03-2129 - Laserfiche WebLink

Browse Search

Specifications Control Panels FS1004 FS502 FS302 Initiating Device Circuits - IDCs Class B 10 I 8 6 I 4 2 I 0 5 3 I 1 (Available combinations shown at right) Class A o 1 2 3 4 5 0 1 2 Three Class BlOCs Notification Appliance Circuits - NACs Class B 4 2 0 2 0 (Available combinations shown at right) Class A 0 1 2 0 1 Two Class B NACs Power Supply 3.0 A expandable to 6.0 A 3.0 amps total 2.0 amps total NAC Voltaae Ratina 24 Vfwr 1.5 amps each,2.5 amps total 1.5 amps each 1.5 amps each Maximum NAC current for NAC 1 + 2 or 3 + 4 5.0 A wi optional transformer 2.5 amps total 1.5 amps total AC Input 120 Vac 60 Hz... 1.6 A wi optional transformer 0.8 amps 0.8 amps 230 Vac 50/60Hz... 0.8 A wI optional transformer 0.4 amps 0.4 amps Base Panel Current Draw Standby... 145 mA 120 mA 110 mA Alarm... 250 mA 170 mA 145 mA Panel Battery Charge Capacity (sealed lead acid Up to two 18 Ah batteries Up to 18 Ah, 7Ah max in cabinet * only) Auxiliary Current 0.5 amps max. May be programmed as resetable. Auxiliary Output 19 to 25.7 Vdc IDC Alarm Current 1.5 mA (Consult detector compatibility list pIn 3100468 for maximum detectors per circuit) IDC Circuit Maximum loop resistance: 13 Ohms; Maximum loop capacitance: 0.03 JlF IDC Operating Voltage 16.3 to 25.7 Vdc UL Detector 10 100 Alarm Contact (normally open) Trouble Contact (Form C) 30 Vdc @ 1 A (resistive load) Supervisory Contact (normally open) Operating Environment Temperature: 32 - 1200 F (0 - 490 C); Humidity: 5 - 93% RH, non-condensing Terminals (wire gauge) 18 - 12 AWG 10.75 mm2 - 2.5 mm2) Asynchronous Serial Communications Maximum resistance: 13 Ohms; Maximum capacitance: 0.03 JiF * If larger batteries are required, use the BC-2 battery cabinet. See installation sheet 3100027 for details. DACT - FSDACT (mounts in panel) Receivers Supports two receivers with two phone numbers each Communications Protocol Contact to (SIA DC-05), 4/2 (SIA DC-02 P3l Programming Front panel controls or PC with appropriate software Telephone line connection Two RJ31X (plug-to-plug) cords supplied with DACT Telephone lines Two or one loop start lines on the public switched telephone network. Pulse or DTMF. Telephone wall connector RJ31X/CA31X equiv. or RJ38X/CA38X equiv. Communications Compliance Communications Canada CS-03; FCC/CFR 47 Parts 15 & 68; NFPA 72; UL 864; ULC S527cM87 Operating Environment Temperature: 32-1200 F {0_490 CJ; Humidity: 93% RH, non-condensing Current requirements Standby: 40 mA; Alarm: 60 mA Remote Annunciators FSRSI Remote System Indicator FSRZI-A Remote Zone Indicator Maximum per System All panels: 2 10 zone panel: 4 3 or 5 zone panel: 2 Current Requirements Standby: 12 mA Alarm: 48 mA Standby: 8 mA Alarm 35 mA Voltage Range Minimum: 21 Vdc; Maximum: 25 Vdc Maximum Circuit Capacitance 0.03f.1F Maximum Circuit Resistance 13 Ohms Wire Size 18 - 12 AWG (0.75 mm2 - 2.5 mm2J Mounting ANSI/NEMA OS1-1996 1-3 gang electrical box Operating Environment Temperature: 32 - 1200 F (0 - 490 C); Humidity: 93% RH, non-condensing Remote Relay Module - FSRRM Configured for Zone Mode Configured for Common Mode Maximum per system 10 zone panel: 4; 3 or 5 zone panel: 2 All panels: 2 Current Requirements Standby: 8 mA; Alarm: 65 mA Standby: 30 mA; Alarm: 41 mA Voltage Range Minimum: 18 Vdc; Maximum: 27 Vdc Maximum Circuit Capacitance 0.03 JlF Maximum Circuit Resistance 13 Ohms Wire Size 18 - 12 AWG (0.75 mm2 - 2.5 mm2) Mounting Single FSRRM mounts in plastic track (included) or up to four FSRRMs in an FSRRM-S11 11" track or..dered separately. FSRRMs should be installed in an MFC-A or other listed fire alarm enclosure. Operating Environment , Temperature: 32 - 1200 F (0 - 490 C); Humidity: 93% RH, non-condensing Dimensions 2-3/4" W x 3-318" H x 1-112" D (65.9 mm W x 85.7 mm H x 38.1 mm D) I.sue 2 EDWARDS SYSTEMS TECHNOLOGY Literature Sheet #85005-0118 Not to be used for installation purposes. Fot" the most current' literature end update. visit www~e.t.n.t'. P"ge 5 of 6