09-8958 - Laserfiche WebLink

Browse Search

Jul 06 07 10:30a Porter #4513 8638581559 p.9 Series 94 -258 MULTIPRIMEL® HPC /Industrial Maintenance MULTIPRIME® Fast Dry 2.8 VOC General Surface Preparation In VOC regulated areas, all primers and finishes must comply with regional VOC regulations. Surface to be painted trust be free of dirt, rust, oil. water. grease, mill scale, wax, loose paint and other contaminants. Previously painted gloss surfaces in good condition must be dulled with fine sandpaper or steel wool. Recommended minimum surface preparation for rusted or new metal surfaces is SSPC -SP2 Hand Tool Cleaning or SSPC -SP3 Power Tool Cleaning. The surface to be coated must be dimensionally stable, dry, clean, and free of oil, grease, release agents, curing compounds, and other foreign materials. The service life of the coating is directly related to the surface preparation. WARNING( If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a property fitted NIOSH- approved respirator and prevent skin contact to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the USEPA National Lead Information Hotline at 1- 800 -424 -LEAD or log on to www.epa.govllead. In Canada contact a regional Health Canada office. Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation. FERROUS METAL: The minimum surface preparation is Hand Tool or Power Tool Clean per SSPC -SP2 or SP3. Recommended Primers Application Information Recommended Spread Rates: Wet Mils : 2.5 minimum to 3.3 maximum Wet Microns: 63.5 minimum to 83.8 maximum Dry Mils : 1.5 minimum to 2.0 msxi Dry Microns: 38.1 minimum to 50.8 max Application Equipment: Changes in application equipment, pressures and/or tip sizes may be required depending on ambient temperatures and application conditions. Conventional Spray: DeVillbiss or equivalent equipment. 1GA or MBC510 yarn, E or F tip and needle, 777 or 78 air cap. Fluid Directions for Use pressures are determined by job conditions. Atomizing air pressures of 50-60 psi are recommended. Stir thoroughly before using and frequently during use. Read all label Airless Spray: Equipment capable of 1500 psi minimum atomizing p and Material Safety Data Sheet (MSDS) information prior to use. Brush: Not recommended except for small areas. MSDS are available through our website or by calling 1- 800 - 441 -9695. Roller: Not recommended except for small areas. High - pressure injection of coatings into the skin by airless equipment Thinning: may cause serious injury. DO NOT THIN. Permissible temperatures daring application: Material: 50 to 90 °F 10 to 32 °C Ambient: 50 to 100°F 10 to 38 °C Substrate: 50 to I20°F 10 to 49 °C I'r'GAF eclicves the tmlual data preserved in this bulletin is eunettly saunas: towcsa, so Nmnntea of seamy. contactrasiveress, or pctra tame is Ores m implied. fr°provemett is maim Packaging: I Gallon (3.78L) 5- Galion (18.91) tslndoce may cauts future ttebaicar data to vary from wise, is in this bulletin. For complain, t•TO4rs mrgetnation visit our welt aloa ro :l l.80a.4:r -9 9$ Not all products arc ava>lnble in eh size a . Al containers : not Ml -fikd. ids PPG Hig' P+errormarx;a coatings PPG Atehitectusat Finishes, Inc. Tech s. PPG ehitcettual - Canada Onc P PG P lat c 1- 800 - -9695 Sctvicc 4 Kcno Blvd Castings - Cana Pittsburgh, PA 15272 Architect/Specifier: Brampton. Onuri 0 L6T 5E4 Bulletin: 94 -258 1- 888.774 -7732 (905) 790.5336 Additional copies of This bulletin can be obtuveetf front our web www.pittsbnrghpaints.cotn site or by calling 1 -800 -428 -7806. International 42) 43-2 Sala; 1- 877 -23$ 6841 (412)43 -2049 Rev. 2/2004