Laserfiche WebLink
<br />'. <br /> <br /> <br />! <br />I <br />II <br /> <br />i <br /> <br /> <br />. <br />. <br />. <br />I <br />II <br />I <br />, <br /> <br /> <br />Page 3 of6 <br /> <br />G <br />T t. sampleW8soomprisooof GQtellModel "05305" Tilt Double Hung Vinyl Prime, one- <br />er~one{tiltloadingtype) double hung window, with an ovendl master frame size <br />masuring 54" wide X 71'~higbX 3-1I4" wide. The bottom sash measured 50-1/8" wide X <br />3 "bighovemll. The top sash measured 49-1f4" wide X 37-l/S" bi~ overall. The frame <br />erswere()f\VeIde.thni~redwith one screw in bottom coroersconstrttction. The sash <br />C trlers 'iVereofWeldecimitered type COmer const:r'Ucti{}o. Bottom Sash had an exterior <br />a1 'numscreen. Ea.ofrsash had (2) roam chirnneybloeks located in the jambs near the <br />b artci.es;One foamebimneybloek for each side of each sash. Each perimeter frame member <br />hoW's were filled with stirrofoarnpieces that measured to be 7fl6'~ x 9/16'. The bottom rail <br />o the: bottom sash had a anti bow sway bar attached to the rail and when the window would <br />sh t the bar would slide into an opening that was in the center of the sill. <br /> <br /> <br />WEATHERSTIPPING QUANTTIY <br /> <br />WIDTH X HEIGHf <br />CWCBES) <br />0.187 '\V x .23" ht <br /> <br />LOCA nON <br /> <br />Center Fin Pile Sen1 1 <br />none 0 <br />none 0 <br />Center Fin Pile Seal 1 <br />Center Fin Pile Seal 1 <br /> <br />si<ie face <br />none <br />none <br />exterior face <br />interior face <br /> <br />0.18'1" W x .23" ht <br />O.lS7"w x .23" ht <br /> <br />Center Fin Pile Seal <br /> <br />O.181"wx.23" ht <br /> <br />exterior face <br /> <br />Center Fin Pile Seal <br />Foam Filled Bulb Vinyl <br />with Fin <br />Center FinPile Seal <br />Center Fin.Pile Seal <br />CenterFixi :Pile.. Seal <br />Center fin Pile.Seal <br />Pile Seal <br /> <br />1 <br />I <br /> <br />0.187" wx .23" ht <br />0.3125" Dm. <br /> <br />Bottom face <br />Bottom face <br /> <br />1 <br />1 <br />1 <br />I <br />1 <br /> <br />0.187" w x .23" ht <br />O.1~7~w x.23" ht <br />O.l8Twx .23" ht <br />O.laTw x.23" ht <br />O.lUw x .35" ht <br /> <br />Exterior face <br />Side ~ <br />ExterilJrfa~ <br />Side face <br />l$ri()r faee <br /> <br />raton and Other Hardware: <br />. sash had two sets or(4)constant force balance shoes, one per jamb. One earn-type <br />p tock was attached to the center ofthe bottom sash meeting rail with keeper on top <br />sas meeting rail. One plastic tilt latch with thumb actuator was housed at each end of the top <br />f' .and interior meeting rail of the bottom sash. One die-cast pivot bar was fastened with (1) <br />scr . at each end of the bottom horizontalrnils ofthetopand bottom sash. Each sash had a <br />lift ilwith the top sash lift rail on the tOp ratl and the bottom sash tift rail on the bottom rail. <br />