09-9335 - Laserfiche WebLink

Browse Search

October 20, 2004 DN -6995 • A1-310 N OT 1 F 1 E R® NP- 100(A) and NP- 100T(A) Addressable Photoelectric Detectors Section: Addressable GENERAL The NP- 100(A) and NP- 100T(A) addressable, low- profile plug -in u MARYLAND photoelectric detectors use a state -of- the -art photoelectric sens- ing chamber with communications to provide open area protec- State Fire Marshal ton and are used exclusively with NOTIFIER's FireWarden -100 Permit # 2173 Addressable Fire Alarm Control Panel (FACP). The NP- 100T(A) LISTED adds thermal sensors that will alarm at a fixed temperature of 135 °F (57 °C). Since these detectors are addressable, they will S1115 help emergency personnel quickly locate a fire during its early stages, potentially saving precious rescue time while also reduc- ing property damage. Two LEDs on each sensor light to provide a local, visible sensor indication. Remote LED annunciator capabil- ity is available as an optional accessory (P /N RA400Z). FEATURES SLC loop: • Two -wire loop connection. • Unit uses base for wiring. Addressing: • Addressable by device. 6934pho, too • Direct Decade 01 – 99 (FireWarden -100) entry of address. t �� Architecture: • Unique single- source, dual - chamber design to respond quickly NP- 100(A) and dependably to a broad range of fires. with • Sleek, low - profile design. B710LPbase • Integral communications and built -in type identification. • Built -in tamper - resistant feature. • Removable cover and insect- resistant screen for simple field` cleaning. Operation: • Withstands air velocities up to 4,000 feet -per- minute (20 m/ sec.) without triggering a false alarm. • Factory preset at 1.5% nominal sensitivity for panel alarm thresh- 6935pho1 tpg old level. Y • Visible LED "blinks" when the unit is addressed (communicat- '' ing with the fire panel) and latches on in alarm. NP - 100T(A) with Mechanicals: B710LP base • Sealed against back pressure. • Direct surface mounting or electrical box mounting. • Mounts to: single -gang box, 3.5" (8.89 cm) or 4.0" (10.16 cm) SPECIFICATIONS octagonal box, or 4.0" (10.16 cm) square electrical box (using range: Voltage 15 – 32 VDC (peak). plaster ring — included). g g (p ) . Other system features: Standby current: 300 pA @ 24 VDC. • Fully coated circuit boards and superior RF /transient protec- LED current: 6.5 mA @ 24 VDC (latched "ON "). tion. Air velocity: 4,000 ft. /min. (20 m /sec.) maximum. • 94 -VO plastic flammability rating. Diameter: 6.1" (15.5 cm) installed in B710LP base. • Low standby current. Height: 2.1" (5.33 cm) installed in B710LP base. Options: Weight: 3.6 oz. (102 g). • Remote LED output connection (P /N RA400Z). Operating temperature range: for NP- 100(A): 0 °C to 49 °C (32 °F to 120 °F); for NP- 100T(A): 0 °C to 38 °C (32 °F to 100 °F). Temperature: 0 °C – 49°C (32 °F – 120 °F). Relative humidity: 10% – 93 %, non - condensing. This document is a Honeywell company. ISO 9001 This document t is not intended to be used for installation purposes. We try to keep our product information up -to -date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. GER For more information. contact NOTIFIER. Phone. (203) 484 -7161 FAX: (203) 484 -7118 EIICYlEEM I MAIMIF#CllillS 0 NOTIFIER' 12 Clintonville Road, Northford, Connecticut 06472 QUALITY SYSTEMS DN -6995 • 10/20/04 — Page 1 of 2