Laserfiche WebLink
<br />07045 <br /> <br />Multiplex Fire Alarm Pull Station <br /> <br />Specifications <br /> <br />Features <br /> <br />. 07045 Single Action Pull Station <br />. Use with 07024 Series Fire Alarm <br />Control Panels with 07039 Multiplex Bus Module <br />. Easy Addressing via Rotary Switches <br />· Low Current Oraw <br />· Keylock Reset <br />. Replaceable Glass Breakrod Option <br />· Terminal Connections <br />· AOA Compliant <br />. UL Listed <br /> <br />Description <br /> <br />The Radionics' 07045 Multiplex Fire Alarm Pull Station is a <br />single action, UL listed fire alarm initiating device. The 07045 <br />has an easily identifiable pull down lever and contains an <br />integral break glass rod carrier. <br /> <br />The 07045 is compatible with the following accessory <br />devices: <br /> <br />. 0463 Oouble Action Lift Kit <br /> <br />. 0464 Red, Oeep Back Box <br /> <br />. 0465 Glass Break Tubes <br /> <br />The unit is a high quality manual fire alarm box constructed <br />entirely of non-toxic materials with a low profile and rounded <br />edges to fit most design applications. All components are <br />prepainted or have plated surfaces to inhibit corrosion. Non- <br />corroding screw terminals are provided for wire connections <br />to the 07045. <br /> <br />The 07045 is manufactured in conformance with the <br />standards set forth in the Americans with Oisabilities Act. <br /> <br />The 07045 has a white pull down lever in its center. Pulling <br />down the lever latches it into place. The 07045's normally <br />open contact switch is shorted causing an alarm on the fire <br />initiating loop. The pull down lever can not be reset unless <br />the correct key is inserted into the manual fire alarm box <br />lock and the unit is opened. The latching lever can then be <br />restored to its normal position. <br /> <br />When the 07045 is being reset and has a glass break rod <br />installed, all debris must be removed prior to installing another <br />rod to ensure the unit will dose and lock securely. <br /> <br /> <br />07045 Manual Fire Alarm Pull Station <br /> <br />Application <br /> <br />The 07045 Manual Fire Alarm Pull Station is an accessory <br />device for the Radionics 07024 FACP used in fire alarm <br />applications. Fire alarm boxes are generally installed near <br />building fire exits such as lobbies or stairways. Persons <br />evacuating the building during an emergency are able to <br />initiate an alarm by pulling down a lever. This alerts others <br />who may still be inside. Schools, factories, offices, and health <br />care facilities are typical applications. <br /> <br />The snap lock feature of the 07045 prevents the unit from <br />being reset without a key so the origin of the alarm can be <br />more easily determined. <br /> <br />Installation <br /> <br />The Radionics' 07045 Manual Fire Alarm Pull Station is a <br />UL listed fire alarm initiating device. The 07045 is installed <br />alone or with other approved mechanical devices on <br />Radionics 07024 FACP. Fire alarm boxes must be installed <br />according to codes set by the authority having jurisdiction. <br /> <br />The 07045 mounts to a standard flush or surface mounted <br />single gang switch box or plaster ring. Slotted screw holes <br />allow for correct positioning during installation. <br /> <br />Two corrosion resistant screw terminals are provided for wire <br />connections. All wiring and installation is subject to the <br />authority having jurisdiction. <br /> <br />Install, test and maintain this device according to the <br />Installation Guide, NFPA 72, Local Codes and the Authority <br />Having Jurisdiction. Failure to follow these procedures may <br />result in failure of the device to operate property. Radionics <br />is not responsible for devices that are improperty installed, <br />tested and maintained. <br /> <br />$ radionics <br /> <br />A member of the <br />Bosch Group <br />