Assembly, Part No. 79825, consists of 6 conduit offsets. <br /> <br />. <br /> <br /> <br />FIGURE 15 <br />000153 <br /> <br />CONDUIT <br />OFFSET <br /> <br />"QUIK.SEAL" ADAPTOR <br /> <br />The "Quik-Seal" adaptor is a listed mechanical bulkhead fitting that <br />produces a liquid-tight seal around both distribution piping and <br />detection conduit which runs through restaurant hoods and ducts. <br />The "Quik-Seal" adaptor accepts threaded pipe or conduit. The <br />adaptor is available for 1/4 in. (Part No. 78195), 3/8 in. (Part No. <br />77284), 1/2 in. (Part No. 77286), or 3/4 in. (Part No. 77288) pipe <br />or conduit sizes. When using with EMT conduit. a conduit con- <br />nector must be installed in each end of the adaptor. The "Quick- <br />Seal" Adaptor Shipping Assembly must be ordered as stated <br />below. <br /> <br />~ <br />1/4 in. <br />3/8 in. <br />1/2 in. <br />3/4 in. <br /> <br />Shipping <br />Assembly <br />~ <br />78196 <br />77285 <br />77287 <br />77289 <br /> <br />Qn.:. <br />24 <br />24 <br />24 <br />24 <br /> <br />Hole Size <br />Required <br />3/4 in. <br />1 1/8 in. <br />1 1/8 in. <br />1 3/8 in, <br /> <br />~ <br /> <br />-tC~:' <br /> <br />. <br /> <br />FIGURE 16 <br />000 154 <br /> <br />SECTION III - SYSTEM COMPONENTS <br />UL EX. 5174 8-1-99 Page 3-5 <br />REV. 1 <br /> <br />"COMPRESSION.SEAL" ADAPTOR <br /> <br />This adaptor is a mechanical bulkhead fitting that produces a <br />liquid-tight seal around pipe and conduit when installing distribu- <br />tion piping and detection conduit through restaurant hoods and <br />ducts. The "Compression-Seal" adaptor is a straight-through <br />design requiring no cutting or threading of conduit or pipe. The <br />adaptor is available for pipe sizes of 1/4 in. (Part No. 79148), 3/8 <br />in. (Part No. 79150), 1/2 in. (Part No. 79146), and EMT conduit <br />size of 1/2 in. (Part No. 79152). Each "Compression-Seal" adaptor <br />shipping assembly must be ordered as stated below. <br /> <br />Shipping <br />Assembly <br />Part No. <br />79149 <br />79151 <br />79147 <br />79153 <br /> <br />Size <br />1/4 in. Pipe <br />3/8 in. Pipe <br />1/2 in. Pipe <br />1/2 in. EMT Conduit <br /> <br />~ <br />24 <br />24 <br />24 <br />24 <br /> <br /> <br />GASKET <br /> <br />. <br /> <br />Hole Size <br />Reauired <br />3/4 in. <br />1 1/8 in. <br />1 1/8 in. <br />1 1/8 in, <br /> <br />COMPRESSION NUT <br /> <br />ADAPTOR BODY <br /> <br />LOCKWASHER <br /> <br />FIGURE 17 <br />000155 <br /> <br />"HOOD SEAL" ADAPTOR ASSEMBLY <br /> <br />This adaptor assembly is a mechanical bulkhead fitting that pro- <br />duces a liquid-tight seal around 1/2 in, EMT conduit when <br />installing the detection line through restaurant hoods and duct. <br />The adaptor accepts a high temperature pulley elbow and. when <br />used, correctly positions the elbow or conduit in line with the con- <br />duit adaptor hole in the detector bracket. The "Hood Seal" elimi- <br />nates the need for multiple elbows when penetrating the top of a <br />hood when installing the detection line. "Hood Seal" Adaptors are <br />available in quantities of 6 as Shipping Assembly Part No. 423253. <br /> <br /> <br />SEAL <br />ADAPTOR <br />BODY_ <br /> <br />. <br /> <br />FIGURE 18 <br />000156 <br />