Laserfiche WebLink
<br />after the housing is mounted to the duct. The unit shall provide <br />a spacial separation of no less than 1/4" andlor a physical bar- <br />rier between the high- and low-voltage terminals. The enclo- <br />sure shall meet all applicable NEC and NFPA standard regard- <br />ing electrical junction boxes. Terminal connections shall be of <br />the strip-and-c1amp method suitable for 12 to 18 AWG (3.25 to <br />0.75 mm2) wiring. <br /> <br />PRODUCT LINE INFORMATION <br />DH100ACDCI Four-wire ionization duct smoke detector. <br />DH100ACDCP Four-wire photoelectronic duct detector. <br />A5052-00 Replacement ionization detector board. <br />A5069-00 Replacement photoelectronic detector board. <br />A5064-D0 Replacement four-wire power board. <br />ACCESSORIES: <br />ST-1.5 Metal sampling tube, duct widths l' to 2'. <br />ST-3 Metal sampling tube, duct widths 2' to 4'. <br />ST-5 Metal sampling tube, duct widths 4' to 8'. <br />ST-10 Metal sampling tube, duct widths 8' to 12'. <br /> <br />ELECTRICAL RATINGS <br />for DH100ACDC (including detector) <br /> <br />T80-71-00 Replacement telescoping sampling tube..- <br />P48-55-00 Replacement end cap for T80-71-00. <br />RTS451 Remote test station. <br />RTS451 KEY Remote test station with key lock. <br />RA400Z Remote annunciator alarm LED. <br />APA451 Remote annunciator with piezo alarm. <br />M00400R Sensitivity test module. <br />F36-D9-00 Replacement air filters (two per package). <br />M02-04-DO Test magnet. <br />P48-21-DO End cap for metal sampling tubes. <br />S08-39-01 Photo replacement screen. <br />PA400B Mini-Alert sounder. <br />PS24LOB Mini-Alert add-on strobe. <br />PS12J24LENSC Ceiling-mount "SMOKE" 'ens. <br />PS12J24LENSW Wall-mount "SMOKE" lens. <br /> <br />Power supply voltage: 20 29 VDC 24 VAC, 50/60 Hz 120 VAC, 50/60 Hz 220/240 VAC, 50/60 Hz <br />Input capacitance: 270 F maximum 270 F maximum N/A N1A <br />Reset voltage: 3.0 VDC minimllTl 2.0 VAC minimllTl 10 V AC minimum 20 VAC minimum <br />Reset time (with RTS451): 0.03 to 0.30 seconds 0.03 to 0.30 seconds 0.03 to 0.30 seconds 0.03 to 0.30 seconds <br />Reset time (by power-down): 0.6 seconds mal<. 0.6 seconds mal<. 0.6 seconds max. 0.6 seconds mal<. <br />Power-up time: 34 seconds max. 34 seconds mal<. 34 seconds max. 34 seconds mal<. <br />Alarm response time: 2 to 17 seconds 2 to 17 seconds 2 to 17 seconds 2 to 17 seconds <br />Sensitivity test: See detector label. See detector label. See detector label. See detector label. <br />CURRENT LIMITATIONS (using no accessories): <br />Maximum standby current: 15mA 35 mA RMS 25 mA RMS. 15 mA RMS. <br />Maximum alarm current: 1 70mA 1 125 mA RMS I. 35 mA RMS. 25 mA RMS" <br /> <br />ACCESSORY CURRENT LOADS at 24 VDC <br />DEVICE STANDBY ALARM <br />APA451 12.5 mA maximum 30 mA maximllTl <br />PA400 OmA 15 mA maximllTl <br />RA400Z OmA 10 mA maximllTl <br />RTS451 12 mA. 7.5 mA maximlJl1 <br />RTS451 KEY 12mN 7.5 mA maximum <br /> <br />67_.1bl <br /> <br />6753e1ec.tbl <br /> <br />*NOTE: When a unit is powered at the 120 VAC or 220/ <br />240 VAC input, any combination of accessories may be <br />used such that the given accessory loads are: <br />. 60 mA or less in the STANDBY state. <br />. 110 mA or less in the ALARM state. <br /> <br />Contact Ratings <br /> <br />Alarm initiation contacts (SPST): 2.0 A @ 30 VAC/DC (0.6 power factor). <br />Alarm auxiliary contacts (DPOT): 10 A @ 30 VDC; 10 A @ 250 VDC. > <br />NOTE: Alarm auxiliary contacts must switch 100 mA minimum at 5 VDC. <br />Alarm auxiliary contacts shall not be connected to initiating circuits of <br />control panels. Use the alarm initiation contact for this purpose. <br />Trouble contacts (SPOT): 2.0 A @ 30 VDC (resistive). <br /> <br />Page 2 of 4 - DA-46765 <br />